• FLOOR MOUNTED JIB CRANES • PORTABLE JIB ... · PDF file• FLOOR MOUNTED JIB...

1377 Kimberly Dr., Neenah, WI 54956 (920)-722-0101 FAX (920)-722-5260

www.contrx.com

FESTOON SYSTEMS, CRANE RAILS, CRANE CONTROLS,CRANE REPAIR & REBUILDING, MACHINING SERVICE6-23-2016

• FLOOR MOUNTED JIB CRANES• PORTABLE JIB CRANES• WORKSTATION JIB CRANES• WALL MOUNTED JIB CRANES• GANTRY CRANES• FORKLIFT JIBS• BELOW THE HOOK EQUIPMENT• BRIDGE CRANES

CONTRX INDUSTRIES1377 Kimberly Drive

Neenah, WI 54956-1642Phone (920) 722-0101

Fax (920) 725-1394www.contrx.com

Optional top entry electrical collectorcan be attached to most 360° revolvingjib cranes. No special parts needed.

Sleeve mount base(Optional)

Optional factory installedbottom entry electrical

collector brings power inthrough the column assembly.

Optional motorizedboom rotation

Foundation mount base(Optional)

Bolt-type base plate(Standard)

10-22-02

BeamAssembly

ColumnAssembly

HeadAssembly

SELF-SUPPORTING FLOOR CRANESNEED MINIMUM HEAD ROOM.

HEAVY DUTY JIB CRANES- 360° ROTATION -

"A" SERIES

FLOOR MOUNTED

Contrx "A"- jibs are ruggedly constructed for industrialuse and years of trouble-free service. Complete boomassembly is supported by an adjustable column rollerassembly to permit field adjustment and insure evenpressure of rollers on pipe. The boom is constructed

using an I shaped rolled steel beam. The headassembly has two heavy side plates with reinforcing

steel to create a rigid pivoting connection between thebeam assembly and the column assembly. Standardjibs up to 20' span and 20' height under boom. Contrx

specializes in modifications and custom designs.

1377 Kimberly DriveNeenah, WI 54956-1642

Office (920) 722-0101Fax (920) 725-1394

TrolleyEnd Stops

EndstopMountingHardware

Boom Assembly

Lower RollerAssembly

Anchor BoltHardware

Boom Mounting Hardware(see Note 2)

Head Assembly

Main Bearing(see Note 1)

Upper Bearing Pin

Column Assembly

Column Gussets

Jib Base Plate

Boom LevelingAdjustment Nuts (8)

LowerRoller (2)

Thrust Washer (4)The following models have (2):-4000# cap. with longer than 16'-0" boom--6000# cap. with longer than 10'-0" boom--10,000# cap. all boom lengths-

Lock Pin (2)

Roller Shaft (2)

Concrete Footing and'L' Anchor Bolts(by customer) Refer to:FLOOR MOUNT 'A' JIB drawing number

________________

Main Bearing Cup(pressed in at factory)

Boom MountingHardware

Beam Plate

Trolley Stops(field drill boom)

www.contrx.comBoom Length

DWG NO

'A' Jib Assembly Detail

A-1005-A8-16-02 Not to scale

Note 1:Complete bearing assembly factory installedin the Boom Assembly on the following models:-4000# cap. with longer than 16'-0" boom--6000# cap. with longer than 10'-0" boom--all 10,000# cap. A-jibs-

Note 2:Beveled washers are to be used on taperedflange beams only.

Note 3: For orders with similar multiple cranes,look for markings on the inside of the beamplate and the matching face of the headassembly. This will insure the correct partsare matched up.

16"16"

16"16"16"

16"16"

23-3/4"23-3/4"

16"16"

23-3/4"

23-7/8"23-7/8"

21-1/8"23-7/8"

23-7/8"23-7/8"

24-1/2"

4'4'

4'4'4'

4'4'

4'4'

4'4'

4'

4'4'

4'4'

4'4'

4'

7'7'

7'7'8'

7'7'

8'8'

7'7'

8'

9'9'

9'9'

10'10'

10'

17-3/8"17-3/8"

17-3/8"17-3/8"17-3/8"

17-3/8"17-3/8"

21-3/8" **21-3/8"

17-3/8"21-3/8"

21-1/2"

24-1/2"21-1/2"

24-1/2"24-1/2"

29-1/2"24-1/2"

29-1/2"

42"42"

42"48"48"

42"42"

48"48"

42"48"

48"

54"54"

66"66"

72"66"

72"

38"38"

38"44"44"

38"38"

44"44"

38"44"

44"

50"50"

60"60"

66"60"

66"

22002120

196023422422

19802057

34393315

19162716

3759

49804434

46274983

60865135

6843

A21020A21018

A31014A31016A31018

A41012A41014

A41020A41018

A61010A61012

A61016

A61020A61018

A101012A101014

A101018A101016

A101020

24222229

206924672547

21062182

35803456

20412857

3968

52314642

48785234

64015386

7158

A21220A21218

A31214A31216A31218

A41212A41214

A41220A41218

A61210A61212

A61216

A61220A61218

A101212A101214

A101218A101216

A101220

25472467

230725932742

22312307

43373597

21662998

4176

54824850

55785933

67166085

7473

A21420A21418

A31414A31416A31418

A41412A41414

A41420**A41418

A61410A61412

A61416

A61420A61418

A101412A101414

A101418A101416

A101420

10'

12'

12'

12'

14'

14'

14'

16'

16'

16'

18'

18'

18'

18'

18'

20'

20'

20'

20'

2,0002,000

3,0003,0003,000

4,0004,000

4,0004,000

6,0006,000

6,000

6,0006,000

10,00010,000

10,00010,000

10,000

W12W12

W12W12W12

W12W12

W12W12

W12W12

W12

W12W12

W12W12

W12W12

W12

7"7"

7"7"7"

7"7"

7"7"

7"7"

7"

9"9"

8-1/4"9"

9"9"

9"

1-1-11

8'

21"

21"

21"

21-1/8"21-1/8"

4'

4'

4'

4'4'

8'

8'

8'

9'9'

17-3/8"

17-3/8"

21-3/8"

21-1/2"21-1/2"

48"

48"

48"

60"60"

44"

44"

44"

56"56"

2877

2649

3075

38263962

A31020

A41016

A61014

A10108A101010

3002

2774

3216

40344170

A31220

A41216

A61214

A10128A101210

3197

2969

3357

44954631

A31420

A41416

A61414

A10148A10141010'

14'

16'

20'3,000

4,000

6,000

10,00010,000

W12

W12

W12

W12W12

6-1/2"

6-1/2"

6-1/2"

8-1/4"8-1/4"

8'

12-3/8"12-3/8"

12-3/8"

12-3/8"

16"

12-3/8"

4'4'

4'

4'

4'

3'

6'7'

6'

6'

7'

5'

12-3/8"12-3/8"

12-3/8"

12-3/8"

17-3/8"

17-3/8"

36"36"

42"

36"

42"

36"

32"32"

38"

32"

38"

32"

15021615

1588

1435

1836

1888

A21014A21016

A31012

A41010

A6108

A11020

16651725

1697

1545

1961

1997

A21214A21216

A31212

A41210

A6128

A11220

17741834

1806

1654

2086

2106

A21414A21416

A31412

A41410

A6148

A11420

10'

12'

14'16'

20'

2,0002,000

3,000

4,000

6,000

1,000

W12W12

W12

W12

W12

W12

6-1/2"6-1/2"

6-1/2"

6-1/2"

7"

6-1/2"

8'

8'

10-3/8"10-3/8"

10-3/8"

10-3/8"

10-3/8"

10-3/8"

3'3'

4'

4'

4'

4'

5'5'

6'

6'

6'

6'

12-3/8"12-3/8"

12-3/8"

12-3/8"

12-3/8"

12-3/8"

36"36"

36"

36"

36"

36"

32"32"

32"

32"

32"

32"

14921543

1388

1335

1337

1283

A11016A11018

A21012

A31010

A4108

A3108

15911642

1487

1434

1446

1382

A11216A11218

A21212

A31210

A4128

A3128

16901815

1586

1607

1555

1482

A11416A11418

A21412

A31410

A4148

A314810'

12'

16'18'1,000

1,000

2,000

3,000

4,000

3,000

W12W12

W12

W12

W12

W12

5-3/4"5-3/4"

5-3/4"

5-3/4"

5-3/4"

5-3/4"

"S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam. * Model A21410 has an 'F' dimension of 12-1/4".** Model A41420 has an 'F' dimension of 21-1/2"


Phone (920) 722-0101Fax (920) 725-1394

FLOOR MOUNTED 'A' SERIESJIB CRANE SPECIFICATIONS

www.contrx.com

8'

8'D

8"8"8"

8"8"

3'3'3'

4'4'

3'E

4'4'5'

5'5'

4'W

10-1/4"F

10-1/4"10-1/4"12-1/4"

10-1/4" *10-1/4"

24"24"

24"BD

36"36"

36"

20"20"

20"BC

32"32"

32"

670LBS. LBS.LBS.

822858

1081

950913

MODEL MODELMODELA1108A11010A11012A11014

A21010A2108

715878914

1137

1006969

A1128A11210A11212A11214

A21210A2128

760934970

1499

14261025

A1148A11410A11412A11414

A21410*A2148

A

10'

10'12'14'

6"

B = 12' HT. B = 14' HT.B = 10' HT.

1,0001,0001,0001,000

2,0002,000

BEAMTYPE

BOLTHOLES

S6S6S12

S12S12

S6

CAP.(LBS.) FW

4"4"

4"4"

4"3-3/8"

DIMENSIONS

W

B

BOOM ASSEMBLYFIELD MOUNT

D

2"

HEADASSEMBLY

COLUMNASSEMBLY

FW

LOWERROLLERASSEMBLY

3/4" DIA. REINFORCING RODS6" FROM TOP & BOTTOMAPPROX. 12" ON CENTERBOTH WAYS

BOLT CIRCLEDIAMETER

(BC)

BASE PLATEDIAMETER

(BD)

F A

WW

1-1/4" DIA.6 PLACES

1-1/4" DIA.12 PLACES

60° 30°

BASE DETAILHOLES EQUALLY SPACED

E

Jib Crane Accessories:- Anchor Bolt Kits- Tagline Kits- Templates (Paper & Plywood)- Hoists & Trolleys (Electric & Manual)- Motorized Rotation

4"

BASE

3/4 E

CAP. (LBS)

DIMENSIONS BOLT HOLES

BEAM TYPE

B=16’ B=18’ B=20’

A D FW E W F BD BC LBS. MODEL LBS. MODEL LBS. MODEL 1,000 8’ 6” 3-3/8” 3’ 4’ 10-1/4” 24” 20” 6 S 804 A1168 849 A1188 894 A1208 1,000 10’ 8” 4” 3’ 4’ 12-1/4” 36” 32” 12 S 1525 A11610 1624 A11810 1723 A12010

1,000 12’ 8” 4”

3’ 4’ 12-1/4”

36” 32” 12 S 1562 A11612 1661 A11812

10-3/8” 5-3/4” 12-3/8” W 1987 A12012

1,000 14’ 8” 4”

3’ 5’ 12-1/4”

36” 32” 12 S 1598 A11614

10-3/8” 5-3/4” 12-3/8” W 1930 A11814 2039 A12014 1,000 16’ 10-3/8” 5-3/4” 3’ 5’ 12-3/8” 36” 32” 12 W 1872 A11616 1979 A11816 2091 A12016

1,000 18’ 10-3/8” 5-3/4”

3’ 5’ 12-3/8” 36” 32”

12 W 1924 A11618

12-3/8” 6-1/2” 17-3/8” 42” 38” 2518 11818 2643 A12018 1,000 20’ 12-3/8” 6-1/2” 3’ 5’ 17-3/8” 42” 38” 12 W 2453 A11620 2578 A11820 2703 A12020

2,000 8’ 8” 4” 4’ 5’ 12-1/4” 36” 32” 12 S 1488 A2168 1587 A2188 1686 A2208

2,000 10’ 8” 4”

4’ 5’ 12-1/4”

36” 32” 12 S 1525 A21610

10-3/8” 5-3/4” 12-3/8” W 1825 A21810 1934 A22010

2,000 12’ 10-3/8” 5-3/4”

4’ 6’ 12-3/8” 36” 32”

12 W 1769 A21612

12-3/8” 6-1/2” 17-3/8” 42” 38” 2338 A21812 2463 A22012

2,000 14’ 12-3/8” 6-1/2”

4’ 6’ 17-3/8” 42” 38”

12 W 2273 A21614 2398 A21814

16” 7” 48” 44” 3006 A22014

2,000 16’ 16” 7” 4’ 7’ 17-3/8” 42” 38”

12 W 2513 A21616

48” 44” 2945 A21816 3086 A22016

2,000 18’ 16” 7”

4’ 7’ 17-3/8”

48” 44” 12 W 2884 A21618 3025 A21818

21” 6-1/2” 21-1/2” 4732 A22018

2,000 20’ 16” 7”

4’ 7’ 17-3/8”

48” 44” 12 W 2964 A21620 3105 A21820

21” 6-1/2” 21-1/2” 4846 A22020

3,000 8’ 10-3/8” 5-3/4” 4’ 6’ 12-3/8” 36” 32” 12 W 1581 A3168 1680 A3188 1779 A3208

3,000 10’ 10-3/8” 5-3/4”

4’ 6’ 12-3/8” 36” 32”

12 W 1716 A31610 1825 A31810

12-3/8” 6-1/2” 17-3/8” 42” 38” 2403 A32010

3,000 12’ 12-3/8” 6-1/2”

4’ 6’ 17-3/8” 42” 38”

12 W 2213 A31612

16” 7” 48” 44” 2788 A31812 2929 A32012 3,000 14’ 16” 7” 4’ 7’ 17-3/8” 48” 44” 12 W 2724 A31614 2865 A31814 3006 A32014

3,000 16’ 16” 7”

4’ 7’ 17-3/8”

48” 44” 12 W 2804 A31616 2945 A31816

21” 6-1/2” 21-1/2” 4618 A32016

3,000 18’ 16” 7”

4’ 8’ 17-3/8”

48” 44” 12 W 2884 A31618 3025 31818

21” 6-1/2” 21-1/2” 4732 A32018 3,000 20’ 21” 6-1/2” 4’ 8’ 21-1/2” 48” 44” 12 W 4430 A31620 4638 A31820 5305 A32020

4,000 8’ 10-3/8” 5-3/4” 4’ 6’ 12-3/8” 36” 32” 12 W 1664 A4168 1773 A4188 1882 A4208

4,000 10’ 12-3/8” 6-1/2” 4’ 6’ 12-3/8” 36” 32” 12 W 1763 A41610 17-3/8” 42” 38” 12 W 2278 A41810 2403 A42010

4,000 12’ 16” 7” 4’ 7’ 17-3/8” 42” 38”

12 W 2354 A41612

21-3/8” 48” 44” 3255 A41812 3396 A42012 4,000 14’ 16” 7” 4’ 7’ 21-3/8” 48” 44” 12 W 3194 A41614 3335 A41814 3476 A42014

4,000 16’ 23-3/4” 7” 4’ 8’ 21-3/8”

48” 44” 12 W 3614 A41616

21-1/2” 4505 A41816 4778 A42016

4,000 18’ 23-3/4” 7” 4’ 8’ 21-3/8”

48” 44” 12 W 3738 A41618

21-1/2” 4629 A41818 4902 A42018

4,000 20’ 23-3/4” 7” 4’ 8’ 21-1/2” 48” 44”

12 W 4545 A41620

24-1/2” 54” 50” 5643 A41820 5894 A42020

6,000 8’ 16” 7” 4’ 7’ 17-3/8” 42” 38” 12 W 2212 A6168 2337 A6188 2462 A6208 6,000 10’ 16” 7” 4’ 7’ 17-3/8” 42” 38” 12 W 2292 A61610 2417 A61810 2542 A62010

6,000 12’ 16” 7”

4’ 7’ 21-3/8” 48” 44”

12 W 3139 A61612 3281 A61812

21” 6-1/2” 8’ 21-1/2” 54” 50” 4747 A62012

6,000 14’ 21” 6-1/2” 4’ 8’ 21-3/8” 48” 44”

12 W 3498 A61614

21-1/2” 54” 50” 4653 A61814 4861 A62014

6,000 16’ 23-3/4” 7”

4’ 8’ 21-1/2” 48” 44”

12 W 4384 A61616

23-7/8” 9” 24-1/2” 54” 50” 5680 A61816 5931 A62016 6,000 18’ 23-7/8” 9” 4’ 9’ 24-1/2” 54” 50” 12 W 5581 A61618 5832 A61818 6083 A62018 6,000 20’ 23-7/8” 9” 4’ 9’ 24-1/2” 54” 50” 12 W 5733 A61620 5984 A61820 6235 A62020

10,000 8’ 21-1/8” 8-1/4” 4’ 9’ 21-3/8” 60” 56” 12 W 4746 A10168 4997 A10188 5248 A10208 10,000 10’ 21-1/8” 8-1/4” 4’ 9’ 21-1/2” 60” 56” 12 W 4882 A101610 5133 A101810 5384 A102010 10,000 12’ 21-1/8” 8-1/4” 4’ 9’ 24-1/2” 66” 60” 12 W 5892 A101612 6207 A101812 6522 A102012 10,000 14’ 23-7/8” 9” 4’ 9’ 24-1/2” 66” 60” 12 W 6248 A101614 6563 A101814 6878 A102014 10,000 16’ 23-7/8” 9” 4’ 10’ 24-1/2” 66” 60” 12 W 6400 A101616 6715 A101816 7030 A102016 10,000 18’ 23-7/8” 9” 4’ 10’ 29-1/2” 72” 66” 12 W 7031 A101618 7346 A101818 7661 A102018 10,000 20’ 24-1/2” 9” 4’ 10’ 29-1/2” 72” 66” 12 W 7788 A101620 8103 A101820 8418 A102020

FLOOR MOUNTED ‘A’ SERIES JIB CRANE SPECIFICATIONS

6/20/2016

SALES-A-6H12-13-05WJ

1377 Kimberly Dr., Neenah, WI 54956www.contrx.com

BOOM ASSEMBLYTROLLEY STOPS

(FACTORY MOUNTED)

4"

CONCRETE FOOTING

FLOOR

BASE DIAMETER

30°

BASE DETAIL

6 HOLES1-1/4" DIA.

BOLT CIRCLEDIAMETER

REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.

TROLLEY STOPS(FIELD MOUNTED)

1" ANCHOR BOLTS REQ'D.

ROLLERASSEMBLY

HEADASSEMBLY

COLUMNASSEMBLY

BC

FW

W

E

BC

BD

W

3/4 E

F A

D

CAPACITY

WEIGHT

A

B

C

D

E

F

NOTES

BC

W

BD

FW

LBS.

LBS.

• NOT DESIGNED FOR OUTDOOR USE

NOT TO SCALEDATE

DWG NO

FLOOR MOUNT 'A' JIBWITH 6-HOLE BASE

SALES-A-12H12-13-05WJ


BOOM ASSEMBLYTROLLEY STOPS

(FACTORY MOUNTED)

4"

CONCRETE FOOTING

FLOOR

BASE DIAMETER

BASE DETAIL

BOLT CIRCLEDIAMETER

REINFORCING RODS3/4" DIA. TOP AND BOTTOM ON

APPROX. 12" CENTERS BOTH WAYS.



ROLLERASSEMBLY

HEADASSEMBLY

COLUMNASSEMBLY

B

C

FW

W

E

BC

BD

W

3/4 E

F A

D

CAPACITY

WEIGHT

A

B

C

D

E

F

NOTES

BC

W

BD

FW

LBS.

LBS.

30°

12 HOLES1-1/4" DIA.


NOT TO SCALEDATE

DWG NO

FLOOR MOUNT 'A' JIBWITH 12-HOLE BASE

F A

B

C

D

FW

W

E

7/8" DIA.HOLE (4)

S

BW

SALES-A-FM12-13-05WJ


4' 0"

BOOM ASSEMBLY

CONCRETE FOOTING

FLOOR

REINFORCING RODS

3/4" DIA. TOP AND BOTTOM ON APPROX. 12" CENTERS BOTH WAYS.

TROLLEY STOPS(FACTORY MOUNTED)


ROLLERASSEMBLY

HEADASSEMBLY

COLUMNASSEMBLY

12"

BASEPLATE

SQUARE BASE PLATE DETAIL

CAPACITY

WEIGHT

A

B

C

D

E

F

S

W

BW

FW

LBS.

LBS.

NOTES • NOT DESIGNED FOR OUTDOOR USE

NOT TO SCALEDATE

DWG NO

FOUNDATION MOUNT 'A' JIB

F A

BC

D

FW

W

E

W

E

7/8" DIA.HOLE (4)

X

SBW

SALES-A-SM12-13-05WJ


4' 0"

BOOM ASSEMBLY

CONCRETE FOOTING

FLOOR


TROLLEY STOPS(FACTORY MOUNTED)


ROLLERASSEMBLY

HEADASSEMBLY

COLUMNASSEMBLY

12"

BASEPLATE

SLEEVE(INCLUDED)

4' 0"CONCRETE FOOTING

FLOOR

12"

SLEEVEBASE

PLATE

SLEEVE BASE PLATE DETAIL

SLEEVE

INSTALLATION INSTRUCTIONS

1. PREPARE FIRST POUR FOOTING WITH ANCHOR BOLTS SET AS SHOWN.

2. AFTER FOOTING HARDENS, INSTALL AND LEVEL SLEEVE.SECURE BASE TO PREVENT SHIFTING DURING SECOND POUR.

3. POSITION REBAR PATTERN APPROX. 6" FROM TOPAND BOTTOM OF SECOND POUR.

4. MAKE SECOND POUR FOUNDATION, TAKING CARE TO MAINTAINSLEEVE IN A PLUMB POSITION. ALLOW CONCRETE TO HARDEN.

5. INSERT JIB COLUMN INTO SLEEVE AND MAKE SURE CENTERING PINPASSES THROUGH HOLE IN CAP PLATE ON BOTTOM OF COLUMN.

6. PLUMB JIB COLUMN. BLOCKS OR WEDGES (NOT PROVIDED) MAY BEINSERTED BETWEEN SLEEVE AND COLUMN TO HELP MAINTAIN POSITION.

7. INSTALL JIB HEAD & BOOM SECTION ON COLUMN. ROTATE BOOM

8. WHEN POSITION OF COLUMN IS SATISFACTORY, INSTALL SPLITCOLLAR WITH FILLET WELDS TO BOTH COLUMN AND SLEEVE LIPALL THE WAY AROUND.

JIB COLUMN

SPLIT COLLAR

CENTERING PIN

WELD

FIRST POUR

SECONDPOUR

WEDGE

3/4" 'L' ANCHORS (4)

SLOWLY TO CHECK COLUMN PLUMBNESS. ADJUST BLOCKINGAS REQUIRED.

CAPACITY

WEIGHT

A

B

C

D

E

F

COLUMN OD

W

SBW

X

SLEEVE ID

FW

LBS.

LBS.


NOT TO SCALEDATE

DWG NO

SLEEVE MOUNT 'A' JIB

F A

BC

W

E

W

3/4E

D

FW

SALES-A-MD-12H12-13-05WJ


TIGHT WIRE ASSY BOOM ASSEMBLY

CONCRETE FOOTING

FLOOR

30°

BASE DETAIL

12 HOLES1-1/4" DIA.

BASE PLATEDIAMETERBD

BOLT CIRCLEDIAMETERBC




ROLLERASSEMBLY

HEADASSEMBLY

COLUMNASSEMBLY

SPROCKET

CONTROLPANEL

ACCESSHOLE

BRAKEMOTOR

GEARREDUCER

4C/SO CORD (POWER)6C/SO CORD (CONTROL)

4 RING BOTTOM ENTRYELECTRICAL COLLECTOR

4" DIA HOLE FORPOWER SUPPLY

4"

BASEPLATE

POWER IN

CAPACITY

WEIGHT

A

B

C

D

E

F

1/2 RPM115-1-60V

JIB ROTATION SPEED:CONTROL VOLTAGE:

NOTES BC

W

BD

SUPPLY VOLTAGE

FW

LBS.

LBS.


NOT TO SCALEDATE

DWG NO

MOTORIZED FLOOR MOUNT 'A' JIBWITH 12-HOLE BASE

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 722 5260 or (920) 725 1394 Fax

www.contrxcranes.com

INSTALLATION INSTRUCTIONS FLOOR MOUNT JIB CRANE

****PLEASE READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY****

1. The jib crane is shipped in three sections: head assembly, mast assembly, and boom assembly. A box containing the top bearing and mounting hardware is also included. For identical jibs ordered in multiple quantities, look for markings on the head assemblies and beam assemblies. Match each head assembly with the correct beam assembly.

2. The footing shown is the only method recommended by the manufacturer. An individual competent

in related foundation design methods and familiar with the installation site should design any alternative method.

3. Use a minimum 3000 PSI (5 bag) mix for concrete. A 2500 PSF soil pressure is assumed. Prior to

pouring, position the rebar and ‘L’ shaped anchor bolts as shown. Anchor bolts are submerged ¾ of footing depth. The anchor bolt material specification is A36. Rebar is located 6 inches from top and bottom of the footing. Be sure to allow for power conduit if feeding through the base of the jib. Position the anchor bolts according to the base plate bolt circle dimensions. (The anchor bolts can be purchased through your jib crane supplier.)

4. After the concrete hardens, make sure a flat, level surface exists for accepting the mast assembly.

Machinery grout and jam nuts may be used to level the surface. Erect the mast on the prepared surface, taking care not to damage the anchor bolt threads while setting the base plate in position. Tighten double nuts onto the anchor bolts after insuring that the mast is plumb.

5. Mount the top pivot bearing cone over the pin on top of the mast assembly. If installing the bottom

entry collector option, read the collector installation instructions at this time. Attach boom assembly to head assembly with the hardware provided. Set the boom and head assembly in place on the mast. Make sure the roller bearing on top of the mast is seated correctly into the bearing race on the boom assembly.

6. Adjust the lower roller assembly in the head section to bring the boom into horizontal.*

7. Grease upper bearing and 5” diameter lower rollers through zerk fitting provided. Re-lube as

conditions require. The 3” diameter lower rollers are self-lubricating. **

8. Rotate the boom assembly to check for free movement and proper bearing seating.

9. Install the trolley end stops on the boom. Attach other optional equipment according to directions provided with the equipment.

*Note - Small jibs are not adjustable at the lower rollers and may be leveled by shimming between the boom and the head mounting plates.

**Note - Small jibs are not equipped with a zerk fitting and need to be greased at the top bearing prior to seating the boom and head assembly.

WARNING: THIS EQUIPMENT IS NOT DESIGNED FOR AND SHOULD NOT BE USED FOR LIFTING, SUPPORTING OR TRANSPORTING PEOPLE.

12-11-07


Neenah, WI 54956-1642Phone (920) 722-0101Fax (920) 725-1394www.contrx.com Optional top entry electrical collector

can be attached to most 360° revolvingjib cranes. No special parts needed.

1-29-03

Boom Assembly

Upper PipeAssembly

ColumnAssembly

Base Plate

Concrete Foundation(by others)

"L" Anchor Bolts(Sold Separately)

Lower Thrust Roller (2)

Power In

Power to Crane Accessories

MEDIUM DUTY JIB CRANES- 360° ROTATION -

"B" SERIES

FLOOR MOUNTED

Contrx brand "B" series jib cranes are wellengineered and constructed machines ateconomical prices. The upper pipe assemblyis jig welded to assure accuracy. Two heavy dutylower thrust rollers with lubrication-free teflonbearings assure smooth operation as the boomrotates on a tapered roller bearing atop the columnassembly. The steel base plate and the columnpipe are welded together robotically to insure asquare connection.

Standard Features:• Boom rotates 360°• Rolled steel I-beam boom fits most standard hoist trolleys.• Bolt-on trolley end-stops allow easy trolley installation.• Safety yellow enamel primer and paint finish• Mounting details provided with installation instructions• Adjustable rollers on 2000 lb. capacity units allow for boom leveling.

Options:• Anchor bolt kits• Base plate templates (paper or plywood)• Hoists and trolleys• Boom rotation stops• Top entry electrical collectors• Tagline festoon kits• Contact us for special requests.

TrolleyEnd Stops

End StopMountingHardware

Boom Assembly


Main Bearing Cup(Pressed in at Factory)

Upper PipeAssembly

Main Bearing Cone

Upper Bearing Pin

Jib Column

AnchorBolt Hardware

Column Gussets

Jib Base Plate

Concrete Footing and'L' Anchor Bolts(By Customer) Refer to:FLOOR MOUNT 'B' JIBdrawing number

___________________

Thrust Washer (2)

LowerRoller (2)

Lock Pin (2)

Roller Shaft


Office (920) 722-0101Fax (920) 725-1394

www.contrx.com

RollerShaft (2)

ThrustWasher (2)

LowerRoller (2)

LevelingScrew (4)


Adjustable Lower Roller AssemblyUsed on the following jibs:

-All 1000# cap. with 16'-0" boom--All 2000# cap. B-jibs-

Boom Length

DWG NO

'B' Jib Assembly Detail

B-1005-B10-4-06 Not to scale

Assembly Note: Center the lower rollers directly below the boom.

1-1-11

FLOOR MOUNTED 'B' SERIES JIB CRANE SPECIFICATIONS

Jib CraneAccessories:

- Anchor Bolt Kits- Tagline Kits- Templates (paper & plywood)- Hoists & Trolleys (electric & manual)


Phone (920) 722-0101Fax (920) 725-1394www.contrx.com

24R6

26R6 28R8 30R12

15S4

500

750

1000

2000

250

500

750

1000

2000

250

500

750

1000

2000

250

500

750

1000

250

500

750

1000

250500

750

1000

2000

250

8'

8'

8'

8'

8'

10'

10'

10'

10'

10'

12'

12'

12'

12'

12'

14'

14'

14'

14'

16'

16'

16'

16'6'

6'

6'

6'

6'

5"

6"

6"

8"

5"

5"

6"

8"

8"

5"

6"

6"

8"

10-3/8"

5"

8"

8"

8"

6"

8"

8"

10-3/8"

6"5"

5"

6"

8"

5"

3"

3 3/8"

3 3/8"

4"

3"

3"

3 3/8"

4"

4"

3"

3 3/8"

3 3/8"

4"

5-3/4"

3"

4"

4"

4"

3 3/8"

4"

4"

5-3/4"

3 3/8"3"

3"

3 3/8"

4"

3"

4'

4'

4'

5'

4'

4'

4'

4'

5'

4'

4'

4'

4'

6'

4'

5'

5'

5'

5'

5'

5'

5'

5'4'

4'

4'

5'

4'

3'

3'

3'

4'

3'

3'

3'

3'

4'

3'

3'

3'

3'

4'

3'

3'

3'

3'

3'

3'

3'

3'

3'3'

3'

3'

4'

3'

5"

6 1/2"

6 1/2"

8 1/2"

4"

5"

6 1/2"

7 1/2"

8 1/2"

4"

6 1/2"

7 1/2"

7 1/2"

9 1/2"

4"

6 1/2"

7 1/2"

7 1/2"

4"

6 1/2"

7 1/2"

8 1/2"

5"5"

6 1/2"

6 1/2"

8 1/2"

4"

15S4

24R6

26R6

28R8

15S4

15S4

24R6

26R6

28R8

15S4

24R6

24R6

26R6

30R12

15S4

24R6

24R6

26R6

15S4

24R6

26R6

26R6

15S415S4

24R6

26R6

28R8**

15S4

378

504

515

802

329

398

529

756

739

349

554

707

793

1091

369

665

818

848

425

702

866

1070

499358

463

490

745

309

B5108

B75108

B1108

B2108

B25108

B51010

B751010

B11010

B21010

B251010

B51012

B751012

B11012

B21012

B251012

B51014

B751014

B11014

B251014

B51016

B751016

B11016

B251016B5106

B75106

B1106

B2106

B25106

B5128

B75128

B1128

B2128

B25128

B51210

B751210

B11210

B21210

B251210

B51212

B751212

B11212

B21212

B251212

B51214

B751214

B11214

B251214

B51216

B751216

B11216

B251216B5126

B75126

B1126

B2126

B25126

B588

B7588

B188

B288

B2588

B5810

B75810

B1810

B2810

B25810

B5812

B75812

B1812

B2812

B25812

B5814

B75814

B1814

B25814

B5816

B75816

B1816

B25816B586

B7586

B186

B286 **

B2586

416

549

560

869

358

436

574

812

905

378

599

763

849

1165

398

710

874

904

454

747

922

1137

537396

508

535

832

338

454

594

605

935

388

474

619

868

972

408

644

819

905

1238

428

755

931

960

484

792

978

1204

575434

553

580

899

368

CAP.(LBS.)

DIMENSIONSA D FW E W F

BASE PLATEMODEL LBS. MODEL LBS. MODEL LBS. MODEL

B = 10' HT. B = 12' HT.B = 8' HT.

BASE PLATEMODEL

BASEDIA.

BOLTCIRCLE

NO.HOLES

HOLEDIA.

BOLTDIA.

24R626R628R8

30R12

15S424"26"28"30"

20"22"24"26"

668

12

41 1/4"1 1/4"1 1/4"1 1/4"

7/8"1"1"1"1"

3/4"

AF

B

FW

W

E

D

3/4 E

4"

12"15"

15"

12"

"S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam. ** B286 Uses base plate model 26R6.

UPPERPIPE

COLUMNASSEMBLY

BASEPLATE

LOWERROLLERS

REINFORCING RODS5/8" DIA. TOP - 3/4" DIA. BOTTOMAPPROX. 12" ON CENTERBOTH WAYS

BOOMASSEMBLY

S

S

S

S

S

S

S

S

S

S

S

S

S

W

S

S

S

S

S

S

S

W

SS

S

S

S

S

BEAMTYPE

AF

FW

D

B

W

E3/4 E

C

SALES-B12-13-05WJ


24R6 26R6 28R8 30R1215S4

BASE PLATEMODEL

BASEDIA.

BOLTCIRCLE

NO.HOLES

HOLEDIA.

BOLTDIA.

24R626R628R830R12

15S424"26"28"30"

20"22"24"26"

668

12

41 1/4"1 1/4"1 1/4"1 1/4"

7/8"1"1"1"1"

3/4"

12"15"

15"

12"

UPPERPIPE

COLUMNASSY.

BASEPLATE

LOWERROLLERS

REINFORCING RODS5/8" DIA. TOP - 3/4" DIA. BOTTOMAPPROX. 12" ON CENTERBOTH WAYS

BOOMASSEMBLY

CONCRETEFOOTING

4"

B

C

D

E

F

W

FW

CAPACITY

WEIGHT

A

BOLTCIRCLEDIAMETER

BASEDIAMETERNOTES


NOT TO SCALEDATE

DWG NO

FLOOR MOUNT 'B' JIB


Neenah, WI 54956-1642Phone (920) 722-0101


3-7-14

PORTABLE JIB CRANE

This innovative design eliminates the need for costly sitepreparation. The portable jib crane comes with its ownsteel base. No traditional concrete footing is required.

Eliminate conventional jib location restrictions while gainingtrue portability and versatility.

360° Boom Rotation

• No concrete foundation or floor anchoring required

• Easily moved by fork truck for multiple uses

• Easy to store and transport

• Use not limited to ground floor applications

• Not limited to industrial use

2"

FLOOR

A

B

F

D

FW

E

W

S

A

6'-0"

D

5"

E

4"

F

4"

S

26"

FW

3.00"

(LBS.)

2221

CAPACITY(LBS) WEIGHT

W

48"8'-0" 5" 4" 4" 26" 3.00" 224148"10'-0" 5" 6" 4" 26" 3.00" 342748"12'-0" 5" 7" 4" 26" 3.00" 4098

25048"

14-0" 6" 8" 4" 26" 3.33" 480748"

6'-0" 5" 6" 5" 3.00" 34358'-0" 5" 7" 5" 3.00" 410610'-0" 5" 9" 5" 3.00" 5430

500

12'-0" 6" 6" 6 1/2" 3.33" 5571

6'-0" 6" 4" 6 1/2" 3.33" 38098'-0" 6" 6" 6 1/2" 3.33" 5521

1000

PORTABLE JIB CRANE SPECIFICATIONS

MODEL

PBB2586PBB2588

PBB25810PBB25812PBB25814

PBB586PBB588

PBB5810PBB5812

PBB186PBB188

B = 8'-0"

(LBS.)

2250

WEIGHT

2270345641284836

3473414454685615

38545565

MODEL

PBB25106PBB25108

PBB251010PBB251012PBB251014

PBB5106PBB5108

PBB51010PBB51012

PBB1106PBB1108

B = 10'-0"

(LBS.)

2279

WEIGHT

2299348541574865

3511418255065660

38955610

MODEL

PBB25126PBB25128

PBB251210PBB251212PBB251214

PBB5126PBB5128

PBB51210PBB51212

PBB1126PBB1128

B = 12'-0"DIMENSIONS

Features:• Can be easily moved from place to place• Requires no concrete foundation• Can be used on floors above ground floor• Can be easily stored out of the way

Portable Jib Crane Accessories:• Tagline Kits• Trolleys• Hoists• Rotation Stops• Optional Base sizes

Fork Pockets (extend through the base) FP1 = 3" X 7"FP2 = 3-1/2" X 7-1/2"FP3 = 3-1/2" X 8"

26" 48"26" 48"26" 48"26" 60"

26" 60"26" 60"

Not to be used as aforklift truck attachment

• Lifting Lugs

Base footprint is square

BASE

(WEIGHT IS FOR JIB CRANE ONLY)

5-21-13


Office (920) 722-0101Fax (920) 725-1394

www.contrx.com

FP2

POCKETSFORK

FP2FP3FP3FP3

FP3FP3FP3FP3

FP1FP3

TrolleyEnd Stops


Boom Assembly



Upper PipeAssembly

Main Bearing Cone

Upper Bearing Pin

Jib Column

Anchor BoltBolt Hardware Column Gussets

Jib Base Plate

Thrust Washer (2)

LowerRoller (2)

Lock Pin (2)

Roller Shaft


Office (920) 722-0101Fax (920) 725-1394

www.contrx.com

DWG NO

Portable Jib Assembly Detail

PBB-1005-A8-29-02 Not to scale



Neenah, WI 54956-1642Phone (920) 722-0101


3-29-16

WORKSTATION JIB CRANE

Use this ergonomically designed jib for repetitivemotion material handling applications. Low friction

track and trolley reduces operator fatigue in pick andplace operations. Special trolley, included with the jib

crane, will accept most small capacity hoist hooks.

360° Boom Rotation

FEATURES:

• Available in 100 lb., 250 lb., and 500 lb. capacity

• Boom reach up to 10 ft.

• High-strength enclosed track protects running surface from dirt for minimal resistance.

• Lifetime lubricated and sealed wheel bearings in trolley

• Easy to control load placement

• Fast installation: 100 lb. and 250 lb. capacity units can be anchored to most existing concrete floors.

• Easy to relocate

OPTIONS:

• Anchor bolt kits

• Festooning trolley kit

• Rotation stops

• Top entry electrical collector

• Mounting template

• Adjustable rubber trolley stops

• Light weight electric chain hoist

Load Trolley Included

TrolleyEnd Stop


Boom AssemblyBoom Mounting

Hardware


Upper PipeAssembly

Main Bearing Cone

Upper Bearing Pin

Jib Column

AnchorBolt Hardware

Column Gussets

Jib Base Plate(100 lb. models have square base plates)

'L' anchor bolts shown are recommendedfor 500 lb. capacity models.Expansion anchors may be used on100 lb. and 250 lb. capacity models.(Anchors not included)

Thrust Washer (2)

LowerRoller (2)

Lock Pin (2)

Roller Shaft (2)


Office (920) 722-0101Fax (920) 725-1394

www.contrx.com

Concrete Footing

Trolley (Included)

Shim here to adjust boom level.

DWG NO

Workstation Jib Assembly Detail

WSB-10054-6-16 Not to scale


7-10-06

W

E 3/4 E

D

A

10' 0"



WSB WORKSTATION JIB CRANE SPECIFICATIONS

Jib Crane Accessories:

• Anchor bolt kits• Festooning trolley kit• Templates (paper & plywood)• Top entry electrical collector• Adjustable rubber stops• Rotation stops• Hoists (electric & manual)

BASEPLATE

BOOM ASSEMBLY

UPPERPIPE

COLUMNASSEMBLY

SQUARECONCRETEFOOTING

4"

ANCHORS (BY OTHERS)

FLOOR

35"

35H6 32"23H6 20"

23"15"

12"15S4

Base Plates

Cap.(lbs.)100100100250250250500500500

"A"(ft.)681068106810

"D"(in.)6-3/47-3/48-3/48-3/48-3/49-3/49-3/49-3/411-3/4

"G"(in.)

"E"(in.)

"W"(in.)486060486060486060

666666121212

222222222

BasePlt.

15S415S415S423H623H623H635H635H635H6

Wt.(lbs.)379424479424549604614754834

AnchorDia. (in.)

3/43/43/4111111

MODEL NO.WSB1106WSB1108WSB11010WSB25106WSB25108WSB251010WSB5106WSB5108WSB51010

EXPANSION TYPE ON 100 & 250 LB. JIBS'L' TYPE (SHOWN) ON 500 LB. JIBS

G

TROLLEY(INCLUDED)


Neenah, WI 54956-1642Phone (920) 722-0101


3-20-14

CONTRX INDUSTRIES, IN

C.

NEENAH, WI 5

4956

920-722-0101

MODEL NO.

SERIAL NO.

FULL-CANTILEVEREDWALL MOUNT JIB CRANE

• 180° rotation

• Ideal for maximum headroom and trolley travel

• Mount at any height on wall or building columns where strength permits and true vertical alignment is possible

• High grade steel components for long life

• Hinges with self-lubricating teflon bearings and hardened pins

• Capacities to 6,000 lbs. - standard lengths to 20'

• Primed and painted safety yellow

Options:• Hoists and trolleys• Boom rotation bumpers• Tagline festoon kits• Contact us for special requests.

WMCC608WMCC610WMCC612

WMCC414

WMCC614

WMCC420

WMCC620

WMCC220

WMCC618

WMCC218

4000 LB.

4000 LB.

6000 LB.6000 LB.

6000 LB.6000 LB.6000 LB.

6000 LB.

2000 LB.2000 LB.

8'10'12'

14'

14'

18'

18'

20'

20'

20'

4'4'6'

5'

6'

7'-6"

6'

7'-6"

9'-6"

6'

16"16"16"

16"

16"

23 3/4" 7" WF

23 3/4"

16"

23 3/4"

16"

7" WF7" WF7" WF

7" WF

7" WF

7" WF

7" WF

7" WF

7" WF

8"

8"8"8"8"

8"8"

8"

8"

8"

18"18"22"

16"

22"

22"

18"

22"

2"2"

2"

2"

3"

2"

3"

3"

2"

2" 146751844814871

14240

17440

18629

16" 8561

14521

16512

16" 9643

679759974

887

1054

1743

1083

1840

2135

1163

11/16"

11/16"

11/16"11/16"

11/16"

11/16"

11/16"11/16"

11/16"

13/16"*

*

*

1-1-11

11/16"

WMCC416

WMCC616

WMCC418 4000 LB.4000 LB.

6000 LB.

16'

16'

18'6'

6'-6"

6'21"

21"

21"6-1/2" WF

6-1/2" WF

6-1/2" WF

8"

8"8" 16"

22"

18"3"

3"

3"14052

18844

159981256

1402

146511/16"11/16"

WMCC408WMCC410WMCC412

WMCC120

WMCC216

4000 LB.4000 LB.4000 LB.

2000 LB.

1000 LB.

8'10'12'

16'

20'

4'4'4'

6'

6'

12-3/8"12-3/8"12-3/8"

12-3/8"

12-3/8"

6-1/2" WF6-1/2" WF6-1/2" WF

6-1/2" WF

6-1/2" WF

8"8"8"

8"

7"

16-3/8"16-3/8"16-3/8"

16-3/8"

2"2"

2"

2"

2" 98231235914924

16-3/8" 7272

5394

469529589

765

8759/16"

11/16"11/16"11/16"

11/16"

WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANEMUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM.

* THESE CRANES SHIP IN TWO PIECES AND HAVE BOLT ON BOOMS.

WMCC FULL CANTILEVERED JIB CRANE SPECIFICATIONS

1377 Kimberly DriveNeenah, WI 54956-1642Phone (920) 722-0101Fax (920) 725-1394www.contrx.com

MODEL NO. CAPACITY THRUST& PULL (LBS.)A B D FW E F G

WMCC208

WMCC108

WMCC508

WMCC210

WMCC110

WMCC510

WMCC212

WMCC112

WMCC512

WMCC214

WMCC114

WMCC514

WMCC520

WMCC116

WMCC516

WMCC118

WMCC518

2000 LB.2000 LB.2000 LB.

2000 LB.

1000 LB.1000 LB.

1000 LB.1000 LB.1000 LB.

1000 LB.

500 LB.500 LB.500 LB.

500 LB.500 LB.500 LB.

500 LB.

8'

8'

8'

10'

10'

10'

12'

12'

12'

14'

14'

14'

16'

16'

18'

18'20'

4'

3'

3'

5'

3'

3'

5'

3'

4'

5'

4'

4'

4'

4'

4'

4'4'

8"

8"

6"

10-3/8"

8"

6"

10-3/8"

8"

6"

10-3/8"

8"

6"

10-3/8"

8"

10-3/8"

8"10-3/8"

4"

4"

3 3/8"

5-3/4" WF

4"

3 3/8"

5-3/4" WF

4"

3 3/8"

5-3/4" WF

4"

3 3/8"

5-3/4" WF

4"

5-3/4" WF

4"5-3/4" WF

7"

8"

7"7"7"7"7"7"7"

7"7"7"

8"8"

7"7"

7"

12"

10"

12"

10"

12"

12"

16-3/8"

12"

16-3/8"

12"

16-3/8"

12"16-3/8"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2"2"

2"

2"

2"

16-3/8" 5110

3680

2080

WEIGHT(LBS.)

16-3/8" 5226

4662

2641

16-3/8" 6329

5668

2425

16-3/8" 7453

5046

2871

6069

3526

6940

40494967

371

277

205

527

314

230

579

350

304

631

482

329

644

442

696

479747

E

3"

2"

2"

6"

6 BOLTHOLES

FW

B

A4 1/2"

D

END STOP

CONSULT FACTORY FOR:

- Special boom lengths and capacities- Motorized rotation- Mounting hardware- Hinge kits- Matching hoist and trolley systems

BOLT HOLE DIA.

9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"

9/16"

11/16"11/16"11/16"

FWALLBRACKET

VERTICAL BEAM

BOOM

G

2"2"

WALL BRACKETBOLT PATTERN

SALES-WMCC12-13-05WJ


D

A

4-1/2"

B

F

E

FW

WALL BRACKET

6"3"

2"

2"WALL BRACKET

MOUNTINGBOLT PATTERN

2"

2"HINGE PIN

INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.

DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE TO SUPPORT THE CRANE.

USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILL THE BOLTHOLES IN THE SUPPORTING STRUCTURE. BE SURE THAT BOTH HINGE PINSSHARE A COMMON TRUE VERTICAL CENTERLINE.

RAISE THE CRANE INTO POSITION AND BOLT THE HINGES TO THE

USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS)USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES.

INSTALL HOIST AND TROLLEY BY REMOVING END STOPS.SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS.

1.

2.

3.

4.

SUPPORTING STRUCTURE.

END STOP

CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.5.

(6) HOLES

B

D

E

F

MOUNTING HOLE DIA.

FW

CAPACITY

WEIGHT

A


NOT TO SCALEDATE

DWG NO

FULL CANTILEVER WALL MOUNT JIB


Neenah, WI 54956-1642Phone (920) 722-0101


5-2-08

CONTRX INDUSTRIES, INC.

NEENAH, WI 5

4956

920-722-0101

MODEL NO.

SERIAL NO.

OVERBRACED TIE-ROD JIB CRANEWALL MOUNTED

• 180° rotation

• Economical hook coverage with rotation

• Single tie-rod with threaded ends for easy field adjustment

• Mount at any height on wall or building columns where strength permits and true vertical alignment is possible


• Hinges with self-lubricating teflon bearings and hardened pins

• Capacity to 6,000 lbs. - standard lengths to 20' 0"


Options:• Hoists and trolleys• Boom rotation bumpers• Tagline festoon kits• Contact us for special requests.

1-1-11



WMC OVERBRACED TIE ROD JIB CRANE SPECIFICATIONS

WMC608WMC610WMC612

WMC414

WMC614

WMC420

WMC620

WMC220

WMC618

WMC218

4000 LB.

4000 LB.

6000 LB.6000 LB.

6000 LB.6000 LB.6000 LB.

6000 LB.

2000 LB.2000 LB.

8'10'12'

14'

14'

18'

18'

20'

20'

20'

2'-9"3'-3"4'-0"

4'-6"

4'-9"

6'-3"

6'-0"

6'-6"

7'-0"

6'-0"

8"8"

10-1/2"

8"

10-1/2"

12-3/8" 6-1/2" WF

16"

8"

16"

10-3/8"

4"4"

5-3/4" WF

4"

5-3/4" WF

7" WF

4"

7" WF

5-3/4" WF

8"

8"8"8"8"

8"8"

8"

8"

8" 2'-0"

2'-0"

2'-6"

2'-6"220702319322668

15724

22251

22160

2'-6" 8082

15973

22056

2'-6" 9266

317364560

431

631

963

467

811

1397

671

13/16"13/16"13/16"13/16"11/16"

11/16"

11/16"11/16"

13/16"13/16"

MODEL NO. CAPACITY THRUST& PULL (LBS.)A B D FW E F

WMC408

WMC208

WMC108

WMC508

WMC410

WMC210

WMC110

WMC510

WMC412

WMC212

WMC112

WMC512

WMC214

WMC114

WMC514

WMC120

WMC520

WMC416

WMC616

WMC216

WMC116

WMC516

WMC418

WMC118

WMC518

4000 LB.4000 LB.

4000 LB.4000 LB.4000 LB.

6000 LB.

2000 LB.

2000 LB.2000 LB.2000 LB.

2000 LB.

1000 LB.1000 LB.1000 LB.

1000 LB.1000 LB.1000 LB.

1000 LB.

500 LB.500 LB.500 LB.

500 LB.500 LB.500 LB.

500 LB.

8'

8'

8'

8'

10'

10'

10'

10'

12'

12'

12'

12'

14'

14'

14'

16'

16'

16'

16'

16'

18'

18'

18'

20'

20'

2'-9"

2'-9"

2'-9"

2'-9"

3'-0"

3'-0"

3'-0"

3'-0"

3'-9"

3'-9"

3'-9"

3'-9"

4'-6"

4'-6"

4'-6"

5'-6"

5'-6"

5'-6"

5'-6"

5'-6"

6'-0"

6'-0"

6'-0"

6'-6"

6'-6"

8"

6"

6"

6"

8"

6"

6"

6"

8"

6"

6"

6"

8"

6"

6"

10-3/8"

10-1/2"

8"

6"

6"

10-3/8"

8"

8"

8"

8"

4"

3 3/8"

3 3/8"

3 3/8"

4"

3 3/8"

3 3/8"

3 3/8"

4"

3 3/8"

3 3/8"

3 3/8"

4"

3 3/8"

3 3/8"

5-3/4" WF

5-3/4" WF

4"

3 3/8"

3 3/8"

5-3/4" WF

4"

4"

4"

4"

8"

8"8"

8"8"8"

8"

7"

8"

7"7"7"7"7"7"7"

7"7"7"

8"8"

7"7"7"

7"

1'-3"

1'-3"

1'-3"

1'-3"

1'-6"

1'-6"

1'-6"

1'-6"

1'-9"

1'-9"

2'-0"

2'-0"

2'-0"

2'-0"

2'-3"

2'-3"

2'-0"

2'-0"

2'-3"

2'-3"

2'-0"

2'-0"

2'-3"

2'-3"

14822

1'-3" 7681

4118

2367

WEIGHT(LBS.)

16895

1'-6" 8766

4720

2731

16182

2'-0" 8406

4545

2648

2'-0" 8312

4440

2603

14880

21966

2'-3" 7802

4175

2463

15384

4499

2738

4662

2860

297

202

202

202

341

242

232

232

386

272

261

261

384

292

292

607

702

426

323

323

668

458

458

500

500

E

3"

2"

2"

6"

6 BOLTHOLES

CONSULT FACTORY FOR:

• Special boom lengths and capacities• Motorized rotation

BOLT HOLE DIA.

9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"9/16"

9/16"

13/16"

11/16"11/16"

11/16"11/16"11/16"

11/16"11/16"11/16"11/16"

2"2"

WALL BRACKETBOLT PATTERN

FWEND STOP

• Mounting hardware• Hinge kits• Matching hoist and trolley systems

B

4 1/2" A2"

D

F

WALL BRACKETTIE ROD HINGE

TIE ROD

TIE ROD YOKE

HINGE PIN

BOOM BOOM BRACKET

WF INDICATES THAT THIS JIB CRANE USES A WIDE-FLANGE BEAM. THE TROLLEY USED ON THIS CRANEMUST BE DESIGNED TO OPERATE ON A WIDE-FLANGE BEAM.

SALES-WMC12-13-05WJ


A4-1/2"

B

FWD

F

E

WALL BRACKETTIE ROD HINGETIE ROD YOKE

TIE ROD

HINGE PIN

BOOM

BOOM BRACKET

END STOP 2"

INSTALLATION NOTESNOTE: PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION.

DETERMINE THE SUPPORTING STRUCTURE IS ADEQUATE

USE THE WALL BRACKET PATTERN SHOWN TO MARK AND DRILLTHE BOLT HOLES IN THE SUPPORTING STRUCTURE. BE SURE THATBOTH HINGE PINS SHARE A COMMON TRUE VERTICAL CENTERLINE.

BOLT THE UPPER HINGE TO THE MOUNTING SURFACE.USE MINIMUM GRADE 5 BOLTS AND NUTS (SUPPLIED BY OTHERS)USE BOLTS 1/16" LESS IN DIAMETER THAN THE BOLT HOLES.

INSTALL HOIST AND TROLLEY BY REMOVING END STOPS.SLIDE THE TROLLEY ONTO THE BOOM AND REPLACE THE END STOPS.

1.

2.

3.

6.

CONTACT CONTRX INDUSTRIES (920) 722-0101 FOR ADDITIONAL ASSISTANCE.7.

WHILE SUPPORTING THE BOOM HORIZONTALLY, BOLT THE LOWERHINGE AND BEAM TO THE MOUNTING SURFACE.

4.

ATTACH THE ROD BETWEEN THE UPPER HINGE AND BOOM BRACKET WITH THENUTS AND WASHERS PROVIDED. ADJUST THE NUTS TO LEVEL THE BOOM.

5.

6"3"

2"

2"WALL BRACKET

MOUNTINGBOLT PATTERN

2"

2"

TO SUPPORT THE CRANE.

(6) HOLES

B

D

E

F

MOUNTING HOLE DIA.

FW

CAPACITY

WEIGHT

A


NOT TO SCALEDATE

DWG NO

OVERBRACED TIE ROD WALL MOUNT JIB


Neenah, WI 54956-1642Phone (920) 722-0101


7-31-08

CONTRX INDUSTRIES, IN

C.

NEENAH, WI 5

4956

920-722-0101

MODEL NO.

SERIAL NO.

PILLAR MOUNTJIB CRANE

• 360° rotation

• Ideal for maximum headroom and trolley travel


• Mounting plates with spherical roller bearings

• Capacities to 4,000 lbs. - standard lengths to 20'


Options:• Hoists and trolleys• Tagline festoon kits• Contact us for more information


Neenah, WI 54956-1642Phone (920) 722-0101


10-8-03

PORTABLE GANTRY CRANES

• Automotive• Trucking• Manufacturing• Loading Docks• Aircraft• Implement• Marine• Warehouses• Maintenance

• Capacities From 1 to 5 Ton• Spans from 8 to 16 Feet• Heights from 8 to 16 Feet• Portable• Custom Sizes Available• 2 Large Steel Swivel Casters• 2 Large Steel Swivel Casters with Brakes• Standard "I" Beams• Painted Safety Yellow• Built to meet ANSI and OSHA Requirements

APPLICATIONS OF FIXED HEIGHT &TELESCOPING GANTRIES

FEATURES OFFIXED HEIGHT &TELESCOPING GANTRIES

TelescopingGantry Crane

Fixed HeightGantry Crane

2-2-11


Phone (920) 722-0101Fax (920) 725-1394

PORTABLE GANTRY CRANE SPECIFICATIONS

www.contrx.com

FIXED & TELESCOPING GANTRY CRANESSemi-steel heavy-duty swivel casters with rollerbearings are standard equipment. Two casters are supplied with brakes.

Gantries are easily disassembled and assembled for relocation.

Contact factory for special heights, spans, and options.

Our Fixed Height Gantry Cranes are ideal for use in aircraft, automotive, and marine repair shops. They also work wellin warehouses, machine shops, and loading areas. Gantry cranes are supplied with four roller-bearing steel wheelsfor easy maneuverability. The structural steel legs are welded together at the factory. Gantry crane requires assemblybefore use.

Our Telescopic Height Gantry Cranes have the same abilities as our fixed height gantries with the added benefit ofraising or lowering the beam to suit your need. The beam will adjust from 8'-0" to 12'-0" below the beam withpositive stops every 6". The beam is raised and lowered with the aid of two cable pullers (included). Locking pinshold the beam at the desired height.

GCT1-12

GC1-12

GCT1-16

GC1-16

GCT2-8

GC2-8

GCT2-12

GC2-12

GCT2-16

GC2-16

GCT3-8

GC3-8

GCT3-12

GC3-12

GCT3-16

GC3-16

GCT4-8

GC4-8

GCT4-12

GC4-12

GCT4-16

GC4-16

GCT5-8

GC5-8

GCT5-12

GC5-12

GCT5-16

GC5-16

GCT1-8

GC1-8

1

1

1

1

2

2

2

2

2

2

3

3

3

3

3

3

4

4

4

4

4

4

5

5

5

5

5

5

1

1

5" X 1 5/8"

5" X 1 5/8"

5" X 1 5/8"

5" X 1 5/8"

8" X 1 1/2"

8" X 1 1/2"

8" X 1 1/2"

8" X 1 1/2"

8" X 1 1/2"

8" X 1 1/2"

8" X 2 1/2"

8" X 2 1/2"

8" X 2 1/2"

8" X 2 1/2"

8" X 2 1/2"

8" X 2 1/2"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

8" X 3"

5" X 1 5/8"

5" X 1 5/8"

13'-5 9/16"

13'-5"

17'-5 9/16"

17'-5"

9'-6 5/8"

9'-6"

13'-6 5/8"

13'-6"

17'-6 5/8"

17'-6'

9'-6 5/8"

9'-6 5/8"

13'-6 5/8"

13'-6 5/8"

17'-6 5/8"

17'-6 5/8"

9'-8 5/8"

9'-8 5/8"

9'-8 5/8"

9'-8 5/8"

13'-8 5/8"

13'-8 5/8"

13'-8 5/8"

13'-8 5/8"

17'-8 5/8"

17'-8 5/8"

17'-8 5/8"

17'-8 5/8"

9'-5 9/16"

9'-5"

12'

12'

12'

12'

12'

12'

12'

12'

12'

12'

16'

16'

16'

16'

16'

16'

16'

16'

16'

16'

8'

8'

8'

8'

8'

8'

8'

8'

8'

8'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

5'

8'

8'

8'

8'

8'

10'

8'

8'

8'

8'

8'

10'

12'

12'

12'

12'

12'

10'

12'

12'

12'

12'

12'

10'

12'

12'

12'

12'

12'

10'10'10'10'10'10'10'10'10'10'

8'

8'

8'

8'

8'

10'

3 3/8"

3 3/8"

4"

4"

3 3/8"

3 3/8"

4"

4"

5-3/4"

5-3/4"

8"

8"

7-1/8"

7-1/8"

4"

4"

8"

8"

7-1/8"

7-1/8"

5-3/4"

5-3/4"

8"

8"

7-1/8"

7-1/8"

8"

8"

3"

3"

807

600

957

750

886

651

1016

781

1266

1030

1202

1018

1431

1247

1778

1594

1607

1393

1763

1549

1989

1776

1865

1651

2093

1879

2321

2107

733

5266"8"6"8"

10-3/8"

9-7/8"

16-3/8"

8"

9-7/8"

16-3/8"

10-1/2"

13-5/8"

16-3/8"

13-5/8"

5"

MODELNUMBER

MODELNUMBER

CAP.(TONS)

CAP.(TONS)

STEELWHEELS

STEELWHEELS

C

C

D

D

E

E

F

F G

FW

FW

WEIGHT(LBS.)

WEIGHT(LBS.)

MIN. MAX.

FIXED HEIGHT GANTRY CRANE SPECIFICATIONS

TELESCOPING HEIGHT GANTRY CRANE SPECIFICATIONS

C FW

FLOOR

FLOOR

D

FWC

D

E

E

F

F

G

G

CABLEPULLER(2)

* DIAMETER OF WHEELS BY TREAD WIDTH** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.

* DIAMETER OF WHEELS BY TREAD WIDTH** "S" type beams are standard beams with tapered flanges. "W" type beams are wide-flange beams with flat flanges. The trolley used on a "W" type beam must be designed to operate on a wide-flange beam.

*

* BEAMTYPE**

SSSSWSWWWWWWWW

S

BEAMTYPE**

SSSSWSWWWWWWWW

S6"8"6"8"

10-3/8"

9-7/8"

16-3/8"

8"

9-7/8"

16-3/8"

10-1/2"

13-5/8"

16-3/8"

13-5/8"

5"

G

OPTIONS: • (2) STEEL SWIVEL CASTERS • (2) STEEL SWIVEL CASTERS WITH BRAKES SALES-GC

12-13-05WJ


C

D

G

FW

F

E

W

D

E

F

G

W

FW

CAPACITY

WEIGHT

C


NOT TO SCALEDATE

DWG NO

FIXED HEIGHT GANTRY CRANE

OPTIONS: • (2) STEEL SWIVEL CASTERS • (2) STEEL SWIVEL CASTERS WITH BRAKES • HEIGHT IS ADJUSTABLE IN 6" INCREMENTS

SALES-GCT12-13-05WJ


C

D

G

FW

MAXMIN

E

W

CABLE PULLER(2) INCLUDED

D

E

G

FW

MAX

MIN

W

CAPACITY

WEIGHT

C


NOT TO SCALEDATE

DWG NO

TELESCOPING GANTRY CRANE


Neenah, WI 54956-1642Phone (920) 722-0101


1

2

10-29-10

3

4

5

6

7

Alternate Hook PositionsTelescoping BoomBoom HandleSafety Swivel Hooks (2)Fork Pockets48" Safety Chain with Grab HookSpring Loaded Boom Lock

• Converts lift truck into a crane inexpensively• Moves cumbersome items your forks can't reach.• Crane reaches out and picks up from overhead.• Reaches through or over obstructions.

Minimize manhandling of shipments andequipment without investing a lot of money

in new power equipment. Jib lift lets youconvert your standard lift truck into a mobilecrane at minimal cost. You can enjoy the

convenience of this versatile equipment without duplicating power equipment...and it's easy touse. One man can install in minutes withoutremoving forks, just by slipping onto forks. 48" safety chain anchors it to truck's frame.Constructed of heavy structural steel tubing;

two safety swivel hooks provided.

1

6

3

4

2

7

5

TELESCOPING JIB LIFT

Check with manufacturerof your lift truck for load

capabilities before using.



145" MAX

SW

TL

H.U.B.

HOOKPOSITION

9

CENTER OFGRAVITY

BOOM CONTRACTED

BOOM EXTENDED

CENTER OFGRAVITY

SAFETY PIN LOCKSBOOM IN POSITION


IMPORTANT

CENTER OF GRAVITY LOCATION

TRUCK FORKS MUSTEXTEND THROUGH FULLLENGTH OF FORK TUBES

FEATURES• Handles long loads in closed trucks• High and long reaches for inaccessible areas• High underclearances and bulky load handling

A B C D EHOOK POSITION

85" MIN

TL

H.U.B.


HOOKPOSITION

1

OAHY

Y

X

XX

SINGLE HOOK CAPACITIES

HookPos.

123456789

HookPosition(inches)

8087-1/2

95102-1/2

110117-1/2

125132-1/2

140

4000LB.

CAP.

400035353167286826212413223520821949

6000LB.

CAP.

600053024750430239313619335331232923

8000LB.

CAP.

800069746182555150374610425039423676

CAP.(LBS)

MODELNUMBER

DIM."S"

DIM."W"

DIM."X"

DIM."Y"

DIM."XX"

DIM."TL"

DIM."H.U.B."

WT.(LBS)

4000 JLT411 11" 17"30.3" 10.6"46.0"29.4" 10.3"44.4"28.6" 10.0"42.9"27.9" 9.7"41.5"32.2" 11.7"49.8"31.3" 11.4"48.1"30.5" 11.2"46.7"29.8" 11.0"45.4"29.2" 10.8"44.2"33.4" 11.7"50.8"30.7" 10.4"45.5"28.7" 10.9"41.5"

32.3" 11.4"49.7"24" 10" 3734000 JLT424 24" 30" 24" 4134000 JLT430 30" 36" 24" 4344000 JLT436 36" 42" 24" 4554000 JLT442 42" 48" 24" 4766000 JLT613 13" 21" 24" 519

TELESCOPING JIB LIFT

01-27-12

FORKPOCKETS

2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"2-1/2" X 5-1/2"3-1/2" X 7-1/2"

6000 JLT624 24" 32" 24" 5446000 JLT630 30" 38" 24" 5666000 JLT636 36" 44" 24" 5886000 JLT642 42" 50" 24" 6108000 JLT824 24" 32" 32" 6678000 JLT836 36" 44" 32" 7878000 JLT848 48" 56" 32" 12" 909

10"10"10"10"10"10"10"10"10"10"10"

3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"

E 74 4000 6000 8000D 64 4000 6000 8000C 54 4000 6000 8000B 44 4000 6000 8000A 34 4000 6000 8000

DIM."OAH"

19"19"19"19"19"19"19"19"19"19"20"20"22"

THIS CHART LISTS SAFE WORKING LOADSFOR THE JIB LIFT ONLY. IT DOES NOT

CONSIDER THE FORK TRUCK BEING USED.CONSULT THE FORK TRUCK MANUFACTURER

FOR SAFE LOAD CAPABILITIES WITHTHIS ATTACHMENT BEFORE USING.


Neenah, WI 54956-1642Phone (920) 722-0101


1

2

10-29-10

3

4

5

6

7

8

2

7

6

8

3

4

1

5

Alternate Hook Positions

Telescoping Boom

Boom Handle

Safety Swivel Hook

Fork Pockets

48" Safety Chain with Grab Hook

Spring Loaded Boom Lock

Angle Adjusting Pin

• Converts lift truck into a crane inexpensively• Moves cumbersome items your forks can't reach.• Crane reaches out and picks up from overhead.• Increases load height• Adjustable boom height and reach• Reaches through or over obstructions.

Pivoting jib lift lets you convert your standard lift truckinto a mobile crane in minutes at minimal cost. Lift loadshigher than your lift truck forks can reach. Pivoting boomadjusts from horizontal to 50°. Enjoy the convenience of

this versatile attachment without duplicating existingequipment ...and it's easy to use. One person can install

without removing forks. 48" safety chain ties jib lift totruck frame. Constructed of heavy structural steel tubing;

one swivel hook provided.

PIVOT BOOM JIB LIFT



SW

FEATURES• Handles long loads in closed trucks• High and long reaches for inaccessible areas• High underclearances and bulky load handling• Adjustable at 10° increments from horizontal to 50°• Safety chain secures jib lift to forklift truck

143-3/8" MAX

IMPORTANTTRUCK FORKS MUST

EXTEND THROUGH FULLLENGTH OF FORK TUBES

83-3/8" MIN

H.U.B.

H.U.B.

BOOM CONTRACTED

BOOM EXTENDEDXX

X

TL

TL


HOOKPOSITION

9


HOOKPOSITION

1



Y

Y

OAH

CENTER OFGRAVITY

CENTER OFGRAVITY

CENTER OF GRAVITY LOCATION

CAP.(LBS)

MODELNUMBER

DIM."S"

DIM."W"

DIM."TL"

DIM."H.U.B."

WT.(LBS)

4000 PB-JLT424 24" 30" 24" 18-1/2" 4914000 PB-JLT436 36" 44" 24" 19-1/2" 5886000 PB-JLT624 24" 32" 24" 19-1/2" 6406000 PB-JLT636 36" 44" 24" 23-1/2" 7188000 PB-JLT836 36" 44" 32" 27-1/2" 9668000 PB-JLT848 48" 56" 32" 27-1/2" 1025

PIVOT BOOM JIB LIFT

01-27-12

SINGLE HOOK CAPACITIES

HookPos.

123456789

HookPosition(inches)

8087-1/2

95102-1/2

110117-1/2

125132-1/2

140

4000LB.

CAP.

400035353167286826212413223520821949

6000LB.

CAP.

600053024750430239313619335331232923

8000LB.

CAP.

800069746182555150374610425039423676

E 74 4000 6000 8000D 64 4000 6000 8000C 54 4000 6000 8000B 44 4000 6000 8000A 34 4000 6000 8000

THIS CHART LISTS SAFE WORKING LOADSFOR THE JIB LIFT ONLY. IT DOES NOT

CONSIDER THE FORK TRUCK BEING USED.CONSULT THE FORK TRUCK MANUFACTURER

FOR SAFE LOAD CAPABILITIES WITHTHIS ATTACHMENT BEFORE USING.

FORKPOCKETS

2-1/2" X 5-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"3-1/2" X 7-1/2"

DIM."OAH"30-1/2"31-1/2"

32"36"

41-3/4"41-3/4"

DIM."X"

DIM."Y"

DIM."XX"

25.2"27.0"25.5"26.0"24.6"

26.7"16.7"16.2"17.2"19.7"17.4"

16.5"36.5"41.2"38.2"38.0"35.0"

39.7"


Neenah, WI 54956-1642Phone (920) 722-0101


8-16-02

PALLET LIFTER

Contrx Standard Pallet Lifters make your crane into an inexpensive forklift. You can afford palletlifting convenience at a small cost. Speed up handling and movement of pallet loads, loadingand unloading. Reach areas such as flat and gondola cars, open top trucks, and congestedareas with a pallet lifter. Contrx brand pallet lifters are designed to hang level when empty or

with a properly balanced load. See table on reverse side for capacities and dimensions.Contact your local dealer for custom dimensions.


Phone (920) 722-0101Fax (920) 725-1394

PALLET LIFTERDIMENSION & WEIGHT CHART

www.contrx.com4-1-08

Smaller pallets may be lifted as long as theircenter of gravity is located under the lifting bail.

Specify hook size when ordering to ensurecompatibility with lifting bail size.

G

A

B

F

Handle

LiftingBail

Center of gravityof lifter & load.

MODELPL524PL530PL536PL542PL548PL130PL136PL142PL148PL236PL242PL248PL336PL342PL348PL436PL442PL448PL636PL642PL648PL836PL842PL848

PL1036PL1042PL1048

CAP(lbs.)5005005005005001000100010001000200020002000300030003000400040004000600060006000800080008000

10,00010,00010,000

A(in.)243036424830364248364248364248364248364248364248364248

B(in.)121518212415182124182124182124182124182124182124182124

F(in.)202025252520252525252525252525252525272727272727272730

G(in.)484848484848484848484848484848484848484848484848484848


Neenah, WI 54956-1642Phone (920) 722-0101


11-19-02

BRIDGECRANES

DOUBLE GIRDERTOP RUNNING

• Double reduction helical gearmotor for reduced wear and long life

• Adjustable torque magnetic disc brake for smooth operation

• Machined steel crane and trolley wheels for smooth and quiet operation

• Top quality hoists matched to the duty required for each bridge crane

• Custom engineered to fit your application

• Independent traveling pendant• Variable frequency type drive motor control• Radio remote control operation• Travel limit switches, warning lights, & horn• 60 minute motors & special insulation• Catwalks & service platforms• Heat shields• Runway rails & beams

Available custom optionsStandard options


Neenah, WI 54956-1642Phone (920) 722-0101


11-19-02

TYPES OF STANDARD BRIDGE CRANESDOUBLE GIRDERTOP RUNNINGWITH DUALOUTRIGGERS

SINGLE GIRDERTOP RUNNINGWITH SINGLEOUTRIGGER

SINGLE GIRDERUNDER RUNNINGWITH DUALOUTRIGGERS

SINGLE GIRDERUNDER RUNNINGWITH NOOUTRIGGERS

SINGLE GIRDERTOP RUNNINGWITH CAPCHANNEL

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax

www.contrx.com

TERMS OF SALE

TERMS OF BILLING: NET 30 DAYS TO APPROVED ACCOUNTS 1 1/2% Interest Charged on Past Due over 39 days from date on Invoice. FREIGHT TERMS: All Products Shipped Freight Collect or Prepaid-3rd Party Billing. All shipments are made F.O.B Neenah, Wisconsin. When the shipment leaves our dock it becomes the property of the Distributor. Any claims for damage or shortages must be made by the Distributor. (SEE FORM CX11491) RETURNS: 20% restocking charge on all returns. Returns must be shipped freight Prepaid. SPECIALS: Specially fabricated orders are not returnable.

All merchandise is sold F.O.B. Contrx Factory, Neenah, WI. Title to the merchandise is transferred to the Distributor at the time the Carrier accepts the shipment. Any claims for loss, damage, or tracers for lost items in transit MUST BE FILED BY THE DISTRIBUTOR WITH THE CARRIER. Suitable copies of Bill of Lading will be furnished upon request if the Distributor has occasion to file a claim with the carrier. There are three types of claims that occur on shipments to customers. 1. Loss or short on delivery. 2. Visible damage at time of delivery. 3. Concealed damage noted after delivery. There are three steps to take before signing a carrier delivery receipt. 1. Count the number of pieces and compare against count on the freight bill. 2. Visually inspect each piece for damage. 3. Read the labels and packing slips to be sure the freight belongs to you. LOSS OR SHORT ON DELIVERY 1. If the shipment is not received within ten working days after the known ship date, contact CONTRX Customer Service for the shipping information necessary for you to file a tracer. 2. If a shipment is delivered short and the shortage is not delivered within 48 hours, contact CONTRX for the shipping information so you can file a tracer. VISIBLE DAMAGE AT TIME OF DELIVERY 1 DO NOT REFUSE THE SHIPMENT or return damaged merchandise to CONTRX without authorization. 2. The customer should immediately inspect the damage with the driver. 3. The specific damage should be noted on both the customers copy and the carrier copy of the freight bill. The driver should sign both copies. 4. Set the damaged merchandise aside and contact the carrier for an inspection. CONCEALED DAMAGE NOTED AFTER DELIVERY 1. Concealed damage must be reported to the carrier as soon as possible. 2. Call the Carrier for an inspection. 3. Follow the same procedure as for visible damage at the time of delivery. 4. Any freight transferred after delivery that may have concealed damage is not recoverable by the Carrier or CONTRX. FILING THE CLAIM 1. There are four basic documents necessary to support your claim. a. Delivery receipt with noted exceptions. b. Inspection report from the carrier. c. Cost of parts to repair the damage. (Repair Invoice) d. CONTRX Invoice showing the cost of the product. 2. There is a nine month statute from date of receipt for filing a loss or damage claim. 3. CONTRX Customer Service Department will provide any information or assistance to help resolve a loss or damage claim you have filed.

MEMO TO DISTRIBUTORS CONCERNING LOSS AND DAMAGE CLAIMS

FORM: CX11491

1. CONTRX Industries warrants products it manufactures against defects in materials and workmanship for a period of one year from date of receipt by the purchaser or his customer, or one year from time of completion of initial field installation if installed by CONTRX. CONTRX agrees to furnish the same or substantially similar replacement part (new or repaired) free of charge, F.O.B. site, providing the buyer gives immediate written notice of alleged defects and, if requested by CONTRX, returns the defective parts to our factory, freight collect, for our inspection and examination.

2. This warranty applies only to CONTRX equipment or materials which, after our inspection is determined to be defective either in material supplied or workmanship performed by CONTRX. Where equipment is furnished by CONTRX but not of its manufacture, CONTRX’S liability is limited to such adjustment as the actual manufacturer makes to CONTRX.

3. CONTRX will not be liable for the cost of repairs, alterations, or replacements or any expense connected therewith made or incurred by the purchaser or his agents or employees, except upon written authority from the CONTRX office.

4. This warranty is personal to purchaser only and applies only to equipment the purchaser has properly installed, operated and maintained in accordance with CONTRX’S written instructions.

5. CONTRX assumes no liability for any consequential damages suffered through the use or loss of use of its equipment.

6. This constitutes CONTRX’S sole warranty with respect to the equipment and material manufactured by itself. CONTRX makes no other warranty of any kind whatsoever, expressed or implied, and all implied warranties of merchantability and fitness for a particular purpose which exceed the aforementioned obligation are hereby disclaimed by CONTRX Industries.

CONTRX INDUSTRIES, INC. 1377 Kimberly Drive, Neenah, WI 54956 (920) 722 0101 Office (920) 725 1394 Fax

www.contrx.com

PRODUCT WARRANTY

• FLOOR MOUNTED JIB CRANES • PORTABLE JIB ... · PDF file• FLOOR MOUNTED JIB...

Documents

Transcript of • FLOOR MOUNTED JIB CRANES • PORTABLE JIB ... · PDF file• FLOOR MOUNTED JIB...