02 RN31552EN30GLA0 the Physical Layer Rel99
-
Upload
salman-zaheer -
Category
Documents
-
view
216 -
download
0
Transcript of 02 RN31552EN30GLA0 the Physical Layer Rel99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
1/85
1 © Nokia Siemens Networks RN31552EN30GLA0
The Physical Layer – Rel. 99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
2/85
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
3/85
3 © Nokia Siemens Networks RN31552EN30GLA0
The Physical Layer – Rel. 99
• Channel Mapping
• Transport Channel Formats• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel Downlink
• Dedicated Physical Channel Uplink
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
4/85
4 © Nokia Siemens Networks RN31552EN30GLA0
In UMTS there are three different types of channels:
• Logical Channels• Logical Channels transmit specific contents.
• There are e.g. logical channel to transmit the cell system information, paging information, or user data.• Logical channels are offered as data transfer service by the Medium Access Control (MAC) layer to the next
higher layer.
• Consequently, logical channels are in use between the mobile phone and the RNC.
• Transport Channels (TrCH)• MAC layer is using the transport service of the lower lower, the Physical layer.
• MAC layer is responsible to organise the logical channel data on transport channels. This process is called
mapping.
• In this context, MAC layer is also responsible to determine the used transport format.
• The transport of logical channel data takes place between the UE and the RNC.
• Physical Channels (PhyCH)• The physical layer offers the transport of data to the higher layer.
• The characteristics of the physical transport have to be described.
• When we transmit information between the RNC and the UE, the physical medium is changing.
• Between the RNC and the Node B, where we talk about the interface Iub, the transport of information is
physically organised in so-called Frames.• Between the Node B and the UE, where we find the WCDMA radio interface Uu, the physical transmission is
described by physical channels.
• A physical channel is defined by the UARFCN and the a spreading code in the FDD mode.
Radio Interface Channel Organisation
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
5/855 © Nokia Siemens Networks RN31552EN30GLA0
Logical Channelscontent is organised in separate channels, e.g.
System information, paging, user data, link management
Transport Channelslogical channel information is organised on transport channel
resources before being physically transmitted
Physical Channels(UARFCN, spreading code)
FramesIub interface
Radio Interface Channel Organisation
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
6/856 © Nokia Siemens Networks RN31552EN30GLA0
There are two types of logical channels (FDD mode):
1) Control Channels (CCH):
• Broadcast Control Channel (BCCH)
• System information is made available on this channel.• The system information informs the UE about the serving PLMN, the serving cell, neighbourhood lists,
measurement parameters, etc.
• This information permanently broadcasted in the DL.
• Paging Control Channel (PCCH)
• Given the BCCH information the UE can determine, at what times it may be paged.
• Paging is required, when the RNC has no dedicated connection to the UE.
• PCCH is a DL channel.
• Common Control Channel (CCCH)• for UL & DL Control information
• in use, when no RRC connection exists between the UE and the network
• Dedicated Control Channel (DCCH)
• UL & DL: Layer 3 Signalling dedicated to a specific radio link.
2) Traffic Channels (TCH):
• Dedicated Traffic Channel (DTCH)
• UL & DL: dedicated resources for User data transmission between the UE and the network
• Common Traffic Channel (CTCH)
• DL only: User data to be transmitted point-to-multipoint to a group of UEs.
Logical Channels
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
7/857 © Nokia Siemens Networks RN31552EN30GLA0
Logical Channels are mapped onto Transport Channels. There are two types of Transport Channels (FDD mode):
a) Common Transport Channels:
• Broadcast Channel (BCH): carries the BCCH information.
• Paging Channel (PCH): used to page a UE in the cell. It carries the PCCH information or to notify UEs about cellsystem information changes.
• Forward Access Channel (FACH): The FACH is a DL channel. Control information, but also small amounts of user
data can be transmitted on this channel.
• Random Access Channel (RACH): UL channel used by the UE to transmitt small amounts of data; no Dedicated
resources are required. Contention based channel, i.e. several UE may attempt to access UTRAN simultaneously.
b) Dedicated Transport Channels:
Dedicated Channel (DCH): Dedicated resources can be allocated both UL & DL to a UE; exclusively in use for thissubscriber.
HS-Downlink Shared Channel (HS-DSCH) & E-DCH
Transport Channels for DL HSDPA respectively UL HSUPA data transfer
Physical Channels are characterised by:• UARFCN,
• Scrambling Code,
• Channelisation Code (optional),
• start and stop time, and
• relative phase (in the UL only, with relative phase being 0 or /2)
• Transport channels can be mapped to physical channels.
• There are physical channels existing, which are generated at the Node B only, as can be seen on the next figures.
• The details of the physical channels is described in detail within this module (see following pages).
Transport Channels (TrCH) & Physical Channels (PhyCH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
8/85
8 © Nokia Siemens Networks RN31552EN30GLA0
P-CCPCHPCH
BCH
CTCH
DCCH
CCCH
PCCH
BCCH
DCH
CPICH
S-SCH
P-SCH
FACH
HS-
DSCH
AICH
HS-PDSCH
DPDCH
S-CCPCH
DTCH
PICH
Logical
Channels
Transport
Channels
Physical
Channels
E-AGCH
Channel Mapping DL (Network Point of View)
HS-SCCH
F-DPCH
E-RGCHE-HICH
DPCCH
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
9/85
9 © Nokia Siemens Networks RN31552EN30GLA0
DCCH
DCH
DPDCH
DTCH
Logical
Channels
Transport
Channels
Physical
Channels
RACH
CCCH PRACH
DPCCH
Channel Mapping UL (Network Point of View)
E-DPCCH
E-DPDCHE-DCHHS-DPCCH
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
10/85
10 © Nokia Siemens Networks RN31552EN30GLA0
Channel configuration examples
AMR call
• The data transferred during AMR call consists of
• Speech data
• L3 signalling
• L1 signalling
• User data is transferred on DTCH logical channel
• RT connection uses always DCH transport channel
• DCH transport channel is mapped on DPCH (DPDCH + DPCCH)
AMR + PS call (Multi-RAB)
• Additional stream of user data
• NRT data
• Also configurations with HS-DSCH possible
NRT PS call
• Different configurations utilising DCH, FACH/RACH, HS-DSCH or HS-DSCH/E-DCHpossible
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
11/85
11 © Nokia Siemens Networks RN31552EN30GLA0
Example – Channel configuration during call
Logical
ChannelsTransport
Channels
Physical
Channels
Data
DCCH0-4
DCH2-4
DPDCH
DTCH1 DPCCH
RRC
signalling
Speech
data
DCH1
AMR speech connection utilises multiple transport channels
RRC connection utilises multiple logical channels
DPCCH for L1 control data
DCH5DTCH2NRT
data
AMR speech
+NRT data
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
12/85
12 © Nokia Siemens Networks RN31552EN30GLA0
The Physical Layer – Rel. 99
• Channel Mapping
• Transport Channel Formats• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel Downlink
• Dedicated Physical Channel Uplink
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
13/85
13 © Nokia Siemens Networks RN31552EN30GLA0
Transport Channel Formats
• Transport Channels are used to exchange data between the MAC-layers in the UE and the RNC.
• The data is hereby organised in Transport Blocks (TB). A Transport Block is the basic data unit.
• The MAC layer entities use the services offered to them by the Physical layer to exchange TransportBlocks.
• One Transport Block can be transmitted only over one Transport Channel. Several Transport Blockscan be simultaneously transmitted via a Transport Channel in one transport data unit to increase thetransport efficiency.
• The set of all Transport Blocks, transmitted at the same time on the same transport channel (betweenthe MAC layer and the physical layer) is referred to as Transport Format Set (TFS).
• Transport Blocks and Transport Block Sets are characterised by a set of attributes:
• Transport Block Size
• The transport block size specifies the numbers of bits of one Transport Block.
• If several Transport Blocks are transmitted within one TBS, then all TBs have the same size.
• Please note, that the transport block size among different TBSs – which are transmitted at different times on one transpochannel - can vary.
• Transport Block Set Size
• This attribute identifies the numbers of bits in one TBS.
• It must be always a multiple of the transport block size, because all TBs transmitted in one TBS have the same size.
• (continued on the next text slide)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
14/85
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
15/85
15 © Nokia Siemens Networks RN31552EN30GLA0
Transport Blocks and Transport Block Sets are characterised by a set of attributes (continued):
• Transmission Time Interval (TTI)
•The TTI specifies the transmission time distance between two subsequent TBSs, transferred
between the MAC and the PHY layer.•In the PHY layer, the TTI also identifies the interleaving period. Following TTI periods are
currently specified:
- 2 ms (HS-DSCH), 10 ms, 20 ms, 40 ms, and 80 ms
• Error Protection Scheme
•When data is transmitted via a wireless link, it faces a lot of distortion and can thus easily
corrupted.
•Redundancy is added to the user data to reduce the amount of losses on air.•In UMTS, three error protection schemes are currently specified:
•convolutionary coding with two rates: 1/2 and 1/3,
•turbo coding (rate 1/3), and
•no channel coding (this coding type is scheduled for removal from the UMTS
specifications).
• Size of CRC
•CRC stands for cyclic redundancy check. Each TBS gets an CRC.•The grade of reliability depends on the CRC size, which can be 0, 8, 12, 16, and 24 bits.
Transport Channel Formats
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
16/85
16 © Nokia Siemens Networks RN31552EN30GLA0
TB Transport Block TF Transport FormatTBS Transport Block Set TFS Transport Format Set
TFC Transport Format CombinationTFCS Transport Format Combination Set
DCH 2
DCH 1
TB TB TB
TB
TB
TB
TB
TB
TBS
TF
TFS
TFC
TFCS
TTI TTI
TTI
TTI
TTITTI
TB
TB
TB
Transport Formats
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
17/85
17 © Nokia Siemens Networks RN31552EN30GLA0
• The above description refers to a situation, where the MAC-layer hands the TBS to the PHY layer.
This happens in the UE. But TBSs are normally exchanged between the UE and the RNC. As a
consequence, the TBS must be transmitted over an AAL2 virtual channel between the RNC and the
Node B. The TBS is packet into a frame protocol defined for the traffic channel.• Different TBSs can be transmitted in one Transport Channel.
• How do MAC and PHY layer know, what kind of TBS they exchanged?
• When a transport channel is setup – or modified – the allowed Transport Block Sets are specified.
• Each allowed TBS gets a unique Transport Format Indicator (TFI).
• All TFIs of a Transport Channel are summarised in the Transport Format Set (TFS). • The TF consists of two parts (FDD mode):
•Semi-static part
•The attributes belonging to the semi-static part are set by the RRC-layer.
•They are valid for all TBSs in the Transport Channel.
•Semi-static attributes are the Transmission Time Interval (TTI), the error correction
scheme, the CRC size, and the static rate matching parameter (used by the PHY layer for
dynamic puncturing if the TBS is too long for the radio frame).
•Dynamic part
•The dynamic part comprises attributes, which can be changed by the MAC layer
dynamically.
•The affected attributes are the Transport Block Size & Transport Block Set Size.
Transport Channel Formats
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
18/85
18 © Nokia Siemens Networks RN31552EN30GLA0
MAC Layer
PHY Layer
RRC Layer
c o n f i g u r a t i o n
Semi-Static Part
• TTI
• Channel Coding
• CRC size
• Rate matching
Dynamic Part• Transport Block Size
• Transport Block Set Size
Transport Format
Example: semi-static part dynamic part:
- TTI = 10 ms
- turbo coding - transport block size: 64 64 64 128- CRC size = 0 - transport block set size: 1 2 4 2
- ...
TFI1 TFI2 TFI3 TFI4
TrCHs
Transport Formats
TrCH: Transport Channel
TBS: Transport Block Set
TFI: Transport Format Indicator
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
19/85
19 © Nokia Siemens Networks RN31552EN30GLA0
• The PHY layer can multiplex several Transport Channels in one “internal“ Transport Channel, called
Coded Composite Transport Channel (CCTrCH).
• This CCTrCH can be transmitted on one or several physical channels. Consequently, the TCSs ofdifferent Transport Channels can be found in one radio frame.
• The Transport Format Combination Set (TFCS) lists all allowed Transport Format Combinations
(TFC).
• A Transport Format Combination Indicator (TFCI) is then used to indicate, what kind of Transport
Format Combination is found on the radio frame. You can find TFCI-fields for instance in the S-CCPCH. The TFCS is set by the RRC protocol.
• The table on the following slide lists the allowed Transport Formats for the individual Transport
Channels (FDD mode only).
Transport Channel Formats
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
20/85
20 © Nokia Siemens Networks RN31552EN30GLA0
1...5000 bits
granularity: 1 bit
0...5000 bitsgranularity: 1 bit
0...5000 bits
granularity: 1 bit
246 bits
0...5000 bits
granularity: 1 bit
246 bits
1...200000 bits
granularity: 1 bit
0...200000 bitsgranularity: 1 bit
0...200000 bits
granularity: 1 bit
0...200000 bits
granularity: 1 bit
20 ms
10 ms
10, 20, 40& 80 ms
10 & 20
ms
10, 20, 40
& 80 ms
BCH
FACH
RACH
PCH
DCH
convolutional 1/2
convolutional 1/2
convolutional 1/2& 1/3; turbo 1/3
convolutional 1/2
convolutional 1/2
& 1/3; turbo 1/3
16
0, 8, 12,
16 & 24
0, 8, 12,16 & 24
0, 8, 12,
16 & 24
0, 8, 12,
16 & 24
Transport
Block Size
Transport
Block Set SizeTTI
coding types
and rates
CRC
size
Semi-static PartDynamic Part
3GPP TS 25.302 V5.9.0
Transport Format Ranges
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
21/85
21 © Nokia Siemens Networks RN31552EN30GLA0
Example: Transport Formats in AMR call
• The AMR codec was originally developed and standardized by the EuropeanTelecommunications Standards Institute (ETSI) for GSM cellular systems. It has been
chosen by the Third Generation Partnership Project (3GPP) as the mandatory codec forthird generation (3G) cellular systems. It supports 8 encoding modes with bit ratesbetween 4.75 and 12.2 kbps.
• Feature of the AMR codec is Unequal Bit-error Detection and Protection (UED, UEP).
• The UEP/UED mechanisms allow more speech over a lossy network by sorting the bitsinto perceptually more and less sensitive classes (A, B, C).
• A frame is only declared damaged and not delivered if there are bit errors found in the mostsensitive bits (Class A).
• Acceptable speech quality results if the speech frame is delivered with bit errors in the lesssensitive bits (Class B, C). Decoder uses error concealment algorithm to hide the errors.
• On the radio interface, one Transport Channel is established per class of bits i.e. DCH Afor class A, DCH B for class B and DCH C for class C. Each DCH has a different transport
format combination set which corresponds to the necessary protection for thecorresponding class of bits as well as the size of these class of bits for the various AMRcodec modes.
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
22/85
22 © Nokia Siemens Networks RN31552EN30GLA0
Example: Transport Formats in AMR call
DCH 1: AMR class Abits
TBS size: 1TB size: 39 bits
(SID)
TBS size = 0
(DTX)
TBS size: 1TB size: 103 bits
TTI = 20 ms
TBS size = 0
(DTX)
DCH 2: AMR class Bbits
DCH 3: AMR class Cbits
Convolutional codingCoding rate: 1/3
TTI = 20 ms
Coding type: convolutionalCoding rate: 1/3
CRC size: 12 bits CRC size: 0 bits CRC size: 0 bits
TTI = 20 ms
Coding rate: 1/2Convolutional coding
DCH 24: RRCConnection
TBS size = 0
(DTX)
TBS size = 1TB size: 148 bits
TTI = 40 ms
Coding type: convolutionalCoding rate: 1/3
CRC size: 16 bits
TBS size:1TB size: 81 bits
TBS size: 1TB size: 60 bits
TBS size = 0
(DTX)
12.2 kbit/s3.7 kbit/s
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
23/85
23 © Nokia Siemens Networks RN31552EN30GLA0
The Physical Layer – Rel. 99
• Channel Mapping
• Transport Channel Formats• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel Downlink
• Dedicated Physical Channel Uplink
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
24/85
24 © Nokia Siemens Networks RN31552EN30GLA0
Cell Synchronisation
• When a UE is switched on, it starts to monitor the radio interface to find a suitable cell to camp on butit has to determine, whether there is a WCDMA cell nearby.
• If a WCDMA cell is available, the UE has to be synchronised to the DL transmission of the system
information – transmitted on the physical channel P-CCPCH – before it can make a decision, in howfar the available cell is suitable to camp on.
• Initial cell selection is not the only reason, why a UE wants to perform cell synchronisation. Thisprocess is also required for cell re-selection and the handover procedure.
• Cell synchronisation is achieved in 3 steps*:
• Step 1: Slot synchronisation
• During the first step of the cell search procedure the UE uses the SCH’s primary synchronisation code to acquire slotsynchronisation to a cell. This is typically done with a single matched filter (or any similar device) matched to the primary
synchronisation code which is common to all cells. The slot timing of the cell can be obtained by detecting peaks in thematched filter output.
• Step 2: Frame synchronisation and code-group identification
• During the second step of the cell search procedure, the UE uses the SCH’s secondary synchronisation code to findframe synchronisation and identify the code group of the cell found in the first step. This is done by correlating thereceived signal with all possible secondary synchronisation code sequences, and identifying the maximum correlationvalue. Since the cyclic shifts of the sequences are unique the code group as well as the frame synchronisation isdetermined.
• Step 3: Scrambling-code identification
• During the third and last step of the cell search procedure, the UE determines the exact primary scrambling code used by
the found cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICHwith all codes within the code group identified in the second step. After the primary scrambling code has been identified,the Primary CCPCH can be detected. And the system- and cell specific BCH information can be read.
• If the UE has received information about which scrambling codes to search for, steps 2 and 3 abovecan be simplified.
* further Information about Primary- & Secondary Synchronisation
Channels and Code Groups can be found on the following pages
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
25/85
25 © Nokia Siemens Networks RN31552EN30GLA0
Cell Synchronisation
• Detect cells• Acquire slot
synchronisation
Phase 1 – P-SCH
Phase 2 – S-SCH
Phase 3 – P-CPICH
• Acquire frame synchronisation
• Identify the code group of thecell found in the first step
• Determine the exact primary
scrambling code used by thefound cell
• Measure level & quality of the
found cell
PriScrCode
WCEL; 0..511; 1; no default
(Range; Step; Default)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
26/85
26 © Nokia Siemens Networks RN31552EN30GLA0
Cell synchronisation is achieved with the Synchronisation Channel (SCH). This channel divides up into
2 sub-channels:
Primary Synchronisation Channel (P-SCH)
• A time slot lasts 2560 chips.
• The P-SCH only uses the first 10% of a time slot.
• A Primary Synchronisation Code (PSC) is transmitted the first 256 chips of a time slot. This is the case
in every UMTS cell.
• If the UE detects the PSC, it has performed TS and chip synchronisation.
Secondary Synchronisation Channel (S-SCH)
• The S-SCH also uses only the first 10% of a timeslot
• Secondary Synchronisation Codes (SSC) are transmitted.
• There are 16 different SSCs, which are organised in a 10 ms frame (15 timeslots) in such a way, that
the beginning of a 10 ms frame can be determined, and 64 different SSC combinations within a 10 ms
frame are identified.
• There is a total of 512 primary scrambling codes, which are grouped in 64 scrambling code families,
each family holding 8 scrambling code members.
• The 15 SSCs in one 10 ms frame identify the scrambling code family of the cell‘s DL scrambling code.
Cell Synchronisation
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
27/85
27 © Nokia Siemens Networks RN31552EN30GLA0
Cp = Primary Synchronisation CodeCs = Secondary Synchronisation Code
10 ms Frame
CP CP
2560 Chips 256 Chips
Cs1 Cs2 Cs15
Slot 0 Slot 1 Slot 14
CP CP CP
Cs1
Primary Synchronisation Channel (P-SCH)
Secondary Synchronisation Channel (S-SCH)
Slot 0
Synchronisation Channel (SCH)
PtxPr imarySCH
-35..15; 0.1; -3 dB
PtxSecSCH
-35..15; 0.1; -3 dB
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
28/85
28 © Nokia Siemens Networks RN31552EN30GLA0
15
15
scrambling
code group
group 00
group 01
group 02
group 03
group 05
group 04
group 62
group 63
1 1 2 8 9 10 15 8 10 16 2 7 15 7 16
1 1 5 16 7 3 14 16 3 10 5 12 14 12 10
1 2 1 15 5 5 12 16 6 11 2 16 11 12
1 2 3 1 8 6 5 2 5 8 4 4 6 3 7
1 2 16 6 6 11 5 12 1 15 12 16 11 2
1 3 4 7 4 1 5 5 3 6 2 8 7 6 8
9 11 12 15 12 9 13 13 11 14 10 16 15 14 16
9 12 10 15 13 14 9 14 15 11 11 13 12 16 10
slot number
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
11
11 11
11 11
11 11
11 11
15
15
15
15 15
15
15
15 15
15 15
5
5
SSC Allocation for S-SCH
I monitorthe S-SCH
C Pil t Ch l (CPICH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
29/85
29 © Nokia Siemens Networks RN31552EN30GLA0
• With the help of the SCH, the UE was capable to perform chip, TS, and frame synchronisation.
•Even the cell‘s scrambling code group is known to the UE.
• But in the initial cell selection process, it does not yet know the cell‘s primary scrambling code.
• There is one primary scrambling code in use over the entire cell, and in neighbouring cells, different
scrambling codes are in use.
•There exists a total of 512 primary scrambling codes.
• The CPICH is used to transmit in every TS a pre-defined bit sequence with a spreading factor 256.
•The CPICH divides up into a mandatory Primary Common Pilot Channel (P-CPICH) and optional
Secondary CPICHs (S-CPICH).
• The P-CPICH is in use over the entire cell and it is the first physical channel, where a spreading code
is in use.
• A spreading code is the product of the cell‘s scrambling code and the channelisation code.
•The channelisation code is fixed: Cch,256,0. i.e., the UE knows the P-CPICH‘s channelisation code,
and it uses the P-CPICH to determine the cell‘s primary scrambling code by trial and error.
• The P-CPICH is not only used to determine the primary scrambling code. It also acts as:-
•phase reference for most of the physical channels,
•measurement reference in the FDD mode (and partially in the TDD mode).
• There may be zero or several S-CPICHs. Either the cell‘s primary scrambling code or its secondary
scrambling codes can be used. In contrast to the P-CPICH, it can be broadcasted just over a part ofthe cell.
Common Pilot Channel (CPICH)
P i C Pil t Ch l (P CPICH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
30/85
30 © Nokia Siemens Networks RN31552EN30GLA0
CP
2560 Chips 256 Chips
Synchronisation Channel (SCH)
P-CPICH
10 ms Frame
applied speading code =
cell‘s primary scrambling code Cch,256,0
• Phase reference
• Measurement reference
P-CPICH Cell scrambling
code? I get it with
trial & error!
Primary Common Pilot Channel (P-CPICH)
PtxPr imaryCPICH
-10..50; 0.1; 33 dBm
(20 W sector)
CPICH M t R f
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
31/85
31 © Nokia Siemens Networks RN31552EN30GLA0
• The UE has to perform a set of L1 measurements, some of them refer to the CPICH channel:
• CPICH RSCP
• RSCP stands for Received Signal Code Power.
• The UE measures the RSCP on the Primary-CPICH.
• The reference point for the measurement is the antenna connector of the UE.
• The CPICH RSCP is a power measurement of the CPICH.
• The received code power may be high, but it does not yet indicate the quality of the received
signal, which depends on the overall noise level.
• UTRA carrier RSSI.
• RSSI stands for Received Signal Strength Indicator.
• The UE measures the received wide band power, which includes thermal noise & receiver
generated noise.
• The reference point for the measurements is the antenna connector of the UE.
• CPICH Ec/No
• The CPICH Ec/No is used to determine the “quality“ of the received signal.
• It gives the received energy per received chip divided by the band‘s power density.
• The “quality“ is the primary CPICH‘s signal strength in relation to the cell noise.
• (Please note, that transport channel quality is determined by BLER, BER, etc. )
• If the UE supports GSM, then it must be capable to make measurements in the GSM bands, too. The
measurements are based on the GSM carrier RSSI
• The wideband measurements are conducted on GSM BCCH carriers.
CPICH as Measurement Reference
P CPICH as Measurement Reference
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
32/85
32 © Nokia Siemens Networks RN31552EN30GLA0
Received Signal Code Power (in dBm)CPICH RSCP
received energy per chip divided by the power density in the band (in dB)CPICH Ec/No
received wide band power, including thermal noise & noise generated in the receiverUTRA carrier
RSSI
CPICH Ec/No =CPICH RSCP
UTRA carrier RSSI
CPICH Ec/No
0: < -24
1: -23.5
2: -23
3: -22.5
...
47: -0.548: 0
49: >0
Ec/No values in dB
CPICH RSCP
-5: < -120
-4: -119
:
0: -115
1: -114
:89: -26
90: -25
91: ≥ -25
RSCP values in dBm
GSM carrier RSSI
0: -110
1: -109
2: -108
:
71: -39
72: -38
73: -37
RSSI values in dBm
P-CPICH as Measurement Reference
Primary Common Control Physical Channel (P CCPCH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
33/85
33 © Nokia Siemens Networks RN31552EN30GLA0
• The UE knows the cell‘s primary scrambling code.
• It now wants to gain the cell system information, which is transmitted on the physical channel P-
CCPCH.
• The channelisation code of the P-CCPCH is also known to the UE, because it must be Cch,256,1
in
every cell for every operator.
• By reading the cell system information on the P-CCPCH, the UE learns everything about the
configuration of the remaining common physical channels in the cell, such as the physical channels for
paging and random access.
• As can be seen from the P-CCPCH‘s channelisation code, the data rate for cell system information is
fixed.
• The SCH is transmitted on the first 256 chips of a timeslot, thus creating here a peak load.
• The cell system information is transmitted in the timeslot except for the first 256 chips. By doing so, a
high interference and load at the beginning of the timeslot is avoided.
• This leads to a net data rate of 27 kbps for the cell system information.
• Channel estimation is done with the CPICH, so that no pilot sequence is required in the P-CCPCH.
• (The use of the pilot sequence is explained in the context of the DPDCH later on in this
document.)
• There are also no power control (TPC) bits transmitted to the UE‘s.
Primary Common Control Physical Channel (P-CCPCH)
Primary Common Control Physical Channel (P CCPCH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
34/85
34 © Nokia Siemens Networks RN31552EN30GLA0
CP
2560 Chips 256 Chips
Synchronisation Channel (SCH)
P-CCPCH
10 ms Frame
P-CCPCH Finally, I get the
cell system
information
• channelisation code: Cch,256,1
• no TPC, no pilot sequence
• 27 kbps (due to off period)
• organised in MIBs and SIBs
Primary Common Control Physical Channel (P-CCPCH)
PtxPr imaryCCPCH
-35..15; 0.1; -5 dB
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
35/85
Cell Synchronization and Sectorised Cells
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
36/85
36 © Nokia Siemens Networks RN31552EN30GLA0
Node B with three
sectorised cells
cell1
cell2
cell3
1 TS
BFN
SCH
SCH
SCH
SCH
SCH
SCH
SCH
SFN = BFN + T_cell1
SFN = BFN + T_cell2
SFN =
BFN + T_cell3
T_cell3
T_cell1
T_cell2
SFN: Cell System Frame Numberrange: 0..4095 frames
T_cell: n 256 chips, n = 0..9
cell3 cell2
cell1
SCH
Cell Synchronization and Sectorised Cells
TcellWCELL; 0..2304 chip;
256 chip; no default
Tcell: Timing delay used for defining the start of SCH, P-
CPICH, P-CCPCH in a cell relative to BFN
BFN: Node B Frame Number
RFN: RNC Frame Number
SFN: Cell Frame Number
The Physical Layer – Rel 99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
37/85
37 © Nokia Siemens Networks RN31552EN30GLA0
The Physical Layer – Rel. 99
• Channel Mapping
• Transport Channel Formats
• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel Downlink
• Dedicated Physical Channel Uplink
Secondary Common Control Physical Channel (S-CCPCH) (1/6)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
38/85
38 © Nokia Siemens Networks RN31552EN30GLA0
Slot 0 Slot 1 Slot 2 Slot 14
10 ms Frame
S-CCPCH
TFCI
(optional)Data Pilot bits
• carries PCH and FACH
• Multiplexing of PCH and FACH on one
S-CCPCH, even one frame possible
• with and without TFCI (UTRAN set)
• SF = 4..256• (18 different slot formats
• no inner loop power control
Secondary Common Control Physical Channel (S CCPCH) (1/6)
S-CCPCH (2/6): Number of S-CCPCHs
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
39/85
39 © Nokia Siemens Networks RN31552EN30GLA0
S CCPCH (2/6): Number of S CCPCHs
• The S-CCPCH (Secondary Common Control Physical Channel) carries FACH & PCH
transport channels
• Parameter WCEL: NbrOfSCCPCHs (Number of SCCPCHs) tells how many SCCPCHswill be configured for the cell. (1, 2 or 3)
• If only 1 SCCPCH is used in a cell, it will carry FACH-c (containing DCCH/CCCH /BCCH),
FACH-u (containing DTCH) and PCH. FACH and PCH multiplexed onto the same SCCPCH.
• If 2 SCCPCHs are used in a cell, the first SCCPCH will carry FACH-u & FACH-c and the second
SCCPCH will always carry PCH only.
• If 3 SCCPCHs are used in a cell, the third SCCPCH will carry FACH-s (containing CTCH) &FACH-c idle (containing CCCH & BCCH). The third SCCPCH is only needed when Service Area
Broadcast (SAB) is active in a cell.
NbrOfSCCPCHs
WCEL; 1..3; 1; 1
S-CCPCH (3/6): Configuration 1
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
40/85
40 © Nokia Siemens Networks RN31552EN30GLA0
S CCPCH (3/6): Configuration 1
• If only 1 SCCPCH is used in a cell, it will carry FACH-c (containing DCCH/CCCH /BCCH), FACH-u
(containing DTCH) and PCH. FACH and PCH multiplexed onto the same SCCPCH.
• the PCH bit rate is limited to 8 kbps
• the PCH always has priority
• the SF for SCCPCH, which is carrying FACH (with or without PCH), is 64 (60ksps)
Logical channel
Transport channel
Physical channel
DTCH DCCH CCCH BCCH PCCH
FACH-u FACH-c PCH
SCCPCH 1
SF 64
PtxSCCPCH1 Transmission Power of SCCPCH1WCEL; -35..15; 0.1; 0 dB
S-CCPCH (4/6): Configuration 2 a & b
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
41/85
41 © Nokia Siemens Networks RN31552EN30GLA0
S CCPCH (4/6): Configuration 2 a & b
• If 2 SCCPCHs are used in a cell, the first SCCPCH will carry FACH-u & FACH-c and the second
SCCPCH will always carry PCH only.
• PCH bit rate limited to 8 kbps (RU10 & earlier) or can be extended
to 24 kbps (RU20: 24 kbps Paging Channel)
• if PCH24kbps enabled, NbrOfSCCPCHs must be set to “2” or “3”
Logical
channel
Transport
channel
Physical
channel
DTCH DCCH CCCH BCCH PCCH
FACH-u FACH-c PCH
SCCPCH 1 SCCPCH 2
SF 64 SF 256
PCH24kbpsEnabled
WCEL; 0 (Disabled), 1 (Enabled);default: 0 (Disabled)
SF 128or
PtxSCCPCH2used for 8 kbps paging
WCEL; -35..15; 0.1; -5 dB
PtxSCCPCH2SF128used for 24 kbps paging
WCEL; -35..15; 0.1; -2 dB
S-CCPCH (5/6): Configuration 3a & b
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
42/85
42 © Nokia Siemens Networks RN31552EN30GLA0
Logical channel
Transportchannel
Physicalchannel
DTCH DCCH CCCH BCCH CTCH
FACH-u PCHFACH-s
SCCPCHconnected
SCCPCHidle
PCCH
FACH-c FACH-c
SCCPCHpage
For SAB
( ) g
• if 3 SCCPCHs are used in a cell, the third SCCPCH will carry FACH-s (containing CTCH) & FACH-c
idle (containing CCCH & BCCH). The third SCCPCH is only needed when Service Area Broadcast
(SAB) is active in a cell.
SF 64 SF 128 SF 256
SF 128orPtxSCCPCH3
WCEL; -35..15; 0.1; -2 dB
S-CCPCH (6/6) in NSN RAN
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
43/85
43 © Nokia Siemens Networks RN31552EN30GLA0
FACH-uFACH-c
(connected)FACH-c
(idle)
TFS
TTI
Channelcoding
CRC
0: 0x360 bits
(0 kbit/s)
1: 1x360 bits
(36 kbit/s)
10 ms
TC 1/3
16 bit
0: 0x168 bits
(0 kbit/s)
1: 1x168 bits
(16.8 kbit/s)
2: 2x168 bits
(33.6 kbit/s)
10 ms
CC 1/2
16 bit
0: 0x168 bits
(0 kbit/s)
1: 1x168 bits
(16.8 kbit/s)
10 ms
CC 1/3
16 bit
FACH-s
0: 0x168 bits
(0 kbit/s)
1: 1x168 bits
(16.8 kbit/s)
10 ms
CC 1/3
16 bit
PCH
0: 0x80 bits
(0 kbit/s)
1: 1x80 bits
(8 kbit/s)
2: 1x240 bits
(24 kbps)
10 ms
CC 1/2
16 bit
( )
The Paging Process
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
44/85
44 © Nokia Siemens Networks RN31552EN30GLA0
Paging Indicator Channel (PICH)
• UMTS provides the terminals with an efficient sleep mode operation. The UEs do not have to read and
process the content, transmitted during their paging occasion on their S-CCPCH.
• Each S-CCPCH, which is used for paging, has an associated Paging Indicator Channel (PICH).
• A PICH is a physical channel, which carries paging indicators.• A set of (paging indicator) bits within the PICH indicate to a UE, whether there is a paging occasion for
it. Only then, the UE listens to the S-CCPCH frame, which is transmitted 7680 chips after the PICH
frame in order to see, whether there is indeed a paging message for it.
• The PICH is used with spreading factor 256.
• 300 bits are transmitted in a 10 ms frame, and 288 of them are used for paging indication.
• The UE was informed by the BCCH, how many paging indicators exist on a 10 ms frame.
• The number of paging indicator Np can be 18, 36, 72, and 144, and is set by the operator as part of the networkplanning process.
• The higher Np, the more paging indicators exist, the more paging groups exist, among which UEs can bedistributed on.
• Consequently, the lower the probability, that a UE reacts on a paging indicator, while there is no paging message
in the associated S-CCPCH frame.
• But a high number of paging indicators results in a comparatively high output power for the PICH, because less
bits exists within a paging indicator to indicate the paging event.
• The operator then also has to consider, if he has to increase the number of paging attempts.
• How does the UE and UTRAN determine the paging indicator (PI) and the Paging Occasion?
• This is shown in one of the next slides.
g g
S-CCPCH & associated PICH
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
45/85
45 © Nokia Siemens Networks RN31552EN30GLA0
PICH frame
S-CCPCH frame,
associated with PICH frame
PICH
= 7680chips
b287 b288 b299b286b0 b1
for paging indication no transmission
# of paging
indicators per frame
(Np)
18
36
72
144
S-CCPCH
Np Repetition of PICH bits18, 36, 72 144
PtxPICH -10..5; 1; -8 dB
Paging & Discontinuous Reception (FDD mode)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
46/85
46 © Nokia Siemens Networks RN31552EN30GLA0
2k frames
k = 3..9
Duration:
CN domain specific
DRX cycle lengths
(option)
UE
CS Domain PS Domain
Update:
a) derived by NAS
negotiation
b) otherwise:
system info
Update:
locally with
system info
k 1 k 2
UTRAN
Update:
a) derived by NAS
negotiation
b) otherwise:
system info
k 3
RRC connected
mode
stores
if RRC idle:
UE DRX cycle length is
min (k 1, k 2)
if RRC connected:
UE DRX cycle length is
min (k 3, k domain with no Iu-signalling connection)
Example with
two CN domains
UTRAN_DRX_length 80; 160; 320; 640; 1280;
2560; 5120 ms
CNDRXLength 640; 1280; 2560; 5120 ms
Paging Indicator & Paging Occasion (FDD mode)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
47/85
47 © Nokia Siemens Networks RN31552EN30GLA0
UE
my paging
indicator (PI)
PI = ( IMSI div 8192) mod Np
DRX index
number of paging indicators
18, 36, 72, 144
Paging Occasion = (IMSI div K) mod (DRX cycle length)
+ n * DRX cycle length
UE
When willI get paged?
number of S-CCPCH with PCH
FDD
mode
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
48/85
Example – Paging instant & group calculation
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
49/85
49 © Nokia Siemens Networks RN31552EN30GLA0
K (Number of S-CCPCH with PCH) 1
k (DRX length) 6
DRX cycle length 64 framesIMSI 358506452377
Which S-CCPCH #? 0
IMSI div K 358506452377
When (Paging occation, SFN)? 25 + n*DRX cycle length
Np 72 PIs/frame
DRX Index 43762994
My PI? 26
Number of subsc. In LA/RA 100000
Number of subsc. Per S-CCPCH 100000
Number of subsc. Paging occation (PICHframe) 1562.5
Number of subsc. Per PI 21.7
The Physical Layer – Rel. 99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
50/85
50 © Nokia Siemens Networks RN31552EN30GLA0
• Channel Mapping
• Transport Channel Formats
• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel Downlink
• Dedicated Physical Channel Uplink
Random Access
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
51/85
51 © Nokia Siemens Networks RN31552EN30GLA0
In the random access, initiated by the UE, two physical channels are involved:
Physical Random Access Channel (PRACH)
• The physical random access is decomposed into the transmission of preambles in the UL.
• Each preamble is transmitted with a higher output power as the preceding one.• After the transmission of a preamble, the UE waits for a response by the Node B.
• This response is sent with the physical channel Acquisition Indication Channel (AICH), telling
the UE, that the Node B as acquired the preamble transmission of the random access.
• Thereafter, the UE sends the message itself, which is the RACH/CCCH of the higher layers.
• The preambles are used to allow the UE to start the access with a very low output power.
• If it had started with a too high transmission output power, it would have caused interference
to the ongoing transmissions in the serving and neighbouring cells.• Please note, that the PRACH is not only used to establish a signalling connection to UTRAN, it
can be also used to transmit very small amounts of user data.
Acquisition Indication Channel (AICH)
• This physical channel indicates to the UE, that it has received the PRACH preamble and is now
waiting for the PRACH message part.
Random Access – the Working Principle
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
52/85
52 © Nokia Siemens Networks RN31552EN30GLA0
UE
No response
by the
Node B
No response
by the
Node B
I just detected
a PRACH preamble
OLA!
Node B
Random Access Timing
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
53/85
53 © Nokia Siemens Networks RN31552EN30GLA0
• The properties of the PRACH are broadcasted (SIB5, SIB6).
• The candidate PRACH is randomly selected (if there are several PRACH advertised in the cell) as well
as the access slots within the PRACH.
• 15 access slots are given in a PRACH, each access slot lasting two timeslots or 5120 chips.
• In other words, the access slots stretch over two 10 ms frames.• A PRACH preamble, which is transmitted in an access slot, has a length of 4096 chips.
• Also the AICH is organised in (AICH) access slots, which stretch over two timeslots.
• AICH access slots are time aligned with the P-CCPCH.
• The UE sends one preamble in UL access slot n.
• It expects to receive a response from the Node B in the DL (AICH) access slot n,p-a chips later on.
• If there is no response, the UE sends the next preamble p-p chips after the first one.• The maximum numbers of preambles in one preamble access attempt can be set between 1 and 64.
• The number of PRACH preamble cycles can be set between 1 and 32.
• If the AICH_Transmission_Timing parameter in the SIB is set to BCCH SIB5 & SIB6 to
• 0 = then, the minimum preamble-to-preamble distance is 6 access slots, the minimum
preamble-to-message distance is 6 access slots, and the preamble-to-acquisition indication
is 3 timeslots.
• 1 = then, the minimum preamble-to-preamble distance is 8 access slots, the minimumpreamble-to-message distance is 8 access slots, and the preamble-to-acquisition indication
is 4 timeslots.
Random Access Timing
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
54/85
54 © Nokia Siemens Networks RN31552EN30GLA0
SFN mod 2 = 0 SFN mod 2 = 0SFN mod 2 = 1
P-CCPCH
AICH access
slots 0 1 1282 1175 964 13103 14 0 1 2 75 643
5120
chips
Preamble
5120 chips
Preamble
AS # i
4096 chips
preamble-to-preamble
distancep-p
UE point of view
PRACH
access slots
AICH
access slots
Message
part
preamble-to-message
distance p-m
Acquisition
Indication
preamble-to-AI
distancep-a
AS # i
TS 25.211:
Preamble-to-Preamble distance p-p p-p,min = 6 / 8 Slots
Preamble-to-AI distance p-a = 3 / 4 Slots
Preamble-to-Message distance p-m = 6 / 8 Slots
Broadcasted by P-CCPCH;
NSN (WCEL):
AICHTraTime = 0, 1; 0
I th PRACH bl d bl d i d
PRACH Preamble
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
55/85
55 © Nokia Siemens Networks RN31552EN30GLA0
• In the PRACH preamble, a random preamble code is used.
• This code is composed from a
• Preamble Scrambling Code and a
• Preamble Signature
• There is a total of 16 preamble signatures of 16 bit length, which is repeated 256 times within one
preamble.
• When monitoring the cell system information, the UE gets the information, which of the signatures are
available for use in the cell. (see IE PRACH info)
• There are 8192 preamble scrambling codes, which are constructed from the long scrambling code
sequences.• The PRACH preamble scrambling codes are organised in 512 groups, with each group holding 16
members.
• There are also 512 primary scrambling codes available in UMTS, and one of them is in use in the cell.
• If the primary scrambling code s is in use in the cell, then only the PRACH preamble scrambling codes
belonging to PRACH preamble scrambling code group s can be used for random access.
• Consequently, 16 PRACH preamble scrambling codes are left, and the BCCH is used to inform the
UE, which PRACH preamble scrambling codes can be used. (see IE PRACH info)
UTRAN
PRACH Preamble
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
56/85
56 © Nokia Siemens Networks RN31552EN30GLA0
Node B
UTRANBCCH
UE RNC
Pi Pi Pi Pi
Preamble Signature
(16 different versions)
16 chip
256 repetitions
PRACH Preamble Scrambling Code
• 512 groups, each with 16
preamble scrambling codes• Cell‘s primary scrambling codes
associated with preamble
scrambling code group
• available signatures forrandom access
• available preamble
scrambling codes
• available spreading
factor
• available sub-channels
• etc.
AllowedPreamble
Signatures
WCEL; 16-bit field;
0….01111; max. 4
signatures allowed
Th l th f th PRACH t b 10 20
PRACH Message Part
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
57/85
57 © Nokia Siemens Networks RN31552EN30GLA0
• The length of the PRACH message part can be 10 ms or 20 ms.
• Its length is set as Transmission Time Interval (TTI) value by the higher layers.
• UL, we apply code multiplexing.
• L1 Control data are transmitted with SF 256, while message data can be transmitted with SF 256,
128, 64 or 32.• The message data contains the information, given by the RACH.
• The control data contains 8 known pilot bits / slot. 15 different pilot bit sequences exist – they are
associated with the slot, where the transmission takes place within the 10 ms message frame. 2 bits in
the control data carry TFCI bits / slot.
• Which spreading code is allocated to the message part?
• The message part‘s channelisation code is determined from the signature, which was used by the UEin the preamble.
• 16 different signatures exist, and each can be correlated to a channelisation code in the
channelisation code tree with spreading factor 16.
• The channelisation codes are calculated like this:
• Each signature has a number k, with 0 k 15.
• For the control data, the channelisation code CCH,256,n is used, with n = 16*k + 15.
• For the message data, the channelisation code CCH,SF,m is used, with m = SF*k/16.• The scrambling code is the same, which was used for the PRACH preamble.
10 ms Frame
PRACH Message Part
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
58/85
58 © Nokia Siemens Networks RN31552EN30GLA0
Slot 0 Slot 1 Slot 2 Slot 14
10 ms Frame
RACH data
L1 control data 8 Pilot bits (sequence depends on slot number) 2 TFCI bits
data
• SF = 256
• channelisation code:CCH,256,16*k+15, with
k = signature number
• SF = 256, 128, 64, or 32
• channelisation code:
• CCH,SF,SF*k/16, with
k = signature number
Scrambling code =
PRACH preamble scrambling code
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
59/85
Preamble_Initial_Power =
Primary CPICH TX power
PRACH Power Setting
PRACHRequiredReceivedCI
WCEL: 35 10; 1; 25 dB
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
60/85
60 © Nokia Siemens Networks RN31552EN30GLA0
Primary CPICH TX power
– CPICH_RSCP
+ UL interference
+ Required received C/I
Downlink / BS
Preamble 1 Message part
…. ….
Preamble n
PRACH_preamble_retrans:
The maximum number of preambles
allowed in 1 preamble ramping cycle
RACH_tx_Max : # of preamble powerramping cycles that can be done
before RACH transmission failure isreported,
UEtxPowerMaxPRACH
WCEL: -50..33; 1; 21 dBm
PRACH_preamble_retrans
WCEL: 1..64; 1; 8
PowerRampStep
PRACHpreamble
WCEL: 1..8; 1; 2 dB
Uplink / UE
PowerOffset
LastPreamble
PRACHmessage
WCEL:
-5..10; 1; 2 dB
RACH_tx_Max
WCEL: 1..32; 1; 8
(Range, Steps; Default)
WCEL: -35..-10; 1; -25 dB
• The AICH is used to indicate to UEs that their PRACH preamble was received and that the Node B is
Acquisition Indication Channel (AICH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
61/85
61 © Nokia Siemens Networks RN31552EN30GLA0
• The AICH is used to indicate to UEs, that their PRACH preamble was received, and that the Node B is
expecting to receive the PRACH message part next.
• The AICH returns an indicator of signature s, which was used in the PRACH preamble.
• Spreading factor is fixed to 256 for the AICH.
• The AICH is transmitted via 15 access slots, each lasting 5120 chips.• Consequently, the AICH access slots are distributed over two consecutive 10 ms frames.
• Similar to the PRACH preamble, only 4096 chips are used to transmit the Acquisition Indicator part.
• 32 real value symbols are transmitted.
• Each real value is calculated by a sum of AIsbs,j.
• AI is an acquisition indicator for signature s.
• If signature s is positively confirmed, Ais is set to +1; a negative confirmation results in –1; if
signature s is not part of the active signature set, then Ais is set to 0. bs,j stands for signaturepattern j, with j = 0..31.
• If more than one PRACH preamble signatures within one PRACH access slot is detected correctly,
the Node B sends the AIs of all the detected signatures simultaneously in the 1st or 2nd AICH
access slot after the PRACH access slot.
• If the number of correctly detected signatures is higher than the Node B's capability to
simultaneously decode the PRACH message parts, a negative AIs is used for generating the AIs
for those PRACH messages, which can not be decoded within the default message parttransmission timing.
• A negative AI indicates to the MS that it shall exit the random access procedure.• The Node B 's capability to decode the PRACH message parts is determined in the RNC and
transmitted to the Node B.
20 ms Frame
Acquisition Indication Channel (AICH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
62/85
62 © Nokia Siemens Networks RN31552EN30GLA0
Access Slot 0 Access Slot 1 Access Slot 2 Access Slot 14
20 ms Frame
a0 a1 a2 a29 a30 a31
15
0
js,s j bAIa s
AICH signature pattern (fixed)
Acquisition Indicator
• +1 if signature s is positively confirmed
• -1 if signature s is negatively confirmed• 0 if signature s is not included in the
set of available signatures
PtxAICH
-22..5; 1; -8 dB
Summary of RACH procedure (Adopted from TS 25.214)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
63/85
63 © Nokia Siemens Networks RN31552EN30GLA0
1- Decode from BCCH
• Available RACH spreading factors
• RACH scrambling code number
• UE Access Service Class (ASC) info• Signatures and sub-channels for each ASC
• Power step, RACH C/I requirement = “Constant”, BS interference level
2 – Calculate initial preamble power
3 – Calculate available access slots in the next full access slot set and select randomly one of those
4 – Select randomly one of the available signatures
5 – Transmit preamble in the selected access slot with selected signature
6 – Monitor AICH• IF no AICH
• Increase the preamble power
• Select next available access slot & Go to 3
• IF negative AICH or max. number of preambles exceeded
• Exit RACH procedure
• IF positive AICH
• Transmit RACH message with same scrambling code and channelisation code related to signature
The Physical Layer – Rel. 99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
64/85
64 © Nokia Siemens Networks RN31552EN30GLA0
• Channel Mapping
• Transport Channel Formats
• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel - Downlink
• Dedicated Physical Channel - Uplink
• The DL DPCH is used to transmit the DCH data.
DL Dedicated Physical Channel (DPCH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
65/85
65 © Nokia Siemens Networks RN31552EN30GLA0
• Control information and user data are time multiplexed.
• The control data is associated with the Dedicated Physical Control Channel (DPCCH), while the user
data is associated with the Dedicated Physical Data Channel (DPDCH).
• The transmission is organised in 10 ms radio frames, which are divided into 15 timeslots.• The timeslot length is 2560 chips. Within each timeslot, following fields can be found:
• Data field 1 and data field 2, which carry DPDCH information
• Transmission Power Control (TPC) bit field
• Transport Format Combination Indicator (TFCI) field, which is optional
• Pilot bits
• The exact length of the fields depends on the slot format, which is determined by higher layers.
• The TFCI is optional, because it is not required for services with fixed data rates.• Slot format are also defined for the compressed mode; hereby different slot formats are in used, when
compression is achieved by a changed spreading factor or a changed puncturing scheme.
• The pilot sequence is used for channel estimation as well as for the SIR ratio determination within the
inner loop power control.
• The number of the pilot bits can be 2, 4, 8 and 16 – it is adjusted with the spreading factor.
• A similar adjustment is done for the TPC value; its bit numbers range between 2, 4 and 8.
• The spreading factor for a DPCH can range between 4 and 512. The spreading factor can be changed
every TTI period.
• Superframes last 720 ms and were introduced for GSM-UMTS handover support.
Superframe = 720 ms
DL Dedicated Physical Channel (DPCH)
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
66/85
66 © Nokia Siemens Networks RN31552EN30GLA0
Slot 0 Slot 1 Slot 2 Slot 14
10 ms Frame
TPC
bitsPilot bits
TFCI
bits(optional)
Data 2 bitsData 1 bits
DPDCHDPDCH DPCCH DPCCH
Radio Frame
0
Radio Frame
1
Radio Frame
2
Radio Frame
71
p
• 17 different slot formats
• Compressed mode slot
format for changed SF &
changed puncturing
• Power offsets for the optional TFCI, TPC and pilot bits have to be specified during the radio link setup.
Power Offsets for the DPCH
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
67/85
67 © Nokia Siemens Networks RN31552EN30GLA0
• This is done with the NBAP message RADIO LINK SETUP REQUEST message, where following
parameters are set:
• PO1: defines the power offset for the TFCI bits; it ranges between 0 and 6 dB with a 0.25
step size.
• PO2: defines the power offset for the TPC bits; it ranges between 0 and 6 dB with a 0.25
step size.
• PO3: defines the power offset for the pilot bits; it ranges between 0 and 6 dB with a 0.25
step size.
• In the same message, the TFCS, DL DPCH slot format, multiplexing position, FDD TPC DL
step size increase, etc. are defined.
• The FDD TPC DL step size is used for the DL inner loop power control.
• Power offsets
• TFCS
• DL DPCH slot format
• FDD DL TPC step
Power Offsets for the DPCH
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
68/85
68 © Nokia Siemens Networks RN31552EN30GLA0
Node B RNC
DCH Data Frame
Iub
UE
Uu
PO1
NBAP: RADIO LINK SETUP REQUEST
TPC
bitsPilot bits
TFCI
bits(optional) Data 2 bitsData 1 bits
PO3PO2
• FDD DL TPC step
size
• ...
P0x: 0..6 dB
step size: 0.25 dB
• Inner loop power control is also often called (fast) closed loop power control.
It t k l b t th UE d th N d B
DL Inner Loop Power Control
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
69/85
69 © Nokia Siemens Networks RN31552EN30GLA0
• It takes place between the UE and the Node B.
• We talk about UL inner loop power control, when the Node B returns immediately after the reception of
a UE‘s signal a power control command to the UE. By doing so, the UE‘s SIR ratio is kept at a certain
level (the details will be discussed later on in the course).• DL inner loop power control control is more complex. When the UE receives the transmission of the
Node B, the UE returns immediately a transmission power control command to the Node B, telling the
Node B either to increase or decrease its output power for the UE‘s DPCH.
• The Node B‘s transmission power can be changed by 0.5, 1, 1.5 or 2 dB. 1 dB must be supported by
the equipment. If other step sizes are supported or selected, depends on manufacturer or operator.
• The transmission output power for a DPCH has to be balanced for the PICH, which adds to the power
step size.• There are 2 DL inner loop power control modes:
• DPC_MODE = 0: Each timeslot, a unique TPC command is send UL.
• DPC_MODE = 1: 3 consecutive timeslots, the same TPC command is transmitted.
• One reason for the UE to request higher output power is the case that the QoS target is not met.
• It requests the Node B to transmit with a higher output power, hoping to increase the quality
of the connection due to an increased SIR at the UE‘s receiver.
• But this also increases the interference level for other phones in the cell and neighbouring
cells.
• The operator can decide, whether to set the parameter Limited Power Increase Used .
• If used, the operator can limit the output power raise within a time period.
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
70/85
DL Inner Loop PC: UTRAN behaviour
UE WCDMA BTS • Receiving the TPC commands BS adjusts the DL
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
71/85
71 © Nokia Siemens Networks RN31552EN30GLA0
Measured SIR < SIR target --> TPC command is "1"
Measured SIR => SIR target --> TPC command is "0"
Compare measured SIR with SIR target
value received from DL outer loop PC
Measure received SIR on DL DPCCH
WCDMA BTS
BS sets the power on DL DPCCH and DL DPDCH following way:
TPC command = "1" --> increase power by 1 dB
TPC command = "0" --> decrease power by 1 dB
DL DPCCH + DPDCHs
Send TPC command on UL DPCCH
Changed power on DL DPCCH + DPDCHs
Receiving the TPC commands BS adjusts the DL
DPCCH/DPDCH power
• UTRAN shall estimate the transmitted TPC command
TPCest to be 0 or 1; it shall update the power every slot.
• After estimating the k :th TPC command, UTRAN
shall adjust the current DL power P (k -1) [dB] to a
new power P (k ) [dB]:
P (k ) = P (k - 1) + P TPC (k )
where P TPC (k ) is the k :th power adjustment due to the
inner loop power control
DownlinkInnerLoopPCStepSize
DownlinkInnerLoop
PCStepSize
RNC: 0.5..2; 0.5; 1 dB
The Physical Layer – Rel. 99
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
72/85
72 © Nokia Siemens Networks RN31552EN30GLA0
• Channel Mapping
• Transport Channel Formats
• Cell Synchronisation
• Common Control Physical Channels
• Physical Random Access
• Dedicated Physical Channel - Downlink
• Dedicated Physical Channel - Uplink
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
73/85
Superframe = 720 ms
UL Dedicated Physical Channels
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
74/85
74 © Nokia Siemens Networks RN31552EN30GLA0
Slot 0 Slot 1 Slot 2 Slot 14
10 ms Frame
TPC
bitsPilot bits
TFCI bits(optional)
Data 1 bits
Radio Frame
0
Radio Frame
1
Radio Frame
2
Radio Frame
71
DPDCHSF = 256 - 4
DPCCHSF 256
FBI bits(optional)
• 7 different
slot formats
• 6 different slot formats
• Compressed mode slot
format for changed SF &changed puncturing
Feedback Indicator for• Closed loop mode transmit diversity, &
• Site selection diversity transmission (SSDT)
• Discontinuous transmission (DTX) is supported for the DCH both UL & DL.
• If DTX is applied in the DL – as it is done with speech – then 3000 bursts are generated in one
Discontinuous Transmission & Power Offsets
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
75/85
75 © Nokia Siemens Networks RN31552EN30GLA0
• If DTX is applied in the DL – as it is done with speech – then 3000 bursts are generated in one
second. (1500 times the pilot sequence, 1500 times the TPC bits)
• This causes two problems:
• Inter-frequency interference, caused by the burst generation.• At the Node B, the problem can be overcome with exquisite filter equipment. This filter
equipment is expensive and heavy. Therefore it cannot be applied in the UE.
• The UE‘s solution is I/Q code multiplexing, with a continuous transmission for the DPCCH.
DPDCH changes can still occur, but they are limited to the TTI period. The minimum TTI
period is 10 ms. The same effects can be observed, then the DPDCH data rate and with it its
output power is changing.
• 3000 bursts causes audible interference with other equipment – just see for example GSM.• By reducing the changes to the TTI period, the audible interference is reduced, too.
• Determination of the power difference between the DPCCH and DPDCH
• I/Q code multiplexing is done in the UL, i.e. the DPCCH and DPDCH are transmitted with different
codes (and possible with different spreading factors). Gain factors are specified:c is the gain
factor for the DPCCH, whiled is the gain factor for the DPDCH. The gain factors may vary for
each TFC. There are two ways, how the UE may learn about the gain factors:
• The gain factors are signalled for each TFC. If so, the nominal power relation Aj between
the DPDCH and DPCCH isd/c.
• The gain factor is calculated based on reference TFCs. (The details for gain factor calculation
based on reference TFCs are not discussed in this course.)
Discontinuous Transmission and Power Offsets
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
76/85
76 © Nokia Siemens Networks RN31552EN30GLA0
DPCCH
DPDCH
DPCCH
DPDCH
DPCCH
DPDCH
TTI TTI TTI
UL DPDCH/DPCH Power Difference:
DPCCH
DPDCH
=d
c
=Nominal Power Relation Aj
two methods to determine the gain factors:
• signalled for each TFCs
• calculation based on reference TFCs
• The subscriber is mobile. The distance of the UE from a Node B is changing over time.
• With growing distance and a fixed output power at the UE the received signals at the Node B
UL Inner Loop Power Control
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
77/85
77 © Nokia Siemens Networks RN31552EN30GLA0
With growing distance and a fixed output power at the UE, the received signals at the Node B
become weaker.
• UE output power adjustment is required.
• But the UE‘s received signal strength can change fast – Rayleigh fading in one phenomena,which causes this event.
• As a consequence, a fast UL power control is required.
• This power control is called UL inner loop power control, though many experts also call it (fast)
closed loop power control.
• At each active set cell, a target SIR (SIRtarget) is set for each UE. The active set cells estimate SIRest
on the UE‘s receiving UL DPCH. Each active set cell determines the TPC value. If the estimated SIR
is larger than the UE‘s target SIR, then the determined TPC value is 0. Otherwise it is 1. These
values are determined on timeslot basis and returned on timeslot basis.
• The UE has to determine the power control command (TPC_cmd). The higher layer control
protocol RRC is used to inform the UE, which power control algorithm to apply. This informs the UE
also how to generate a power control command from the incoming TPC-values.
There are power control algorithm 1 (PCA1) and 2 (PCA2), which are described in the figure
following the next one. Given the power control algorithm and the TPC-values, the UE determines,
how to modify the transmit power for the DPCCH: DPCCH = TPC TPC_cmd. TPC stands for the
transmission power step size.
(continued on the next text slide)
SIR
UL Inner Loop Power Control
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
78/85
78 © Nokia Siemens Networks RN31552EN30GLA0
time
SIRest
SIRtarget
TPC
TPC_cmd
in FDD mode:1500 times per second
Power Control Algorithm 1
• is applied in medium speed environments.
UL Inner Loop Power Control
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
79/85
79 © Nokia Siemens Networks RN31552EN30GLA0
is applied in medium speed environments.
• Here, the UE is commanded to modify its transmit power every timeslot.
• If the received TPC value is 1, the UE increases the transmission output at the DPCCH by
DPCCH, otherwise it decreases it by DPCCH.• The DPCCH is either 1 or 2 dB, as set by the higher layer protocols.
• TPC values from the same radio link set represent one TLC_cmd.
• TPC_cmds from different radio link sets have to be weighted, if there is no reliable
interpretation.
Power Control Algorithm 2
• was specified to allow smaller step sizes in the power control in comparison to PCA1.• This is necessary in very low and high speed environments.
• In these environments, PCA1 may result in oscillating around the target SIR.
• PCA2 changes only with every 5th timeslot, i.e. the TPC_cmd is set to 0 the first 4 timeslots.
In timeslot 5, the TPC_cmd is –1, 0, or 1.
• For each radio set, the TPC_cmd is temporarily determined. This can be seen in the next
figure.
• The temporary transmission power commands (TPC_temp) are combined as can be seen in
the figure after the next one. Here you can see, how the final TPC_cmd is determined.
NSN supports only PCA 1.
algorithms for processing power
control commands TPC cmd
UL Inner Loop Power Control
NSN supports only
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
80/85
80 © Nokia Siemens Networks RN31552EN30GLA0
PCA2 PCA1 PCA2
control commands TPC_cmd
PCA1
TPC_cmd for each TS
TPC_cmd values: +1, -1
step size TPC: 1dB or 2dB
PCA2
TPC_cmd for 5th TS
TPC_cmd values: +1, 0, -1
step size TPC: 1dB
UL DPCCH power adjustment: DPCCH = TPC TPC_cmd
km/h0
3
80Rayleigh fading can be compensated
PCA 1 with step size 1 dB
Example: reliable transmission
Power Control Algorithm 1
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
81/85
81 © Nokia Siemens Networks RN31552EN30GLA0
p
Cell 1Cell 2
Cell 3
TPC1 = 1 TPC3 = 0
TPC3 = 1
TPC_cmd = -1
(Down)
NSN: only PCA 1 is supported.
TPC t
Power Control Algorithm 2
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
82/85
82 © Nokia Siemens Networks RN31552EN30GLA0
TPC_temp
0
00
0
1
0
0
0
0
0
0
0
0
0
-1
• if all TPC-values = 1
TPC_temp = +1
• if all TPC-values = 0
TPC_temp = -1
• otherwise
TPC_temp = 0
NSN: PCA 2 is not supported.
• UTRAN shall start the transmission of the DL DPCCH and may start the transmission of DPDCH if any
data is to be transmitted.
Initial UL DCH Transmission
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
83/85
83 © Nokia Siemens Networks RN31552EN30GLA0
• The UE UL DPCCH transmission shall start
• When higher layers consider the DL physical channel established, if no activation time for UL
DPCCH has been signalled to UE• If an activation time has been given, UL DPCCH transmission shall not start before the DL
physical channel has been established and the activation time has been reached.
• When we look to the PRACH, we can see, that preambles were used to avoid UEs to access UTRAN
with a too high initial transmission power.
• The same principle is applied for the DPCH.
• The UE transmits between 0 to 7 radio frames only the DPCCH UL, before the DPDCH is code
multiplexed.
• The number of radio frames is set by the higher layers (RRC resp. the operator).
• Also for this period of time, only DPCCH can be found in the DL.
• The UE can be also informed about a delay regarding RRC signalling – this is called SRB delay,
which can also last 0 to 7 radio frames. The SRB delay follows after the DPCCH preamble.
• How to set the transmission power of the first UL DPCCH preamble?
• Its power level is
• DPCCH_Initial_power = – CPICH_RSCP + DPCCH_Power_offset• The DPCCH Power Offset is retrieved from RRC messages. It’s value ranges between –164
and –6 dB (step size 2 dB). CPICH_RSCP is the received signal code power on the P-
CPICH, measured by the UE.
DPCCH only DPCCH & DPDCH
Initial UL DCH Transmission
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
84/85
84 © Nokia Siemens Networks RN31552EN30GLA0
reception
at UE
trans-mission
at UE
DPCCH only DPCCH & DPDCH
0 to 7 frames for
power control preamble
DPCCH_Initial_power = – CPICH_RSCP + DPCCH_Power_offset
DL Synch &Activation time
0 to 7 frames of
SRB delay
PCPreamble
RNC: 0..7; 1; 0
SRBDelay
RNC: 0..7; 1; 7
For this course module, following 3GPP specifications were used:
References
-
8/19/2019 02 RN31552EN30GLA0 the Physical Layer Rel99
85/85
85 © Nokia Siemens Networks RN31552EN30GLA0
• TS 25.211 V6, Physical channels & mapping of transport channels onto physical channels
• TS 25.212 V6, Multiplexing and channel coding (FDD)
• TS 25.213 V6, Spreading and modulation (FDD)• TS 25.214 V6, Physical layer procedures (FDD)
• TS 25.215 V6, Physical layer; Measurements (FDD)
• TS 25.301 V6, Radio interface protocol architecture
• TS 25.302 V6, Services provided by the physical layer
• TS 25.306 V5 – V8: UE Radio Access capabilities
• TS 25.321 V6, Medium Access Control (MAC) protocol specification• TS 25.331 V6, Radio Resource Control (RRC) protocol specification
• TS 25.402 V6, Synchronization in UTRAN Stage 2
• TS 25.433 V6, UTRAN Iub interface Node B Application Part (NBAP) signalling
NSN WCDMA Product documentation