15

DK Cable Junction Boxes

DK Cable Junction Boxes- 1.5 up to 240 mm

- Degree of protection IP 54-67

- Cable Junction Boxes are VDE tested in accordance with IEC 60670-22

i

Assembling videos

16

DK Cable Junction Boxes Content

Criteria for selecting 18 - 19Box walls 20

Box walls without knockoutsfrom 1.5 up to 50 mm2

IP 65box walls without knockouts, can be drilled individually for customized requirements- without terminals 33 - 34- without terminals, for electrical equipment up to 63 A 35 - 36- Accessories 37 - 39

With or without terminalsfrom 1.5 up to 240 mm2

IP 65/IP 55cable entry via metric knockouts- with terminals for copper conductors 24 - 29- without terminals 30 - 31

With FIXCONNECT plug-in technology for copper conductorsfrom 1.5 up to 16 mm2

IP 65/IP 55cable entry via metric knockouts 22

For aluminium- (Alu) and copper (Cu) conductorsfrom 1.5 up to 240 mm2

IP 65/55cable entry via metric knockouts- with terminal blocks for aluminium- (Alu) and copper (Cu) conductors 54 - 60

Cable entry via elastic membranes and integrated M20 threadup to 4 mm2

IP 55- without terminals 41- with terminals for copper conductors 41

Cable entry via cable, cable trunking and conduitsfrom 1.5 up to 4 mm2

IP 54- with terminals for copper conductors 43 - without terminals, Accessories 44

Cable entry via elastic membranesfrom 1.5 up to 4 mm2

IP 55- with terminals for copper conductors, grey RAL 7035 46- without terminals, grey RAL 7035 47- with terminals for copper conductors, white RAL 9016 48- without terminals, white RAL 9016, Accessories 49

Cable entry via elastic membranes from the rear and by box walls and lidfrom 1.5 up to 2.5 mm2

IP 55for the clip-on attachment- with terminals for copper conductors, grey RAL 7035 51- without terminals, grey RAL 7035 51- with terminals for copper conductors, white RAL 9016 52- without terminals, white RAL 9016 52

"Weatherproof" - for outdoor installation - harsh environment and/or outdoorfrom 1.5 up to 50 mm2

IP 66cable/conduit entry via metric knockouts- with / without terminals, colours grey RAL 7032, black RAL 9011 62 - 69box walls without knockouts - without terminals, colours grey RAL 7032, black RAL 901 71 - 74

17

DK Cable Junction Boxes Content

Additional information and planning tools (e.g. CAD parts libraries) can be found on the Internet at www.hensel-electric.in

"Waterproof" - for outdoor installation - harsh environment and/or outdoorfrom 1,5 up to 10 mm2 cable entry via metric knockouts- for encapsulating, colours grey RAL 7032, black RAL 9011 NEW 80 - 84

Tested for intrinsic fire resistance from 0.5 up to 16 mm2IP 65 / IP 66- material: duroplast, cable entry via included grommets, IP 65 94 - 95, 101- material: sheet steel, powder-coated, cable entry via mounted grommets, IP 66 96 - 100, 101

For special applicationsfrom 1.5 up to 25 mm2

IP 55 / IP 65cable entry via metric knockouts- for security lighting circuits, with red lid 103- for equipotential bonding conductors 104

With main line branch terminals from 25 up to 35 mm2

IP 55 / IP 65cable/conduit entry via metric knockouts- with terminal blocks for copper conductors 25 mm and 35 mm 106 - 107

With terminal blocks for aluminium- (Alu) and copper conductors (Cu) from 1.5 up to 4 mm2

IP 65cable/conduit entry via metric knockouts - Terminal boxes with terminal blocks 109 - 111

Accessories 113 - 121

"Weatherproof" - for outdoor installation - harsh environment and/or outdoorfrom 1.5 up to 50 mm2

IP 66 / IP 65 with UL/CSA approval, (Nema 4X)box walls without knockouts, can be drilled individually- without terminals 76 - 77

For offshore / heavy duty applicationsfrom 1.5 up to 35 mm2

IP 66 / IP 67cable entry via metric knockouts - with / without terminals 86 - 90box walls without knockouts - without terminals 91 - 92

Technical Details 123 - 134

18

DK Cable Junction Boxes Criteria for Selecting

Applications FunctionsBranching andconnecting ofcopper conduc-tors

Branching andconnecting ofaluminium and copper conduc-tors

In rooms with dry climate In damp and wet environments Protected outdoors (refer to technical details) On fl ameable parts of buildings In buildings with mainly infl ammable materials In areas with a high risk of fi re

Pages 22-52 Pages 54-60

Cable trunking installation Pages 43-44

Intrinsic fi re resistance Pages 94-101

"Waterproof" for encapsulating Pages 80-84

Weatherproof, for outdoor installation (harsh environment and/or outdoor)

Improved behaviour in cases of fi re ame-resistant and halogen-free

Pages 62-74

Offshore applications Pages 86-92

Security lighting circuits Page 103

Equipotential bonding Page 104

UL Approval Page 76-77

DNV Approval Germanisch Lloyd Russian Maritime Register of Shipping

Pages 62-92

PA

19

DK Cable Junction Boxes Criteria for Selecting

Connecting solid conductors and stranded conduc-tors

Combining multi-ple control wires to one control cable

2 circuits in one box

Main line branch terminals

Without terminals Box walls without knockouts

Page 54-55Pages 109-111

Pages 109-111 Pages 43-44DP 9220,DP 9221,DP 9222

Page 106-107 Pages 30-36, Page 41 DN 2000, DN 2030,Page 44, 47Page 48 DE 9321, Page 49,Page 51 DE 9220,Page 52 DE 9221, Pages 64-65, 68-69, 71-74, 76-77, 89-92Page 103 D 9220, D 9240

Pages 33-36all Boxes,Pages 71-74, 76-77Page 91-92

Pages 43-44DP 9220,DP 9221,DP 9222

Page 44

Pages 64-65Pages 68-69Pages 71-74

Pages 71-74

Pages 89-92 Page 91-92

Page 76-77

Pages 64-65, 68-69Pages 71-74, 89-92

Pages 71-74, 89-92

20

Assignment of box walls:

The assignment of box walls is effected via wall symbols that are

assigned to each product. The individual figures 2 give an indication,

which wall is concerned.

Wand4

65 5

Wall 18

4 x M 253 x M 40/50

Wall 19

8 x M 324 x M 40/50

Wall 20

2 x M 2010 x M 251 x M 32/40

Wall 21

1 x M 204 x M 251 x M 32/403 x M 40/50

Wall 22

1 x Elastic membranes

Wall 23

2 x Elastic membranes

Wall 24

3 x Elastic membranes

Wall 11 x M 20

Wall 21 x M 20/25

Wand 32 x M 20

Wall 42 x M 20/25

Wall 51 x M 20/251 x M 25/32

Wall 62 x M 25/32

Wall 72 x M 32

Wall 82 x M 32/40

Wall 92 x M 40

Wall 102 x M 20/251 x M 25/32

Wall 112 x M 20/251 x M 32/40

Wall 121 x M 20/251 x M 25/321 x M 40/50

Wall 131 x M 20/252 x M 40/50

Wall 14

3 x M 25/32

Wall 15

2 x M 25/321 x M 40/50

Wall 16

3 x M 32/40

Wall 17

4 x M 25/321 x M 40/50

Wall 25

1 x Removable-system

Wall 26

2 x Removable-system

Wall 27

3 x Removable-system

Wall 28

4 x Removable-system

DK Cable junction boxes Box Walls

All box walls are listed in the fold-out of the coverpages.

Wall 29

1 x M 63

Wall 30

2 x M 50

Wall 31

4 x up to 16 mm1 x up to 35 mm

21

DK Cable Junction Boxes with Terminals in Plug-in Technology Cable Entry via Metric Knockouts

Plenty of space for the wiring: Wiring facilities both below the DIN rails and between the terminals.

Different conductor types - rigid (r) and flexible (f) without treatment of conduc-tors - can be connected in one terminal.

Conductors can be directly connected and disconnected with installed terminal.

Stainless steel cover screws with quick fastening metric thread.Reducing cover xing time.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

Labelling system for circuit description Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

22

DK Cable Junction Boxes with Terminals in Plug-in Technology Cable Entry via Metric Knockouts

KC 9045

Wall10

106 5

1.5-4 mm, Cu 3~

FIXCONNECT plug-in terminal technology 5-pole per pole 4 x 1 x 1,5-4 mm sol/f, terminal technology,

see annex DK Cable junction boxes included cable entry: 4 ESM 25, sealing range 9-17 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 32 A

139

119

70

KC 9255

Wall16

118 8

2.5-10 mm, Cu 3~

FIXCONNECT plug-in terminal technology 5-pole per pole 4 x 1 x 2.5-10 mm r/f included cable entry: 3 ESM 32, sealing range 9-23 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 50 A

98

160

200

KC 9355

Wall13

1315 15

2.5-16 mm, Cu 3~

FIXCONNECT plug-in terminal technology 5-pole per pole 4 x 1 x 2.5-16 mm r/f included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 76 A

117260

210

23

DK Cable Junction Boxes Cable Entry via Metric Knockouts

Variable terminal mounting positions (5 positions) and new terminal technology

Included accessories as listed: grommets ESM = IP 55

Hensel cable junction boxes can in general also be used in poor environmental conditions by using IP 65 cable glands AKM/ASM.

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C / 960 C, flame-retardant, self-extinguishing

Labelling system for circuit description Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

24

DK Cable Junction Boxes Cable Entry via Metric Knockouts

D 9025

Wall

3

13 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol included cable entry: 4 ESM 20, sealing range 6-13 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

5388

88

D 9125

Wall

3

13 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol included cable entry: 4 ESM 20, sealing range 6-13 mm with external fixing for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

5388

88

D 9045

Wall

4

24 4

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol included cable entry: 4 ESM 25, sealing range 9-17 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98 61

98

D 9145

Wall

3

13 3

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol included cable entry: 4 ESM 20, sealing range 6-13 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98 61

98

25

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 9065

Wall10

106 5

2.5-6 mm, Cu 3~

with terminals 5-pole per pole 4 x 2.5 mm sol, 4 x 4 mm sol, 3 x 6 mm sol,

2 x 10 mm sol included cable entry: 3 ESM 32, sealing range 9-23 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,5 Nm

139

119

70

K 9105

Wall14

106 6

4-10 mm, Cu 3~

with terminals 5-pole per pole 6 x 2.5 mm sol, 4 x 4 mm sol, 4 x 6 mm sol,

4 x 10 mm sol, 2 x 16 mm s included cable entry: 3 ESM 32, sealing range 9-23 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 63 A tightening torque for terminal 2,0 Nm

82167

125

K 9255

Wall16

118 8

10-25 mm, Cu 3~

with terminals 5-pole per pole 6 x 10 mm sol, 4 x 16 mm s, 4 x 25 mm s,

2 x 35 mm s included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 102 A tightening torque for terminal 3,0 Nm

98

160

200

K 9502

Wall12

1217 17

10-35 mm, Cu 3~

with terminals 5-pole per pole 4 x 10 mm sol, 4 x 16 mm s, 4 x 25 mm s,

2 x 35 mm s included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 102 A tightening torque for terminal 3,0 Nm

310

210 117

26

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 9504

Wall12

1217 17

16-50 mm, Cu 3~

with terminals 4-pole per polel 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

4 x 50 mm s cable entry via knockouts,

order AKM/ASM separately (refer to index cable entry systems) for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 150 A tightening torque for terminal 12,0 Nm

310

210 117

K 9505

Wall12

1217 17

16-50 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

4 x 50 mm s cable entry via knockouts,

order AKM/ASM separately (refer to index cable entry systems) for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 150 A tightening torque for terminal 12,0 Nm

310

210 117

K 7055

Wall20

2021 21

16-50 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

4 x 50 mm s sealable Order cable glands, flanges and other accessories separately as

required for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 150 A tightening torque for terminal 12,0 Nm

450

300 170

K 9355

Wall15

1513 13

16-35 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

2 x 50 mm s included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 125 A tightening torque for terminal 12,0 Nm

117

260

210

27

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 7004

Wall20

2021 21

16-70 mm, Cu 3~

with terminals 4-pole per pole 4 x 16-70 mm s sealable Order cable glands, flanges and other accessories separately as

required for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 216 A tightening torque for terminal 10,0 Nm

450

300 170

K 7005

Wall20

2021 21

16-70 mm, Cu 3~

with terminals 5-pole per polel 4 x 16-70 mm s sealable Order cable glands, flanges and other accessories separately as

required for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 216 A tightening torque for terminal 10,0 Nm

450

300 170

K 1204

Wall20

2021 21

16-150 mm, Cu/Alu 3~

with terminals 4-pole per pole 2 x 16-150 mm, 4 x 16-70 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 250 A tightening torque for terminal 20,0 Nm

450

300 170

28

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 1205

Wall20

2021 21

16-150 mm, Cu/Alu 3~

with terminals 5-pole per pole 2 x 16-150 mm, 4 x 16-70 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 250 A tightening torque for terminal 20,0 Nm

450

300 170

K 2404

Wall20

1819 19

25-240 mm, Cu/Alu 3~

with terminals 4-pole per pole 2 x 25-185/240 mm, 4 x 25-120 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 400 A tightening torque for terminal 40,0 Nm

600

300 170

29

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 2405

Wall20

1819 19

25-240 mm, Cu/Alu 3~

with terminals 5-pole per pole 2 x 25-185/240 mm, 4 x 25-120 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 400 A tightening torque for terminal 40,0 Nm

600

300 170

30

DK Cable Junction Boxes Cable Entry via Metric Knockouts

D 9020

Wall

3

13 3

without terminals included cable entry: 4 ESM 20, sealing range 6-13 mm for normal environment and protected outdoor

5388

88

D 9120

Wall

3

13 3

without terminals with external fixing included cable entry: 4 ESM 20, sealing range 6-13 mm for normal environment and protected outdoor

5388

88

D 9140

Wall

3

13 3

without terminals included cable entry: 4 ESM 20, sealing range 6-13 mm for normal environment and protected outdoor

98 58

98

D 9040

Wall

4

24 4

without terminals included cable entry: 4 ESM 25, sealing range 9-17 mm for normal environment and protected outdoor

98 61

98

K 9060

Wall10

106 5

without terminals included cable entry: 3 ESM 32, sealing range 9-23 mm for normal environment and protected outdoor

139

119

70

K 9100

Wall14

106 6

without terminals included cable entry: 3 ESM 32, sealing range 9-23 mm for normal environment and protected outdoor

82167

125

31

DK Cable Junction Boxes Cable Entry via Metric Knockouts

K 9250

Wall16

118 8

without terminals included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

98

160

200

K 9350

Wall13

1315 15

without terminals included cable entry: 3 ESM 40, sealing range 17-30 mm for normal environment and protected outdoor

117260

210

K 9500

Wall12

1217 17

without terminals cable entry via knockouts, order AKM/ASM separately

(refer to index cable entry systems) for normal environment and protected outdoor

310

210 117

32

DK Cable Junction Boxes Box Walls without Knockouts

Cable entries can be drilled individually.

Labelling system for circuit description Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

33

DK Cable Junction Boxes Box Walls without Knockouts

D 8020

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 for normal environment and protected outdoor

wall thickness of the bottom part 2,3 mm

5388

88

D 8120

without terminals with external fixing box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 for normal environment and protected outdoor

wall thickness of the bottom part 2,3 mm

5388

88

D 8040

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 for normal environment and protected outdoor

wall thickness of the bottom part 2,3 mm

98 58

98 K 8060

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 for normal environment and protected outdoor

wall thickness of the bottom part 2,6 mm

139

119

70

K 8100

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 for normal environment and protected outdoor

wall thickness of the bottom part 2,8 mm

82167

125

34

DK Cable Junction Boxes Box Walls without Knockouts

K 8250

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 40 for normal environment and protected outdoor

wall thickness of the bottom part 3 mm

98

160

200

K 8350

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 for normal environment and protected outdoor

wall thickness of the bottom part 3 mm

117260

210

K 8500

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 for normal environment and protected outdoor

wall thickness of the bottom part 3 mm

31

0

210 117

35

DK Cable Junction Boxes Box Walls without Knockouts

K 0100

with transparent lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

150

K 0200

with transparent lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

300

K 0300

with transparent lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

450

K 0400

with transparent lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

600

300 170

36

DK Cable Junction Boxes Box Walls without Knockouts

K 0101

with opaque lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

150

K 0201

with opaque lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

300

K 0301

with opaque lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

300 170

450

K 0401

with opaque lid lid fasteners for tool operation box walls without knockouts please order DIN rails or mounting plates additionally for normal environment and protected outdoor

rated current for electrical devices up to 63 A wall thickness of the bottom part 3,5 mm

600

300 170

37

DK Cable Junction Boxes Empty Boxes Accessories for Cable Junction Boxes K0x0x

Mi TS 15

DIN raillength 134 mm in accordance with DIN EN 60 715 for Mi Empty box size 1 for equipment or terminals with clip-on mounting with fixing screws

35

15134

Mi TS 30

DIN raillength 284 mm in accordance with DIN EN 60 715 for Mi empty box sizes 1 to 8 for equipment or terminals with clip-on mounting with fixing screws

35

15284

Mi TS 45

DIN raillength 434 mm in accordance with DIN EN 60 715 for Mi empty box size 3 for equipment or terminals with clip-on mounting with fixing screws

35

15434

Mi TS 60

DIN raillength 584 mm in accordance with DIN EN 60 715 for Mi empty box sizes 4 and 8 for equipment or terminals with clip-on mounting with fixing screws

35

15584

Mi MP 1

Mounting plateW 259 x H 115 mm material thickness 4 mm for Mi-Empty boxes sizes 1, 2, 3, 4 with fixing screws

259

115

Mi MP 2

Mounting plateW 265 x H 265 mm material thickness 4 mm for Mi-Empty boxes sizes 2 to 8 with fixing screws

265

265

38

DK Cable Junction Boxes Empty Boxes Accessories for Cable Junction Boxes K0x0x

Mi MP 3

Mounting plateW 265 x H 415 mm material thickness 4 mm for Mi-Empty boxes sizes 3, 4 with fixing screws

415

265

Mi MP 4

Mounting plateW 265 x H 565 mm material thickness 4 mm for Mi-Empty boxes sizes 4, 8 with fixing screws

565

265

Mi PL 2

Sealing cap 2 sealing caps for converting the lid fasteners

Mi SR 4

Conversion setfor manual operation on tool operation 4 fastening covers

Mi SN 4

Conversion setfor converting lid fasteners from tool to manual operation 4 manual actuators

39

DK Cable Junction Boxes Empty Boxes Accessories for Cable Junction Boxes K0x0x

Mi DV 01

L ocking device insertion only in connection with Mi PL 2, Mi SR 4 or Mi SN 4

Mi ZS 11

Lid lockwith locking device I Is being used instead of fasteners for hand or tool operation in

order to prevent unauthorised opening of the lids consisting of: cylinder lock, keys, locking device insertion, dust

cover

Mi ZS 12

Lid lockwith locking device II Is being used instead of fasteners for hand or tool operation in

order to prevent unauthorised opening of the lids consisting of: cylinder lock, keys, locking device insertion, dust

cover

Mi DR 04

Lid fastener for tool operationtriangle 8 mm is used instead of fasteners for hand- or tool operation, in order to

make unauthorized opening of lids more difficult 4 locking devices with triangle 8 mm and key

DS 1

Triangular key 8 mm

Mi AL 40

4 stainless steel external brackets for external fixing of enclosures

40

DK Cable Junction Boxes Cable Entry via Elastic Membranes and Integrated M 20 Thread

IP 55 with cable entry via elastic membranes.

IP 65 with ADM 20 cable gland without locknut. The gland is secured by an integrated M 20 thread.

Captive cover screws with quick-release lock.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

41

DK Cable Junction boxes Cable Entry via Elastic Membranes and Integrated M 20 Thread

DN 2035

Wall

3

33 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol cable entry via elastic membranes and integrated M 20 thread 8 elastic membranes, closed, sealing range 3-12 mm included cable entry: 3 ADM 20, sealing range 6,5-13,5 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

DN 2005

Wall

3

33 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol cable entry via elastic membranes and integrated M 20 thread 8 elastic membranes, closed, sealing range 3-12 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

DN 2030

Wall

3

33 3

without terminals cable entry via elastic membranes and integrated M 20 thread 8 elastic membranes, closed, sealing range 3-12 mm included cable entry: 3 ADM 20, sealing range 6,5-13,5 mm

DN 2000

Wall

3

33 3

without terminals cable entry via elastic membranes and integrated M 20 thread 8 elastic membranes, closed, sealing range 3-12 mm for normal environment and protected outdoor

ADM 20

ISO thread M 20 x 1.5

sealing range 6,5-13,5 mm with strain relief for indoor - normal environment and (or) protected outdoor installation ambient temperature - 25 to + 35 C glow wire test IEC 60 695-2-11: 750 C

tightening torque 2,0 Nm

42

DK Cable Junction Boxes Cable Entry via Knockouts for Cable Trunking and Conduit Installation

Simply cut out cable trunking wall to the required width.

The cables can be inserted from the front! No threading of cables neccessary!

Supplied accessory grommets DPS 02 = IP 54

The clean installation solution for cable trunking!

Removable trunking adapters for connection of cable trunkings to junction boxes.

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

Labelling system for circuit description Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

43

DK Cable Junction Boxes Cable Entry via Knockouts for Cable Trunking and Conduit Installation

DP 9025

Wall26

2526 26

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol for cable trunking and conduit installation included cable entry: 4 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

5088

88

DP 9221

Wall28

2727 27

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol for cable trunking and conduit installation included cable entry: 7 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

50139

119

DP 9222

Wall28

2727 27

1.5-2.5 mm, Cu 3~

with 2 terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol for cable trunking and conduit installation included cable entry: 7 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

50139

119

DPC 9225

Wall28

2727 27

1.5-2.5 mm, Cu 3~

FIXCONNECT plug-in terminal technology 5-pole per pole 4 x 1 x 1.5-2.5 mm sol/f, terminal technology,

see annex DK Cable junction boxes for cable trunking and conduit installation included cable entry: 4 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 32 A

50139

119

44

DK Cable Junction Boxes Cable Entry via Knockouts for Cable Trunking and Conduit Installation

DP 9020

Wall26

2526 26

without terminals for cable trunking and conduit installation included cable entry: 4 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

5088

88

DP 9220

Wall28

2727 27

without terminals for cable trunking and conduit installation included cable entry: 7 DPS 02, sealing range 10-13,5 mm for normal environment and protected outdoor

50139

119

DPS 02

Removable grommet

degree of protection: IP 54 sealing range 10-13.5 mm for retrofitting for cable junction boxes DP 9020, DP 9220, DP 9025, DP 9221, DP 9222, DP 9026, DPC 9225

ERA 20

Removable conduit adapter

degree of protection: IP 54 sealing range 10-13.5 mm for wiring conduits M 20 for cable junction boxes DP 9020, DP 9220, DP 9025, DP 9221, DP 9222, DP 9026, DPC 9225

EKA 20

Removable trunking adapter

degree of protection: IP 54 sealing range 10-13.5 mm for mini trunking up to 20 x 20 mm for cable junction boxes DP 9020, DP 9220, DP 9025, DP 9221, DP 9222, DP 9026, DPC 9225

45

DK Cable Junction Boxes Cable Entry via Elastic Membranes

No punching tool required - insert the conductor and its done

Degree of protection IP 55

Grommet supplied for sealing membra-nes in case of modifications.

Box wall with 3 cable entries Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

Labelling system for circuit description Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

46

DK Cable Junction Boxes Cable Entry via Elastic Membranes

DE 9325

Wall24

2423 23

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

4788

88

DE 9345

Wall24

2423 23

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98

98 52

DE 9335

Wall24

2423 23

1.5-4 mm, Cu 3~

terminals with wire protection 5-pole per pole 4 x 1.5 mm sol/s/f, 4 x 2.5 mm sol/s/f,

2 x 4 mm sol/s/f 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

rated insulation voltage AC/DC 500 V rated current 32 A tightening torque for terminal 0,8 Nm Dismantling length 6 mm

4788

88

47

DK Cable Junction Boxes Cable Entry via Elastic Membranes

DE 9320

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm for normal environment and protected outdoor

4788

88

DE 9340

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm for normal environment and protected outdoor

98

98 52

DE 9330

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

4788

88

DE 9350

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

98

98 52

48

DK Cable Junction Boxes Cable Entry via Elastic Membranes

DE 9326

Wall24

2423 23

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

4788

88

DE 9346

Wall24

2423 23

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98

98 52

DE 9336

Wall24

2423 23

1.5-2.5 mm, Cu 3~

terminals with wire protection 5-pole per pole 4 x 1.5 mm sol/s/f, 4 x 2.5 mm sol/s/f,

2 x 4 mm sol/s/f 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

rated insulation voltage AC/DC 500 V rated current 32 A tightening torque for terminal 0,8 Nm Dismantling length 11 mm

4788

88

DE 9321

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm for normal environment and protected outdoor

4788

88

49

DK Cable Junction Boxes Cable Entry via Elastic Membranes

DE 9341

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm for normal environment and protected outdoor

98

98 52

DE 9331

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-16 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

4788

88

DE 9351

Wall24

2423 23

without terminals 10 elastic membranes, closed cable entries,

sealing range 6.5-18 mm with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

98

98 52

KHR 01

Cable retentionfor cable diameter 6,5 - 14 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 6,5 - 10 mm 30 pieces for cable diameter 10 - 14 mm

KHR 02

Cable retentionfor cable diameter 10 - 16 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 10 - 14 mm 30 pieces for cable diameter 13 - 16 mm

DK ZE 10

Cable retention set with 10 pieces for fixing in the bottom part of DK-cable junction boxes cable retention with cable clip up to 6.5 mm

50

DK Cable Junction Boxes Cable Entry via Elastic Membranes in Bottom and Box Walls

Cable entry from the rear via elastic membranes in the bottom

Lid for clip-on attachment. Reducing cover xing time

Flexible elastic membranes -no cable glands required. Push through and tight!

Cable entry via elastic membranes in box walls

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

51

DK Cable Junction Boxes Cable Entry via Elastic Membranes in Bottom and Box Walls

DE 9225

Wall23

2324 24

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol box walls with 10 elastic membranes, closed, sealing range

3-14 mm, bottom with 2 elastic membranes, closed lid with clip-on attachment for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

DE 9220

Wall23

2324 24

without terminals box walls with 10 elastic membranes, closed, sealing range

3-14 mm, bottom with 2 elastic membranes, closed lid with clip-on attachment with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

DK ZE 10

Cable retention set with 10 pieces for fixing in the bottom part of DK-cable junction boxes cable retention with cable clip up to 6.5 mm

KHR 01

Cable retentionfor cable diameter 6,5 - 14 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 6,5 - 10 mm 30 pieces for cable diameter 10 - 14 mm

KHR 02

Cable retentionfor cable diameter 10 - 16 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 10 - 14 mm 30 pieces for cable diameter 13 - 16 mm

DE MB 10

Assembly bracket external brackets 10 units material: thermoplastics for quick installation of cable junction boxes DE 922. and DN 20..

52

DK Cable Junction Boxes Cable Entry via Elastic Membranes in Bottom and Box Walls

DE 9226

Wall23

2324 24

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol box walls with 10 elastic membranes, closed, sealing range

3-14 mm, bottom with 2 elastic membranes, closed lid with clip-on attachment for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

DE 9221

Wall23

2324 24

without terminals box walls with 10 elastic membranes, closed, sealing range

3-14 mm, bottom with 2 elastic membranes, closed lid with clip-on attachment with cable retention (2 pc.) for cable tie up to 6.5 mm width for normal environment and protected outdoor

DK ZE 10

Cable retention set with 10 pieces for fixing in the bottom part of DK-cable junction boxes cable retention with cable clip up to 6.5 mm

KHR 01

Cable retentionfor cable diameter 6,5 - 14 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 6,5 - 10 mm 30 pieces for cable diameter 10 - 14 mm

KHR 02

Cable retentionfor cable diameter 10 - 16 mm set with 10 x 6 cable rentention rings 30 pieces for cable diameter 10 - 14 mm 30 pieces for cable diameter 13 - 16 mm

DE MB 10

Assembly bracket external brackets 10 units material: thermoplastics for quick installation of cable junction boxes DE 922. and DN 20..

53

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

Degree of protection up to IP 65. In the case of twisted cables, cable glands are required in principle to achieve the degree of protection IP 54.

Separate clamping units for aluminium and copper conductors

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Burning behaviour:Glow wire test according to IEC 60 695-2-11: 750 C, flame-retardant, self-extinguishing

Labelling system for circuit description. Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

54

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

D 9041

Wall

4

24 4

1.5-2.5 mm, Cu/Alu 3~

with terminals 5-pole per polel 4 x 1.5 mm sol/f, 4 x 2.5 mm sol/f, conductors

are inserted into the screw-type terminal, terminal technology, see annex DK Cable junction boxes

included cable entry: 4 ESM 25, sealing range 9-17 mm In the case of twisted cables, cable glands are required in

principle to achieve the degree of protection IP 54. Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 250 V current carrying capacity 20 A tightening torque for terminal 0,5 Nm

98 61

98

K 9061

Wall10

106 5

1.5-4 mm, Cu/Alu 3~

with terminals 5-pole per pole 4 x 1.5 mm sol/f, 4 x 2.5 mm sol/f, 4 x 4 mm

sol/f, conductors are inserted into the screw-type terminal, terminal technology, see annex DK Cable junction boxes

included cable entry: 3 ESM 32, sealing range 9-23 mm In the case of twisted cables, cable glands are required in

principle to achieve the degree of protection IP 54. Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 400 V current carrying capacity 20 A tightening torque for terminal 0,6 Nm

139

119

70

55

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

K 9351

Wall13

1315 15

6-16 mm, Cu/Alu 3~

with terminals 5-pole per polel 4 x 6 mm sol/f, 4 x 10 mm sol/f, 4 x 16 mm

sol/s/f, conductors are inserted into the screw-type terminal, terminal technology, see annex DK Cable junction boxes

included cable entry: 3 ESM 40, sealing range 17-30 mm In the case of twisted cables, cable glands are required in

principle to achieve the degree of protection IP 54. Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 76 A tightening torque for terminal 3,0 Nm

117260

210

KF 9251

Wall16

118 8

1.5-50 mm, Cu/Alu 3~

with connecting terminal 5-pole per pole 2 x 1 x 1.5-50 mm, conductors are inserted into

the screw-type terminal, terminal technology, see annex DK Cable junction boxes

included cable entry: 2 EDK 40, sealing range 11-30 mm Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 160 A tightening torque for terminal 1.5 Nm 1.5-2.5 mm

5.0 Nm 4-10 mm 12,0 Nm 16-50 mm

98

160

200

56

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

KF 9501

Wall12

1217 17

1.5-50 mm, Cu/Alu 3~

with connecting terminal 5-pole per pole 2 x 1 x 1.5-50 mm, conductors are inserted into

the screw-type terminal, terminal technology, see annex DK Cable junction boxes

included cable entry: 2 EDK 40, sealing range 11-30 mm Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 160 A tightening torque for terminal 1.5 Nm 1.5-2.5 mm

5.0 Nm 4-10 mm 12,0 Nm 16-50 mm

310

210 117

K 7051

Wall20

2021 21

2.5-50 mm, Cu/Alu 3~

with terminals 5-pole per pole 4 x 2.5-50 mm, conductors are inserted into the

screw-type terminal, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 750 V current carrying capacity Cu, 150 A

Alu, 120 A tightening torque for terminal 10,0 Nm

450

300 170

57

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

K 7042

Wall20

2021 21

10-95 mm Cu/Alu 3~

with terminals 4-pole per pole 2 x 10-95 mm, conductors can be inserted from

the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 160 A tightening torque for terminal 20,0 Nm

450

300 170

K 7052

Wall20

2021 21

10-95 mm Cu/Alu 3~

with terminals 5-pole per pole 2 x 10-95 mm, conductors can be inserted from

the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 160 A tightening torque for terminal 20,0 Nm

450

300 170

58

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

K 9951

Wall20

2021 21

6-95 mm, Cu/Alu 3~

with terminals 5-pole per pole 4 x 6-95 mm, conductors are inserted into the

screw-type terminal, terminal technology, see annex DK Cable junction boxes

Order cable glands, flanges and other accessories separately as required

Reference to the preparation of aluminum conductors: 1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 490 A tightening torque for terminal 12.0 Nm 6-25 mm

22.0 Nm 35-95 mm

450

300 170

K 1204

Wall20

2021 21

16-150 mm, Cu/Alu 3~

with terminals 4-pole per pole 2 x 16-150 mm, 4 x 16-70 mm, conductors can

be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 250 A tightening torque for terminal 20,0 Nm

450

300 170

59

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

K 1205

Wall20

2021 21

16-150 mm, Cu/Alu 3~

with terminals 5-pole per pole 2 x 16-150 mm, 4 x 16-70 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 250 A tightening torque for terminal 20,0 Nm

450

300 170

K 2404

Wall20

1819 19

25-240 mm, Cu/Alu 3~

with terminals 4-pole per pole 2 x 25-185/240 mm, 4 x 25-120 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 400 A tightening torque for terminal 40,0 Nm

600

300 170

60

DK Cable Junction Boxes with Terminals for Aluminium and Copper Conductors Cable Entry via Metric Knockouts

K 2405

Wall20

1819 19

25-240 mm, Cu/Alu 3~

with terminals 5-pole per pole 2 x 25-185/240 mm, 4 x 25-120 mm,

conductors can be inserted from the front into the clamping unit, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 400 A tightening torque for terminal 40,0 Nm

600

300 170

K 2401

Wall20

1819 19

35-240 mm, Cu/Alu 3~

with terminals 5-pole per pole 4 x 35-240 mm, conductors are inserted into the

screw-type terminal, terminal technology, see annex DK Cable junction boxes

sealable Order cable glands, flanges and other accessories separately as

required Reference to the preparation of aluminum conductors:

1. Clean the bared conductor end carefully by scraping off the oxide film, for example with a knife, (Please do not use rasps, emery paper or brushes!). 2. Immediately after removing the oxide film the conductor end is to rub in with acid and alkali free fat for example vaseline, and immediately to be connected in the terminal. 3. The prementioned processing steps are to be repeated, if the conductor was disconnected and connected again. 4. Due to the disposition to flowing of aluminum the terminals are to be re-tightened before start-up and after the first 200 operation hours.

for normal environment and protected outdoor

rated insulation voltage AC/DC 690 V current carrying capacity 850 A tightening torque for terminal 26.0 Nm 35-120 mm

55.0 Nm 150-240 mm

600

300 170

61

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

Degree of protection IP 66 Flame retardant, self-extinguishing,

made of high-grade material:PC-GFS, glass- bre reinforced thermoplastics, impact proof

KF-Cable junction boxes comply with regulatory restrictions for buildings with requirements regarding the structural fire protection!

halogen-free, silicone-free:low toxicity, low fume development

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Burning behaviour:Glow-wire test 960C according to IEC 60 695-2-11, UL Subject 94: V-0 ame-retardant, self-extinguishing

Degree of protection IP 66 using cable glands ASS.. (colour black) or cable glands ASM.. (colour grey), available as an accessory.

62

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 9025

Wall

3

13 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

5388

88

KF 9045

Wall

4

24 4

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98 61

98

KF 9065

Wall10

106 5

2.5-6 mm, Cu 3~

with terminals 5-pole per pole 4 x 2.5 mm sol, 4 x 4 mm sol, 3 x 6 mm sol,

2 x 10 mm sol cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,5 Nm

139

119

70

KF 9105

Wall14

106 6

4-10 mm, Cu 3~

with terminals 5-pole per pole 6 x 2.5 mm sol, 4 x 4 mm sol, 4 x 6 mm sol,

4 x 10 mm sol, 2 x 16 mm s cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 63 A tightening torque for terminal 2,0 Nm

82167

125

63

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 9255

Wall16

118 8

10-25 mm, Cu 3~

with terminals 5-pole per pole 6 x 10 mm sol, 4 x 16 mm s, 4 x 25 mm s,

2 x 35 mm s cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 102 A tightening torque for terminal 3,0 Nm

98

160

200

KF 9355

Wall15

1513 13

16-35 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

2 x 50 mm s cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 125 A tightening torque for terminal 12,0 Nm

117

260

210

KF 9505

Wall12

1217 17

16-50 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

4 x 50 mm s cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 150 A tightening torque for terminal 12,0 Nm

310

210 117

64

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 9020

Wall

3

13 3

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

5388

88

KF 9040

Wall

4

24 4

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

98 61

98

KF 9060

Wall10

106 5

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

139

119

70

KF 9100

Wall14

106 6

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

82167

125

KF 9250

Wall16

118 8

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

98

160

200

65

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 9350

Wall13

1315 15

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

117260

210

KF 9500

Wall12

1217 17

without terminals cable entry via knockouts, order ASM separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

310

210 117

66

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 5025

Wall

3

13 3

1.5-2.5 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

5388

88

KF 5045

Wall

4

24 4

1.5-4 mm, Cu 3~

with terminals 5-pole per pole 6 x 1.5 mm sol, 4 x 2.5 mm sol, 3 x 4 mm sol,

2 x 6 mm sol cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,2 Nm

98 61

98

KF 5065

Wall10

106 5

2.5-6 mm, Cu 3~

with terminals 5-pole per pole 4 x 2.5 mm sol, 4 x 4 mm sol, 3 x 6 mm sol,

2 x 10 mm sol cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V tightening torque for terminal 1,5 Nm

139

119

70

KF 5105

Wall14

106 6

4-10 mm, Cu 3~

with terminals 5-pole per pole 6 x 2.5 mm sol, 4 x 4 mm sol, 4 x 6 mm sol,

4 x 10 mm sol, 2 x 16 mm s cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 63 A tightening torque for terminal 2,0 Nm

82167

125

67

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 5255

Wall16

118 8

10-25 mm, Cu 3~

with terminals 5-pole per pole 6 x 10 mm sol, 4 x 16 mm s, 4 x 25 mm s,

2 x 35 mm s cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 102 A tightening torque for terminal 3,0 Nm

98

160

200

KF 5355

Wall15

1513 13

16-35 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

2 x 50 mm s cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 125 A tightening torque for terminal 12,0 Nm

117

260

210

KF 5505

Wall12

1217 17

16-50 mm, Cu 3~

with terminals 5-pole per pole 6 x 16 mm s, 4 x 25 mm s, 4 x 35 mm s,

4 x 50 mm s cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

rated insulation voltage AC/DC 690 V current carrying capacity 150 A tightening torque for terminal 12,0 Nm

310

210 117

68

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 5020

Wall

3

13 3

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

5388

88

KF 5040

Wall

4

24 4

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

98 61

98

KF 5060

Wall10

106 5

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

139

119

70

KF 5100

Wall14

106 6

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

82167

125

KF 5250

Wall16

118 8

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

98

160

200

69

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Cable Entry via Metric Knockouts

KF 5350

Wall13

1315 15

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

117260

210

KF 5500

Wall12

1217 17

without terminals cable entry via knockouts, order ASS separately

(refer to index cable entry systems) "Outdoor - harsh environment and (or) outdoor"

310

210 117

70

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Box Walls without Knockouts

Cable entries can be drilled individually Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Labelling system for circuit description. Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

Burning behaviour:Glow-wire test 960 C according to IEC 60 695-2-11, UL Subject 94: V-0 ame-retardant, self-extinguishing

71

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Box Walls without Knockouts

KF 8020

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,3 mm

5388

88

KF 8040

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,3 mm

98 58

98

KF 8060

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,6 mm

139

119

70

KF 8100

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,8 mm

82167

125

72

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Box Walls without Knockouts

KF 8250

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 40 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

98

160

200

KF 8350

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

117260

210

KF 8500

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

310

210 117

73

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Box Walls without Knockouts

KF 4020

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,3 mm

5388

88

KF 4040

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 20 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,3 mm

98 58

98

KF 4060

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,6 mm

139

119

70

KF 4100

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 32 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 2,8 mm

82167

125

74

DK Cable Junction Boxes Weatherproof, for Outdoor Installation Box Walls without Knockouts

KF 4250

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 40 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

98

160

200

KF 4350

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

117260

210

KF 4500

without terminals box walls without knockouts wall surface can be drilled individually for cable entry max. M 50 "Outdoor - harsh environment and (or) outdoor"

wall thickness of the bottom part 3 mm

310

210 117

75

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Labelling system for circuit description. Label template on the Internet at

www.hensel-electric.de - in the Downloads area.

Burning behaviour:Glow-wire test 960 C according to IEC 60 695-2-11, UL Subject 94: V-0 ame-retardant, self-extinguishing

DK Cable Junction Boxes Weatherproof, for Outdoor InstallationApproved for United States and Canada (UL/CSA)Box Walls without Knockouts

Cable junction boxes with external brackets made of stainless steel.

Cable entries can be drilled individually.

Approved for United States and Canada

76

DK Cable Junction Boxes Weatherproof, for Outdoor InstallationApproved for United States and Canada (UL/CSA)Box Walls without Knockouts

KF 7020

without terminals with UL/CSA approval box walls without knockouts wall surface can be drilled individually for cable entry M 20,

NPT 3/8" and NPT 1/2"

wall thickness of the bottom part 2,3 mm external brackets 2

5388

88

KF 7040

without terminals with UL/CSA approval box walls without knockouts wall surface can be drilled individually for cable entry M 20,

NPT 3/8" and NPT 1/2"

wall thickness of the bottom part 2,3 mm external brackets 2

98 58

98

KF 7060

without terminals with UL/CSA approval box walls without knockouts wall surface can be drilled individually for cable entry M 20/25/32,

NPT 3/8", NPT 1/2" and NPT 3/4"

wall thickness of the bottom part 2,6 mm external brackets 2

139

119

70

KF 7100

without terminals with UL/CSA approval box walls without knockouts wall surface can be drilled individually for cable entry M 20/25/32,

NPT 3/8", NPT 1/2", NPT 3/4" and 1"

wall thickness of the bottom part 2,8 mm external brackets 2

82167

125

77

DK Cable Junction Boxes Weatherproof, for Outdoor InstallationApproved for United States and Canada (UL/CSA)Box Walls without Knockouts

KF 7250

without terminals with UL/CSA approval box walls without knockouts wall surface can be drilled individually for cable entry M 20/25/32,

NPT 3/8", NPT 1/2", NPT 3/4" and 1"

wall thickness of the bottom part 3 mm external brackets 4

98

160

200

78

DK Cable Junction Boxes Waterproof , for Encapsulating

Cable junction boxes for encapsulating In case of re-installation or testing the sealing compound can be removed easily

Stainless steel cover screws with quick fastening metric thread. Reducing cover xing time.

Scope of application:Ground level installations

Scope of application:Pump shafts

Scope of application:Flood areas close to rivers orunprotected outdoor installations which are in close proximity to the ground

The ingress of water and formation of condensation are completely prevented.The sealing compound can be easily removed for subsequent installations or inspections.

79

DK Cable Junction Boxes Waterproof , for Encapsulating

Permanent waterproof

connection -

Cable junction boxes

for encapsulating

in accordance with

DIN VDE V 0606-22-100

Time and time again, electricians come across installation envi-ronments whereby the ingress of water into an enclosure must be safely excluded. Even enclo-sures which have a high degree of protection cannot guarantee this. The IP degree of protection allows the ingress of non-harmful quantities of water in the interior of an enclosure.

Under extreme environmental conditions, for example, the ac-cumulation of condensation may result in damage to the electrical installation or devices or cause these to malfunction.

Ventilation measures will often suffice to prevent harmful con-densation from forming.

In many cases, however, ventila-tion is not possible, e.g. because the cable junction boxes are in-stalled close to rivers and water could enter through the vent holes.

Which applications require waterproof connections?

Pump shafts Ground-level installation ducts

in outdoor areas

Flood areas close to rivers Unprotected outdoor instal-

lations which are in close proximity to the ground

Why is the IP degree of pro-tection alone not sufficient?

All degrees of protection al-lowed Water ingress

The accumulation of con-densation cannot always be prevented

Ventilation measures cannot be applied in all environments

The waterproof connection

Sealing the cable junction boxes with a fast setting, permanently elastic sealing compound com-pletely the ingress of water and the

excludes forming of condensation.

The sealing compound fea-tures outstanding insula-tion properties. As the com-pound is transparent, it is possible for visual inspections of the installation to be carried out at any time. The durable elastic material is self-sealing, therefore it is also easy for the electrical con-nections to b