Post on 01-Sep-2018
Klippon® TB QL - Quarter Lock
Klippon® TB QL - Quarter Lock
Steel enclosures for use in industrial and in explosive hazard areas
The Klippon® TB enclosure range features excellent performance characteristics, even under the most difficult environmental conditions, and comply with the stricter requirements of explosive hazard areas found in the process or power generation industries. The Klippon® TB QL enclosure range offers further improvements to a product line that is already successfully leading the market.
Weidmüller can manufacture and supply this enclosure to match customer specifications and fitted with all necessary terminals and cable glands.
T " \
Overview of enclosures
Ordering dataDescription Length x width x depth 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
in mm (below) (above + below) (below + sides) (all sides)KTB QL 221513 S4E_* 229 x 152 x 133 1199860000 1199870000 1199880000 1199890000KTB QL 262615 S4E_* 260 x 260 x 150 1199910000 1199920000 1199930000 1199940000KTB QL 262620 S4E_* 260 x 260 x 200 1199960000 1199970000 1199980000 1199990000KTB QL 303015 S4E_* 306 x 306 x 150 1200020000 1200030000 1200040000 1200050000KTB QL 303020 S4E_* 306 x 306 x 200 1200070000 1200080000 1200090000 1200100000KTB QL 352615 S4E_* 350 x 260 x 150 1200120000 1200130000 1200140000 1200150000KTB QL 352620 S4E_* 350 x 260 x 200 1200170000 1200180000 1200190000 1200210000KTB QL 403015 S4E_* 400 x 300 x 150 1200230000 1200240000 1200250000 1200260000KTB QL 403020 S4E_* 400 x 300 x 200 1200280000 1200290000 1200310000 1200320000KTB QL 453815 S4E_* 458 x 382 x 150 1200340000 1200350000 1200360000 1200370000KTB QL 453820 S4E_* 458 x 382 x 200 1200390000 1200410000 1200420000 1200430000KTB QL 484815 S4E_* 480 x 480 x 150 1200450000 1200460000 1200470000 1200480000KTB QL 484820 S4E_* 480 x 480 x 200 1200510000 1200520000 1200530000 1200540000KTB QL 553515 S4E_* 550 x 350 x 150 1200560000 1200570000 1200580000 1200590000KTB QL 553520 S4E_* 550 x 350 x 200 1200620000 1200630000 1200640000 1200650000KTB QL 624515 S4E_* 620 x 450 x 150 1200670000 1200680000 1200690000 1200710000KTB QL 624520 S4E_* 620 x 450 x 200 1200730000 1200740000 1200750000 1200760000KTB QL 765015 S4E_* 762 x 508 x 150 1200780000 1200790000 1200810000 1200820000KTB QL 765020 S4E_* 762 x 508 x 200 1200840000 1200850000 1200860000 1200870000KTB QL 916115 S4E_* 914 x 610 x 150 1200890000 1200910000 1200920000 1200930000KTB QL 916120 S4E_* 914 x 610 x 200 1200950000 1200960000 1200970000 1200980000KTB QL 987420 S4E_* 980 x 740 x 200 1201010000 1201020000 1201030000 1201040000Note * Placeholder for the number of gland plates (1, 2, 3, 4). Klippon® TB QL enclosures are available without gland plates on request.
B.38
B
Enclo
sure
s
1420920000 – 2013/2014
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Klippon® TB QL - Quarter Lock
Technical OverviewFeatures
• Available in 12 sizes and 3 standard depths• Equipped with up to 4 gland plates• The gasket is protected against compression• Quick-locking lid, comes with a slot as standard• Improved temperature performance• IP66 protection class• Earth studs in enclosure cover and bottom section• Welded mounting feetNote
Technical data
Enclosure material** Stainless steel 1.4404 (316L) 1.5 mmSurface finish ElectropolishedIP protection class IP 66 to IEC EN 60079-0NEMA protection classes 3, 4x, 12Gland plates 1 - 4 (fixed with M6 hexagon head screws and 10 mm heads), optionally without a gland plateGland plate thickness 3 mm (other thickness of up to 20 mm are available on request) Earthing inside Enclosure base and lid: welded M6 stainless steel earth studsEarthing outside Continuous M10 brass earth stud (optionally with stainless-steel earth stud)Installation mounting 4 or 9 mounting bolts with M6 threaded holes to attach the mounting plate or mounting railsEnclosure attachment 4 welded mounting feet with 11-mm holes (2 slotted and 2 cross-shaped openings)Lid opening Can be removed completely, lid opening angle 130 °Cover attachment Quarter-turn lock with slotted insert (other inserts available on request)Impact resistance 7 J ATEX applications, 10 J industrial applicationsGasket material SiliconeOperating temperature range -60 °C...+135 °CLid screws, torque* 2.5 NmNote * For screwing on the cover, we recommend our hexagon 10 mm socket wrench (9009070000)
** Painted steel enclosures are available on request.
Approvals for empty enclosures
ATEX certificate KEMA 10ATEX0047 UATEX marking II 2 G Ex e llC Gb
II 2 D Ex tb lllC Db IP66IECEx certificate IECEx KEM 10.0016UIECEx marking Ex e IIC Gb
Ex tb IIIC Db IP66GOST Ex POCC DE.ME92.B02036cULus E243298Germanischer Lloyd 11534 - 10 HHRussian Maritime Register 10.04095.250INMETRO In preparationNote The Klippon® TB QL enclosure range can be pre-fitted in our customer specific production department according to your wishes;
as an example, terminals, or other approved components, can be installed as required.
Approvals for control and distribution box
ATEX certificate KEMA 10ATEX0051ATEX marking II 2 G Ex eb IIC T6...T4
II 1 G Ex ia IIC T6...T4II 2(1) G Ex eb ia IIC T6...T4II 2 D Ex tb lllC T85 °C...T135 °C IP66
IECEx certificate IECEx KEM 10.0020IECEx marking Ex eb IIC T...
Ex ia IIC T...Ex eb ia IIC T...Ex tb IIIC T85 °C…T135 °C IP66
Note Labelling depends on the application layout.
B.39
B
Enclo
sure
s
1420920000 – 2013/2014
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Integrate, expand and customise: the perfect supplement to every application
The fully structured range of system accessories for the Klippon® TB enclosure range allows you to easily adapt the enclosure to meet the specific requirements of every application.
The following options are available:
Klippon® TB QL - Quarter Lock
1
23
4
5
6
7
8
6
9
1 Document holder
Document holders for storage of important documents in the enclosure.
2 Earthing studs
Earthing studs are replaceable. Available in two versions – brass and stainless steel.
3 Gland plates
Gland plates are available as spares and also in various material thicknesses.
4 Mounting plates
Mounting plates with and without a drilling pattern, for horizontal and vertical mounting of rails, or components fitted directly.
5 Mounting hardware kits
Mounting hardware kits are available for quick and easy installation of label holders, mounting plates, gland plates, document holders and rain hoods.
6 Door stay
A door stay prevent the door from being closed unintentionally, regardless of the mounting position of the enclosure. This item is only available Ex-works.
7 Locking systems
Various locking systems are available for the safe securing of the enclosure. There are padlocks for the Klippon® TB MH enclosures and a range of lock inserts for the Klippon® TB QL enclosures.
8 Type label holder
A range of label holders are available for product identification.
9 Rain hoods
The rain hood provides an ideal, additional level of protection for the enclosure. Particularly useful against heavy rainfall or extreme levels of direct sunlight.
B.40
B
Enclo
sure
s
1420920000 – 2013/2014
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.411420920000 – 2013/2014
Klippon® TB QL 221513 Depth 133 mm
Height/Width/Depth 229 / 152 / 133 mm
10064
Ø 11
55.5
177
147
116146
178/208*152
A
152
229
15
13311
0
F
B
EC D
55 158
176
9375
15
64 100
M10 internal/external ground connection
M6 internal ground connection
View without cover, seal and lock
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 11998600002 gland plates - top and bottom sides (A & B) 1199870000
3 gland plates - bottom, left and right sides (B, C & D) 11998800004 gland plates - top, bottom, left and right sides (A, B, C & D) 1199890000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 1x29 1x154 mm² 1x136 mm² 1x9
10 mm² 1x716 mm² 1x635 mm²
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939300001193810000125765000006426000001274150000
0935110000093512000009351300000935140000
125627000012562800001253230000
1281360000
127932000012834500001257640000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 6 8M16 5 6M20 2 3M25 2 2M32 1 2M40 1 2M50 0 0M63 0 0M75 0 0
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
91.00
75.00
158.00
174.00
Ø 7
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.42 1420920000 – 2013/2014
Klippon® TB QL 262615 Depth 150 mm
Height/Width/Depth 260 / 260 / 150 mm
201183
Ø 11
55.5
189
207
286 / 316*260
A
170
260
15
150
127
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
224254
81 117
15
208
178
11781
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 11999100002 gland plates - top and bottom sides (A & B) 1199920000
3 gland plates - bottom, left and right sides (B, C & D) 11999300004 gland plates - top, bottom, left and right sides (A, B, C & D) 1199940000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x35 2x344 mm² 1x30 1x296 mm² 1x22 1x22
10 mm² 1x18 1x1716 mm² 1x15 1x1435 mm²
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939500001193820000125766000006426000001274150000
0935110000093512000009351300000935140000
125629000012563100001253230000
1281370000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 20 15M16 11 8M20 9 7M25 4 3M32 3 2M40 3 2M50 2 2M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
199.00
183.00
189.00
Ø 7
205.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.431420920000 – 2013/2014
Klippon® TB QL 262620 Depth 200 mm
Height/Width/Depth 260 / 260 / 200 mm
201183
Ø 11
55.5
189
207
214250
286 / 316*260
A
170
260
15
B
C D
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection
131
167
177
200
204
168
167131
126.5
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 11999600002 gland plates - top and bottom sides (A & B) 1199970000
3 gland plates - bottom, left and right sides (B, C & D) 11999800004 gland plates - top, bottom, left and right sides (A, B, C & D) 1199990000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x35 2x344 mm² 1x30 1x296 mm² 1x22 1x22
10 mm² 1x18 1x1716 mm² 1x15 1x1435 mm²
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939500001193820000125766000006426000001274150000
0935110000093512000009351300000935140000
125632000012563300001253230000
1281380000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 33 25M16 22 16M20 14 11M25 12 9M32 6 4M40 5 4M50 2 2M63 2 1M75 1 1
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
199.00
183.00
189.00
Ø 7
205.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.44 1420920000 – 2013/2014
Klippon® TB QL 303015 Depth 150 mm
Height/Width/Depth 306 / 306 / 150 mm
247229
Ø 11
55.5
332 / 362*306
A
203
306
15
15012
7
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection270
300
81 117
15
254
224
235
253
11781
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12000200002 gland plates - top and bottom sides (A & B) 1200030000
3 gland plates - bottom, left and right sides (B, C & D) 12000400004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200050000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x44 2x434 mm² 2x37 2x366 mm² 2x28 2x27
10 mm² 1x22 1x2216 mm² 1x19 1x1835 mm² 1x14 1x13
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939600001193830000125767000006426000001274150000
0935110000093512000009351300000935140000
125634000012563500001253230000
1281390000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 24 20M16 13 11M20 11 9M25 5 4M32 4 3M40 3 3M50 3 2M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
245.00
229.00
235.00
Ø 7
251.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.451420920000 – 2013/2014
Klippon® TB QL 303020 Depth 200 mm
Height/Width/Depth 306 / 306 / 200 mm
247229
Ø 11
55.5
260296
332 / 362*306
A
203
306
15
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
131
167
177
200
235
253
167131
126.5
250
214
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12000700002 gland plates - top and bottom sides (A & B) 1200080000
3 gland plates - bottom, left and right sides (B, C & D) 12000900004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200100000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x44 2x434 mm² 2x37 2x366 mm² 2x28 2x27
10 mm² 1x22 1x2216 mm² 1x19 1x1835 mm² 1x14 1x13
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939600001193830000125767000006426000001274150000
0935110000093512000009351300000935140000
125636000012563700001253230000
1281400000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 40 33M16 26 22M20 17 14M25 14 12M32 8 6M40 6 5M50 3 2M63 2 2M75 2 1
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
245.00
229.00
235.00
Ø 7
251.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.46 1420920000 – 2013/2014
Klippon® TB QL 352615 Depth 150 mm
Height/Width/Depth 350 / 260 / 150 mm
201183
Ø 11
55.5
286 / 316*260
A
279
297
150127
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
81 117
15
298
268
11781
224254
15
149
250
350
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12001200002 gland plates - top and bottom sides (A & B) 1200130000
3 gland plates - bottom, left and right sides (B, C & D) 12001400004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200150000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x53 2x344 mm² 1x44 2x296 mm² 1x33 2x22
10 mm² 1x27 2x1716 mm² 1x22 1x1435 mm² 1x11
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939700001193840000125768000006426000001274150000
0935110000093512000009351300000935140000
125638000012563900001253230000
1281410000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 20 23M16 11 13M20 9 11M25 4 5M32 3 4M40 3 3M50 2 3M63 0 0M75 0 0
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
199.00
183.00
279.00
295.00
Ø 7
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.471420920000 – 2013/2014
Klippon® TB QL 352620 Depth 200 mm
Height/Width/Depth 350 / 260 / 200 mm
201183
Ø 11
55.5
214250
286 / 316*260
A
279
297
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
131
167
177
200
167131
126.5
294
258
15
149
250
350
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12001700002 gland plates - top and bottom sides (A & B) 1200180000
3 gland plates - bottom, left and right sides (B, C & D) 12001900004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200210000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x53 2x344 mm² 1x44 2x296 mm² 1x33 2x22
10 mm² 1x27 2x1716 mm² 1x22 1x1435 mm² 1x11
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939700001193840000125768000006426000001274150000
0935110000093512000009351300000935140000
125641000012564200001253230000
1281420000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 33 38M16 22 26M20 14 17M25 12 14M32 6 7M40 5 6M50 2 3M63 2 2M75 1 2
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
199.00
183.00
279.00
295.00
Ø 7
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.48 1420920000 – 2013/2014
Klippon® TB QL 403015 Depth 150 mm
Height/Width/Depth 400 / 300 / 150 mm
Ø 11
55.5
326 / 356*300
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
81 117
15
348
318
11781
264294
199
247
400
241223
329
347
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12002300002 gland plates - top and bottom sides (A & B) 1200240000
3 gland plates - bottom, left and right sides (B, C & D) 12002500004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200260000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x62 3x424 mm² 2x52 3x356 mm² 1x39 2x26
10 mm² 1x32 2x2116 mm² 1x26 2x1835 mm² 1x20 1x13
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939800001193850000125769000006426000001274150000
0935110000093512000009351300000935140000
125643000012564400001253230000
1281430000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 23 29M16 13 16M20 11 13M25 5 6M32 4 5M40 3 4M50 3 3M63 0 0M75 0 0
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
239.00
223.00
329.00
345.00
Ø 7
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.491420920000 – 2013/2014
Klippon® TB QL 403020 Depth 200 mm
Height/Width/Depth 400 / 300 / 200 mm
Ø 11
55.5
254290
326 / 356*300
A
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection13
116
7
167131
126.5
344
308
199
247
400
241223
329
347
177
200
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12002800002 gland plates - top and bottom sides (A & B) 1200290000
3 gland plates - bottom, left and right sides (B, C & D) 12003100004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200320000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x62 3x424 mm² 2x52 3x356 mm² 1x39 2x26
10 mm² 1x32 2x2116 mm² 1x26 2x1835 mm² 1x20 1x13
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939800001193850000125769000006426000001274150000
0935110000093512000009351300000935140000
125645000012564700001253230000
1281440000
127932000012834500001257640000
1252780000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 38 48M16 26 32M20 17 20M25 14 17M32 7 9M40 6 7M50 3 3M63 2 3M75 2 2
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
239.00
223.00
329.00
345.00
Ø 7
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.50 1420920000 – 2013/2014
Klippon® TB QL 453815 Depth 150 mm
Height/Width/Depth 458 / 382 / 150 mm
Ø 11
55.5
408 / 438*382
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection81 11
7
15
406
376
11781
346376
157
305
458
323305
387
405
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12003400002 gland plates - top and bottom sides (A & B) 1200350000
3 gland plates - bottom, left and right sides (B, C & D) 12003600004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200370000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 3x73 4x584 mm² 2x62 3x486 mm² 2x46 3x36
10 mm² 2x37 2x2916 mm² 2x31 2x2435 mm² 1x23 1x18
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939900001193860000125770000006426000001274150000
0935110000093512000009351300000935140000
125648000012564900001253230000
1281450000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 30 33M16 17 19M20 15 16M25 6 7M32 5 6M40 4 5M50 4 4M63 0 0M75 0 0
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
321.00
305.00
387.00
403.00
Ø 7
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.511420920000 – 2013/2014
Klippon® TB QL 453820 Depth 200 mm
Height/Width/Depth 458 / 382 / 200 mm
Ø 11
55.5
336372
408 / 438*382
A
B
C D
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection13
116
7
167131
126.5
402
366
157
305
458
323305
387
405
177
200
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12003900002 gland plates - top and bottom sides (A & B) 1200410000
3 gland plates - bottom, left and right sides (B, C & D) 12004200004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200430000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 3x73 4x584 mm² 2x62 3x486 mm² 2x46 3x36
10 mm² 2x37 2x2916 mm² 2x31 2x2435 mm² 1x23 1x18
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11939900001193860000125770000006426000001274150000
0935110000093512000009351300000935140000
125651000012565200001253230000
1281460000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 50 55M16 34 38M20 23 24M25 18 21M32 10 11M40 8 9M50 4 4M63 3 3M75 2 3
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
321.00
305.00
387.00
403.00
Ø 7
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.52 1420920000 – 2013/2014
Klippon® TB QL 484815 Depth 150 mm
Height/Width/Depth 480 / 480 / 150 mm
Ø 11
55.5
506 / 536*480
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection
81 117
15
428
398
11781
444474
179
327
480
421403
409
427
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12004500002 gland plates - top and bottom sides (A & B) 1200460000
3 gland plates - bottom, left and right sides (B, C & D) 12004700004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200480000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 4x78 4x774 mm² 3x65 3x646 mm² 3x49 3x48
10 mm² 2x39 3x3916 mm² 2x33 2x3235 mm² 1x25 2x24
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940000001193870000125771000006426000001274150000
0935110000093512000009351300000935140000
125653000012565400001253230000
1281470000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 39 36M16 22 20M20 19 17M25 8 7M32 7 6M40 6 5M50 5 4M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
419.00
403.00
409.00
Ø 7
425.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.531420920000 – 2013/2014
Klippon® TB QL 484820 Depth 200 mm
Height/Width/Depth 480 / 480 / 200 mm
Ø 11
55.5
434470
506 / 536*480
A
B
C D
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection
131
167
167131
126.5
424
388
179
327
480
421403
409
427
177
200
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12005100002 gland plates - top and bottom sides (A & B) 1200520000
3 gland plates - bottom, left and right sides (B, C & D) 12005300004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200540000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 4x78 4x774 mm² 3x65 3x646 mm² 3x49 3x48
10 mm² 2x39 3x3916 mm² 2x33 2x3235 mm² 1x25 2x24
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940000001193870000125771000006426000001274150000
0935110000093512000009351300000935140000
125655000012565600001253230000
1281480000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 65 60M16 44 40M20 29 26M25 24 21M32 13 12M40 11 10M50 5 4M63 4 4M75 3 3
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
419.00
403.00
409.00
Ø 7
425.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.54 1420920000 – 2013/2014
Klippon® TB QL 553515 Depth 150 mm
Height/Width/Depth 550 / 350 / 150 mm
Ø 11
55.5
314344
376 / 406350
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection81 11
7
15
498
468
11781
249
350
550
291273
479
497
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12005600002 gland plates - top and bottom sides (A & B) 1200570000
3 gland plates - bottom, left and right sides (B, C & D) 12005800004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200590000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x91 4x524 mm² 2x76 4x436 mm² 2x58 4x32
10 mm² 2x46 3x2616 mm² 1x39 3x2235 mm² 1x29 2x16
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940100001193880000125772000006426000001274150000
0935110000093512000009351300000935140000
125657000012565800001253230000
1281490000
127932000012834500001257640000
12527800001252750000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 27 42M16 15 24M20 13 20M25 6 9M32 5 7M40 4 6M50 3 5M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
289.00
273.00
Ø 7
479.00
495.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.551420920000 – 2013/2014
Klippon® TB QL 553520 Depth 200 mm
Height/Width/Depth 550 / 350 / 200 mm
Ø 11
55.5
376 / 406350
A
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
131
167
167131
126.5
494
458
249
350
550
291273
479
497
177
200
15
304340
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12006200002 gland plates - top and bottom sides (A & B) 1200630000
3 gland plates - bottom, left and right sides (B, C & D) 12006400004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200650000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 2x91 4x524 mm² 2x76 4x436 mm² 2x58 4x32
10 mm² 2x46 3x2616 mm² 1x39 3x2235 mm² 1x29 2x16
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940100001193880000125772000006426000001274150000
0935110000093512000009351300000935140000
125659000012566100001253230000
1281500000
127932000012834500001257640000
12527800001252750000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 45 70M16 30 48M20 20 30M25 17 26M32 9 14M40 7 12M50 3 5M63 3 4M75 2 3
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
289.00
273.00
Ø 7
479.00
495.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.56 1420920000 – 2013/2014
Klippon® TB QL 624515 Depth 150 mm
Height/Width/Depth 620 / 450 / 150 mm
Ø 11
55.5
414444
476 / 506*450
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection81 11
7
15
568
538
11781
319
450
620
391359
535
567
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12006700002 gland plates - top and bottom sides (A & B) 1200680000
3 gland plates - bottom, left and right sides (B, C & D) 12006900004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200710000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 3x105 5x714 mm² 3x88 5x596 mm² 3x66 4x45
10 mm² 2x53 4x3616 mm² 2x44 3x3035 mm² 1x33 2x22
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940200001193890000125774000006426000001274150000
0935110000093512000009351300000935140000
125662000012566300001253230000
1281510000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 38 48M16 21 27M20 18 24M25 8 10M32 6 9M40 5 7M50 4 6M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
389.00
359.00
Ø 7
535.00
565.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.571420920000 – 2013/2014
Klippon® TB QL 624520 Depth 200 mm
Height/Width/Depth 620 / 450 / 200 mm
Ø 11
55.5
476 / 506*450
A
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection13
116
7
167131
126.5
564
528
319
450
620
391359
535
567
177
200
404440
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12007300002 gland plates - top and bottom sides (A & B) 1200740000
3 gland plates - bottom, left and right sides (B, C & D) 12007500004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200760000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 3x105 5x714 mm² 3x88 5x596 mm² 3x66 4x45
10 mm² 2x53 4x3616 mm² 2x44 3x3035 mm² 1x33 2x22
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940200001193890000125774000006426000001274150000
0935110000093512000009351300000935140000
125664000012566500001253230000
1281520000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 63 80M16 42 54M20 27 36M25 23 30M32 12 17M40 10 14M50 4 6M63 4 5M75 3 4
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
389.00
359.00
Ø 7
535.00
565.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.58 1420920000 – 2013/2014
Klippon® TB QL 765015 Depth 150 mm
Height/Width/Depth 762 / 508 / 150 mm
Ø 11
55.5
472502
534 / 564*508
A
F
B
EC D
64
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
81 117
15
345
315
11781
461
508
762
449417
677
709
127
150
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12007800002 gland plates - top and bottom sides (A & B) 1200790000
3 gland plates - bottom, left and right sides (B, C & D) 12008100004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200820000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 4x132 7x824 mm² 4x111 6x696 mm² 3x83 5x52
10 mm² 3x67 5x4216 mm² 2x56 4x3535 mm² 2x42 3x26
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940300001193900000125775000006426000001274150000
0935110000093512000009351300000935140000
125666000012566700001253230000
1281530000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 42 58M16 24 32M20 21 26M25 9 12M32 7 10M40 6 8M50 5 6M63 0 0M75 0 0
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
447.00
417.00
Ø 7
677.00
707.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.591420920000 – 2013/2014
Klippon® TB QL 765020 Depth 200 mm
Height/Width/Depth 762 / 508 / 200 mm
Ø 11
55.5
534 / 564*508
A
B
C D
View without cover,seal and lock
M10 internal/externalground connection
M6 internal ground connection
131
167
167131
126.5
341
305
461
508
762
449417
677
709
177
200
462498
15
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12008400002 gland plates - top and bottom sides (A & B) 1200850000
3 gland plates - bottom, left and right sides (B, C & D) 12008600004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200870000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 4x132 7x824 mm² 4x111 6x696 mm² 3x83 5x52
10 mm² 3x67 5x4216 mm² 2x56 4x3535 mm² 2x42 3x26
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940300001193900000125775000006426000001274150000
0935110000093512000009351300000935140000
125668000012566900001253230000
1281540000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 70 96M16 48 64M20 32 40M25 26 34M32 14 18M40 12 14M50 5 6M63 4 6M75 3 4
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
447.00
417.00
Ø 7
677.00
707.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.60 1420920000 – 2013/2014
Klippon® TB QL 916115 Depth 150 mm
Height/Width/Depth 914 / 610 / 150 mm
Ø 11
55.5
574604
636 / 666*610
A
64
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection
81 117
15
11781
559
613
914
551519
829
861
127
150
15
421
391
FE
B
C D
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12008900002 gland plates - top and bottom sides (A & B) 1200910000
3 gland plates - bottom, left and right sides (B, C & D) 12009200004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200930000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 5x161 8x1024 mm² 4x135 7x856 mm² 4x102 7x64
10 mm² 3x82 6x5216 mm² 3x68 5x4335 mm² 2x51 4x32
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940400001193910000125776000006426000001274150000
0935110000093512000009351300000935140000
125671000012567200001253230000
1281550000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 53 70M16 29 40M20 25 34M25 11 14M32 9 12M40 8 10M50 6 8M63 0 0M75 0 0
Note Our IP 68 brass cable glands are used as the reference for these guideline values.
Dimensions of mounting plate
549.00
519.00
Ø 7
829.00
859.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.611420920000 – 2013/2014
Klippon® TB QL 916120 Depth 200 mm
Height/Width/Depth 914 / 610 / 200 mm
Ø 11
55.5
636 / 666*610
A
View without cover,seal and lock
M10 internal/externalground connectionM6 internal ground connection
131
167
167131
126.5
417
381
559
613
914
551519
829
861
177
200
564600
15
B
C D
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12009500002 gland plates - top and bottom sides (A & B) 1200960000
3 gland plates - bottom, left and right sides (B, C & D) 12009700004 gland plates - top, bottom, left and right sides (A, B, C & D) 1200980000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 5x161 8x1024 mm² 4x135 7x856 mm² 4x102 7x64
10 mm² 3x82 6x5216 mm² 3x68 5x4335 mm² 2x51 4x32
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940400001193910000125776000006426000001274150000
0935110000093512000009351300000935140000
125673000012567400001253230000
1281570000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 88 116M16 58 80M20 38 52M25 33 42M32 18 24M40 15 20M50 6 8M63 5 6M75 4 6
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
549.00
519.00
Ø 7
829.00
859.00
Enclo
sure
s
Klippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
B
B.62 1420920000 – 2013/2014
Klippon® TB QL 987420 Depth 200 mm
Height/Width/Depth 980 / 740 / 200 mm
Ø 11
55.5
766 / 796*740
A
131
167
15
167131
126.5
625
679
980
681650
896
927
177
200
317353
15
450
414
FE
B
C D
M10 internal/external ground connection
M6 internal ground connection
View without cover, seal and lock
Ordering dataStainless steel 1.4404 316L, electropolished Order No.
1 gland plate - bottom 12010100002 gland plates - top and bottom sides (A & B) 1201020000
3 gland plates - bottom, left and right sides (B, C & D) 12010300004 gland plates - top, bottom, left and right sides (A, B, C & D) 1201040000
Note Painted sheet steel enclosure available on request. Standard colour is similar to RAL 7035.
Max. number of terminals (industry)Max. number of terminals (industry) vertical horizontal
2.5 mm² 6x174 9x1274 mm² 6x146 8x1066 mm² 5x110 7x80
10 mm² 4x88 6x6416 mm² 4x74 5x5435 mm² 3x55 4x40
Note *For enclosure versions with zero, one or two gland plates, the horizontal gap between the mounting feet is reduced by 30 mm. Assembly with terminal blocks provides for 10 mm clearance to the ends of the mounting rail. Recommended order: TS 35 mounting rail (screw terminal) WDU 2.5 1020000000 / (tension clamp terminal) ZDU 2.5 1608510000 / (tension clamp terminal) PDU 2.5 1896110000 TS 32 mounting rail (screw terminal) SAK 2.5 0279660000 TS 15 mounting rail (screw terminal) AKZ 2.5 0697160000
AccessoriesMounting plates and fastening screws
Steel sheet, zinc platedStainless steel 1.4301
With hole pattern, natural stainless steel 1.4301Fastening screws for mounting plates
Fastening screws for terminal railsStainless steel spacer M6 x 8, Set of 4
10 mm length15 mm length20 mm length30 mm length
Gland plates and screws - 6 mmTop and bottom sides (A & B), electropolished stainless steel 1.4404
Left and right sides (C & D), electropolished stainless steel 1.4404Mounting screw, stainless steel 1.4404
Mirror-polish Stainless steel 1.4301 rain hood (2R)
Label holder70 x 70 angled stainless steel 1.4301
130x50 stainless steel 1.4301100x25 stainless steel 1.4301
Document holderFor DIN A6 size documentsFor DIN A5 size documentsFor DIN A4 size documents
Set of fixingsFor label holders, rain hoods and document holders (rivet)
For plastic (Trafolyte), identification plate (screw)Earthing stud
Stainless steel 1.4404
Order No.11940500001193920000125777000006426000001274150000
0935110000093512000009351300000935140000
125675000012567600001253230000
1281580000
127932000012834500001257640000
125278000012527500001252730000
12521900001285200000
1192690000
Note
Number of cable entriesNumber of cable entries A / B C / D
M12 96 126M16 64 84M20 42 54M25 36 48M32 20 26M40 16 22M50 6 10M63 6 8M75 4 6
Note Our IP 68 brass cable glands serve as a reference for these recommended values.
Dimensions of mounting plate
680.00
650.00
Ø 7
896.00
926.00
Enclo
sure
sKlippon® TB QL - Quarter Lock
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com