03 Enhanced Ping Tools Guide Line V1.8 English Version

HUAWEI TECHNOLOGIES CO., LTD.

www.huawei.com

Huawei Confidential

Security Level:

英文标题 :40-47pt

副标题 :26-30pt

字体颜色 : 反白内部使用字体 :

FrutigerNext LT Medium

外部使用字体 : Arial

中文标题 :35-47pt

字体 : 黑体副标题 :24-28pt

字体颜色 : 反白字体 : 细黑体

23/4/17

Enhanced Ping Tools Guide Line

英文目录标题 :35-40pt

颜色 : R153 G0 B0

内部使用字体 :

FrutigerNext LT Medium


中文目录标题 :35-40pt

颜色 : R153 G0 B0

字体 : 黑体

英文目录正文 :28-30pt

子目录 (2-5 级 ) :20-30pt

颜色 : 黑色内部使用字体 :

FrutigerNext LT Regular


中文目录正文 :28-30pt

子目录 (2-5 级 ):20-30pt

颜色 : 黑色字体 : 细黑体

目录

• Function description and main interface

introduction

• Operation step introduction

• Analyze result introduction

• Simple version introduction

• Application example

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential

This tools is a auxiliary tools using for

exception of processing special protocol,

transmission QoS not reach target and

transmission bandwidth limited problem.

You can construct special type package and

set the send rate, to shoot the transmission

trouble.

1 Function description and main interface


Function 1:construct package1 The tools support ARP 、 ICMP 、 UDP 、 TCP package

2 You can set the parameter of package head


Function 2:Send packageTwo type:1 constant rate 2 custom rate


Main interface

Send rate observer area

Head setting area

package payload area

Send and receive package number display area

Configuration control area

Send package start control


Mainly introduce construct package and send package

setup(use ICMP as example) ：

2 Operation step

Step 1:selet protocol type


2 Operation stepStep 2:set package head

Set mac parameterMAC DA:destination MACMAC SA:source MAC 。 Normal not modify, use the address inspect by the toolVLAN ： if you need to construct package with vlan, then input VLAN IDPriority ： set VLAN priorityEther type ： up layer protocol type

Set IP parameterDSCP:set IP priorityIdentifier:set the begin ID of IPFlags:set IP ‘s flagTime to live:set IP’s TTLProtocol:set the type of protocol of IP’s payloadCheck sum ： set heck sum’s valueSource IP:set IP’s source address, also can select from the dropdownlistDestination IP:set the destination address of IP

设置 ICMP 头域Type:select ICMP type,also can select from dropdownlistCode:set the code value of ICMP packageCheck sum:set the check sum of ICMPIdentifier:set the ID value of ICMPSequence:SET the begin sequence value of ICMP


2 Operation stepStep 3:select network cardSelect from the dropdownlist of Device


2 Operation stepSetp 4:set the sending parameter

Statistic:send package,and count the sending rate

Packet pour/not stat:only send package,not count the send rate information

Constant rate:select from the dropdownlist, max is 5M Bps

Custom rate:set the number of package （ Repeat ） ,sent interval （ Break ） ,size （ PkSize ）to set the send rateSend rate (bps)=

In Time/s:set the sending total time

In Num ： :set the sending times


2 Operation stepStep 5:begin send package

Begin send

Package send informationNew:the delay of the latest package sendMax:the max delayMin:the min delayMean:average delaySend:sent package countReceive:received package countDrop:discard package count

You can view the count of package after stop send


2 Operation stepTypical configuration

21M bps:Repeat:500Break:100PktSize ： 1000





3 analyze result introduction

1:sent result

ARP package receive and send result

ICMP package receive and send result

UDP package receive and send result

TCP package receive and send result


3 analyze result introduction

2:send rate informationCount the detail information of this send:Max delay:3.236 msMin delay:0.491 msAverage delay:1.948 msSend total count:10500Receive total count:10483Lost total count:17

Receive rate:1.096 BpsSend rate:1.019Bps

Note:the unit is Bps, normally the rate is bps ， the formula isN Bps = N * 8 bps

note ：Because of the performance of PC, it maybe reflect the correct of statistic


4 simple version introduction1 consider the application condition of live network, take

out the ICMP function and optimize the tool

2 can inspect the delay , lose, jitter of package

analyze result introduction


5 application example

1:one office need to test the QoS of IUB with vlan

configuration

Test process:use two PC instead of RNC and NodeB,

execute ping to check the package delay and lose

condition

step

1 copy the tools to PC,set the ip address of the two pc;

2 send package in PC1,set vlan,ip and other parameter,then view the package delay and lose;


5 application example

2 ： one office ps traffic rate is low, and doubt the

limitation of transmission network

Trouble shouting process:use this tool to test ,the rate can

only reach 5Mbps

step

1 copy the tools to PC2 set send parameter of according to request,view the rate,find the fast rate by gradually change the send

flux

Thank youwww.huawei.com

03 Enhanced Ping Tools Guide Line V1.8 English Version

Documents

Transcript of 03 Enhanced Ping Tools Guide Line V1.8 English Version