008 Produkthandbuch 2018 transponder englisch...range of approx. 30 cm. For the best possible range,...

Tran

spon

der

LCN Transponder

157

Perfection.ISSENDORFF KG Magdeburger Str.3 30880 Laatzen/Germany Tel: +49 (0)5066 99 80 www.LCN.eu

Transponder

The LCN-UT module is a transponder evaluation system for integrating into the LCN system. It is clipped onto the I-Port connection of an intelligent bus module. A potential-free power supply is needed for operation.The delivery includes three antennae. The largest antenna has a range of approx. 30 cm. For the best possible range, use the LCN-UT to equilibrate the antenna.

Description:

By using the LCN-UT, a person-dependent access control system can be realised. This however, is not the only use as numerous other functions can also be activated.In small facilities the LCN module can immediately evaluate up to 16 different codes. In larger installations, people can be detected and registered and multiple time-dependent functions and macros can be carried out with visualisation systems such as the LCN-GVS.The LCN-UT especially lends itself for use in the medical and care professions where for instance people suffering from dementia are to be prevented from leaving buildings. For this purpose the antennae can be built into the floor.

Hardware equipment:

UT-module for flush mounting.

Three flat antennae in different sizes

Cable with plug for the I-Port connection to the intelligent bus module

Transponder card/credit card format

Transponder card as a keyring

Note:Only one antenna can be operated on the LCN-UT.Metal parts (construction steel, covers, bearer rings,...) or electrical interference (TV, monitors,...) affect the range.For special applications, antennae can be twisted individually, e.g. for installing them in doormats or in big picture frames.

LCN-UTTransponder unit incl. antenna for flush wall mounting (needs 16-30V=/~)

Function:

The LCN-UT module recognises transponder cards and so triggers freely programmable commands in the LCN system. It can be used for implementing personal access control.Up to 16 different transponder codes can be recognised and immedi-ately evaluated in the LCN receiver module. When used with visualisation software, more or less any number of people can be registered with individual commands being activated accordingly. Calling up any number of programmes individually for each card is also possible.

158


LCN-UTTransponder unit incl. antenna for flush wall mounting (needs 16-30V=/~)

D

LN

PE D

LN

PE

Tran

spon

der

Antenna

LCN-UPP

I

LCN-UTISSENDORFF KG

Rot/red

Grün/green Spannungsfrei installieren!

10-18V ~/=, P =1Wmax

GND

1 2 3 4 5 6

I-PortAnt. V

159

Dimensions:

Ø x H: 50mm x 20mm

50mm

43mm

Circuit diagram:

Assembly:

Module:

Antenna:

de-centralized installation in deep flush-mounted boxInstallation in floors or wall, e.g. plastered-in or covered with wallpaper

Technical Data:

10-18 =/~max. 1W bei 18V;typical 0,8W / 16V

EM-H 4001, 4002, 4102, IP 20

Connection:Power supply:Power capacity:

Supported card system: Safety classification:

Technical Data LCN-Flat Antenna:0,4mm

Ø 245 mm exteriorØ 200 mm insideca. 28 cm with LCN-ZTK

Ø 123 mm exteriorØ 86 mm interiorca. 20 cm with LCN-ZTK

Ø 50 mm exterior

Ca. 9 cm with LCN-ZTK

120 mm (not extendable)

-10°C to +40°CMax . 80% rel. No condensation

Stationary installation acording to VDE632 and VDE637

IP 20

Depth

Size (Antenna large)

Range:

Size (Antenna medium)

Range

Size (Antenna small)

Range:

Connection cable:

General details:Operating tempHumidity

Enviromental conditions

Safety classification:


The LCN-ULT is a universal transponder reading device for installing in flush mounted wall-boxes. It recognises all LCN- transponders and passive transponder types of other manufacturers, Junghans transponder watches and most transponder car keys. Firmware updates are available for any future transponder types (should this prove necessary).

Description:

The LCN-ULT is suited for indoor and outdoor use and intended for fitting in a 68mm flush mounted socket.It is for reading passive transponders at a distance of up to 7cm.Access control, clocking systems and automatic building functions can all be set with the reading device. The reading device comes with a white or silver-grey plastic cover. The 5 metre long connection cable is already fitted.The LCN-ULT can be connected to the I-Port of any LCN module da-ting from 2009.

Hardware equipment:

LCN-ULT reading device for transponderLCN-ULT master cardLCN-IV I-Port extensionLCN-NU16 power supplyTorx-Bit TX-10Torx fixing screwInstallation instructions

Note:For more detailed information please refer to the installation instructions.

Universal transponder readerLCN-ULT

Transponder

Function:When the transponder is within reading distance of the LCN-ULT, the individual transponder-ID is transmitted to the I-Port of the connected LCN module and evaluated.The LCN-ULT remains unconfigured on delivery. Only needing to be done once, the necessary transponder type can be set using the mas-ter card so that only corresponding transponder data from the same system can be read.Every transponder can be given individual authorisation with the LCN-PRO software.

160


Universal transponder readerLCN-ULT Tr

ansp

onde

r

80mm

80mm

Dimensions:Cover: (L x H): 80 mm x 80 mmFixing Height: 11,7 mmSocket Depth: 27,7 mmConnection Cable: 5 m

Assembly:

Frame:

Technical data

161

de-centralized installation in deep flush-mounted box

Available in white and silver

Circuit diagram:

Reading Device LCN-ULT

9V DC (stable)

max. 110mA

o o-10 C to +40 Cmax. 80% rel., Non condensing

stationary installation according to VDE

IP 20

120 kHz – 140 kHz

Duo-LED blue/Red

0,2 cm – 7 cm (Dependent on transponder type instal-lation location of antenna)

LCN-ZTK; LCN-ZTS; LCN-AT2; EM-H 4001/ 4002/ 4102/ 4402/ 4050/ 4150/ 4450, Megamos, ATMEL, Philips, Sokymat Nova, TexasInstruments, Temic, NXP, further systems on request

o o-30 C to +70 CStationary installation to VDE 632 and VDE 637IP 65In- and outdoorsASA (weather and UV re-sistance)85 g

Connection:Supply Voltage via LCN-NULT:

Current

General details:Operating temperature:Humidity:

Environmental conditions:


Technical data LCN-ULT:LF-Magnetic feld:

Rearlighting:

Reading Distance:

Supported Card Systems:

General details:Opperation Temp:Enviromental Conditions:

Safety classification:Application Area:Material:

Weight without Cable:

ca. 5m

LN

Power on

LCN-NULTISSENDORFF KG

85-264VAC50/60Hz, P 2,5Wmax

Schwarz/blackBlau/blueLED

ULTbr we gn ge

I-Anschl.

I-port

LCN-bus modules

I

D

LN

PE D

LN

PE


The LCN-ZTK is a transponder card in credit-card format for use with LCN-UT.

Description:

The LCN-UT module recognises the LCN-ZTK transponder cards and so triggers freely programmable commands in the LCN system.

Transponder in bank card formatLCN-ZTK

Transponder

54m

m

86mm D

LN

PE

LCN-UT

LCN Bus Modulewith I-Port

Antenna

LCN-ZTK

162

Circuit diagram: Dimensions:

(L x W x H): 54 mm x 86 mm x 0,8 mm

PF 22

EM H 4002

125 kHz

PVC

-45°C to +70°C

-50°C to +70°C

IP 68

Card type:

Compatible card system:

Frequency:

Material:

Operating temperature:

Storage temperature:


Technical Data:


Transponder as a key-ringLCN-ZTS Tr

ansp

onde

r

The LCN-ZTS is a key-ring with an integrated transponder but has slightly less range than the transponder-card version.

Description:

The LCN-UT module recognises the LCN-ZTS transponder and triggers freely progammable commands in the LCN system.

30mm

55m

m

D

LN

PE

LCN-UT Antenna

LCN-ZTS

163

Circuit diagram:

LCN Bus Modulewith I-Port

Dimensions:

(L x W x H):

Technical Data:

TAG SAIL B

EM H 4002

125 kHz

ABS

-40°C to +85°C

-50°C to +70°C

IP 68

Card type:

Compatible card system:

Frequency:

Material:

Operating temperature:

Storage temperature:


30mm x 55mm x 7mm


The active reader LCN-ATW evaluates active transponders at a distance of up to 4m.In its typical application, personnel who are to be detected carry active transponders around with them in different forms.Simply by pressing a button on the transponder handset LCN-AT2, which is supplied, a range of up to 50m can be achieved.

Description:

The LCN-ATW offers access control at a greater distance which enables greater convenience than passive transponders.Doors can be opened fully automatically rendering conventional keys superfluous.In comparison to other keyless entry systems such as finger-print sensors etc., the active transponder is entirely hands-free.The LCN-ATW can be extended and used as a tracking system, registering the exact location of personnel. The transponders are available in different shapes and sizes including buttons for remote control functions which can be used in hotels for example. In such an instance, hotel guests can call the waiter using their room key whilst also transmitting their name and table number in one fell swoop.

Hardware equipment:

Active reading device (IP67) with antenna in cover

Including LCN-SHS +LCN-NH24 +LCN-IVH

LCN-AT2 Hand-held transponder transmitter with 2 buttons.

Information to transponder-system:

Passive transponder systems (LCN-ULT) are of particularly good value. Not requiring any batteries, they can be applied in more compact versions such as credit-cards.Disadvantages:1:Limited range. 2: The range is dependent on the angle of the card to the antenna. 3: Only one transponder can be registered at a time; the transponders must enter the antenna field in succession.Active transponders require a battery which needs to be changed every 2 years. In return they have many advantages:1: Containing a built-in antenna, the LCN-ATW has a max. range of 4m and can be extended with an external antenna if necessary. 2: The small transponder has 3 internal antennae so that the reading device can receive its signal from any position. 3:Thanks to the intelligent anti-collision function, up to 10 transponders can be registered at the same time by the reading device.

Transponder

Function:

If a person approaches the antenna (detection field can be adjusted using rotary potentiometer), the person's active transponder is activated and transmits their ID. The LCN-ATW then transmits this ID number to the I-Port of a bus- module. Numerous transponders in the field are then buffered in the reading device's memory and sent in sequence to the I-Port. The transponders are available in different shapes and sizes including buttons for remote control application (LCN-AT2).

A transponder is automatically activated as soon as it enters the reading device's detection field.Transponders fitted with one or two buttons send wireless commands to the reading device (LCN-ATW) when the buttons are pressed without having to be in the antenna's detection field (active transmission). Active transmission (push button) has a max. range of 50m in open surroundings.

For status monitoring there are two LEDs (green/red).

Active transponder system for wall mountingLCN-ATW

164


Active transponder system for wall mountingLCN-ATW Tr

ansp

onde

r

250mm

160mm

D

LN

PE D

LN

PE

LCN-AT2LCN-ATW

165

Dimensions:

Case size (L x W x H): 160 mm x 250 mm x 90 mm

ScrewsAssembly:

Circuit diagram:

Technical data230V AC ±15%, 50/60Hz(110V AC ±15% type available)

8W

125 kHz

Adjustable 0,5 to 4m

868 MHz (free of charge ISM Band)

50m in open areas

Unidirectional (LF & HF)

o o-20 C to +50 CStationary installation according to VDE632,VDE637

IP 65Outside/Inside mountingLight gray RAL 7035Polycarbonate

Connections:Supply voltage:

Input power:

LF magnetic feld:

Distance (LF, passive transmission.):HF (high frequency):

Distance (HF, aktive transmission):Communication type:

General details:Operating Temp:Enviromental conditions:

Safety classification:Application:Colour: Material:


The LCN-AT2 is an active transponder for the active transponder sys-tem LCN-ATW.With its 2 extra buttons it can also be used as a remote control within the LCN system .

Description:

For use in conjunction with the active transponder system LCN-ATW for automatic building functions such as opening doors, clocking sys-tems and access control.Using the integrated hand-held sender, commands can be sent to the LCN system at a range of up to 50m.

Hardware equipment:

Transponder for the transponder system LCN-ATW2 Buttons for manual triggering of LCN commandsEasy to handle shape for use on a key ring

Hand-held transponder transmitter with 2 buttonsLCN-AT2

Transponder

Function:

The LCN-AT2 is automatically activated as soon as it enters the LCN-ATW detection field. Irrespective of this, it can also send commands via its 2 buttons to the antenna without having to be in the antenna's detection field (active transmission).

For status monitoring there are 2 LEDs (green/Red).

166


Hand-held transponder transmitter with 2 buttonsLCN-AT2

Technical data

Circuit diagram:

Tran

spon

der

Dimensions

(L x W x H): 47mm X 63mm X 17mm

47mm

63mm

D

LN

PE D

LN

PE

LCN-AT2LCN-ATW

LF-Technique, low frequency

Low frequency magnetic field (LF): 125 kHzRange: max. 4mCommunication type: unidirectionalReception characteristics: three dimensional

HF-Technique, high-frequency

Radio frequency (HF): 868MHz UHFRange: up to 50mCommunication type: bidirectional

Power supply

Supply voltage: 3 Volt DCBattery: Lithium cell 2450

Operating temp: 40 °C ... + 85 °C

Lifetime: Min. 2years ,typical 4 –5 years

Safety classification: IP 67Colour: blackMaterial: PA6 GF10 GK20Weight: 29 g

167


Transponder

168


The LCN-GT2T is a transponder-reader with integrated infrared receiver, wo capacitive sensor keys and Corona® light.

It is mounted on a flush-mounted box using the supplied mounting plate and firmly anchored with a slide.

The connection is made via the I-connection of any LCN module from version 17070A (July 2013).

Supported are 13.561MHz NFC transponders of the type e.g. Mifare, Legic, etc. (ISO14443-A (type 1,2,4) and ISO15693 (type 5).

Description:

The two capacitive sensor surfaces are arranged behind a 5mm (3mm) thick surface. A light touch of the surface is enough to trigger functions.

A status LED integrated in each sensor surface provides information on the current status of any actuators or sensors in the building. Four states are possible.

The integrated NFC reader recognizes/reads the cards when they are held directly in front of the glass pane. The code is transferred from the module to the LCN bus. The 8-digit code can be processed directly in the module ("small" access control) or with the LCN-GVS ("large" access control).

In addition, the LCN-GT2T offers a Corona® light with white LEDs for wall illumination and elegant backlighting of the keys. This allows the LCN-GT2T to be operated comfortably even in low ambient light.

The individual inscriptions for the LCN-GT2T are transferred to a foil or paper and placed behind the glass surface. The label can be recreated at any time, so that changes in the key assignment are no problem.

:

The LCN-GT2T is designed for installation in dry interiors. It can be used for all switching, regulating and control tasks as well as for ac-cess control and time recording in the LCN bus.

Hardware equipment:

LCN-GT2TLCN-NUIMounting panelLabelling foilInstallation guide

Note:Attention: Plug in voltage-free!Switch off the power supply LCN-NUI before plugging in the LCN-GT2T. Please refer to the installation instructions for detailed information.

Field of application

Functionality:

The sensor surfaces of the LCN-GT2T react capacitively to contact with the glass surface. Depending on the duration of contact, a corresponding LCN control command (Hit, Hold and Release) is sent. The control command is transmitted to the I connection of an LCN module via the mounting plate included in the scope of delivery.

The 2 status LEDs in the sensor surfaces are individually controlled via the I connection and configured via LCN-PRO (on, off, flashing, flickering).

The transponder function is triggered via NFC standard (Mifare, Legic etc.) e.g. via transponder card, smartphone or other compatible peripherals.The integrated infrared receiver (LCN-RR) offers, e.g. via remote control, another possibility for remote triggering of functions.

Models:

LCN-GT2T• Size: 90mm x 90mm

Colour: white LCN-GT2TWblack LCN-GT2TBchampagne LCN-GT2TC

LCN-GTS2T• Size: 75mm x 75mm

Colour: white LCN-GTS2TWblack LCN-GTS2TBchampagne LCN-GTS2TC

LCN-GT2T / LCN-GTS2TTransponder-reader with two capacitive sensor keys and Corona light®

Design example

Product availablein Q4/2018

Tran

spon

der

169


LCN-GT2T / LCN-GTS2TTechnical data

Dimensions:(W x L x H)

Assembly: By means of mounting plate on flush-mounted box

90m

m

90mm 13mm

75m

m

LCN-GT2T LCN-GTS2T

75mm

• • • • ••• •

LCN-GT2T:90mm x 90mm x 13mm(5mm glass thicknessLCN-GTS2T :75mm x 75mm x 11mm (3mm glass thickness)

90m

m

11mm

75m

m

®Transponder-reader with two capacitive sensor keys and Corona light

Frame: Available in the colours black, white or champagne, special colours upon your request

Circuit diagram

D

LN

PE D

LN

PE

ConnectionPower supply: via LCN-module + LCN-NUILCN-connection: I-connection

Tasten:Type: two capacitive sensor surfaces with

status LED behind glassFunction: HIT / HOLD / RELEASE Labeling: via changeable foil

LEDs:Status-LEDs: two red LEDs for displaying LCN

status messages, FUNCTION: OFF / FLASHING / FLICKERING / ON

keypad background LEDs: LEDs®Corona -LED: White Corona® LEDs can be

controlled via the "LED brightness" command

reading distance: 0,2cm - 7cm (depending on transponder type and installation location of the antenna)

Supported card system: Mifare, Legic, Type (ISO14443-A (Typ 1,2,4) and ISO15693 (Typ 5)).

General data:Operating temperature: -10°C to +40°CHumidity: max. 80% rel., non-condensingInstallation: stationary installation according to

VDE 632, VDE 637Safety classifications IP 40

LCN bus modulewith I-connection

power supplyLCN-NUI

I II

LCN-GT2T

I

two capacitive sensor surfaces behind glasstwo status LEDsNFC transponder-readerintegrated infrared receiverincl. white Corona®-light wreathincl. button backlightingindividual design of the keys with inlayoperation at the I-connection

Transponder

170


008 Produkthandbuch 2018 transponder englisch...range of approx. 30 cm. For the best possible range,...

Documents

Transcript of 008 Produkthandbuch 2018 transponder englisch...range of approx. 30 cm. For the best possible range,...