8830005-D-TRM-4Title: 8830005-D-TRM-4.indd Created Date: 8/21/2014 11:02:27 AM
Transcript of 8830005-D-TRM-4Title: 8830005-D-TRM-4.indd Created Date: 8/21/2014 11:02:27 AM
-
8830005 - REV D • 7/14 PAGE 1 OF 2
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com
TRM-4 Twin Relay Module
Features
Stock Number: 1430824
S2930
ApplicationThe TRM-4 is compatible with Potter’s PFC-6000 series and PFC-8500 addressable fi re alarm control panels. The TRM-4 is a relay module that is programmed to activate in correlation with initiating devices, such as detectors and pull stations. The TRM-4 can be used for applications such as elevator recall, AHU shutdown, or where general purpose relays are needed.
Description The TRM-4 module uses one (1) address on an SLC Loop. The module has two (2), Isolated Form C relay contacts that transfer simultaneously when the device is activated. The TRM-4 module includes one red LED that fl ashes when the device is being polled by the control panel.
Technical Specifi cations Operating Voltage 22.0-24.0VMax SLC Standby Current 325 µAMax SLC Alarm Current 1mAContact Output Style Two (2) Form CContact Rating (Resistive) 2A @ 24 VDC / 0.5A @ 125VACOperating Tempurature Range 32 to 120ºF (0 to 49ºC)Operating Humidity Range 0 to 93% (non-condensing)Max no. of Modules per Loop 127 units
Dimensions 4.17” (106mm)L × 4.17” (106mm)W × 1.14” (29mm)
Mounting Options Standard 4” Square orDouble Gang BoxShipping Weight 0.6 lbs
• Two (2) Isolated Sets of Form C Contacts• Powered directly from 2-wire SLC loop. • No additional power required.• SLC Class A (Style 6,7) & Class B (Style4)• Mounts on a standard 4” or double gang box• Wiring terminals accessible when mounted in box• Wiring terminals accept 22 to 14 AWG• Product includes a 5 year warranty
7165-0328:0196
-
8830005 - REV D • 7/14 PAGE 2 OF 2
Potter Electric Signal Company, LLC • St. Louis, MO • Tech Support: 866-956-0988 / Customer Service: 866-572-3005 • www.pottersignal.com
TRM-4Twin Relay Module
Installation Using Compatible Electrical Box
Wiring Diagram
Setting the Address
Each SLC device must be assigned an address prior to installation. The address is set using either the hand held device programmer or the addressing feature on the PFC-6000 /PFC-8500 Series control panels.
Before connecting a device to the SLC loop, take the following precautions to prevent potential damage to the panel or device:1. Power to the device is removed2. Field wiring is correctly installed.3. Field wiring has no open or short circuits.
S-
S+
SLC Loop
To Next Module
From FACP or Previous Module
Twin Relay ModuleModel No. TRM-4 LED
NO1
C1
NC1
NO2
C2
NC2
Contact Rating:24VDC / 2.0A125VAC / .5A Normally Open 1
Common 1
Normally Closed 1
Normally Open 2
Common 2
Normally Closed 2
DWG. #593-17
It is possible that the relay contacts on the TRM-4 may be shipped in the non-normal / activated state. To ensure that the internal relays are set to the normal state, connect the module to the SLC loop and reset the control panel before terminating the wiring to the dry relay contacts.
Normally Open Normally ClosedContact 1 C1 & NO1 C1 & NC1Contact 2 C2 & NO2 C2 & NC2