Post on 31-May-2020
WINS H-TECFIRE PROTECTION
PANEL(Calcium Silicate)
Page 1
WINS H-TEC FIRE PROTECTION PANELPHYSICAL AND MECHANICAL PROPERTIES
Test Description Standard Test Result
Density
Resistance to impact
Moisture content
Dimension
Surface condition
Sound transmission loss
BS EN 1170-6:1998
BS 5669 :Part 1:1989, Clause 21
BS EN 772:1993
BS 5669:Part1:1989, Clause 8
By direct measurement
1.05g/cm3
Class A
12.35%
Average thickness: 8.87mm
No visible damage
13.98MPa
Dimensional changesassociated with changesin relative humidity
Tensile strength andelongation at break
BS 2782:Part 10:Method 1003:1977
BS EN 318:2002
BS 5669 :Part 1:1989,Clause 19
Increase in mass(water absorption)& thickness(swelling)
Microscopic examinationof bulk materials
In-house methodsG-T-023 & G-T-028
BS 2782:Part 10:Method 1005:1997
BS 2750 Part 3:1995
Flexural strength
Water absorption: 34.99%;Swelling: 0.08%
55dB
Non-asbestos
Length change:generally within 0.02%
Tensile strength: 6.98MPa
Elongation at break: 0.14%
Thickness change:generally within 0.12%
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.1:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
HORIZONTAL ENCLOSURE SYSTEM FOR :4 HOURS INTEGRITY
4 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 2
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm.
6 Steel cable tray
7 Rock wool 1 layer of 100mm thick with nominal density of 80Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
Legend :
1
35
4
2
7
8
6
7
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.2:THREE-SIDED WINS H-TEC FIRE PROTECTION PANEL
HORIZONTAL ENCLOSURE SYSTEM FOR :4 HOURS INTEGRITY
4 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 3
9
7
1 2 7
3
57
48
6
6
1 2 4
7
5
107
978
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm.
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 100mm thick with nominal density of 80Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Legend :
10
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.3:TWO-SIDED WINS H-TEC FIRE PROTECTION PANEL
ENCLOSURE SYSTEM FOR :4 HOURS INTEGRITY
4 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 4
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 100mm thick with nominal density of 80Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
3
9
6
8
5
7
21
7
7
4
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.4:ONE-SIDED WINS H-TEC FIRE PROTECTION PANEL
ENCLOSURE SYSTEM FOR :4 HOURS INTEGRITY
4 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 5
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 100mm thick with nominal density of 80Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
39
4
6
51 2 87
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.5:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
VERTICAL ENCLOSURE SYSTEM FOR :4 HOURS INTEGRITY
4 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 6
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 Steel cable tray
6 M4 Self-tapping screw at nominal 200mm centers
7 Rock wool 1 layer of 100mm thick with nominal density of 80Kg/m3
8 General E&M services. e.g. cable trunking and steel pipe etc.
9 Steel angle minimum 25mmx25mmx0.9mm thick fasten the service duct to the wall at nominal 1220mm centers.
Construction wall
Concrete �oor
Legend :
10
11
7
2
1
3
10
4
6
11
39
8
7
5
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.6:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
HORIZONTAL ENCLOSURE SYSTEM FOR :2 HOURS INTEGRITY
2 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 7
1
35
4
2
7
8
6
9
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm.
6 Steel cable tray
7 Rock wool 1 layer of 50mm thick with nominal density of 110Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.7:THREE-SIDED WINS H-TEC FIRE PROTECTION PANEL
ENCLOSURE SYSTEM FOR :2 HOURS INTEGRITY
2 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 8
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm.
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 50mm thick with nominal density of 110Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Legend :
10
9
7
1 2 7
3
57
48
6
6
1 2 4
7
5
107
978
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.8:TWO-SIDED WINS H-TEC FIRE PROTECTION PANEL
ENCLOSURE SYSTEM FOR :2 HOURS INTEGRITY
2 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 9
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 50mm thick with nominal density of 110Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
3
9
6
8
5
7
21
7
7
4
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.9:ONE-SIDED WINS H-TEC FIRE PROTECTION PANEL
ENCLOSURE SYSTEM FOR :2 HOURS INTEGRITY
2 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 10
39
4
6
51 2 87
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 M4 Self-tapping screw at nominal 200mm centers
6 M6 all steel expanding �xing at 500mm nominal centers
7 Rock wool 1 layer of 50mm thick with nominal density of 110Kg/m3
8 Steel angle minimum 25mmx25mmx0.6mm thick
9 General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
FIG. NO.10:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
VERTICAL ENCLOSURE SYSTEM FOR :2 HOURS INTEGRITY
2 HOURS INSULATIONIN ACCORDANCE WITH BS EN 1364-2:1999, BS EN 1364-1:1999
Page 11
1 1 layer of WINS H-TEC FIRE PROTECTION PANEL of 9mm thick
2 1 layer of WINS H-TEC FIRE PROTECTION PANEL FILLET 100mm width of 9mm thick positioned all board joints, except the corner longitudinal joints.
3 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
4 Steel channel collar, 32mmx50mmx32mmx0.5mm thick at butt joints at nominal 1220mm. Sizes may be larger to suit board and rock wool thickness
5 Steel cable tray
6 M4 Self-tapping screw at nominal 200mm centers
7 Rock wool 1 layer of 50mm thick with nominal density of 110Kg/m3
8 General E&M services. e.g. cable trunking and steel pipe etc.
9 Steel angle minimum 25mmx25mmx0.9mm thick fasten the service duct to the wall at nominal 1220mm centers.
Construction wall
Concrete �oor
Legend :
10
11
7
2
1
3
10
4
6
11
39
8
7
5
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance withBS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 1:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
HORIZONTAL ENCLOSURE SYSTEM
Page 12
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Steel angle minimum 50x50x0.9mm thick fasten the service duct to the wall at nominal 1200mm centers
Construction wall
Concrete �oor
C-channel 50x50x50x0.6mm thick
Access panel not exceeding 610mmx610mm
Legend :
10
11
12
13
14
15
16
ACCESSPANEL
(OPTIONAL)
1
15
9
16
35
4
2 6
7
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance withBS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 2: THREE-SIDED CONSTRUCTION FROM FLOOR SOFFIT
FIG. NO.2: THREE-SIDED CONSTRUCTION FROM SIDE WALL
Page 13
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Legend :
10
11
4 HRS. INTEGRITY
ACCESSPANEL
(OPTIONAL)
ACCESSPANEL
(OPTIONAL)
4
487
87
10
1 2 5 9
410
1 2 5 9 9
4
5
4
5
4 HRS. INTEGRITY
ACCESSPANEL
(OPTIONAL)
ACCESSPANEL
(OPTIONAL)
81 2
5 7
10911
81
5
72
4
1 2 910
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
Page 14
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at Fig nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
10
4 hours �re rating, integrity in accordance withBS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 3:TWO-SIDED WINS H-TEC FIRE PROTECTION PANEL ENCLOSURE SYSTEM
ACCESSPANEL
(OPTIONAL)
4
10
87
5921
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance withBS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 4:ONE-SIDED WINS H-TEC FIRE PROTECTION PANEL ENCLOSURE SYSTEM
Page 15
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at Fig nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Legend :
10
4
10
5
8
91 2 7
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Steel angle minimum 50x50x0.9mm thick fasten the serviceduct to the wall at nominal 1200mm centers
Construction wall
Concrete �oor
C-channel 50x50x50x0.6mm thick
Access panel not exceeding 610mmx610mm
Legend :
10
11
12
13
14
15
16
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance withBS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 5:FOUR-SIDED WINS H-TEC FIRE PROTECTION PANEL
VERTICAL ENCLOSURE SYSTEM
Page 16
ACCESSPANEL
(OPTIONAL)
6
2
1
15
13
5
9
14
4
1216
10
1 WINS H-Tec �re protection panel, 9mm thick
2 WINS H-Tec �re protection �llet, 100mm width, 9mm thick (inside or outside) positioned all board joints, except the corner longitudinal joints
3 Enclosure support, steel C-channel or L-angles
4 Steel hanger rod at nominal 1000mm centres sizes according to limiting stress
5 Steel channel collar, 32x50x0.5mm thick at butt joints at nominal 1220mm centers
6 Steel cable tray
7 Steel angle minimum 25x25x0.6mm thick
8 M6 all steel expanding �xing at 500mm nominal centers
9 M4 Self-tapping screw at nominal 200mm centers
General E&M services. e.g. cable trunking and steel pipe etc.
Cantilever arm at maximum 1250mm centers
Steel angle minimum 50x50x0.9mm thick fasten the serviceduct to the wall at nominal 1200mm centers
Construction wall
Concrete �oor
C-channel 50x50x50x0.6mm thick
Access panel not exceeding 610mmx610mm
Steel stud channel 32x50x32x0.5mm thick
Legend :
10
11
12
13
14
15
16
17
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordancewith BS EN 1364-2:1999, BS EN 1364-1:2015
FIG. NO. 6:ACCESS PANEL DETAIL
Page 17
ACCESSPANEL
OPTIONAL
1
15
9
163
4
2
close open
217
15
15
171
16
9
WINS ACCESS PANEL
A.P. 16
9
1 Wins H-tec �re protection panel, 9mm thick
2 Wins H-tec �re protection panel �llet, 100mm width, 9mm thick (inside or outside)
3 Enclosure support, steel c-channel or l-angles
4 steel hanger rod at nominal 1000mm centers sizes according to limiting stress, I.E. < 10 N/MM²
5 Steel channel collar, 32x50x0.5mm thick. Sizes may be larger to suit panel and mineral wood thickness
6 Steel cable tray
7 Mineral wool, 2 layers of 50mm thick with nominal density of 80 KG/M³
8 Access panel (optional)
9 M4 self-tapping screw at nominal 200mm centers
10 Steel angle minimum 25x25x0.6mm thick
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 18
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
close
open
ACCESS PANEL(OPTIONAL)
1
4
2
3
5
76
9
8
10
Fig1
FOUR-SIDED WINS 9MM THICK H-TEC FIRE PROTECTION PANELHORIZONTAL ENCLOSURE SYSTEM WITH ACCESS PANEL (OPTIONAL)
1 Wins H-tec �re protection panel, 9mm thick
2 Wins H-tec �re protection panel �llet, 100mm width, 9mm thick (inside or outside)
3 Steel channel collar, minimum 32x50x0.5mm thick at butt joints of nominal 1220mm centers
4 M4 self-tapping screw at nominal 200mm centers
5 Threaded rod hanger stress not exceed 10 N/MM², �xed to the wall
6 Steel angle, miniumum 50x50x0.9mm thick fasten the service duct to the wall at nominal 1220mm centers
7 General E&M services. E.G. Cable trunking and steel pipes, etc.
8 Mineral wool, 2 layers of 50mm thick with nominal density of 80 KG/M³
9 Construction wall
10 Concrete �oor
11 Steel angle minimum 25x25x0.6mm thick
12 Access panel (optional)
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 19
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
close
open
ACCESS PANEL(OPTIONAL)
78
2
1
5
4
6
9
3
10
4
512
11
Fig2
FOUR-SIDED WINS 9MM THICK H-TEC FIRE PROTECTION PANELVERTICAL ENCLOSURE SYSTEM WITH ACCESS PANEL (OPTIONAL)
1 Wins H-Tec �re protection panel, 9mm thick
2 Wins H-Tec �re protection panel �llet, 100mm width, 9mm thick (inside or outside)
3 M6 all steel expanding �xing at 500mm nominal centers
4 Steel channel collar, minimum 32x50x0.5mm thick at butt joints of nominal 1220mm centers
5 M4 self-tapping screw at nominal 200mm centers
6 Threaded rod hanger stress not exceed 10 N/MM², �xed to the wall
7 Steel angle minimum 25x25x0.6mm thick
8 General E&M services. E.G. Cable trunking and steel pipes, etc.
9 Mineral wool, 2 layers of 50mm thick with nominal density of 80 KG/M³
10 Cantilever arm at maximum 1250mm center
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 20
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
ACCESSPANEL
(OPTIONAL)
ACCESSPANEL
(OPTIONAL)
1
82
2 95473
8
1 9 52
7
36
54
6
4
6
7 7
ACCESSPANEL
(OPTIONAL)
ACCESSPANEL
(OPTIONAL)
3
1
295748
210
31 2 9
7
28
12527
6
Fig3
THREE-SIDED CONSTRUCTION FROM FLOOR SOFFITWITH ACCESS PANEL (OPTIONAL)
Fig3
THREE-SIDED CONSTRUCTION FROM SIDE WALLWITH ACCESS PANEL (OPTIONAL)
1 Wins H-Tec �re protection panel, 9mm thick
2 Wins H-Tec �re protection panel �llet, 100mm width, 9mm thick (inside or outside)
3 M6 all steel expanding �xing at 500mm nominal centers
4 Steel channel collar, minimum 32x50x0.5mm thick at butt joints of nominal 1220mm centers
5 M4 self-tapping screw at nominal 200mm centers
6 Threaded rod hanger stress not exceed 10 N/MM², �xed to the wall
7 Steel angle minimum 25x25x0.6mm thick
8 General E&M services. E.G. Cable trunking and steel pipes, etc.
9 Mineral wool, 2 layers of 50mm thick with nominal density of 80 KG/M³
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 21
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
ACCESS PANEL(OPTIONAL)
6
8
13 2 9
5247
7
Fig4
TWO-SIDED WINS 9MM THICK H-TEC FIRE PROTECTION PANELENCLOSURE SYSTEM WITH ACCESS PANEL (OPTIONAL)
1 Wins H-Tec �re protection panel, 9mm thick
2 Wins H-Tec �re protection panel �llet, 100mm width, 9mm thick (inside or outside)
3 M6 all steel expanding �xing at 500mm nominal centers
4 Steel channel collar, minimum 32x50x0.5mm thick at butt joints of nominal 1220mm centers
5 M4 self-tapping screw at nominal 200mm centers
6 Threaded rod hanger stress not exceed 10 N/MM², �xed to the wall
7 Steel angle minimum 25x25x0.6mm thick
8 General E&M services. E.G. Cable trunking and steel pipes, etc.
9 Mineral wool, 2 layers of 50mm thick with nominal density of 80 KG/M³
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 22
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
ACCESS PANEL(OPTIONAL)
684
3
5 12 9 7
Fig5
ONE-SIDED WINS 9MM THICK H-TEC FIRE PROTECTION PANELENCLOSURE SYSTEM WITH ACCESS PANEL (OPTIONAL)
1 Wins H-Tec �re protection panel, 9mm thick
2 Steel C-Channel at 610mm spacing 32x50x32x0.5mm thick
3 Furring channel / perimeter C-Channel 25x50x25x0.5mm thick
4 Steel wire hanger @1000mm c/c
5 Panel joints, all gaps sealed with intumescent sealant
6 Wins H-Tec �re protection panel �llet, 100mm width, 9mm thick
7 Self tapping screws at nominal 200mm centres
8 Rockwool-2 layers of 50mm thk (80KG/M³ )
9 Sti�ener galvanised steel C-Channel opening, 75x50x75x0.5mm thick
10 Access panel (optional, all panel surfaces)
Legend :
WINS H-TEC FIRE PROTECTION PANEL9mm THICK ENCLOSURE SYSTEM
Page 23
1 hour Fire Rating, Integrity and Insulation in accordancewith BS EN 1364-2:1999, BS EN 1364-1:1999
CLOSE
OPEN
9
6
10
3
3
1
6
7 1
8
WINS ACCESS PANELFig6
WINS H-TEC FIRE PROTECTION PANEL9mm THICK PARTITION SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance with BS EN 1364-1:2015
Page 24
1 Wall
2 Wins H-Tec Fire Protection Panel, 9mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 9mm thick, 100mm width
9 Access Panel (optional, any panel surface)
Steel stud channel 50x50x50x0.6mm thick
Legend :
10
closeopen
5
46
8
32
7
9
8
10
1
2
5
Access Port
3
WINS H-TEC FIRE PROTECTION PANEL9mm THICK PARTITION SYSTEM
4 hours �re rating, integrity in accordance with BS EN 1364-1:2015
Page 25
1 Wall
2 Wins H-Tec Fire Protection Panel, 9mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 9mm thick, 100mm width
Legend :
5
46
83
2
7
1
3
WINS H-TEC FIRE PROTECTION PANEL9mm THICK PARTITION SYSTEM
4 hours �re rating, integrity and insulation in accordance with BS EN 1364-1:2015
Page 26
1 Wall
2 Wins H-Tec Fire Protection Panel, 9mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 9mm thick, 100mm width
9 Rock wool density 80kg/m3 by 50mm thick
Legend :
5
46
8
32
7
1
3
9
9
WINS H-TEC FIRE PROTECTION PANEL12mm THICK PARTITION SYSTEM WITH ACCESS PANEL
4 hours �re rating, integrity in accordance with BS EN 1364-1:2015
Page 27
1 Wall
2 Wins H-Tec Fire Protection Panel, 12mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 12mm thick, 100mm width
9 Access Panel (optional, any panel surface)
Steel stud channel 50x50x50x0.6mm thick
Legend :
10
closeopen
5
46
8
32
7
9
8
10
1
2
5
Access Port
3
WINS H-TEC FIRE PROTECTION PANEL12mm THICK PARTITION SYSTEM
4 hours �re rating, integrity in accordance with BS EN 1364-1:2015
Page 28
1 Wall
2 Wins H-Tec Fire Protection Panel, 12mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 12mm thick, 100mm width
Legend :
5
46
83
2
7
1
3
WINS H-TEC FIRE PROTECTION PANEL12mm THICK PARTITION SYSTEM
1 hour �re rating, integrity and insulation in accordance with BS EN 1364-1:1999
Page 29
1 Wall
2 Wins H-Tec Fire Protection Panel 12mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Access Panel (any panel surface)
9 Rock wool density 80kg/m³ by 50mm thick
10 Steel stud channel 75x50x75x0.8mm thick
Legend :
closeopen
5
46
32
7
1
3
9
9
8
10
2
5
Access Port
WINS H-TEC FIRE PROTECTION PANEL12mm THICK PARTITION SYSTEM
4 hours �re rating, integrity and insulation in accordance with BS EN 1364-1:2015
Page 30
1 Wall
2 Wins H-Tec Fire Protection Panel, 12mm thick
3 Steel stud channel 32x50x32x0.5mm thick, @610mm c/c
4 Ceiling �oor perimeter steel channel 24x50x24x0.5mm
5 M4 Self-tapping screw, @200mm c/c
6 M6 steel anchor bolt, @610mm c/c
7 Board Joint, sealed with �re retardant sealant
8 Wins H-Tec Fire Protection Panel Fillet, 12mm thick, 100mm width
9 Rock wool density 80kg/m3 by 50mm thick
Legend :
5
46
8
32
7
1
3
9
9
1 Wins H-Tec �re protection panel 9mm thick
2 Steel C-Channel at 610mm spacing 32x50x32x0.5mm thick
3 Furring channel / perimeter C-Channel 25x50x25x0.5mm thick
4 Steel wire hanger @ 1000mm c/c
5 Board joints, all gaps sealed with intumescent sealant
6 9mm thick Wins H-Tec �re protection panel �llet, 100mm width
7 Self tapping screws at nominal 200mm centres
8 Rockwool-2 layers of 50mm thick (80KG/M³ )
9 Ceiling opening, sti�ener galvanised steel C-Channel 75x50x75x0.5mm thick
10 Access panel (optional, any board surface)
Legend :
H-TEC FIRE PROTECTION PANEL
Page 31
9mm THICK SUSPENDED CEILING SYSTEM WITH ACCESS PANEL1 hour Fire Rating, Integrity and Insulation in accordance with BS EN 1364-2:1999
1
7
56
2
2
84
3
10
ISOMETRIC VIEW60 min. CEILING SYSTEM
5
1 Wins H-Tec �re protection panel 9mm thick
2 Steel C-Channel at 610mm spacing 32x50x32x0.5mm thick
3 Furring channel / perimeter C-Channel 25x50x25x0.5mm thick
4 Steel wire hanger@1000mm c/c
5 Board joints, all gaps sealed with intumescent sealant
6 Wins H-Tec �re protection panel �llet 100mm width 9mm thick
7 Self tapping screws at nominal 200mm centres
8 Rockwool-2 layers of 50mm thk (80KG/M³ )
Legend :
H-TEC FIRE PROTECTION PANEL
Page 32
9mm THICK SUSPENDED CEILING SYSTEM WITH ACCESS PANEL1 hour Fire Rating, Integrity and Insulation in accordance with BS EN 1364-2:1999
6 7 1 6 2 5 47
3 3
8
HORIZONTAL SECTION60 min. CEILING SYSTEM
1 Wins H-Tec �re protection panel 9mm thick
2 Steel C-Channel at 610mm spacing 32x50x32x0.5mm thick
3 Furring channel / perimeter C-Channel 25x50x25x0.5mm thick
4 Steel wire hanger @ 1000mm c/c
5 Board joints -all gaps sealed by intumescent sealant
6 Wins H-Tec �re protection panel �llet 100mm width 9mm thick
7 Self tapping screws at nominal 200mm centres
8 Rockwool-2 layers of 50mm thk (80KG/M³ )
9 Ceiling opening, sti�ener galvanised steel C-Channel 75x50x75x0.5mm thick
10 Access panel (optional, any board surface)
Legend :
H-TEC FIRE PROTECTION PANEL
Page 33
9mm THICK SUSPENDED CEILING SYSTEM WITH ACCESS PANEL1 hour Fire Rating, Integrity and Insulation in accordance with BS EN 1364-2:1999
WINS ACCESS PANEL
CLOSE
OPEN
9
6 6
7
3
8
10
1
3
1
1 wins H-Tec �re protection panel 9mm thick
2 steel C-channel at 610mm spacing 50 x 32 x 0.5mm thick
3 furring channel / perimeter channel 50 x 25 x 0.5mm thick
4 steel wire hanger @ 1000mm c/c
5 Board joints -all gaps sealed by intumescent sealant
6 Wins H-tec �re protection �llet 100mm width 9mm thick
7 Self tapping screws at nominal 200mm centres
8 Rockwool,2 layers of 50mm thick,density 80kg/m³
Legend :
H-TEC FIRE PROTECTION PANEL4 HOURS FIRE RESISTANCE CEILING SYSTEM
Page 34
9mm WINS H-Tec Fire Protection Panel4 hours �re resistance, integrity and insulation in accordance with BS EN 1364-2:1999
1
7
25
6
4
83
1 Wins H-tec �re protection panel 12mm thick
2 Steel C-channel at 610mm spacing 50 x 32 x 0.5mm thick
3 Furring channel / perimeter channel 50 x 25 x 0.5mm thick
4 Steel wire hanger @ 1000mm c/c
5 Board joints -all gaps sealed by intumescent sealant
6 Wins h-tec �re protection �llet 100mm width 9mm thick
7 Self tapping screws at nominal 200mm centres
8 Rockwool,2 layers of 50mm thick, density 80kg/m³
Legend :
H-TEC FIRE PROTECTION PANEL4 HOURS FIRE RESISTANCE CEILING SYSTEM
Page 35
12mm WINS H-Tec Fire Protection Panel4 hours �re resistance, integrity and insulation in accordance with BS EN 1364-2:1999
1
7
25
6
4
83
H-TEC FIRE PROTECTION PANEL4 HOURS FIRE RESISTANCE CEILING SYSTEM
Page 36
9mm WINS H-Tec Fire Protection Panel4 hours �re resistance, integrity in accordance with BS EN 1364-2:1999
1 Wins H-Tec Fire Protection Panel 9mm Thick
2 Steel C-channel At 610mm Spacing 50 X 32 X 0.5mm Thick
3 Furring Channel / Perimeter Channel 50 X 25 X 0.5mm Thick
4 Steel Wire Hanger @ 1000mm C/C
5 Board Joints -All Gaps Sealed By Intumescent Sealant
6 Wins H-Tec Fire Protection Fillet, 100mm Width 9mm Thick
7 Self Tapping Screws At Nominal 200mm Centres
1 Wins H-tec �re protection panel 9mm thick
2 Steel C-channel at 610mm spacing 50x32x0.5mm thick
3 Furring channel/perimeter c-channel 50x25x0.5mm thick
4 Steel wire hanger @1000mm c/c
5 Board joints – all gaps sealed by intumescent sealant
6 Wins h-tec �re protection �llet, 100mm width 9mm thick
7 Self tapping screws at nominal 200mm centres
4
6
3
7
21 5
1
7
25
6
4
3
Page 37
1 Wins H-Tec Fire Protection Panel, 9mm thick
2 Wins H-Tec Fire Protection Fillets 100mm wide x 9mm thick
3 Top steel channel, 24mmx50mmx24mmx1mm thick
4 Horizontal steel stud, 32mmx50mmx32mmx0.5mm thick
5 Bottom steel channel, 24mmx50mmx24mmx0.5mm thick
6 M8 anchor bolt, @610mm c/c
7 M4x25mm self-tapping screw, @200mm c/c
8 Furnace wall
9 30mm free edge
Board Joints with �re retardant sealant
Vertical steel stud, 32mmx50mmx32mmx0.5mm thick, @610mm c/c
Legend :
10
11
7
Detail A
Detail B
Detail C
5
2
1
1
4
3
6
Detail A Detail B Detail C
WINS H-TEC FIRE PROTECTION PANEL9mm WINS H-TEC Smoke Barrier System
2 hours �re rating, integrity in accordance with BS 476: Part 22: 1987
WINS H-TEC FIRE PROTECTION PANEL9mm WINS H-TEC Smoke Barrier System
2 hours �re rating, integrity in accordance with BS 476: Part 22: 1987
Page 38
1 Wins H-Tec Fire Protection Panel, 9mm thick
2 Wins H-Tec Fire Protection Fillets 100mm wide x 9mm thick
3 Top steel channel, 24mmx50mmx24mmx1mm thick
4 Horizontal steel stud, 32mmx50mmx32mmx0.5mm thick
5 Bottom steel channel, 24mmx50mmx24mmx0.5mm thick
6 M8 anchor bolt, @610mm c/c
7 M4x25mm self-tapping screw, @200mm c/c
8 Furnace wall
9 30mm free edge
Board Joints with �re retardant sealant
Vertical steel stud, 32mmx50mmx32mmx0.5mm thick, @610mm c/c
Legend :
10
11
5
4
3
10
7
1
2
11
2
1
2
Website : www.winsconsultants.com