Post on 26-Mar-2015
www.Build-It-Yourself.com
Soda Bottle Rocket Launcher
www.Build-It-Yourself.com
Tools and Materials
8 ½”x11” 20lb copier paper8 ½”x11” 64lb card stock8 ½”x11” cardboardFoamie sheets
Rubber bandsPaperclipsCoffee stirrer sticksStrawsScotch tapeMasking tape
ScissorsGlue gunColored pencils12” ruler
www.Build-It-Yourself.com
Launcher
You can get these parts from Home Depot for less than $5.- 3-foot long ½” PVC pipe.- ½” Right Angle PVC pipe coupling- Block of wood 10”x 4”x 1”- Two 1” sheet rock screws.- One ½” pipe hanger - 2-liter soda bottle.
The wood block helps keep the launcher stable.
(Even thought it ‘s called ½” PVC pipe, it is actually 5/8” on the inside and 7/8” on the outside diameters.)
www.Build-It-Yourself.com
Launcher
Cut two 1-foot long pipe sections.If you get the PVC pipe from Home Depot, you can usually cut the pipe sections there with a hack saw or pipe cutter. If not you will need a hack saw.
Connect the PVC pipes and the soda bottle.
www.Build-It-Yourself.com
Launcher
Blast off!!!
www.Build-It-Yourself.com
FuselageYou can use thin card stock or 22lb weight paper (typical printer paper.)
Roll an 8.5” x 11” paper around a ½” PVC pipe. Tape this paper to the pipe. Use small 1” sections of tape. It is easier to control small tape pieces.
Then wrap a second paper around the paper that is taped. This will make your rocket fuselage have minimum friction with the pipe when it takes off.
Tape the second rolled paper and slip it off the pipe.
11”
½” PVC pipe
www.Build-It-Yourself.com
Fuselage
Flatten and cut a point on one end.
Tape that end so it makes an air tight tube when you blow in the open end.
www.Build-It-Yourself.com
Nose Cone
Wrap a 6” x 4” piece of Foamie into a cone.
Hot glue or tape the cone shape.
Cut the open end of the cone so it is round.
6”
4”
3”
www.Build-It-Yourself.com
Nose Cone + Fuselage
Hot glue the nose cone to the fuselage.
www.Build-It-Yourself.com
Tail Fins Simple
Start with a 8.5” x 11” card stock or 22lb paper.
11”
8.5”
Fold in half,Hamburger style. Cut at the fold.
Bend in half and cut at the fold.
Fold the two strips in the middle and cut at the fold.
Mark a straight line from corner to corner. Put the two pieces exactly on top of each other.
www.Build-It-Yourself.com
Tail Fins Simple
Cut along the diagonal line and you will have 4 symmetrical fins.
Score and fold a flange about ¼” along the long edge of the triangle.
Then cut a small slit from the edge to the fold.
Bend the top flange to the left and the bottom flange to the right.
You need to do this for all 4 fins.
You need to make flanges on each fin so you can tape or hot glue them to your rocket fuselage.
www.Build-It-Yourself.com
Tail Fins Rugged
Build these fins instead of the simple fins if you want really rugged fins.
11”
8.5”
Fold in half.Hamburger style
Cut the two halves Fold the two halves in the middle.
www.Build-It-Yourself.com
Tail Fins Rugged
Fold the two halves in the middle.
Cut the two folded halves in the middle.
The goal is to make 4 fins that are exactly symmetrical!
Cut the four rectangles into four equal triangles.
www.Build-It-Yourself.com
Tail Fins Rugged
The goal is to make 4 fins that are exactly symmetrical!
Cut the four fins along the dotted line.
Now you need to fold flanges so you can glue or tape the fins to the fuselage.
www.Build-It-Yourself.com
Nose Cone + Fuselage + Fins
Hot glue the fins to the fuselage.
If you want your rocket to fly straight you will need to mount your fins at right angles. You can make a cross hair template to ensure good alignment.
Try mounting your fins so they will make your rocket spin. Your rocket may not go quite as high but it may travel in a straighter line if it is spinning like a bullet.
Top View
www.Build-It-Yourself.com
Nose Cone + Fuselage + Fins
www.Build-It-Yourself.com
Hall of Fame Rockets
www.Build-It-Yourself.com
Nose Cone + Fuselage + Wings + Tail
You could add wings and a tail instead of fins and launch a glider. Before you launch it, make sure it glides well. You can position the wings forward or backward to control the center of gravity. You could also cut elevators to control loops.
You can stiffen the wings by folding the leading edge or taping a coffee stirrer stick to the leading edge.
www.Build-It-Yourself.com
Decorate Your Plane
www.Build-It-Yourself.com
Air Show
Competitions:1) Best looking (scale of 1-10).2) Furthest distance.3) Most accurate.4) Highest flight.5) Most interesting flight (scale of 1-
10).