Established in January 2002. Business model is to provide high quality, extremely rugged and...
-
Upload
darin-draper -
Category
Documents
-
view
216 -
download
2
Transcript of Established in January 2002. Business model is to provide high quality, extremely rugged and...
Established in January 2002.
Business model is to provide high quality, extremely rugged and reliable speaker microphones to the land mobile radio (LMR) market, focusing on Public Safety, Emergency Response, Military and Industrial applications.
We offer two speaker microphone platforms (Sword and Juno), a PTT platform (Utah) and several audio accessories (Omaha Series). All major OEM radio platforms are supported.
See www.stonemountainltd.com for more details.
Stone Mountain, Ltd. Introduction
Juno™ Speaker Microphone
• Juno speaker microphone series.
• Sword speaker microphone series.
• Utah chest PTT series.
• Omaha audio accessory series.
Product Lines
• Designed for Law Enforcement, Military, Fire Fighting, Utility, and Industrial users.
• 50 mm. Mylar speaker.• Supports a full line of 2.5 mm., 3.5 mm.
and six pin Hirose connector accessories.
• Immersion rated to two meters for 60 minutes.
• 24 month warranty.
Sword Speaker Microphone
• Antenna incorporates Printed Circuit Flex Film Technology (PCFFT) .
• Antenna is included with speaker mic.• Micro miniature custom coax cable and
connectors.• Full six foot extended coil cable.• Supports a full line of 2.5 mm., 3.5 mm.
and six pin Hirose connector accessories.
• Supports 700 & 800MHz. frequency.• Immersion rated to two meters for 60
minutes.• 24 month warranty.
Sword ProBand Antenna Series
Sword TruBand Antenna Series
• Micro miniature custom coax cable and connectors.
• Full six foot extended coil cable.• Supports a full line of 2.5 mm., 3.5 mm.
and six pin Hirose connector accessories.• Supports VHF, UHF, 700, 800, and
900MHz. frequencies.• Antenna is purchased separately from
speaker Mic.• Immersion rated to two meters for 60
minutes.• 24 month warranty.
VHF 136MHz - 144MHzVHF 145MHz - 148MHzVHF 150MHz - 162MHzVHF 155MHz - 164MHz VHF 164MHz - 174MHz
UHF 400MHz - 449MHzUHF 450MHz - 469MHzUHF 470MHz - 512MHz
800 800MHz - 866MHz
900 902MHz - 960MHz
Sword TruBand Antenna Series
• Z-Axis design for manufacturability and ease of repair.
• Modular design to facilitate upgrading.
• Interchangeable components to minimize inventory.
• No soldered connections - All gold plated custom connectors and pressure contacts for reliability in harsh environments.
• Integrally molded buttons for environmental sealing.
• Two shot revolving platen overmolding provides comfortable rubber user interface.
Speaker Microphone Design Ideology
• Substrate is a custom engineered PC/ABS blend thermoplastic polymer.
• Overmold is a thermoplastic elastomer alloy designed especially for bonding to the substrate PC/ABS polymer.
• Molded concurrently in a two shot revolving platen overmolding process for optimum quality and part integrity.
• Allows emergency button, push to talk (PTT) and volume control interface buttons to be integrally molded to the case, resulting in unprecedented sealing capability.
Engineered Materials
• Intuitive button locations.• Ergonomic form factor.• Comfortable rubber interface.• Roman arch design allows extreme
compression loading in any direction.• Attractive design.• Form follows Function.
Form Factor
• Conventional forward acoustic speaker porting.
• Additional dual radial acoustic speaker porting - Allows speaker mic to be worn in any orientation without degradation to acoustic performance.
• Speaker cavity self draining feature.• No speaker cloth to trap dust/debris-
Clean speaker cavity by flushing with tap water.
• Superb acoustic performance and clarity throughout the entire life of the product.
Receive Audio System
• AllClear microphone porting system.• Protected 3.5mm. microphone
opening.• Sculpted, polished intake geometry
removes surface tension – Minimizes trapped water and debris.
• Enhances mic sensitivity.• Self clearing capability.• Integrally protective hood directs
falling water away from mic opening.• Maintains clear transmit audio even
when covered with water.
Microphone Porting - Sword
Microphone Porting - Juno
• AllClear microphone porting system.• Oversize 3.5mm. microphone opening.• Sculpted, polished intake geometry
removes surface tension – Minimizes trapped water and debris.
• Enhances mic sensitivity.• Self clearing capability.• Integrally molded ribs in protective
hood directs falling water away from mic opening.
• Maintains clear transmit audio even when covered with water.
• PTT– Large contact area.– Positive tactile response.– Intuitive location.
• Volume Control– Discrete high and low buttons. – Programmable on certain radio
models.• Emergency
– Recessed design coupled with custom 200 gm. and 320 gm. contact force switches to eliminate false emergencies.
Integrally Molded Buttons
Belt Clip
• Large, rugged design.• PC/ABS custom engineered polymer.• High quality stainless steel
components for reliability and corrosion resistance.
• 360° rotation with positive detents at every 45°.
• High closure force.• 180 degree lip for positive retention.• Accommodates any tactical gear,
turn out coat, etc.• Easy to replace and repair.
Belt Clip w/o screws - SMX25155
Belt Clip w/ screws – SMX26755
Custom O-Ring Seal Screws
• Custom designed and tooled.• Discrete low durometer silicon o-ring
seal.• Recessed screw head for mating o-
ring means no compression set - Maintains a reliable seal over the life of the product.
• Nickel plated to protect against corrosion in harsh environments.
• Standard Torx drive throughout for positive, repeatable engagement torque during installation.
• Reusable.
Seal Screw Assembly, K22xK14 – SMX19024
Seal Screw Assembly, K22xK6 – SMX19086
Speaker & Installation
• High quality Mylar speaker.• Heavy duty magnet and construction.• Miniature connector interface.• Attached to front cover with custom
designed and tooled pressure sensitive adhesive (PSA) component.
• Hermetically sealed via robotically dispensed engineering adhesive compound.
Dynamic Transfer Bars
• Overmolded dynamic transfer bars for emergency and PTT buttons.
• Ensures positive actuation over entire button user interface surface.
• Maintains tactile response throughout product life.
• Custom “ball and socket” mating interface - Ease of assembly and repair.
Sword PTT Transfer Bar – SMX19056
Emergency Transfer Bar – SMX19007
Custom Snap Dome Switches
• Custom designed and tooled.• 100% gold plated.• Side actuating snap domes in 200
gm. and 320 gm. contact force.• Pogo pin printed circuited board
(PCB) interface-No soldering/no wires.
• Allows Z-axis assembly.• Facilitates repair.• Custom “ball and socket” mating
interface - Ease of assembly and repair.
• Extensively tested in house and verified to one million actuations minimum.
320 gm – SMX19013Used for Volume Control
200 gm – SMX19506Used for Emergency Button
Front Cover Assembly – SMX19931
Transmit Audio System
• Four component custom designed and tooled proprietary microphone acoustic gasket assembly.
• Custom designed and tooled silicon rubber acoustic boot.
• High sensitivity omni directional microphone.
• Miniature connector interface for ease of assembly and repair - No soldering.
• Custom designed and tooled silicon rubber sound port.
• Superb transmit audio and clarity.
Microphone Assembly – SMX19688
Sword Sound Port – SMX19058
Microphone Boot –
SMX19687
Microphone Gasket – SMX19770
Rear Cover Assembly
• PC/ABS custom engineered polymer.• Compression molded, custom
designed and tooled low durometer silicon rubber environmental seal.
• Low compression set speaker support component.
• Labyrinth design venting system with waterproof gaskets.
• 100% of all seal interface surfaces are highly polished for reliable environmental sealing.
• Discrete sub assembly supports Z-axis assembly - Ease of repair.
Rear Cover Assembly – SMX19061
Main PCB Assembly
• Self aligning via integrally molded mating geometry in the front cover.
• 100% surface mount technology (SMT) components.
• 100% gold plated for optimum conductivity, performance and reliability in harsh environments.
• No hand soldering - Easy to repair.• All Main PCB’s will accommodate every
SML cable/accessory option with existing SMT connectors - Easy to upgrade.
• Clean, efficient design.
Cable Attachment & Accessories
• Supports system accessory option upgrade.
• Aircraft aluminum grade cable clamps, includes holes for easy release and repair.
• Integrally overmolded waterproof accessory interfaces in the cable.
• Options include 2.5 mm, 3.5 mm. and 6 pin Hirose.
• Miniature connectors throughout - No soldering.
Cable – Strain Relief, Sealing & Performance • Custom designed, machined high strength
brass ferrules, crimped to the cable.• 50K cycle endurance rating.• Overmolded with custom engineered
thermoplastic polyurethane (TPU).
• Designed using finite element analysis (FEA) for optimized strength to weight ratio.
• Integrally molded o-ring seal interfaces with high quality silicon rubber o-ring seals.
• Integrally molded locking geometry prevents rotation of cable and subsequent damage to the electrical connections.
• 200 Newton minimum rated pull strength.
Radio Connector (RC) Design
• All RC’s are either custom tooled by SML or sourced from quality OEM RC suppliers.
• Most SML tooled RC’s are fastened together using seal screws - No snap fits.
• All SML tooled RC’s include miniature connectors - No soldered wires.
• Most SML tooled RC’s include multiple molded silicon components for redundant environmental sealing.
• Custom three layer PSA includes silicon and acrylic adhesive components.
• All seal surfaces 100% polished.
Radio Connector (RC) PCB
• All RC PCB’s are either custom tooled by SML or sourced from quality OEM RC suppliers.
• All SML tooled PCB’s are 100% surface mount technology (SMT).
• All SML tooled PCB’s are 100% gold plated for optimum reliability in harsh environments.
• All SML tooled PCB’s are fully connectorized for ease of assembly and repair.
• High strength, gold plated pogo pins for long, reliable life.
ProBand Antenna Technology
• Printed Circuit Flex Film Technology (PCFFT) allows miniaturization of the physical antenna envelope.
• High RF performance.• Bendable and durable.• Will not corrode or rust.• Waterproof.• Low profile.• Light weight.• Supports 800MHz., with 700MHz and
900MHz. pending.
ProBand Assembly
• Custom engineered thermoplastic elastomer alloy overmolded antenna assembly.
• High quality, low durometer discrete silicon o-ring sealing component.
• Antenna included with speaker microphone - No need to dismantle radio antenna.
• No soldered connections for ease of repair and high reliability.
• Micro miniature, low loss coax connectors and cable allow full six foot extended coil cord.
Plated Rear Cover – SMX19875
TruBand Assembly
• Replaceable injection molded 1/4 wave helical antenna.
• High quality, low durometer discrete silicon o-ring sealing component.
• No soldered connections for ease of repair and high reliability.
• Replaceable gold plated surface mount RF PCB.
• Micro miniature, low loss coax connectors and cable allow full six foot extended coil cord.
• VHF, UHF, 800MHz. and 900MHz. antennas.
Plated TruBand Rear Cover Assembly – SMX25072
RF Plating
• Cutting edge vacuum metallization plating process using copper and nickel materials.
• High conductivity.• Excellent shielding.• Will not rust, corrode or degrade in
corrosive environments.• Highest quality.
Sword Plated Front Cover – SMX19933
Cable Assemblies
• Six foot fully extended cable assembly.
• 100% fully connectorized signal and coax interface to speaker mic head and all SML tooled radio connectors - No soldered connections.
• Integrally overmolded, environmentally sealed accessory interfaces in the cable.
• Options include plain, 2.5 mm., 3.5 mm. and six pin Hirose.
• Rugged 5.5mm. diameter OD cable – Industry’s largest.
• Absolute highest quality, most rugged cable assembly available.
Available Options
• ProGain - User adjustable microphone gain system.
• AGC - Automatic Gain Control feature.
• Stainless steel knurled thumb screw.
• Interface to various OEM headsets, SCBA’s, etc.
• Standard or half length cables (most models).
ProGainTM System
• Allows the user to custom attenuate the speaker mic Tx audio microphone gain.
• Easy to access, sealed adjustable gain potentiometer.
• Maintains system environmental seal/immersion rating.
• Adjust microphone gain from maximum to minimum transmit power – Allowing close quarter communications by eliminating feedback.
• Simply remove the belt clip via four T6 Torx fasteners - Adjust mic gain with a small screw driver.
• Available on both Sword and Juno.
AGC - Automatic Gain Control
• Unique to SML• Mounts to main speaker mic PCB.• Custom tunable via software inputs.• Automatically adjusts the
microphone sensitivity and provides a consistent level of receive audio
• Useful If the user is whispering, shouting, or if background noise such as wind or industrial noise is present.
• Increases performance and addresses interface problems typical with accessories such as headsets and SCBA communication systems.
• Available on Sword.
Sword Technical Specifications
Microphone Element Omni directional Microphone Sensitivity -40 dBV (0dB=1V/Pa) Speaker Diameter 2.0” (50 mm) Speaker Output Power ½ to 1 W (dependent on radio brand/model) Speaker Output Level (SPL) 93 to 100 dB SPL (dependent on radio brand/model) Operating Voltage Range 5.0 to 9.0 VDC (microphone) Female Accessory Jacks 3.5 mm & 2.5 mm for remote Rx audio or 6 pin Hirose HR10A 7R 6S
“Locking Quick Disconnect” for remote Tx/Microphone, Rx/Earphone and PTT functions
Frequency Response 300 – 3000 Hz Distortion 4% (speaker) Dimensions 3⅜” L x 2⅝” W x 1” H (84.8 mm x 66.0 mm x 26.8 mm) Weight 7.5 oz (212 gm) Operating Temperature -30°C to +60°C Storage Temperature -57°C to +80°C Volume Control Up (+) and Down (-) buttons for adjustable volume control Rotating Clothing Clip 360°with positive detents at every 45° Cable Assembly Flex Life 50,000 cycles
Cable Assembly Pull Strength1 45 lbs. (200N) tensile strength, in line with speaker mic Cable Assembly Pull Strength2 45 lbs. (200N) tensile strength, perpendicular to speaker mic Immersion Rating3 One (1) meters for thirty (30) minutes Mil-Std 810C, D, E & F Specs Designed to meet or exceed Low Pressure 500.4/I & II Yes High Temp 501.4/I & II Yes Low Temp 502.4/I & II Yes Blowing Rain 506.4/I3 Yes Leakage 512.4/I3 Yes Humidity 507.4/II Yes Salt Fog 509.4/I Yes Blowing Dust 510.4/I Yes Vibration 514.4/I/CAT 1 & 104 Yes Shock 516.5/I & IV Yes Temp Shock 503.4/I Yes Solar Radiation 505.4/II Yes
Footnotes:1 Straight pull strength, at speaker microphone end2 Right angle pull strength, at speaker microphone end3 Speaker mic only, excludes radio device connector4 Curve W