01430870P---%20EPHD,RPHD,HPHD,SPHD%20PUB%2005-04%20Rev%2005-07.pdf

© 2007 Alamo Group Inc.

RHINO®

1020 S. Sangamon Ave.Gibson City, IL 60936800-446-5158Email: [email protected]

PART'S MANUALAn Operator's Manual was shipped with the equipment in theManual Canister. This Operator's Manual is an integral part ofthe safe operation of this machine and must be maintainedwith the unit at all times. READ, UNDERSTAND, and FOLLOWthe Safety and Operation Instructions contained in this manualbefore operating the equipment. If the Operator's Manual isnot with the equipment, contact your dealer or Servis-Rhino(800-446-5158) to obtain a Free copy before operating theequipment.

POST HOLE DIGGEREPHD Economy DutyRPHD Regular DutyHPHD Heavy DutySPHD Super DutyHydraulic Drive

Rev 05-07 Part No. 01430870P

TO THE OWNER/OPERATOR/DEALERAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator whorecognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement tobe used with all its safety equipment properly attached to minimize the chance of accidents.

BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.Observe the rules of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Formin full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Cardand on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophicfailure with possible injury or death.

PARTSSECTION

Parts Section – 1

Parts Section – 2©2007 Alamo Group Inc.

For maximum safety and to guarantee optimum product reliability, always usegenuine Servis-Rhino Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.Direct any questions regarding parts to:

The following instructions are offered to help eliminate needless delay and error in processingpurchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong to thebasic machine featured in this manual. Part Numbers and Descriptions are given to helplocate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organizationordering the parts, who should be charged, and if possible, the serial number of the machinefor which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked andare subject to special handling. Request a quotation for such parts before sending aPurchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.

NOTE: Please refer to The Safety Section in the front of this Manual for the properPart Number when ordering Replacement Safety Decals.

PARTS ORDERING GUIDE

RHINO®


PART NAME INDEX

AUGER ASSEMBLIES ........................................................................................................................................................... 6AUGER ASSEMBLIES - EPHD............................................................................................................................................ 14BOLT-ON BUCKET MOUNT ASSEMBLY (OPTION) .......................................................................................................... 39CLAMP MOUNT ASSEMBLY (OPTION).............................................................................................................................. 36CLUTCH - RADIAL PIN........................................................................................................................................................ 30DISPLAY STAND ASSEMBLY (OPTION) Rev 04-06.......................................................................................................... 37DOWN PRESSURE KIT (EXTRA EQUIPMENT - USED W/SPHD ONLY) Rev 04-06 ....................................................... 31DRIVELINE ASSEMBLY - RPHD,HPHD, & SPHD 00768283 Rev 05-04......................................................................... 19DRIVELINE ASSEMBLY - SHEAR BOLT EPHD - S/N 10141 THROUGH 10233.............................................................. 23DRIVELINE ASSEMBLY - SHEAR BOLT 00773134 ........................................................................................................... 16DRIVELINE ASSEMBLY - SHEAR PIN EPHD - S/N 10234 AND 10760............................................................................ 22DRIVELINE ASSEMBLY- RADIAL CLUTCH (OPTIONAL) Rev 11-05................................................................................ 20DRIVELINE ASSY - SHEAR PIN EPHD - S/N 10761-11743 .............................................................................................. 21DRIVELINE ASSY -HPHD, RPHD,SPHD & EPHD 00768283A Rev 05-07 ...................................................................... 18GEARBOX ASSEMBLY - EPHD .......................................................................................................................................... 28GEARBOX ASSEMBLY - HYDRAULIC DRIVE Rev 05-05 ................................................................................................. 34GEARBOX ASSEMBLY WW 3.5 HD 3.5:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO RPHD & HPHD .................. 24GEARBOX ASSEMBLY WW4HD 4:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO SPHD.......................................... 26HITCH AND BOOM PARTS LIST Rev 04-06 ........................................................................................................................ 4HYDRAULIC DRIVE ASSEMBLY......................................................................................................................................... 32SAFETY DECALS................................................................................................................................................................. 40UNIVERAL CHAIN MOUNT ASSEMBLY (OPTION)............................................................................................................ 3812 INCH AUGER ASSEMBLY Rev 05-07............................................................................................................................ 1015 INCH AUGER ASSEMBLY Rev 05-07............................................................................................................................ 1118 INCH AUGER ASSEMBLY Rev 05-07............................................................................................................................ 1224 INCH AUGER ASSEMBLY Rev 05-07............................................................................................................................ 136 INCH AUGER ASSEMBLY Rev 05-07................................................................................................................................ 89 INCH AUGER ASSEMBLY Rev 05-07................................................................................................................................ 9

PHD- EPHD,RPHD,HPHD,SPHD(May-04) -Current Rev 05-07

©2007 Alamo Group Inc. Parts Section – 3

HITCH AND BOOM PARTS LIST Rev 04-06



HITCH AND BOOM PARTS LIST Rev 04-06

ITEM PART NO. RPHD HPHD SPHD EPHD DESCRIPTION

3 00000400 2 2 2 2 COTTER PIN4 01430010 1 1 1 1 MOUNTING SHAFT5 01403020 2 2 2 2 BOLT7 00015800 2 2 2 2 TOPLOCKNUT, 3/8 NC8 01A01010 1 1 GUIDING LEVER (N/A FOR 4:1 GEARBOX)(S/N

11158 AND BELOW)(EXTRA EQUIPMENT)01101280 1 1 1 GUIDING LEVER (N/A FOR 4:1 GEARBOX)(S/N

11159 AND UP)(EXTRA EQUIPMENT)(WHOLEGOODS ONLY)

00768161 1 GUIDING LEVER (WHOLEGOODS ONLY)8A 00767042 1 1 1 1 GUIDE LEVEL DECAL9 01A01100 1 1 BOOM/CRANE (FOR RPHD)

01A01020 1 1 BOOM/CRANE (FOR HPHD & SPHD)10 63066100 2 2 BOLT

00755948 2 BOLT11 00012101 2 2 LOCKWASHER

00755954 2 LOCKWASHER12 00011100 2 2 FLATWASHER13 00606000 2 2 2 2 COTTER PIN14 01100020 1 1 YOKE PIN - 7-1/8 INCH LONG (SHOWN)

01100010 1 1 YOKE PIN - 5 INCH LONG15 01100070 1 1 HITCH FRAME (SHOWN)

01100030 1 1 HITCH FRAME00766644 1 HITCH FRAME (CAT II)

16 01100100 2 2 HITCH PIN (SHOWN) CAT I & II17 01430140 1 1 BUSHING (FOR CAT 1 USE)22 00770594 1 1 1 1 SHIELD (RPHD S/N 14850 AND UP)(HPHD S/N

14092 AND UP)(SPHD S/N 14444 AND UP)00760700 1 1 1 SHIELD (RPHD S/N 11729 AND 14849)(HPHD S/N

11567 AND 14091)(SPHD S/N 11855 AND 14443)23 00770592 1 1 1 SHIELD BRKT PLATE

00768467 1 SHIELD BRKT PLATE (EPHD S/N 10142 AND UP)24 26168 2 2 2 2 CARRIAGE BOLT25 02961255 2 2 2 2 PUSH NUT26 00769933 2 2 2 2 THUMB NUT27 4405 2 2 2 2 COTTER PIN28 00764259 1 1 1 1 CHAIN29 00767039 1 1 1 1 DANGER: SHIELD MISSING DECAL



AUGER ASSEMBLIES



AUGER ASSEMBLIES

ITEM PART NO. QTY. DESCRIPTION

¤ STANDARD AUGER AND PARTS1 00767673 1 6 INCH AUGER (USED ON EPHD ONLY)

00767674 1 9 INCH AUGER (USED ON EPHD ONLY)00767675 1 12 INCH AUGER (USED ON EPHD ONLY)00767676 1 14 INCH AUGER00767677 1 18 INCH AUGER01A01240 1 24 INCH AUGER

2 01100110 1 SPIRAL POINT01100130 1 FISHTAIL POINT

3 00764375 2 BOLT4 00001800 3 NUT5 00999418 1 BOLT (USED ON 12,14,18 AND 24 INCH AUGERS)

000245 1 BOLT (USED ON 6 INCH AND 9 INCH AUGERS)6 02957941 4 NUT7 01430750 4 BOLT8 01A0106E 6 INCH CUTTING EDGE KIT

01A0109E 9 INCH CUTTING EDGE KIT01A0112E 12 INCH CUTTING EDGE KIT01A0114E 14 INCH CUTTING EDGE KIT01A0118E 18 INCH CUTTING EDGE KIT01A0124E 24 INCH CUTTING EDGE KIT¤ BORING HEAD PARTS

9 00767686 1 9 INCH BORING HEAD AUGER00767687 12 INCH BORING HEAD AUGER

10 00767806 1 TOOTH, BORING HEAD, INNER11 00767807 2 TOOTH, BORING HEAD, OUTER W/BULGE12 01100130 1 FISHTAIL POINT13 37064H5C 3 BOLT14 00695100 3 NUT15 00764375 2 BOLT16 00001800 3 NUT17 00999418 BOLT

000245 1 BOLT¤ ROCK MOUNTAIN AUGER PARTS

18 00771166 1 9 INCH ROCKY MTN.00771103 12 INCH ROCKY MTN.

19 00771163 1 TOOTH, 9 INCH AUGER00771097 TOOTH, 12 INCH AUGER

20 00771102 1 PILOT BIT21 02886900 2 BOLT, AUGER TOOTH22 00001800 6 NUT23 00748823 2 BOLT24 00764375 2 BOLT

¤ AUGER EXTENSIONS25 01100740 7 INCH AUGER EXTENSION

01100760 14 INCH AUGER EXTENSIONSAFETY SHIELD

26 00768123 1 PLASTIC EXTENSION SHIELD



6 INCH AUGER ASSEMBLY Rev 05-07


00780367 - ASSY, AUGER 6" (WHOLEGOODS ONLY)5 00999418 3 HHCS 1/2-13UNC 3-1/2 PL56 00001800 5 LOCKNUT TLM 1/2 NC PLB7 02886900 2 CARR 1/2-13UNC 1-1/2 PL58 00780374 2 TOOTH, AUGER (40/50) AGGRESSOR

00780401 2 HARD SURFACED TOOTH (NOT SHOWN)00780460 2 CARBIDE TOOTH (NOT SHOWN)

9 00779803 1 BIT, PILOT (TF-350)00780402 1 HARD SURFACED BIT, PILOT(NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT





00780368 - ASSY, AUGER 9" (WHOLEGOODS ONLY)5 00999418 3 HHCS 1/2-13UNC 3-1/2 PL56 00001800 7 LOCKNUT TLM 1/2 NC PLB7 02886900 4 CARR 1/2-13UNC 1-1/2 PL58 00780374 4 TOOTH, AUGER (40/50) AGGRESSOR


9 00779803 1 BIT, PILOT (TF-350)00780402 1 HARD SURFACED BIT, PILOT (NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT





00780369 - ASSY, AUGER 12" (WHOLEGOODS ONLY)1 00001800 7 LOCKNUT TLM 1/2 NC PLB2 00999418 2 HHCS 1/2-13UNC 3-1/2 PL57 00752680 1 HHCS 1/2-13UNC X 4LG PL59 02886900 4 CARR 1/2-13UNC 1-1/2 PL510 00780374 4 TOOTH, AUGER (40/50) AGGRESSOR


11 00779803 1 BIT, PILOT (TF-350)00780402 1 HARD SURFACED BIT, PILOT (NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT






00780401 5 HARDSURFACED TOOTH (NOT SHOWN)00780460 5 CARBIDE TOOTH (NOT SHOWN)

11 00779803 1 BIT, PILOT (TF-350)00780402 1 HARDSURFACED BIT, PILOT (NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT







11 00779803 1 BIT, PILOT (TF-350)00780402 1 HARDSURFACED BIT, PILOT (NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT







11 00779803 1 BIT, PILOT (TF-350)00780402 1 HARDSURFACED BIT,PILOT (NOT SHOWN)00780461 1 CARBIDE TOOTH PILOT BIT (NOT SHOWN)00779803 1 BIT,STANDARD 2 PT. PILOT



AUGER ASSEMBLIES - EPHD



AUGER ASSEMBLIES - EPHD


¤ 6 INCH AUGER1 00768158 1 AUGER, 6 INCH - COMPLETE2 405622 1 SPIRAL AUGER TIP - SCREW-IN3 00767039 1 DECAL, AUGER4 000245 2 BOLT

00001200 2 NUT5 4050456 1 6 INCH CUTTING EDGE KIT - WELD ON


00001200 2 NUT10 3410406 1 9 INCH SERRATED CUTTING EDGE KIT - BOLT ON


00001200 2 NUT15 3410407 1 12 INCH SERRATED CUTTING EDGE KIT - BOLT ON



DRIVELINE ASSEMBLY - SHEAR BOLT 00773134



DRIVELINE ASSEMBLY - SHEAR BOLT 00773134


00773134 DRIVELINE ASSEMBLY1 00773137 1 COMPLETE COLLAR YOKE2 00773138 2 CROSS JOURN SET (15/16 IN DIA.)3 00773139 1 OUTER YOKE4 00773140 1 ROLL PIN5 00773141 1 OUTER TUBE6 00773142 1 INNER TUBE7 00773144 1 ROLL PIN8 00773143 1 INNER YOKE9 00773145 1 COMPLETE YOKE W/GREASE NIPPLE10 00773146 1 RETAINING COLLAR, OUTER11 00754330 6 BOLT12 00773147 1 RETAINING COLLAR, INNER13 00773148 1 COMPLETE GUARD14 00757144 1 COLLAR KIT15 00764386 1 GREASE FITTING16 00773150 1 OUTER GUARD HALF17 00773151 1 INNER GUARD HALF18 00773135 1 OUTER SHAFT W/GUARDING19 00773136 1 INNER SHAFT W/GUARDING20 01403020 1 SHEAR BOLT (USE GRADE 2 ONLY)21 00013901 1 NUT22 4407 1 COTTER PIN



DRIVELINE ASSY -HPHD, RPHD,SPHD & EPHD 00768283A Rev 05-07


00768283A - DRIVELINE, SP SER.40 PHD1 00764500A 1 COMPLET COLLAR YOKE2 00756231 2 CROSS & BEARING KIT SERIES 403 00759169 1 PIN ROLL 8mm X 60mm4 00759165 1 PIN ROLL INNER TUBE5 00768312A 1 YOKE, 1-1/4 BORE SP‘6 00764506 1 COLLAR-INNER-GUARD-RETAINER7 00754330 6 BOLT, NYLON - SAFETY SHIELD]8 00764507 1 COLLAR-OUTER-GUARD-RETAINER9 00768309 1 SHIELD, ASY, CMPLT10 00768306 1 SHAFT, ASY, OUTER W/SHIELD11 00768313 1 SHAFT, ASY, INNER W/SHIELD12 00774079 1 KIT,SLIDE COLLAR REPAIR13 7A61624 1 BOLT HHCS 3/8 NC 3 PL214 000640 1 LOCKNUT CLM 3/8 NC PLB15 5427 1 PIN-ROLL 1/4 X 1-1/2



DRIVELINE ASSEMBLY - RPHD,HPHD, & SPHD 00768283 Rev 05-04


00768283 DRIVELINE COMPLETE (SHEAR PIN)1 00768313 1 INNER SHAFT & SHIELD ASSEMBLY2 001465 1 GREASE FITTING3 00768312 1 SHEAR PIN YOKE4 00756231 2 CROSS & BEARING ASSEMBLY KIT5 00768295 1 INNER TUBE ASSEMBLY6 00768294 1 OUTER SHAFT & SHIELD ASSEMBLY7 00768293 1 OUTER TUBE ASSEMBLY8 00770391 1 TWIST COLLAR KIT9 00759170 1 YOKE ASSEMBLY10 00764507 1 OUTER TUBE BEARING11 00764506 1 INNER TUBE BEARING12 00775112 1 INNER HALF SHIELD ASSEMBLY13 00775113 1 OUTER HALF SHIELD ASSEMBLY14 00754330 6 LOCKING PIN15 00774569 1 SHEAR PIN KIT ( 6 PINS & LOCKS)16 5427 1 ROLL PIN



DRIVELINE ASSEMBLY- RADIAL CLUTCH (OPTIONAL) Rev 11-05


01430890 - DRIVELINE ASSEMBLY1 01430940 1 CLUTCH2 01430390 2 CROSS & BEARING KIT3 703623W 2 SPRING PIN4 8959 1 YOKE5 00775830 1 INNER TUBE6 00775805 1 OUTER TUBE7 8962 1 YOKE8 00775831 1 YOKE9 3216406 2 BEARING RING10 1416438 2 SCREW11 00775829 1 IMPLEMENT HALF COMPLETE12 00775828 1 TRACTOR HALF COMPLETE

00775832 1 OUTER SHIELD HALF COMPLETE00775808 1 INNER SHIELD HALF COMPLETE1416441 1 Q.D. KIT (IN ITEM 1) NOT SHOWN

13 00758068 1 HEXB 3/8 NC 2-1/2 PL814 00015800 1 NUT,TOPLOCK 3/8NC PLB15 420814 1 ROLL PIN, 1/4 X 1-3/4



DRIVELINE ASSY - SHEAR PIN EPHD - S/N 10761-11743


00777334 DRIVELINE COMPLETE (SHEAR PIN)1 00777360 1 INNER SHAFT & SHIELD ASSEMBLY2 001465 1 GREASE FITTING3 00768439 1 SHEAR PIN YOKE4 00768356 2 CROSS & BEARING ASSEMBLY KIT5 00777361 1 INNER TUBE ASSEMBLY6 00777362 1 OUTER SHAFT & SHIELD ASSEMBLY7 00777363 1 OUTER TUBE ASSEMBLY8 00770391 1 TWIST COLLAR KIT9 00768352 1 YOKE ASSEMBLY10 00777357 1 TUBE BEARING OUTER10A 00764506 1 SHIELD BEARING INNER11 00777359 1 INNER HALF SHIELD ASSEMBLY12 00777358 1 OUTER HALF SHIELD ASSEMBLY13 00774569 1 SHEAR PIN KIT (CONTAINS 6 PINS & LOCKS)14 5427 1 ROLL PIN



DRIVELINE ASSEMBLY - SHEAR PIN EPHD - S/N 10234 AND 10760


00768360A DRIVELINE COMPLETE (SHEAR PIN)1 00768438 1 INNER SHAFT & SHIELD ASSEMBLY2 001465 1 GREASE FITTING3 00768439 1 SHEAR PIN YOKE4 00768356 2 CROSS & BEARING ASSEMBLY KIT5 00768355 1 INNER TUBE ASSEMBLY6 00768354 1 OUTER SHAFT & SHIELD ASSEMBLY7 00768353 1 OUTER TUBE ASSEMBLY8 00770391 1 TWIST COLLAR KIT9 00768352 1 YOKE ASSEMBLY10 00768363 2 TUBE BEARING11 00768362 1 INNER HALF SHIELD ASSEMBLY12 00768361 1 OUTER HALF SHIELD ASSEMBLY13 00774569 1 SHEAR PIN KIT (CONTAINS 6 PINS & LOCKS)14 5427 1 ROLL PIN



DRIVELINE ASSEMBLY - SHEAR BOLT EPHD - S/N 10141 THROUGH 10233


00768360 1 DRIVELINE COMPLETE (SHEAR BOLT)1 00768358 1 INNER SHAFT & SHIELD ASSEMBLY2 001465 1 GREASE FITTING3 00768357 1 SHEAR BOLT YOKE4 00768356 2 CROSS & BEARING ASSEMBLY KIT5 00768355 1 INNER TUBE ASSEMBLY6 00768354 1 OUTER SHAFT & SHIELD ASSEMBLY7 00768353 1 OUTER TUBE ASSEMBLY8 00770391 1 TWIST COLLAR KIT9 00768352 1 YOKE ASSEMBLY10 00768363 2 TUBE BEARING11 00768362 1 INNER HALF SHIELD ASSEMBLY12 00768361 1 OUTER HALF SHIELD ASSEMBLY13 7A61622 1 SHEAR BOLT14 00015800 1 NUT15 20BH5012 1 ROLL PIN



GEARBOX ASSEMBLY WW 3.5 HD 3.5:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO RPHD & HPHD



GEARBOX ASSEMBLY WW 3.5 HD 3.5:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO RPHD & HPHD


1 01431320 1 HOUSING2 00755954 8 LOCKWASHER3 00758659 8 CAPSCREW4 00749508 2 PIPE PLUG5 01431250 1 HANGER SHAFT6 00606000 2 COTTER PIN7 01431390 1 HANGER CAP8 01431360 var. OUTPUT CAP GASKET 0.109 01431370 var. OUTPUT CAP GASKET 0.3010 01431310 1 BEARING SPACER11 01431280 1 RETAINING RING12 00770827 1 INPUT SEAL (1 PIECE SEAL)

00564200 1 SEAL (USE W/SEAL ADAPTER #01431290)13 01431400 1 11 TOOTH PINION & SHAFT14 00564800 2 BALL BEARING15 01431270 1 RETAINING RING16 00758674 1 OUTPUT SEAL17 01431330 1 OUTPUT SHAFT18 00755628 2 BEARING ASSEMBLY20 00770827 1 RETAINING RING21 00758667 1 GEAR ADJUSTING SHIM 0.3022 00758668 1 GEAR ADJUSTING SHIM 0.5023 01431350 1 OUTPUT GEAR 38 TOOTH24 01100550 1 RPHD-OUTPUT/AUGER SHIELD S/N 11341-12749 - HPHD-OUTPUT/AUGER

SHIELD S/N 11213-1235000762815 2 RPHD-OUTPUT/AUGER SHIELD S/N 12750 AND ABOVE - HPHD-OUTPUT/

AUGER SHIELD S/N 12351 AND ABOVE25 00035900 4 CAPSCREW26 00011700 4 LOCKWASHER27 00023500 4 FLATWASHER



GEARBOX ASSEMBLY WW4HD 4:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO SPHD



GEARBOX ASSEMBLY WW4HD 4:1 GEAR REDUCTION 1-1/4 SHAFT FOR RHINO SPHD


01101250 GEARBOX ASSEMBLY1 01431180 1 HOUSING2 00755954 8 LOCKWASHER3 00758659 8 CAPSCREW4 00749508 2 PIPE PLUG5 01431250 1 HANGER SHAFT6 00606000 2 COTTER PIN7 01431260 1 HANGER CAP8 01431220 var. HANGER CAP GASKET 0.10

01431230 var. HANGER CAP GASKET 0.2501431240 var. HANGER CAP GASKET 0.50

10 01431310 1 BEARING SPACER11 01431280 1 RETAINING RING12 00770827 1 INPUT SEAL13 01431300 1 11 TOOTH PINION & SHAFT14 00564800 2 BALL BEARING15 01431270 1 RETAINING RING16 00758674 1 OUTPUT SEAL17 01431190 1 OUTPUT SHAFT18 00769938 2 BEARING,TIMKEN 3021019 01431200 1 SPACER,OUTPUT BEARING20 00758660 1 RETAINING RING21 00758667 1 GEAR ADJUSTING SHIM 0.1222 00758668 1 GEAR ADJUSTING SHIM 0.0223 01431210 1 OUTPUT GEAR 44 TOOTH24 01100550 1 OUTPUT/AUGER SHIELD S/N 11159 - S/N 12820

00762815 2 OUTPUT/AUGER SHIELD S/N 12821 AND ABOVE25 00035900 4 CAPSCREW26 00011700 4 LOCKWASHER27 00023500 4 FLATWASHER



GEARBOX ASSEMBLY - EPHD



GEARBOX ASSEMBLY - EPHD


00770816 GEARBOX ASSEMBLY1 00770820 1 HOUSING2 00755954 8 LOCKWASHER3 00758659 8 CAPSCREW4 00749508 2 PIPE PLUG5 01431250 1 HANGER SHAFT6 00606000 2 COTTER PIN7 00770823 1 HANGER CAP8 00770824 var. HANGER CAP GASKET 0.309 00770825 var. HANGER CAP GASKET 0.2510 00770826 var. HANGER CAP GASKET 0.4011 01431310 1 BEARING SPACER12 01431280 1 RETAINING RING13 00770827 1 INPUT SEAL14 00770828 1 11 TOOTH PINION & SHAFT15 00564800 2 207K BALL BEARING16 00770829 1 RETAINING RING17 00758674 1 OUTPUT SEAL18 00770830 1 OUTPUT SHAFT19 00769938 2 TAPERED BEARING ASSEMBLY20 00770831 1 OUTPUT BEARING SPACER21 00758660 1 RETAINING RING22 00758667 var. GEAR ADJUSTING SHIM (0.30)23 00758668 var. GEAR ADJUSTING SHIM (0.50)24 00770822 1 33 TOOTH OUTPUT GEAR



CLUTCH - RADIAL PIN


01430940 RADIAL PIN CLUTCH ASSY1 1416422 1 RETAINING RING2 1416444 1 THRUST RING3 01431000 1 SEAL RING4 1416419 12 INNER SPRING5 1416418 24 OUTER SPRING6 1416417 24 CAM

0921000470 ref FLANGE KIT



DOWN PRESSURE KIT (EXTRA EQUIPMENT - USED W/SPHD ONLY) Rev 04-06


01A01150 DOWN PRESSURE KIT ASSY (WHOLEGOODS ONLY)1 02960460 1 STRAIGHT ADAPTER2 01430480 1 RELIEF VALVE3 61027400 1 ADAPTER4 01430500 1 HOSE5 02221600 1 ELBOW6 01430550 1 CYLINDER

00757290 1 SEAL REPAIR KIT (NOT SHOWN)7 01100150 1 UPPER CLAMP ASSEMBLY8 01100160 1 LOWER CLAMP ASSEMBLY9 02788400 2 BOLT GR510 01100170 1 CLEVIS PIN (1 INCH X 3-7/8 INCH)11 00755153 4 COTTER PIN12 0110019L 1 LEFT CYLINDER SUPPORT13 0110019R 1 RIGHT CYLINDER SUPPORT14 01100200 1 SPACER15 02014200 1 BOLT16 01100180 1 CLEVIS PIN17 00757291 1 PIPE PLUG18 00750596 1 BREATHER PLUG19 00001800 3 NUT20 01100020 ref YOKE PIN (SPHD ONLY)



HYDRAULIC DRIVE ASSEMBLY



HYDRAULIC DRIVE ASSEMBLY


07700020 HYDRAULIC POST HOLE DIGGER - LOW FLOW07700021 HYDRAULIC POST HOLE DIGGER - HIGH FLOW

1 00749130 2 BOLT2 00001300 2 LOCKWASHER3 00773920 1 BAR SPRING CLIP4 00011400 4 BOLT5 03101646 4 LOCKWASHER6 00011100 4 FLATWASHER7 00762815 2 SHIELD AUGER8 00773906 1 GEARBOX AUGER HYDRAULIC DRIVE9 00773410 1 COUPLING HYDRAULIC PHD10 00773908 1 MOTOR HYDRAULIC - LOW FLOW - A=7-5/8

00773907 1 MOTOR HYDRAULIC - HIGH FLOW - A=8-3/411 00773922 2 HOSE (PROVIDED W/CHAIN & BUCKET MOUNT OPTION)

02905600 2 HOSE (PROVIDED W/3-POINT HITCH KIT OPTION)12 00773923 2 STRAIGHT ADAPTER (PROVIDED W/ATTACHMENT OPTION)13 00768031 2 STRAIGHT ADAPTER (TRACTOR END)



GEARBOX ASSEMBLY - HYDRAULIC DRIVE Rev 05-05



GEARBOX ASSEMBLY - HYDRAULIC DRIVE Rev 05-05


00773906 GEARBOX ASSEMBLY - HYDRAULIC DRIVE1 00774181 1 HOUSING2 01430030 1 TOP CAP3 00774183 1 INPUT CAP4 01430070 1 GEAR, 35 TEETH5 00774184 1 INPUT PINION, 13 TEETH6 01430080 1 OUTPUT SHAFT7 01430010 1 MOUNTING SHAFT8 70048 1 BEARING CUP9 70049 1 BEARING CONE10 01600020 1 BEARING CUP11 01600030 1 BEARING CONE12 01600000 2 BEARING CUP13 01600010 2 BEARING CONE14 00774185 1 INPUT SEAL, 2 LIP15 00774186 1 OUTPUT SEAL, 2 LIP16 01430120 var. INPUT GASKET (0.50MM)17 01430040 var. TOP GASKET (0.10MM)18 01430050 var. TOP GASKET (0.15MM)19 01430060 var. TOP GASKET (0.50MM)20 00774190 var. INPUT GASKET (0.15MM)21 00774191 var. INPUT GASKET (0.10MM)22 00774192 1 KEY23 00000400 2 COTTER PIN24 00011400 4 BOLT25 00753642 6 BOLT26 03101646 10 LOCKWASHER27 00758654 1 PLUG, VENT28 00749508 1 PLUG



CLAMP MOUNT ASSEMBLY (OPTION)


1 00773921 1 WLDMT. SPRING CLAMP 4 INCH2 00773909 1 SPRING TENSION3 00773920 1 BAR SPRING CLIP4 00773923 2 ST. ADAPTER5 02905600 2 HOSE6 01A01020 1 BOOM CRANE7 00000400 2 PIN COTTER

01430010 1 MOUNTING SHAFT



DISPLAY STAND ASSEMBLY (OPTION) Rev 04-06


00771973 DISPLAY STAND ASSY (WHOLEGOODS ONLY)1 REF. 1 GEARBOX2 00771987 1 STAND WLDMT3 00010600 2 BOLT4 00767750 2 SUPPORT LEG5 00015800 2 NUT6 00762815 2 SHIELD, GEARBOX7 00011400 4 BOLT (HYDRAULIC PHD)

10119000 4 BOLT (REGULAR PHD)8 00011700 4 LOCKWASHER (REGULAR PHD)

03101646 4 LOCKWASHER (HYDRAULIC PHD)9 00023500 4 FLATWASHER (REGULAR PHD)

00011100 4 FLATWASHER (HYDRAULIC PHD)



UNIVERAL CHAIN MOUNT ASSEMBLY (OPTION)


00773911 UNIVERSAL CHAIN MOUNT ASSEMBLY1 00773229 1 UNIVERSAL BUCKET MOUNT2 00773914 4 CLEVIS LINK3 00773913 2 BINDER4 00773912 2 CHAIN5 00773226 1 MOUNT YOKE6 00760266 1 BOLT7 5JRC1490 1 NUT8 00773909 1 SPRING9 00773922 2 HOSE (NOT SHOWN)10 00773923 2 STRAIGHT ADAPTER (NOT SHOWN)11 00754881 4 BOLT12 02957941 4 NUT13 100761 4 RING14 00768031 2 ADAPTER, HYD, (NOT SHOWN)



BOLT-ON BUCKET MOUNT ASSEMBLY (OPTION)


00773910 UNIVERSAL CHAIN MOUNT ASSEMBLY1 00773233 1 BOLT-ON MOUNT2 00773234 1 BOLT-ON MOUNT PLATE3 00013300 4 BOLT4 00001800 4 LOCKNUT5 00773226 1 MOUNT YOKE6 00760266 1 BOLT7 5JRC1490 1 NUT8 00773909 1 SPRING9 00773922 2 HOSE (NOT SHOWN)10 00773923 2 STRAIGHT ADAPTER (NOT SHOWN)11 00768031 2 ADAPTER, HYD, (NOT SHOWN)



SAFETY DECALS


1 00776294 1 RPHD DECAL SHEET2 00776295 1 SPHD DECAL SHEET3 00776296 1 HPHD DECAL SHEET4 00776297 1 EPHD DECAL SHEET5 00776481 1 CANASTER MANUAL DECAL SHEET



LIMITED WARRANTY

1. LIMITED WARRANTIES1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal

purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)that the goods purchased are free from defects in material or workmanship.

1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to bedefective under normal use and service due to defects in material or workmanship.

1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, orlubricants, or which has served its normal life. This limited warranty does not apply to any part of any internalcombustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically foundin your Operator’s Manual.

1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of anynature on behalf of Manufacturer.

2. REMEDIES AND PROCEDURES.2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer

within 30 days of purchase.2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the

goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which theclaim is based.

2.03.Purchaser is responsible for returning the goods in question to the Dealer.2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and

service due to defects in material or workmanship, Manufacturer will:(a) Repair or replace the defective goods or part(s) or(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)

if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warrantyby Manufacturer.

The choice of remedy shall belong to Manufacturer.2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and

for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the trans-portation cost for the goods or part(s) from the Dealer to the designated factory.

3. LIMITATION OF LIABILITY.3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIESWITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESSFOR A PARTICULAR PURPOSE.3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR

USE OF THE GOODS.3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO

PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGECAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOTLIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM

THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THEABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGESINCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDERTHIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS

OCCURRED.4. MISCELLANEOUS.

4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,Texas.

4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shallbe deemed to be a waiver of any other term.

4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then theinvalidity of such provision shall not invalidate any other provisions herein.

4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.

KEEP FOR YOUR RECORDS

ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machineidentification when applying for warranty.

Servis-Rhino Implement Model _______________________________ Serial Number ________________________________

Date Purchased __________________________________________ Dealer ______________________________________

ATTENTION:READ YOUR OPERATOR'S MANUAL

SERVIS-RHINO

R


RHINO®

TO THE OWNER/OPERATOR/DEALER

To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions andthe Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easilyfind the information you need.

The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safetyrequirements of tractor operators:

REQUIRED OF THE OWNER:

1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and3. Ensure that each employee uses such Seatbelt while the tractor is moving; and4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected

area provided by the ROPS.

REQUIRED OF THE OPERATOR

1. Securely fasten seatbelt if the tractor has a ROPS.2. Where possible, avoid operating the tractor near ditches, embankments, and holes.3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.4. Stay off slopes too steep for safe operation.5. Watch where you are going - especially at row ends, on roads, and around trees.6. Do not permit others to ride.7. Operate the tractor smoothly - no jerky turns, starts, or stops.8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.9. When the tractor is stopped, set brakes securely and use park lock, if available.

Keep children away from danger all day, every day...

Equip tractors with rollover protection (ROPS) and keep all machineryguards in place...

Please work, drive, play and live each day with care and concern foryour safety and that of your family and fellow citizens.

Printed U.S.A.P/N 01430870PPost Hole Digger PL 05/04

01430870P---%20EPHD,RPHD,HPHD,SPHD%20PUB%2005-04%20Rev%2005-07.pdf

Documents

Transcript of 01430870P---%20EPHD,RPHD,HPHD,SPHD%20PUB%2005-04%20Rev%2005-07.pdf