Post on 20-Nov-2020
DRIVELINES E R V I C E S A U S T R A L I Athe underbody & power transmission specialists
Driveline Services Australia Pty Ltd (Driveline)is an underbody and power transmission parts andservices supplier specialising in the manufacture,export, import, supply and distribution of acomprehensive range of aftermarket underbody andpower transmission components. Driveline boastsan unsurpassed inventory of products and servicesfor tailshafts, drivetrains, differentials, gearboxes,suspension, power steering and constant velocityapplications.Established in Brisbane in 1982, Driveline has grownto incorporate a national network of nine branchesoffering workshop services for mining, light fleet,four wheel drive, passenger, performance, truck,bus, defence, agricultural, industrial and marinevehicles to the wholesale, trade and retail markets ofAustralia and the world.
DRIVELINE CATALOGUE SUITE
SPICER CATALOGUE PAGE:- 1
SPICER
September
2014 © Driveline Services Australia Pty Ltd
BEARING CAP TYPES
C
C
C
CC
1
5 7 8
2
2. 1. 3.
4.
LUBRICATION POINTS
FIG. 13
C
W1
C C
C
W1 W2 W2
FIG. 1 FIG. 2 FIG. 3
Back platescan be welded
or loose
UNIVERSAL JOINT DIMENSIONAL DATA.
DIA INT EXT CAPS C W1 W2 QTY TYPE FIG PART No. LUBE SERIES
19.05 52.00 4 1 2 K5A546 1 0500 SERIES SPICER
23.80 38.10 4 2 1 5.170X 1 1000 SERIES SPICER
23.80 38.10 4 2 1 5.170X.1A 3 1000 SERIES SPICER – Lube through 1 cap
23.80 61.20 4 1 2 K5LGB80R 1 1140 SERIES SPICER
23.80 61.20 4 1 2 K5LGB8OR.1A 3 1140 SERIES SPICER – Lube through 1 cap
26.99 61.93 4 1 2 5.443X 3 1210 SERIES SPICER
26.99 74.61 4 1 2 K5L4R 2 1300 SERIES SPICER
26.99 81.76 4 1 2 K5.13XR 2 1310 SERIES SPICER
26.99 81.76 4 1 2 5.433.1X 3 1310 SERIES SPICER – Lube through 1 cap
26.99 92.08 4 1 2 RUJ3002 2 1330 SERIES SPICER
30.16 92.08 4 1 2 5.178X 2 1350 SERIES SPICER
30.16 92.08 4 1 2 5.178X.1A 3 1350 SERIES SPICER – Lube through 1 cap
30.16 92.08 4 1 1 5.178XSP 2 1350 SERIES SPICER – Mark Williams Performance
30.16 106.35 4 1 2 K5GB10R 2 1410 SERIES SPICER
34.93 126.20 4 1 2 5.155X 2 1550 SERIES SPICER
34.93 106.38 4 1 2 5.188X 2 1480 SERIES SPICER
39.70 115.90 4 8 3 K5GB15R 2 1500 SERIES SPICER
39.70 115.90 4 1 2 K5GB22R 2 1510 SERIES SPICER
41.28 142.00 4 1 2 5.165X 2 1650 SERIES SPICER
47.63 134.94 4 5 3 5.279X 2 1610 SERIES SPICER
47.63 47.63
134.95 134.95
2 2
5 1
3
5.674X 2 1610 SERIES SPICER 1610 – HALF RND W/- STRAPS
SPICER CATALOGUE PAGE:- 2
SPICER
September
2014 © Driveline Services Australia Pty Ltd
BEARING CAP TYPES
C
C
C
CC
1
5 7 8
2
2. 1. 3.
4.
LUBRICATION POINTS
FIG. 13
C
W1
C C
C
W1 W2 W2
FIG. 1 FIG. 2 FIG. 3
Back platescan be welded
or loose
UNIVERSAL JOINT DIMENSIONAL DATA.
DIA INT EXT CAPS
C W1 W2 QTY TYPE FIG PART No. LUBE SERIES 49.21 154.78 4 5 3 5.280X 2 1710 SERIES SPICER
49.21 177.80 4 5 3 5.407X 2 1760 SERIES SPICER
49.21 191.75 4 5 3 5.281X 2 1810 SERIES SPICER
49.21 49.21
191.75 194.00
2 2
5 1
3 5.676X 2 1810 SERIES SPICER TO 1810 – HALF RND W/- STRAPS
55.00 164.00 4 1 2 SPL170X 1 SPL170
60.00 163.00 4 1 2 SPL250X 1 SPL250
52.33 174.75 2 2
1 CP20RPLS NON RPL20 MERITOR
52.33 208.28 2 2
1 CP25RPLS NON RPL25 MERITOR
SPICER CATALOGUE PAGE:- 3
SPICER
September
2014 © Driveline Services Australia Pty Ltd
PERFORMANCE COMPONENTS
AUTOMOTIVE SLIP YOKES
Spline C-EOS LTH Hub S L L1 O Part No. Application
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.375 x 16 3.50 2.25 1.89 3.3.39040 G-Force (34.9 x 16) (88.9) (57.2) (48.0)
1.375 x 16 4.00 3.50 1.89 3.3.39015 Lenco (34.9 x 16) (101.6) (89.0) (48.0)
1.375 x 16 4.00 2.75 1.89 3.3.39115 Lenco – Rapid Release (34.9 x 16) (101.6) (69.9) (48.0)
1.190 x 27 Inv 5.18 4.34 1.50 3.3.39005 Powerglide/Turbo 350 (30.2 x 27) (147.6) (110.3) (38.1)
1.196 x 28 Inv 6.14 5.12 1.50 3.3.39022 Ford C4 (30.4 x 28) (156.0) (130.0) (38.1)
1.312 x 30 Inv 6.30 5.43 1.68 3.3.39002 Liberty/Mopar/Doug Nash (33.3 x 30) (160.0) (138.0) (42.7)
1.397 x 31 Inv 6.30 5.43 1.68 3.3.39020 Ford C6/Toploader (35.2 x 31) (160.0) (138.0) (42.7)
1.397 x 32 Inv 5.90 5.00 1.89 3.3.39004 T400/Super T10 (35.5 x 32) (150.0) (127.0) (48.0)
1.375 x 32 Inv 4.00 3.23 1.89 3.3.39013 Lenco (34.9 x 32) (101.6) (82.0) (48.0)
SPICER CATALOGUE PAGE:- 4
SPICER
September
2014 © Driveline Services Australia Pty Ltd
PERFORMANCE COMPONENTS
WELD YOKES
Tube Butt C-W Size B L Part No. Notes / Suggestions
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
3.000 x .083 2.85 2.13 3.28.39017 Mark Williams Chrome Moly (76.2 x 2.11) (72.2) (54.0)
END YOKES
Spline Hub F-EOS DTH S O L L1 Part No. Notes / Suggestions
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.220 x 26 Inv 1.81 3.88 1.89 3.4.39908 Aluminum, Ford 9” (31.0 x 26) (46.0) (98.4) (48.0) Includes Hardened Splined Washer
1.220 x 28 Inv 1.81 3.88 1.89 3.4.39008 Pinion Yoke (31.0 x 28) (46.0) (98.4) (48.0) Mark Williams 9” Billet Diff Yoke
1.510 x 35 Inv 2.13 3.88 2.00 3.4.39011 Suit 9” Ford (38.4 x 35) (54.0) (98.4) (50.8)
1.510 x 35 Inv 2.13 3.88 2.00 3.4.39911 Aluminum, Ford 9” (38.4 x 35) (54.0) (98.4) (50.8) Includes Hardened Splined Washer
SPICER CATALOGUE PAGE:- 5
SPICER
September
2014 © Driveline Services Australia Pty Ltd
BORED & KEYED COMPANION FLANGES
Bore x Key OD Spigot PCD Holes Bolt Pattern DTH F-EOS Hub Notes / D4 x X N K D D1 D2 D3 L1 L O Part No. Suggestions
SERIES: 1140
0.500 x None 3.46 2.250 (F) 2.750 4x.31 1.77 2.13 1.50 2.12 2.00 1.1.PB (12.70 x -) (88.0) (57.1) (69.8) (4x8.0) (44.9) (54.0) (38.1) (54.0) (50.8)
SERIES: 1310 None None 3.82 2.375 3.125 4x.375 2.01 2.39 2.67 2.50 2.1.SB Solid Boss (97) (60.32) (79.35) (4x9.6) (51.1) (60.8) (68) (63.5)
0.750 x None 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.PB (19.05 x -) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
0.875 x .187 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.623 (22.20 x 4.75) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
1.000 x .250 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.283 (25.40 x 6.35) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
1.125 x .250 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.293 (28.58 x 6.35) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
1.125 x 0.312 3.82 2.375 3.125 4x.375 2.01 2.39 2.01 2.08 2.55 2.1.303 (28.58 x 7.95) (97) (60.32) (79.35) (4X9.6) (51.1) (60.8) (51) (53) (64.85)
1.250 x .312 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.333 (31.75 x 7.95) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
1.375 x .312 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 2.01 2.08 2.55 2.1.903 (34.93 x 7.95) (97.0) (60.3) (79.3) (4x9.6) (51.0) (60.8) (51.0) (53.0) (64.8)
SERIES: 1350 - 1410
None x None 4.53 2.750 (F) 3.750 4x.44 2.41 2.87 2.48 2.55 2.87 3.1.SB Solid Boss (- x -) (115.0) (69.8) (95.2) (4x11.1) (61.2) (72.9) (63.0) (65.0) (73.0)
0.750 x None 4.53 2.750 (F) 3.750 4x.44 2.41 2.87 2.48 2.55 2.87 3.1.PB (19.05 x -) (115.0) (69.8) (95.2) (4x11.1) (61.2) (72.9) (63.0) (65.0) (73.0)
1.250 x 0.312 4.53 2.750 (F) 3.750 4x.44 2.41 2.87 2.48 2.55 2.87 3.1.163 (31.75 x 7.95) (115.0) (69.8) (95.2) (4x11.1) (61.2) (72.9) (63.0) (65.0) (73.0)
1.50 x 0.375 4.56 2.750 3.750 4x0.437 2.41 2.87 2.48 2.55 2.87 3.1.333 (38.1 x 9.52) (116) (69.85) (95.27) (4x11.1) (61.2) (72.9) (63) (65) (73.0)
SERIES: 1480 - 1550
1.250 x None 5.75 3.750 (F) 4.750 4x.50 3.05 3.64 2.40 2.50 3.75 4.1.PB (31.75 x -) (146.0) (95.2) (120.6) (4x12.7) (77.5) (92.4) (61.0) (63.5) (95.2)
SPICER CATALOGUE PAGE:- 6
SPICER
September
2014 © Driveline Services Australia Pty Ltd
COMPANION FLANGES
Spline OD Spigot PCD Holes Bolt Pattern DTH F-EOS Hub Notes / S N K D D1 D2 D3 L1 L O Part No. Suggestions
SERIES: 1310
1.375 x 10 3.82 2.375 (F) 3.125 4x.37 2.01 2.39 1.44 2.39 - 2.1.2831 2.57.1441 (34.93 x 10) (97.0) (60.2) (79.3) (4x9.6) (51.0) (60.8) (36.6) (60.7)
1.375 x 10 4.96 1.77 (F) - - - - 1.44 2.19 - 2.1.2831SF Blank Face 2.57.1441 (34.93 x 10) (126.0) (45.0) (36.6) (55.6)
1.375 x 10 4.96 3.125 (M) 4.250 4x.44 3.00 3.00 1.44 2.19 - 2.1.7333 Saginaw 2.57.1441 (34.93 x 10) (126.0) (79.3) (107.9) (4x11.2) (76.3) (76.3) (36.6) (55.6) 4137268
SERIES: ISUZU (Mounting Face)
1.500 x 10 4.72 3.150 (F) 3.937 4x.40 2.00 3.18 2.00 2.69 - 3.1.014 3.57.2641 3.57.2651 (38.1 x 10) (120.0) (80.0) (100.0) (4x10.2) (50.8) (80.9) (50.8) (68.3)
1.750 x 10 5.83 3.150 (F) 4.331 4x.48 2.16 3.75 2.28 2.71 - 3.1.013 5.53.141 (44.45 x 10) (148.0) (80.0) (110.0) (4x12.2) (55.0) (95.3) (58.0) (69.0)
SERIES: MITSUBISHI (Mounting Face)
1.500 x 10 4.72 2.756 (F) 3.937 4x.48 2.53 3.01 2.00 2.69 - 3.1.352 3.57.2641 3.57.2651 (38.1 x 10) (120.0) (70.0) (100.0) (4x12.2) (64.3) (76.6) (50.8) (68.3)
SERIES: 1350 - 1410
1.000 x 15Inv 4.56 2.750 (F) 3.750 4x.44 2.41 2.87 1.77 2.32 - 3.1.04 Clamp lock Type (25.4 x 15) (116.0) (69.8) (95.2) (4x11.2) (61.2) (72.9) (45.0) (56.7) 1.375 x 6 4.56 2.750 (F) 3.750 4x0.437 2.41 2.87 1.77 2.32 - 3.1.33 Clamp lock Type (34.9 x 6) (116) (69.85) (95.27) (4x11.1) (61.2) (72.9) (45.0) (56.7)
1.375 x 21Inv 4.56 2.750 (F) 3.750 4x.44 2.41 2.87 1.77 2.32 - 3.1.07 Clamp lock Type (34.9 x 21) (116.0) (69.8) (95.2) (4x11.2) (61.2) (72.9) (45.0) (56.7)
1.417 x 8 4.56 2.750 (F) 3.750 4x.44 2.41 2.87 1.77 2.32 - 3.1.115 Clamp lock Type (36.0 x 8) (116.0) (69.8) (95.2) (4x11.2) (61.2) (72.9) (45.0) (56.7)
1.500 x 10 4.72 2.756 (F) 3.750 4x.44 2.41 2.87 2.00 2.69 3.1.352.1 MI.53.352 MI.53.352.1 (38.1 x 10) (120.0) (70.0) (95.2) (4x11.2) (61.2) (72.9) (50.8) (68.3) CB75
1.500 x 10 4.64 2.750 (F) 3.750 4x.44 2.41 2.87 2.00 2.69 - 3.1.6221 3.57.2641 3.57.2651 (38.1 x 10) (117.7) (69.8) (95.2) (4x11.2) (61.2) (72.9) (50.8) (68.3)
1.750 x 13Inv 4.56 2.750 (F) 3.750 4x0.437 2.41 2.87 1.77 2.32 - 3.1.13 Clamp lock Type (44.45 x 13) (116) (69.85) (95.27) (4x11.1) (61.2) (72.9) (45.0) (56.7)
1.922 x 14Inv 4.56 2.750 (F) 3.750 4x.44 2.41 2.87 2.18 2.32 2.36 3.1.0065 (48.8 x 14) (116.0) (69.8) (95.2) (4x11.2) (61.2) (72.9) (45.0) (56.7) (60.0)
NOTE: SOME COMPANION FLANGES MAY BE RECTANGULAR SHAPE
SPICER CATALOGUE PAGE:- 7
SPICER
September
2014 © Driveline Services Australia Pty Ltd
COMPANION FLANGES
Spline OD Spigot PCD Holes Bolt Pattern DTH F-EOS Hub Notes / S N K D D1 D2 D3 L1 L O Part No. Suggestions
SERIES: 1480 - 1550
1.500 x 10 5.750 3.750 (F) 4.750 4x.50 3.05 3.64 2.00 2.69 - K4.1.A2191 3.57.2641 3.57.2651 (38.1 x 10) (146.0) (95.2) (120.6) (4x12.7) (77.5) (92.4) (50.8) (68.3)
1.614 x 15 Inv 5.750 3.750 (F) 4.750 4x.50 3.05 3.64 1.97 3.35 2.12 4.1.0064 (38.1 x 15 Inv) (146.0) (95.2) (120.6) (4x12.7) (77.5) (92.4) (50.0) (85.0) (54.0)
1.750 x 10 5.750 3.750 (F) 4.750 4x.50 3.05 3.64 2.24 3.00 - K4.1.A0761 5.53.111 5.53.141 (44.45 x 10) (146.0) (95.2) (120.6) (4x12.7) (77.5) (92.4) (57.0) (76.2)
1.929 x 14 Inv 5.750 3.750 (F) 4.750 4x.50 3.05 3.64 2.18 3.35 2.36 4.1.0051 (49.0 x 14 Inv) (146.0) (95.2) (120.6) (4x12.7) (77.5) (92.4) (55.4) (85.0) (60.0)
SERIES: 1610
1.750 x 10 5.906 3.543 (F) 5.118 8x.48 - - 2.24 2.60 - 5.1.150812 DIN 150 Face 5.53.141 (44.45 x 10) (150.0) (90.0) (130.0) (8x12.2) (57.0) (66.0)
1.750 x 10 6.890 6.622 (F) 6.125 8x.37 - - 2.24 3.13 - K5.1.A0741 5.53.141 (44.45 x 10) (175.0) (168.2) (155.5) (8x9.6) (57.0) (79.6)
SERIES: 1810
2.344 x 16 8.000 7.750 (M) 7.250 12x.44 - - 2.75 3.44 - 6.5.1.1811 6.53.311 6.5.53.91 (59.5 x 16) (203.2) (196.8) (184.1) (12x11.2) (69.8) (87.3)
NOTE: SOME COMPANION FLANGES MAY BE RECTANGULAR SHAPE
SPICER CATALOGUE PAGE:- 8
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
O.D Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 0500 Suits U/J: K5A546 19.05 x 52.00
65.0 35.0 (F) 52.0 4x6.0 37.0 37.0 40.0 2 05.2.6546 DIN spec WHILE STOCKS LAST
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
4.311 2.205 (M) 3.530 4x.41 2.36 2.64 1.58 2 1.2.1379 Ford Escort (109.5) (56.0) (89.9) (4x10.4) (60.0) (67.0) (40.2) WHILE STOCKS LAST 97.0 45M 79 4x8.2 56 56 46 1 1.2.009 Suzuki
3.460 2.250 (M) 2.750 4x.32 1.77 2.10 1.19 1 1.2.39 Std 1140 bolt pattern (88.0) (57.1) (69.8) (4x8.2) (44.9) (53.5) (30.2)
SERIES: 1210 Suits U/J: 5.443X 26.99 x 61.93
- 45.0 (M) 89.1 4x10.0 63.0 63.0 45.9 1 2.2.686.1 Mazda
104.0 46.0 (M) 85.0 4x10.0 60.0 60.0 46.0 1 2.2.072 Toyota Tarago
- 46.0 (M) 78.0 4x8.0 55.0 55.0 38.1 1 2.2.2323 Toyota
104.0 47.0 (M) 84.0 4x10.3 59.4 59.4 29.3 1 2.2.063 BMW
3.46 2.252 (M) 2.75 4x.31 1.77 2.13 1.48 1 2.2.899 Nissan 1140 bolt pattern (88.0) (57.2) (69.9) (4x8.0) (44.9) (54.0) (37.6)
128.0 45.0 (M) 104.6 4x10.0 74.0 74.0 42.0 1 2.2.452.1 Mazda
D
D1
Type 1.
D2
KD3
L
D
N
D1
Type 2.
K
L
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 9
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
O.D Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1300 Suits U/J: K5L4R 26.99 x 74.61
4.29 2.204 (M) 3.54 4x.409 2.36 2.63 1.59 2 K2.2.1409 Ford Transit - Early (109.0) (56.0) (89.9) (4x10.4) (60.0) (67.0) (40.6)
4.72 1.575 (M) 3.78 4x.480 1.89 3.31 1.77 2 K2.2.022 Ford Transit (120.0) (40.0) (96.0) (4x12.2) (48.0) (84.0) (45.0)
4.72 2.205 (M) 3.78 4x.480 1.89 3.31 1.58 2 K2.2.024 Ford Transit - Late (120.0) (56.0) (96.0) (4x12.2) (48.0) (84.0) 40.0)
3.81 2.374 (M) 3.13 4x.375 2.02 2.39 1.39 1 K2.2.239 Std 1310 bolt pattern (97.0) (60.3) (79.4) (4x9.5) (51.3) (60.7) (35.3)
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
1.65 (M) 2.72 4x.31 2.36 1.38 1.97 1 2.2.062 Use in place of MDP (42.0) (69.0) (4x8.0) (60.0) (35.0) (50.0) Japanese PTO
3.46 2.252 (M) 2.75 4x.323 1.78 2.09 1.62 1 2.2.899.1 1140 bolt pattern (88.0) (57.2) (69.9) (4x8.2) (44.9) (53.5) (41.2)
90.0 47.0 (F) - - - - 50.0 2 2.2.900000 Blank Face Round
90.0 47.0 (F) 74.5 4x8.0 52.8 52.8 50.0 2 2.2.9048 DIN spec
3.62 2.000 (F) 2.88 4x.375 1.88 2.20 1.50 1 2.2.349 Detroit – 67R (92.07) (50.8) (73.2) (4x9.5) (47.8) (56.1) (38.1) Conversion to 1310
3.82 2.375 (M) 3.13 4x.375 2.01 2.39 1.39 1 2.2.329 Std 1310 bolt pattern (97.0) (60.3) (79.4) (4x9.5) (51.0) (60.7) (35.3)
3.82 2.375 (M) 3.13 4x.375 2.01 2.39 41.0 1 2.2.459 1310 30° (97.0) (60.3) (79.4) (4x9.5) (51.0) (60.7) (41.0)
3.93 1.969 (M) 3.19 4x.394 2.26 2.26 1.76 1 2.2.1309 Nissan Navara / 300ZX (100.0) (50.0) (81.0) (4x10.0) (57.3) (57.3) (44.7)
100.0 57.0 (F) 84.0 6x8.0 - - 50.0 2 2.2.10068 DIN spec.
100.0 57.0 (F) - - - - 53.0 2 2.2.100000 Blank Face Round
4.13 2.555 (M) 3.35 4x.393 1.97 2.71 1.65 1 2.2.8901 1310 – Isuzu Rodeo / Jackaroo (105.0) (64.9) (85.0) (4x10.0) (50.0) (69.0) (42.0)
D
D1
Type 1.
D2
KD3
L
D
N
D1
Type 2.
K
L
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 10
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES O.D Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76 Cont.
4.17 1.811 (M) 3.35 4x.32 2.20 2.52 1.62 1 2.2.799 Hilux (Replaces: TH.2.A1299) (106.0) (46.0) (85.0) (4x8.2) (56.0) (64.0) (41.2)
4.17 1.811 (M) 3.35 4x.40 2.36 2.36 1.62 1 2.2.799.1 Hilux (Replaces: TH.2.040) (106.0) (46.0) (85.0) (4x10.2) (60.0) (60.0) (41.2)
4.45 2.000 (F) 3.50 4x.50 2.47 2.47 1.62 1 211229X Double Cardan flange (113.0) (50.8) (88.9) (4x12.7) (62.9) (62.9) (41.2) Musso 800R1310.3
4.57 2.000 (F) 3.49 4x.50 2.47 2.47 1.65 1 2.2.939 Ford (116.0) (50.8) (88.7) (4x12.7) (62.8) (62.8) (41.8)
4.57 2.750 (M) 3.75 4x.438 2.41 2.87 1.39 1 2.2.479 1350 bolt pattern (116.0) (69.9) (95.3) (4x11.1) (61.2) (72.9) (35.3)
4.72 1.575 (M) 3.78 4x.48 1.89 3.27 1.69 1 2.2.060 Ford Transit - Front flange (120.0) (40.0) (96.0) (4x12.2) (48.0) (83.1) (43.0) Rear flange 2.2.061
100 50.0 81.1 4x10.2 57.3 57.3 56.0 2 2.2.1309A Nissan
115 46.0 (M) 93.3 4x11.2 66.0 66.0 40.0 1 2.2.799.4 Toyota
120.0 50.0 (M) - - - - 57.0 2.2.120000 Blank face – Nissan Round
120.0 56.0 (M) - - - - 56.0 2.2.061SF Blank face Ford Round
4.72 2.205 (M) 3.78 4x.48 1 2.2.061 Ford Transit - Rear flange (120.0) (56.0) (96.0) (4x12.2) (48.0) (83.2) (43.0) Front flange 2.2.060
120.0 57.0 (F) 101.5 4x10.2 71.8 71.8 58.0 2 2.2.120410 Mercedes Sprinter
4.724 2.555 (M) 3.74 4x.47 2.65 2.65 1.80 1 2.2.1169 MQ Patrol bolt pattern (120.0) (64.9) (95.1) (4x12.0) (67.2) (67.2) (45.8)
125.0 79.4 (F) - - - - 54.1 - 2.2.12500 Blank Face Round
5.03 1.772 (M) 4.11 4x.39 2.91 2.91 2.04 1 2.2.452 Mazda (128.0) (45.0) (104.6) (4x10.0) (74.0) (74.0) (52.0)
3.125 (F) 4.25 4x.438 3.00 3.00 2.83 2.83.188.1X Adaptor Flange (79.4) (108.0) (4x11.1) (76.2) (76.2) (60.5) 800R1310.1 – Saginaw
1.811 (M) 3.57 4x.32 2.36 2.68 2.91 2.83.288 Adaptor Flange (46.0) (90.7) (4x8.2) (60.0) (68.0) (73.9) 800R1310.2 – Toyota
115.0 65.0 (M) 94.75 4x.10.5 67.0 67.0 49.20 2.21.3191 Double Cardan Flange
Landrover Discovery
D
D1
Type 1.
D2
KD3
L
D
N
D1
Type 2.
K
L
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 11
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
OD Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
100.0 57.0 (F) - - - - 55.0 2 3.2.10000.1350 Blank Face Round
4.52 1.811(M) 3.56 4x.45 2.36 2.68 1.81 1 3.2.A1139 Land Cruiser (115.0) (46.0) (91.1) (4x11.5) (60.0) (68.0) (46.0)
4.56 2.750 (M) 3.75 4x.44 2.41 2.87 1.56 1 3.2.119 Std 1350 bolt pattern (116.0) (69.9) (95.3) (4x11.2) (61.2) (72.9) (39.6)
5.12 2.677 (M) 4.25 4x.44 3.00 3.00 1.61 1 3.2.1699 Ford (130.0) (68.0) (107.9) (4x12) (76.2) (76.2) (41.0) 5.12 2.000 (F) 4.25 4x.50 3.00 3.00 1.77 1 3.2.1579A Ford Transit (130.0) (50.8) (107.9) (4x12.7) (76.2) (76.2) (45.0)
120.0 57.0 (F) 101.5 4x10.2 71.8 71.8 66.0 1 3.2.120410 Mercedes Sprinter
120.0 75.0 (F) - - - - 56.0 3.2.120000.1350 Blank Face Round
5.12 2.000 (F) 4.25 3.00 3.00 1.62 3.83.024X Double Cardan Flange (130.0) (50.8) (107.9) (4xM12x1.75) (76.2) (76.2) (41.3) Ford “F” Series
5.12 2.677 (F) 4.25 3.00 3.00 1.62 3.83.025X Double Cardan Flange (130.0) (68.0) (107.9) (4xM12x1.75) (76.2) (76.2) (41.3) Dodge Ram
5.12 3.125 (F) 4.25 3.00 3.00 1.62 3.83.3281X Double Cardan Flange (130.0) (79.4) (107.9) (4xM12x1.75) (76.2) (76.2) (41.3) Saginaw
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
100.0 57.0 (M) - - - - (55.0) 2 3.2.10000.1410 Blank Face Round
100.0 57.0 (F) 84.0 6x8.0 - - 65.0 2 3.2.10068 100mm OD, DIN spec.
4.566 2.752 (M) 3.75 4x.44 2.41 2.87 1.69 1 3.2.159 Std 1410 bolt pattern (116.0) (69.9) (95.3) (4x11.2) (61.2) (72.9) (42.9)
120.0 70.0 (M) 100.0 4x12.0 64.3 76.6 55.0 1 3.2.352.1410 Mitsubishi
120.0 75.0 (F) - - - - 55.6 3.2.120000.1410 120mm OD, Blank face-Round
120.0 75.0 (F) 101.5 8x10.0 - - 55.6 1 3.2.120810.1410 120mm OD, DIN spec.
140.0 70 (M) 115.0 4x11.8 78.4 84.1 42 2 3.2.3100 Hino
4.724 3.150 (M) 3.94 4x.40 2.32 3.19 2.24 2 3.2.3900 Isuzu (120.0) (80.0) (100.0) (4x10.2) (59.0) (81.0) (57.0)
D
D1
Type 1.
D2
KD3
L
D
N
D1
Type 2.
K
L
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 12
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
OD Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35 Cont.
5.748 3.752 (M) 4.75 4x.50 3.05 3.64 2.00 1 3.2.429 1480 bolt pattern (30°) (146.0) (95.3) (120.7) (4x12.7) (77.5) (92.4) (50.8)
150.1 3.54 (F) - - - - 2.83 3.2.150000.1410 Blank Face Round (90.0) (71.8)
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
120.0 75.0 (F) - - - - - 3.2.12000.1480 Blank Face Round
4.566 2.750 (M) 3.750 4x.438 2.41 2.87 2.38 2 3.2.104 Std 1410 bolt pattern (116.0) (69.9) (95.3) (4x11.1) (61.2) (72.9) (60.5)
120.0 70.0 (M) 100.0 4x12.2 64.3 76.6 65.0 1 3.2.352.1480 Mitsubishi
120.0 75.0 (F) 101.5 8x10.0 - - 60.0 1 3.2.120810.1480 DIN spec.
120 None 100.0 4x11.2 57.3 81.1 63.5 3 687.30.2.120411 Cross Tooth
120 75.0 (F) 101.5 8X10.2 71 2 687.30.2.120810
5.91 3.54(F) - - - - 73.0 1 3.2.150000.1480 Blank Face Round (150.1) (90.0)
120.0 80.0 (M) 100.0 4x12.2 58.8 80.9 65.0 1 3.2.014 Isuzu
135.0 80.0 (M) 109.1 4x12.0 55.0 95.2 69.0 1 3.2.013 Isuzu
5.750 3.750 (M) 4.750 4x.500 3.06 3.64 2.00 1 3.2.479 Std 1480 bolt pattern (146.0) (95.2) (120.6) (4x12.7) (77.6) (92.4) (50.8)
5.750 3.750 (M) 4.750 4x.500 3.06 3.64 687.30.2.1510.CV Double Cardan Flange (146.0) (95.2) (120.6) (4x12.7) (77.6) (92.4) 120.0 75.0 (M) 101.5 8x10.2 - - 72.0 1 687.30.2.120810.CV Double Cardan Flange (50.8)
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 13
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES OD Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1500 Suits U/J: K5GB15R 39.70 x 115.90
6.625 6.125 (M) 8x.375 3.06 3.64 - 2.75 1 4.2.309 (168.3) (155.6) (8x9.5) (77.6) (92.4) (69.9) WHILE STOCKS LAST
SERIES: 1510 Suits U/J: K5GB22R 39.7 x 115.90
4.724 2.953 (F) 4.00 8x.394 - - 2.87 1 K4.2.120810 DIN spec.with 508.64 (120.0) (75.0) (101.5) (8x10.0) (72.9) Cap Bolts 5/16” BSF x 5/8
130.0 82.5 (F) 112.0 8x10.2 - - 67.0 1 K4.2.130810 Mercedes
5.750 3.750 (M) 4.750 4x.500 3.06 3.64 1.57 2 K4.2.001 Short Coupled (146.0) (95.2) (120.6) (4x12.7) (77.6) (92.4) (40.0)
5.750 3.750 (M) 4.750 4x.500 3.06 3.64 2.50 2 K4.2.GB239 Standard (146.0) (95.2) (120.6) (4x12.7) (77.6) (92.4) (63.5)
5.905 3.543 (F) 5.12 8x.476 - - 3.54 2 K4.2.150812 DIN 150 (150.0) (90.0) (130.0) (8x12.1) (90.0)
150.0 90 (F) 72.0 K4.2.150000 Blank Face Round
6.889 6.625 (M) 6.125 8x.375 3.62 2 K4.2.1610 1610 Face (175.0) (168.3) (155.6) (8x9.5) (92.0)
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
145.0 80.0 (M) 125.0 4x13.2 80.3 95.8 60 1 4.2.847 Hino
5.905 3.543 (F) 5.11 8x.472 - - 3.14 2 4.2.150812 DIN spec. (150.0) (90.0) (130.0) (8x12.0) (80.0)
5.748 3.750 (M) 4.750 4x.500 3.05 3.64 1.50 1 4.2.679 Close couple (8°) (146.0) (95.3) (120.7) (4x12.7) (77.5) (92.4) (38.1)
5.748 3.750 (M) 4.750 4x.500 3.05 3.64 2.00 1 4.2.669 Std 1550 bolt pattern (146.0) (95.3) (120.7) (4x12.7) (77.5) (92.4) (50.8)
6.889 6.626 (M) 6.13 8x.375 - - 2.00 2 4.2.689 1610 bolt pattern (175.0) (168.3) (155.6) (8x9.5) (50.8)
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 14
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
OD Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
5.905 3.543 (F) 5.12 8x.476 3.35 1 5.2.150812 DIN spec (150.0) (90.0) (130.0) (8x12.1) (85.0)
171.0 90.0 (M) 140.0 4x14.0 74.5 118.0 70.0 1 5.2.244 Isuzu
180.0 90.0 (M) 147.0 4x14.0 83.0 122.0 70.0 1 5.2.180414.1 Mitsubishi
6.889 6.626 (M) 6.13 8x.375 - - 1.88 1 5.2.379 Close couple, 1610 bolt pattern (175.0) (168.3) (155.6) (8x9.5) (47.6)
6.889 6.626 (M) 6.13 8x.375 - - 2.75 1 5.2.279 Std 1610 bolt pattern (175.0) (168.3) (155.6) (8x9.5) (69.9)
8.000 7.752 (M) 7.25 8x.375 - - 1.88 1 5.2.619 Close couple, 1710 bolt pattern (203.2) (196.9) (184.2) (8X9.5) (47.6) Limited quantities
8.000 7.752 (M) 7.25 8x.375 - - 2.75 1 5.2.629 1710 bolt pattern (203.2) (196.9) (184.2) (8x9.5) (69.9)
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
150.0 - 130.0 4x13.2 86.0 122.9 81.0 3 6.2.15 KV Cross tooth
165.0 95.0 (F) 140.0 8x16.2 - - 100.0 1 6.2.165816 DIN spec
6.890 6.625 (M) 6.125 8x.375 - - 3.858 1 K56.2.GB99 1610 bolt pattern (175.0) (168.2) (155.8) (8x9.5) (98.0)
180.0 110.0 (F) 155.51 8x14.2 - - 85.0 1 6.2.180814 DIN spec
180.0 110.0 (F) - - - - 90.0 1 6.2.1800000 Blank Face Round
180.0 110.0 (F) 155.51 10x16.2 - - 100.0 1 6.2.1801016 DIN spec
180.0 110.0 (F) 155.5 8X14.2 2 6.2.180814.1
192.0 90.0 (M) 156.0 4x16.2 80.0 134.0 80.0 1 6.2.192416 Mitsubishi
197.0 100.0 (M) 160.0 4x16.2 91.8 131.1 80.0 1 6.2.197416.1 Isuzu
203.0 120.0 (M) 180.0 6x13.2 2 6.2.203613 Mitsubishi
7.992 7.752 (M) 7.25 8x.375 - - 2.00 1 6.2.769 Close couple 1710 bolt pattern (203.0) (196.9) (184.2) (8x9.5) (50.8)
7.992 7.752 (M) 7.25 8x.375 - - 3.00 1 6.2.749 Std 1710 bolt pattern (203.0) (196.9) (184.2) (8x9.5) (76.2)
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 15
SPICER
September
2014 © Driveline Services Australia Pty Ltd
FLANGE YOKES
OD Spigot PCD Holes Bolt Pattern F-C N K D D1 D2 D3 L Type Part No. Notes / Suggestions
SERIES: 1760 Suits U/J: 5.407X 49.21 x 177.80
7.992 7.752 (M) 7.25 12x.625 - - 3.38 2 6.3.2.19 STD 1810 bolt pattern (203.0) (196.9) (184.2) (12x11.1) (85.7)
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.75
180.0 - 150.0 4x15.2 86.0 122.9 88.0 3 6.5.2.15 KV Cross tooth
180.0 110.0 (F) 155.0 8x14.0 - - 92.0 1 6.5.2.180814 DIN Spec
180.0 110.0 (F) 155.0 10x16.0 - - 92.0 1 6.5.2.180816 DIN Spec
7.992 7.752 (M) 7.25 12x.438 - - 3.38 2 6.5.2.329 Std 1810 bolt pattern (203.0) (196.9) (184.2) (12x11.1) (85.7)
240.0 160.0 (M) - - - - 90.0 6.5.2.2400000 Blank Face Round
SERIES: 1880 Suits U/J: 5.308X 55.50 x 205.59
9.500 7.000 (M) 8.25 8x.625 - - 2.50 1 8.2.119 Close couple, 1880 bolt pattern (241.3) (177.8) (209.6) (8x15.9) (63.5) WHILE STOCKS LAST
9.500 7.000 (M) 8.25 8x.625 - - 3.59 1 8.2.109 STD 1880 bolt pattern (241.3) (177.8) (209.6) (8x15.9) (91.3)
Flange can have 4,6,8,10 or 12spaced holes
SPICER CATALOGUE PAGE:- 16
SPICER
September
2014 © Driveline Services Australia Pty Ltd
AUTOMOTIVE SLIPYOKES
Spline C-EOS LTH Hub S L L1 O Part No. Application
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
0.875 x 16 5.53 4.53 1.19 1.3.2418 Escort (22.23 x 16) (140.5) (115.1) (30.2) WHILE STOCKS LAST 1.113 x 25 5.87 4.73 1.375 1.3.8431X Early Transit (28.27 x 25) 149 120 34.92 WHILE STOCKS LAST
SERIES: 1210 Suits U/J: 5.443X 26.99 x 61.93
0.998 x 22 Inv 6.00 4.92 1.37 2.3.0686X Mazda (20 + 2 Blank teeth) (25.35x 22) (152.4) (125.0) (34.9)
1.005 x 24 Inv 6.00 4.92 1.37 2.3.1224X Nissan (22 + 2 Blank teeth) (25.52 x 24) (152.4) (125.0) (34.9)
1.102 x 21 Inv 6.00 4.92 1.49 2.3.2321X Toyota (21 Involute Spline) (27.99 x 21) (152.4) (125.0) (37.9)
1.113 x 25 Inv 5.71 4.21 1.50 2.3.3318 Mazda (28.27 x 25) (145.0) (107.0) (38.1)
1.176 x 27 Inv 6.02 4.05 1.5 2.3.1188 Holden (29.87 x 27) (153.0) (103.0) (38.1)
SERIES: 1300 Suits U/J: K5L4R 26.99 x 74.61
1.113 x 25 6.06 5.04 1.37 K2.3.4798 Ford Transit (28.27 x 25) (154.0) (128.0) (34.9) WHILE STOCKS LAST
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
0.998 x 22 Inv 5.98 4.64 1.37 2.3.3328 Mazda (25.35 x 22) (152.0) (118.0) (34.9)
1.005 x 24 Inv 6.02 4.64 1.38 2.3.13461X Nissan (25.52 x 24) (153.0) (118.0) (35.0)
1.118 x 26 Inv 6.06 4.56 1.49 2.3.13891X Nissan (26.13 x 26) (154.0) (116.0) (37.9)
28.4x 21 Inv 6.02 4.21 1.50 2.3.9701X Toyota (27.96 x 21) (153.0) (107.0) (38.0)
28.2x 25 Inv 6.53 5.59 1.38 2.3.8431X Ford Transit (28.27 x 25) (166.0) (142.0) (35.0) 1.113 x 25 Inv 5.98 4.64 1.50 2.3.3318.1 Ford/Mazda (28.27 x 25) (152.0) (118.0) (38.0)
SPICER CATALOGUE PAGE:- 17
SPICER
September
2014 © Driveline Services Australia Pty Ltd
AUTOMOTIVE SLIP YOKES Spline C-EOS LTH Hub S L L1 O Part No. Application
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76 Cont.
1.190 x 27 Inv 5.47 4.53 1.49 2.3.6081X 1310 – 2R Holden (30.2 x 27) (139.0) (115.0) (38.0)
1.22 x 28 Inv 6.50 5.71 1.50 2.3.8251X Ford C4 – Top Loader (30.98 x 28) (165.1) (145.0) (38.1)
1.284 x 30 Inv 6.18 4.64 1.65 2.3.13311X VL Turbo / Nissan (32.61 x 30) (157.0) (118.0) (41.9)
1.312 x 30 Inv 8.06 6.61 1.68 2.3.3575X Chrysler (33.32 x 30) (204.7) (168.0) (42.7)
1.382 x 31 Inv 5.98 4.72 1.69 2.3.15631X C6 Limited Stocks (35.1 x 31) (152.0) (120.0) (42.8)
1.397 x 32 Inv 7.08 5.39 1.89 2.3.9131X Turbo 400 (35.48 x 32) (180.0) (137.0) (47.9)
SERIES: 1330 Suits U/J: RUJ3002 26.99 x 92.08
1.190 x 27 Inv 6.85 4.72 1.50 2.3.9921X Holden Power Glide (30.22 x 27) (174.0) (120.0) (38.1)
1.220 x 28 Inv 5.91 5.06 1.50 2.3.5981X Ford C4, Top Loader (30.98 x 28) (150.0) (128.5) (38.1)
1.382 x 31 Inv 7.00 4.72 1.69 2.3.6041X C6, FMX (35.1 x 31) (178.0) (120.0) (42.8)
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.176 x 27 Inv 6.93 5.70 1.50 3.3.4281X Holden (29.87 x 27) (176.0) (145.0) (38.1)
1.382 x 31 Inv 6.44 5.23 1.68 3.3.2491X C6, FMX (35.10 x 31) (163.5) (133.0) (42.7)
1.397 x 32 Inv 7.91 5.91 1.89 3.3.2951X GM - USA (35.48 x 32) (201.0) (150.0) (47.9)
1.397 x 32 Inv 7.91 5.91 1.89 3.3.1538 Turbo 400 – Counter Bored (35.48 x 32) (201.0) (150.0) (47.9)
SERIES: 3R Suits U/J: 114.3105 28.58 x 65.10 (Internal)
1.190 x 27 5.51 4.85 1.50 3R.3.6081X Holden (29.87 x 27) (140.0) (123.2) (38.1)
1.397 x 32 7.60 6.69 1.88 3R.3.9131X Turbo 400 (29.87 x 27) (193.0) (170.0) (47.8)
SERIES: 7290 Suits U/J: 114.232 28.58 x 66.67 (Internal)
1.312 x 30 7.56 6.56 1.68 729.3.1932X Conversion Joints (33.32 x 30) (192.0) (166.6) (42.6) Chrysler Series 21R U/J 405002 Series 3R U/J 405001, 1330 U/J 401008 Series 1310 U/J 401009
SPICER CATALOGUE PAGE:- 18
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP YOKES
Spline C-EOS LTH Angle S L L1 ° Part No. Notes / Suggestions
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
1.060 x 16 4.33 3.47 K1.3.A360 K1.42.GB1901 (26.92 x 16) (110.0) (88.1) K1.42.GB1921
SERIES: 1210 Suits U/J: 5.443X 26.99 x 61.93
1.250 x 16 6.40 5.07 2.3.8861KX 2.40.1741 (31.75 x 16) (162.5) (129.0)
1.250 x 16 8.02 6.69 2.3.8961KX 2.40.2301 (31.75 x 16) (203.6) (170.0)
SERIES: 1300 Suits U/J: K5L4R 26.99 x 74.61
1.375 x 16 5.50 4.33 20° K2.3.A610 Can use 687.15 Assembly (34.93 x 16) (139.7) (110.0) 2.40.1031 / 2.40.2701 / 2.40.1041
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
1.250 x 16 6.56 5.07 30° 2.3.4441KX 2.40.1771 Splined D/cap (31.75 x 16) (166.6) (129.0)
1.375 x 16 5.38 4.29 20° 2.3.128KX 2.40.1031 / 2.40.2701 / 2.40.1041 (34.93 x 16) (136.7) (109.0)
1.375 x 16 6.88 5.31 30° 2.3.5221KX 2.40.2451 / 2.40.1221 / 2.40.1711 (34.93 x 16) (174.8) (135.0)
1.375 x 16 7.88 6.29 30° 2.3.5821KX 2.40.3081 / 2.40.1851 / 2.40.2051 (34.93 x 16) (200.2) (160.0)
1.375 x 16 6.54 5.35 30° 2.3.3658KX 2.40.3061 (34.93 x 16) (166.0) (136.0)
1.375 x 16 4.10 3.11 20° 2.3.348KX 2.82.21 (34.93 x 16) (104.1) (79.0)
1.500 x 16 6.54 ? 2.3.3668KX 2.82.002 (38.10 x 16) (166.0) ( ?)
A number of differentdustcap designs are possible.
Enquire with sales staff if a particular type is required.
SPICER CATALOGUE PAGE:- 19
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP YOKES
Spline C-EOS LTH Angle S L L1 ° Part No. Notes / Suggestions
SERIES: 1330 Suits U/J: RUJ3002 26.99 x 92.08
1.375 x 16 6.00 4.96 2.3.7961KX 2.40.1221 / 2.40.1711 / 2.40.2451 (34.93 x 16) (152.4) (126.0)
1.375 x 16 7.50 6.38 17° 2.3.7481KX 2.40.1851 / 2.40.3081 / 2.40.2051 (34.93 x 16) (190.5) (162.0)
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.375 x 16 5.81 4.53 3.3.1501KX (34.93 x 16) (147.6) (115.0)
1.500 x 16 3.94 2.72 20° 3.3.388KX 3.82.61 (38.10 x 16) (100.1) (69.0)
1.500 x 16 5.81 4.53 20° 3.3.598KX 3.40.1101 / 3.40.1471 / 3.40.3901 (38.10 x 16) (147.6) (115.0)
1.500 x 16 7.31 6.29 20° 3.3.488KX 3.40.1611 / 3.40.3891 / 3.40.1491 (38.10 x 16) (185.7) (160.0)
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
1.375 x 16 5.25 4.05 20° 3.3.788KX 2.40.1041 (34.93 x 16) (133.4) (103.0)
1.500 x 16 3.90 2.83 20° 3.3.468KX 3.82.81 (38.10 x 16) (99.1) (72.0)
1.500 x 16 5.25 4.05 20° 3.3.2041KX 3.53.1031 (38.10 x 16) (133.4) (103.0)
1.500 x 16 6.50 5.31 20° 3.3.118KX 3.40.1101 / 3.40.3901 (38.10 x 16) (165.1) (135.0)
1.500 x 16 7.81 6.46 28° 3.3.508KX 3.40.1611 / 3.40.3891 / 3.40.1491 (38.10 x 16) (198.4) (164.0)
1.560 x 16 6.81 5.47 21° 3.3.1701KX (39.62 x 16) (173.0) (139.0)
A number of differentdustcap designs are possible.
Enquire with sales staff if a particular type is required.
SPICER CATALOGUE PAGE:- 20
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP YOKES
Spline C-EOS LTH Angle S L L1 ° Part No. Notes / Suggestions
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
1.560 x 16 6.81 5.35 21° 3.3.1601KX 3.40.1571 (39.62 x 16) (173.0) (136.0)
1.560 x 16 9.50 7.52 35° 3.3.1641KX 3.40.1391 (39.62 x 16) (241.3) (191.0)
1.560 x 16 11.50 9.45 35° 3.3.1661KX 3.40.1411 (39.62 x 16) (292.1) (240.0)
1.750 x 16 6.81 5.55 22° 3.3.1505KX 4.40.761 / 3.82.1505 Splined D/cap (44.45 x 16) (173.0) (141.0)
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
1.750 x 16 6.88 5.47 22° 4.3.1241KX 4.40.761 (44.45 x 16) (174.8) (139.0)
1.750 x 16 10.06 8.03 35° 4.3.1431KX 4.40.721 (44.45 x 16) (255.6) (204.0)
2.500 x 16 3.50 2.56 8° 4.3.1261KX Close couple (63.50 x 16) (88.9) (65.0) 4.82.191 Yoke shaft
SERIES: 1510 Suits U/J: K5GB22R 39.70 x 115.90
1.750 x 16 6.64 5.31 K4.3.A1120 4.40.761 (44.45 x 16) (168.7) (135.0)
1.750 x 16 9.13 7.05 K4.3.A1140 Use K4.6.001 Assy (44.45 x 16) (231.9) (179.0) No longer available
A number of differentdustcap designs are possible.
Enquire with sales staff if a particular type is required.
SPICER CATALOGUE PAGE:- 21
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP YOKES Spline C-EOS LTH Angle S L L1 ° Part No. Notes / Suggestions
SERIES: 1650 Suits U/J: 5.165X 41.28 x 142.00
2.000 x 16 9.50 - - 5.3.1681KX (50.80 x 16) (241.3)
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
2.000 x 16 7.81 6.30 22° 5.3.108KX 5.82.661 / 5.82.921 (50.80 x 16) (198.4) (160.0)
2.000 x 16 9.31 6.26 30° 5.3.288KX 7C.40.703 (50.80 x 16) (236.5) (159.0)
2.000 x 16 10.81 8.27 35° 5.3.2261KX 5.40.1011 (50.80 x 16) (274.6) (210.0)
2.000 x 16 11.94 9.05 45° 5.3.2141KX 5.40.1041 / 5.82.751.2 / 5.82.751.6 (50.80 x 16) (303.3) (230.0)
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
2.500 x 16 9.59 7.78 22° 6.3.2671KX 6.40.541 (63.50 x 16) (243.6) (197.6)
2.500 x 16 10.71 7.40 45° 6.3.3021KX Can shorten 6.3.2551KX (63.50 x 16) (272.0) (188.0)
2.500 x 16 11.69 9.37 30° 6.3.2651KX 6.40.521 (63.50 x 16) (296.9) (238.0)
2.500 x 16 11.71 8.38 45° 6.3.2571KX Can shorten 6.3.2551KX (63.50 x 16) (297.4) (212.9)
2.500 x 16 12.71 9.41 45° 6.3.2551KX (63.50 x 16) (322.8) (239.0)
3.250 x 18 4.13 2.68 8° 6.3.1661KX Close couple : 6.82.341 Yoke shaft (82.55 x 18) (104.9) (68.0) Can use 6.03.167 Assy
A number of differentdustcap designs are possible.
Enquire with sales staff if a particular type is required.
SPICER CATALOGUE PAGE:- 22
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP YOKES
Spline C-EOS LTH Angle S L L1 ° Part No. Notes / Suggestions
SERIES: 1760 Suits U/J: 5.407X 49.21 x 177.80
2.500 x 16 11.16 9.22 30° 6.3.3.21KX 6.40.521 (63.50 x 16) (283.5) (234.0)
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.75
3.000 x 16 10.25 7.76 30° 6.5.3.1351KX 6.5.40.201 (76.20 x 16) (260.4) (197.0)
3.000 x 16 11.88 9.44 30° 6.5.3.1371KX 6.5.40.191 (76.20 x 16) (301.8) (240.0)
3.250 x 18 5.38 3.89 12° 6.5.3.1451KX Close couple
(82.55 x 18) (136.7) (99.0) 6.5.82.511.1 Yoke
SERIES: 1800 Suits U/J: 5.124X 59.10 x 167.49
3.000 x10 10.0 6.5.3.38KX No Longer Available
(76.20 x 10) (254.0) WHILE STOCKS LAST Use 6.5.6.1800 Assy
SERIES: 1850 Suits U/J: 5.185X 55.55 x 205.59
3.000 x 16 10.03 22° 8.3.31KX Limited quantities
(76.20 x 16) (254.8) WHILE STOCKS LAST 8.40.101
SERIES: 1880 Suits U/J: 5.308X 55.55 x 205.59
3.000 x 16 11.66 22° 8.3.411KX 8.40.101 (76.20 x 16) (296.2)
A number of differentdustcap designs are possible.
Enquire with sales staff if a particular type is required.
SPICER CATALOGUE PAGE:- 23
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP ASSEMBLIES
Tube Butt Spline C-W Total Size B Size Comp Slip Type Part No. Notes / Suggestions
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
2.000 x .095 1.81 1.060 x 16 8.07 2.87 1 K1.6.1901 K1.3.A360 & K1.42.GB1901 (50.8 x 2.41) (46.0) (26.92 x 16) (205.0) (73.0)
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
2.000 x .083 1.84 1.375 x 16 7.80 2.87 1 2.6.2451 2.3.5221KX & 2.40.2451 (50.8 x 2.1) (46.7) (34.95 x 16) (198.1) (73.0)
2.000 x .095 1.81 1.375 x 16 6.28 2.00 1 2.6.2701 2.3.128KX & 2.40.2701 (50.8 x 2.41) (46.0) (34.95 x 16) (159.5) (50.8)
2.000 x .095 1.81 1.375 x 16 9.21 3.93 1 2.6.3081 2.3.5821KX & 2.40.3081 (50.8 x 2.41) (46.0) (34.95 x 16) (234.0) (100.0)
2.500 x .083 2.34 1.375 x 16 8.00 2.87 1 2.6.1711 2.3.5221KX & 2.40.1711 (63.5 x 2.1) (59.5) (34.95 x 16) (203.2) (73.0)
2.500 x .083 2.34 1.375 x 16 9.13 3.93 1 2.6.1851 2.3.5821KX & 2.40.1851 (63.5 x 2.1) (59.5) (34.95 x 16) (232.0) (100.0)
2.500 x .095 2.31 1.375 x 16 6.42 2.00 1 2.6.2891 2.3.128KX & 2.40.2891 (63.5 x 2.41) (58.9) (34.95 x 16) (163.0) (50.8)
2.500 X .095 1.500X18 8.72 3.50 2 2.6.1310 European Type (63.5 x 2.41) 38x18 Inv (221.5) (88.9)
3.000 x .064 2.87 1.375 x 16 8.07 2.87 1 2.6.1221 2.3.5221KX & 2.40.1221 (76.2 x 1.7) (73.1) (34.95 x 16) (205.0) (73.0)
SERIES: 1350 Suits U/J: 5.178 30.16 x 92.08
3.000 x .083 2.84 1.500 x 16 7.16 2.00 1 3.6.3502 3.3.598KX & 3.40.1101 (76.2 x 2.1) (72.2) (38.1 x 16) (182.0) (50.8)
3.000 x .083 2.84 1.500 x 16 8.46 3.50 1 3.6.3503 3.3.488KX & 3.40.1611 (76.2 x 2.1) (72.2) (38.1 x 16) (215.0) (88.9)
3.000 x .095 2.82 1.500 x 16 7.32 2.00 1 3.6.3504 3.3.598KX & 3.40.3901 (76.2 x 2.41) (71.6) (38.1 x 16) (186.0) (50.8)
3.000 x .095 2.82 1.500 x 16 8.46 3.50 1 3.6.3501 3.3.488KX & 3.40.3891 (76.2 x 2.41) (71.6) (38.1 x 16) (215.0) (88.9)
B
Compressed Compressed
Type 1 Type 2
SPICER CATALOGUE PAGE:- 24
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP ASSEMBLIES
Tube Butt Spline C-W Total Size B Size Comp Slip Type Part No. Notes / Suggestions
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
3.000 x .083 2.84 1.500 x 16 7.59 2.16 1 3.6.4102 3.3.118KX & 3.40.1101 (76.2 x 2.1) (72.2) (38.1 x 16) (193.0) (55.0)
3.000 x .083 2.84 1.500 x 16 8.70 3.50 1 3.6.4104 3.3.508KX & 3.40.1611 (76.2 x 2.1) (72.2) (38.1 x 16) (221.0) (88.9)
3.000 x .095 2.82 1.500 x 16 7.48 2.55 1 3.6.4101 3.3.118KX & 3.40.3901 (76.2 x 2.41) (71.6) (38.1 x 16) (190.0) (65.0)
3.000 x .095 2.82 1.500 x 16 8.70 3.50 1 3.6.4103 3.3.508KX & 3.40.3891 (76.2 x 2.41) (71.6) (38.1 x 16) (221.0) (88.9)
3.500 x .095 3.32 1.97 x 18 Inv 10.03 4.00 2 3.6.1410 Euro style Butt can be machined (88.9 x 2.41) (84.3) (50.0 x 18) (255.0) (101.6) to suit 3” tube
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
3.500 x .095 3.32 1.77 x 16 Inv 8.54 4.00 2 687.30.6 Euro style (88.9 x 2.4) (84.3) (45.0 x 16) (217.0) (101.6)
3.500 x .095 3.32 1.97 x 18 Inv 10.03 4.00 2 687.30.6.1 Euro style (88.9 x 2.4) (84.3) (50.0 x 18) (255.0) (101.6) Butt can be machined to suit 3” tube
SERIES: 1510 Suits U/J: K5GB22R 39.70 x 115.90
3.500 x .095 3.32 2.16 x 20 Inv 11.61 2 K4.6.001 Euro style (88.9 x 2.4) (84.3) (55.0 x 20) (295.0)
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
3.500 x .095 3.32 1.750 x 16 7.875 2.360 2 5.155X Euro style with steel seal area (88.9 x 2.4) (84.3) (44.45 x 16) (200.0) (60)
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
3.500 x .134 3.24 2.00 x 16 11.14 3.93 1 5.6.002 5.3.288KX & 7C.40.703 (88.9 x 3.4) (82.3) (50.8 x 16) (283.0) (100.0)
3.500 x .134 3.24 2.00 x 16 12.08 4.72 1 5.6.001 5.3.2261KX & 5.40.1011 (88.9 x 3.4) (82.3) (50.8 x 16) (307.0) (120.0)
B
Compressed Compressed
Type 1 Type 2
SPICER CATALOGUE PAGE:- 25
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SLIP ASSEMBLIES Tube Butt Spline C-W Total Size B Size Comp Slip Type Part No. Notes / Suggestions
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
4.090 x .180 3.74 2.50 x 16 11.02 3.88 1 6.6.003 6.3.2671KX & 6.40.541 (103.8 x 4.57) (95.1) (63.5 x 16) (280.0) (98.5)
4.090 x .180 3.74 2.50 x 16 12.99 5.25 1 6.6.001 6.3.2651KX & 6.40.521 (103.8 x 4.57) (95.1) (63.5 x 16) (330.0) (133.3)
4.090 x .180 3.74 2.50 x 16 14.00 5.25 1 6.6.002 6.3.2551KX & 6.40.521 (103.8 x 4.57) (95.1) (63.5 x 16) (356.0) (133.3)
SERIES: 1800 Suits U/J: 5.124X 59.10 x 167.49
90 x 5 3.15 3.00 x 10 14.05 3.25 1 6.5.6.1800 (80.1) (76.2 x 10) (357.0) (82.5)
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.75
4.590 x .180 4.24 3.00 x 16 11.84 3.38 1 6.5.6.002 6.5.3.1351KX & 6.5.40.201 (116.6 x 4.57) (107.7) (76.2 x 16) (300.7) (85.8)
4.590 x .095 4.24 3.00 x 16 13.62 5.00 1 6.5.6.001 6.5.3.1371KX & 6.5.40.191 (116.6 x 4.57) (107.7) (76.2 x 16) (346.0) (127.0)
SERIES: RPL25 Suits U/J: CP25RPLS 52.33 x 208.28
4.590 x .180 4.24 3.00 x 16 12.79 3.54 1 25RP.6.001 (116.6 x 4.57) (107.7) (76.2 x 16) (325.0) (90.0)
SERIES: SPL170 Suits U/J: SPL170X 55.00 x 164.00
120 x 5 4.34 3.46 x 34 Inv 12.20 7.68 2 170.6.001 Machine Butt use 120x6 (130.0) (88.0 x 34) (310.0) (195.0)
SERIES: SPL250 Suits U/J: SPL250X 60.00 x 163.00
132 x 6 4.74 3.85 x 38 Inv 10.87 4.33 2 250.6.001 Machine Butt use 130x6 (120.3) (98.0 x 38) (276.0) (110.0)
B
Compressed Compressed
Type 1 Type 2
SPICER CATALOGUE PAGE:- 26
SPICER
September
2014 © Driveline Services Australia Pty Ltd
L
Compressed
Type 2 Type 1
YOKE SHAFT AND SLIP YOKE ASSEMBLIES – LESS JOINTS C-C Total Spline Angle L Slip Size Type ° Part No. Notes / Suggestions
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
6.220 1.57 1.37 x 16 1 20° 2.03.158LZ (158.0) (39.8) (34.7 x 16)
7.48 1.57 1.25 x 16 1 18° 2.03.190 (189.9) (39.8) (31.7 x 16) WHILE STOCKS LAST
6.38 0.98 1.37 x 16 1 20° 2.03.162LZ 2.3.348KX & 2.82.21 (162.0) (24.8) (34.7 x 16)
7.56 2.09 2.09 x 16 1 20° 2.03.192LZ 2.3.128KX & 2.82.A111 (192.0) (53.0) (53.0 x 16)
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
6.38 0.62 1.50 x 16 1 8° 3.03.162LZ 3.3.388KX & 3.82.61 (162.0) (15.7) (38.1 x 16)
7.99 2.12 1.50 x 16 1 22° 3.03.203LZ 3.3.598KX & 3.82.181 (202.9) (53.8) (38.1 x 16)
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
6.10 0.79 1.50 x 16 1 8° 3.03.155LZ 3.3.468KX & 3.82.81 (154.9) (20.0) (38.1 x 16)
7.40 1.37 1.50 x 16 1 22° 3.03.188LZ 3.3.2041KX & 3.82.145 (187.9) (34.7) (38.1 x 16)
8.54 2.00 1.50 x 16 1 22° 3.03.217LZ 3.3.118KX & 3.82.145 (216.9) (50.8) (38.1 x 16)
9.84 1.37 1.50 x 16 1 22° 3.03.250LZ 3.3.508KX & 3.82.145 (249.9) (34.7) (38.1 x 16)
13.18 4.33 2 25° 3.03.335LZ Euro style can be shortened to (334.7) (109.9) (50 x 18 Inv) 230mm C-C
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
9.13 1.18 1.56 x 16 1 3.03.232LZ 3.3.1601KX & 3.82.1504 (231.9) (29.9) (39.6 x 16)
9.96 2 25° 687.30.03.253LZ
(253.0)
13.18 4.33 2 25° 687.30.03.335LZ Euro style can be shortened to (334.7) (109.9) (50 x 18 Inv) 230mm C-C
SPICER CATALOGUE PAGE:- 27
SPICER
September
2014 © Driveline Services Australia Pty Ltd
L
Compressed
Type 2 Type 1
YOKE SHAFT AND SLIP YOKE ASSEMBLIES – LESS JOINTS
C-C Total Spline Angle L Slip Size Type ° Part No. Notes / Suggestions
SERIES: 1510 Suits U/J: K5GB22R 39.70 x 106.38
6.69 1.38 2 8° K4.03.170LZ Euro Style (169.9) (35.0) (50 x 20 Inv)
12.40 3.93 2 25° K4.03.315LZ Euro Style can be shortened to (314.9) (99.8) (50 x 20 Inv) 230mm C-C
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
5.90 0.67 1 8° 5.03.150 (149.8) (17.0)
10.13 2.36 2.00 x 16 1 20° 5.03.265LZ 5.3.108KX & 5.82.921 (257.3) (59.9) (50.8 x 16)
12.20 2.56 2.00 x 16 1 20° 5.03.310LZ 5.3.108KX & 5.82.661 (309.8) (65.0) (50.8 x 16)
13.38 2.75 2.00 x 16 1 30° 5.03.340LZ 5.3.288KX & 5.82.661 (339.8) (69.8) (50.8 x 16)
14.96 2.75 2.00 x 16 1 30° 5.03.380LZ 5.3.2261KX & 5.82.661 (379.9) (69.8) (50.8 x 16)
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
6.57 0.94 1 8° 6.03.167 (167.0) (24.0)
7.63 0.94 1 8° 6.03.194 (194.0) (24.0)
13.19 2.30 2.50 x 16 1 22° 6.03.335LZ 6.3.2671KX & 6.82.1171.10 (335.0) (60.0) (65.3 x 16)
13.97 3.94 2.50 x 16 1 22° 6.03.355LZ 6.3.2671KX & 6.82.1281 (355.0) (100.0) (63.5 x 16) 14.76 4.13 2.50 x 16 1 22° 6.03.375LZ 6.3.2671KX & 6.82.1281.1 (375.0) (105.0) (63.5 x 16) 16.34 4.92 2.50 x 16 1 45° 6.03.415LZ 6.3.2551KX & 6.82.1281.1 (415.0) (124.9) (63.5 x 16) I/Axle Shaft 17.05 5.31 2.50 x 16 1 45° 6.03.433LZ 6.3.2551KX & 6.82.1061.1 (433.0) (134.8) (63.5 x 16) I/Axle Shaft 18.11 5.31 2.50 x 16 1 45° 6.03.460LZ 6.3.2551KX & 6.82.1061.3 (459.9) (134.8) (63.5 x 16) I/Axle Shaft 19.13 5.31 2.50 x 16 1 45° 6.03.486LZ 6.3.2551KX & 6.82.1061.11 (485.9) (134.8) (63.5 x 16) I/Axle Shaft
SPICER CATALOGUE PAGE:- 28
SPICER
September
2014 © Driveline Services Australia Pty Ltd
YOKE SHAFT AND SLIP YOKE ASSEMBLIES – LESS JOINTS
C-C Spline Total Angle L Size Slip Type ° Part No. Notes / Suggestions
SERIES: SPL170 Suits U/J: SPL170X 55.00 x 164.00
17.40 5.90 170.03.443X Strap Kit 170.70.18X (442.8) (150.0)
19.00 7.09 170.03.482X Strap Kit 170.70.18X (482.8) (180.0)
YOKE SHAFT AND SLIP YOKE ASSEMBLIES – WITH JOINTS C-C Spline Total Angle L Size Slip Type ° Part No. Notes / Suggestions
SERIES: SPL170 Suits U/J: SPL170X 55.00 x 164.00
17.40 5.90 170.03.443 Strap Kit 170.70.18X (442.8) (150.0)
19.00 7.09 170.03.482 Strap Kit 170.70.18X (482.8) (180.0)
L
Compressed
SPICER CATALOGUE PAGE:- 29
SPICER
September
2014 © Driveline Services Australia Pty Ltd
UB – U’Bolt Type BS – Brg Strap Type CV –
END YOKES TO SUIT LIGHT DUTY VEHICLES & 4WD
Dia x Spline Hub C-EOS DTH Angle Yoke S O L L1 ° Type Part No. Application
SERIES: 1210 Suits U/J: 5.443X 26.99 x 61.93
1.146 x 26 Inv 1.625 3.375 1.156 15° CV 2.4.5891 SCV42 Pattern WHILE STOCKS LAST
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
1.125 x 10 1.550 3.000 1.500 13° CV 2.4.4061X Dana T.Case TC20
1.125 x 10 1.550 3.000 1.500 UB 2.4.2791
1.146 x 26 Inv 1.550 3.000 1.500 22° UB 2.4.8091X Dana Axle 30-44-50
1.146 x 26 Inv 1.550 3.000 1.500 13° CV 2.4.4341 Dana T.Case TC30
1.209 x 27 Inv 1.520 3.060 1.480 - BS 2.4.2007.1X GM 10 Bolt Diff
1.235 x 28 Inv 1.812 4.030 2.420 25° UB 2.4.FD01X Ford 9” Diff
1.235 x 28 Inv 1.812 5.000 2.420 UB 2.4.3104.06 LONG Ford 9” RUJ2039
1.250 x 10 2.000 3.280 1.750 30° UB 2.4.4471X IHC Navistar
1.276 x 29 Inv 1.875 2.940 1.500 18° UB 2.4.3801X Dana Axle 60-70
1.312 x 30 Inv 1.940 3.160 1.150 BS 2.4.GM03X GM 10 Bolt
1.328 x 30 Inv 1.740 2.590 1.190 BS 2.4.GM01X GM 12 Bolt
1.375 x 10 2.125 3.438 2.000 22° UB 2.4.1731 New Process G.Box 420-435 Warner G.Box T98 Spicer T.Case 23-24
1.401 x 32 Inv 1.940 3.440 2.000 US 2.4.JK01 JK Jeep Wrangler
1.401 x 32 Inv 2.125 3.440 2.000 22° UB 2.4.4191 New Process T.Case 203-205 In Put
1.401 x 32 Inv 1.875 3.880 2.000 13° CV 2.4.5341 New Process T.Case 203-205 In Put
SPICER CATALOGUE PAGE:- 30
SPICER
September
2014 © Driveline Services Australia Pty Ltd
UB – U’Bolt Type BS – Brg Strap Type CV –
END YOKES TO SUIT LIGHT DUTY VEHICLES & 4WD
Dia x Spline Hub C-EOS DTH Angle Yoke S O L L1 ° Type Part No. Application
SERIES: 1330 Suits U/J: RUJ3002 26.99 x 92.08
1.328 x 30 Inv 1.740 2.590 1.190 BS 2.4.GM02X GM 12 Bolt
1.401 x 32 Inv 1.875 3.880 2.000 13° CV 2.4.5441 New Process T.Case 203-205
SERIES: 1330 Suits U/J RUJ3000 28.58 x 92.08
1.235 x 28 Inv 1.812 4.030 2.420 UB 2.4.E6TZ Ford 9” Diff U’Bolt Part #105
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.235 x 28 Inv 1.812 4.000 2.420 - UB 3.4.3504.08 FORD 9” 5.178X
1.235 x 28 Inv 1.812 5.000 2.420 - UB 3.4.3504.08 LONG FORD 9” 5.178X
1.312 x 30 Inv 2.110 3.190 1.150 - BS 3.4.0880.1X GM Light Truck
1.401 x 32 Inv 2.125 3.500 2.000 22° UB 3.4.6211 New Process T.Case 203-205
1.590 x 30 Inv 2.370 3.750 1.630 - BS 3.4.0882.1X GM Light Truck
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
1.276 x 29 Inv 1.875 3.188 1.500 22° BS 3.4.5711.1X Dana Axle 60-61-70
1.590 x 30 Inv 2.370 3.750 1.630 - BS 3.4.0884.1X GM Light Truck
SPICER CATALOGUE PAGE:- 31
SPICER
September
2014 © Driveline Services Australia Pty Ltd
END YOKES TO SUIT EATON-FULLER ROADRANGER
TRANSMISSIONS
Yoke Part Number Dia x Spline W/- Slinger W/O Slinger Series Model Application
2.50 x 10 6.4.6921X 6.4.6611 1710 RT613-6613 RT910-915-9513
Seal 3.75 6.5.4.3551X 6.5.4.3451 1810 and various other models
2.75 x 10 6.4.5251X 6.4.4551 1710 RT12 & 14 Series Seal 3.50
2.75 x 10 6.4.6931X 6.4.6821 1710 14613-14615-14715-14
Seal 3.75 6.5.4.3561X 6.5.4.3491 1810 15615-15613
6.5.4.3561.1X 6.5.4.3491.1 1810HR 16718B-16609-16613-16618-18718B
and various other models
2.794 x 54 6.5.4.4631 1810 RT14-15-16-18-20 Series
6.5.4.4631.1 1810HR
END YOKES TO SUIT MACK GEARBOX
Yoke Part Number Dia x Spline W/- Slinger W/O Slinger Series Model Application
2.375 x 46 6.5.4.3251 1810 Transmission
Seal 3.50
SPICER CATALOGUE PAGE:- 32
SPICER
September
2014 © Driveline Services Australia Pty Ltd
END YOKES TO SUIT EATON / SPICER AXLES
Length Angle Part Number
Dia x Spline (Inch) ° W/- Slinger W/O Slinger Series Loc. Application
1.790 x 34 5.43 25° 6.4.6481 1710 F/O
Seal 2.625 6.31 45° 6.4.8521X 6.4.6451 1710 F/O
2.024 x 39 5.25 33° 6.4.6001X 6.4.5991 1710 F/I
Seal 2.625 6.15 45° 6.4.6021X 6.4.6021X 1710 R/I
5.25 30° 6.4.9041X 6.4.8441 1710 F/O
6.125 45° 6.4.9001.1X 6.4.8431.1 1710HR F/O
2.024 x 39 6.125 40° 6.4.8991.1X 6.4.8411.1 1710HR R/I
Seal 3.00 5.25 30° 6.4.9031.1X 6.4.8421.1 1710HR R/I
2.143 x 41 6.625 38° 6.4.7651X 6.4.7541 1710 F/O
Seal 2.938 6.13 42° 6.4.7561X 6.4.7551 1710 R/I
6.13 42° 6.4.9181X 6.4.7551 1710 R/I
2.144 x 32 6.25 45° 6.4.7171X 6.4.5791 1710 R/I Spicer J340-S J380-S Seal 3.00
2.149 x 16 5.188 25° 6.4.5061X 6.4.4961 1710 F/I Early Eaton DS.DP.DT 340
Seal 2.938 6.625 33° 6.4.5481X 6.4.4591 1710 F/O
6.625 33° 6.4.5481X 6.4.4591 1710 R/I
2.274 x 44 5.19 27° 6.4.6041X 6.4.6031 1710 F/I Late Eaton DS.DP.DT Seal 2.938 340-40-401-402-451
5.25 30° 6.5.4.3281X 6.5.4.4321 1810 F/I
5.25 30° 6.5.4.4351X 6.5.4.4321 1810 F/I
5.25 30° 6.5.4.4351.1X 6.5.4.4321.1 1810HR F/I
5.25 30° 6.5.4.3281.1X 6.5.4.4321.1 1810HR F/I
2.274 x 44 5.188 30° 6.4.8981.1X 6.4.8451.1 1710HR F/I Eaton 404-405-454
Seal 3.00 5.25 30° 6.5.4.4571.1X 6.5.4.4311.1 1810HR F/I
2.390 x 46 6.00 30° 6.5.4.3921x 6.5.4.3911 1810 F/I Eaton DS.DP 461-651
Seal 3.375 6.00 30° 6.5.4.3921.1X 6.5.4.3911.1X 1810HR F/I
2.422 x 18 5.81 26° 6.4.4751X 6.4.4581 1710 F/I Eaton 44D Seal 3.375 DP.DT 440-650
Front Input = F/I
Rear Input= R/I
Front Output
= F/O
SPICER CATALOGUE PAGE:- 33
SPICER
September
2014 © Driveline Services Australia Pty Ltd
Front Input = F/I
Rear Input= R/I
Front Output
= F/O
END YOKES TO SUIT ROCKWELL / MERITOR AXLES Length Angle Part Number Dia x Spline (Inch) ° W/- Slinger W/O Slinger Series Loc. Application
1.75 x 10 4.87 25° 6.4.2381 1710 F/O
Seal 2.75 4.87 25° 6.4.2381 1710 R/I
1.774 x 34 5.438 35° 5.4.5081X 5.4.6261 1610 F/O
Seal 2.50 4.87 22° 6.4.5131X 6.4.6331 1710 F/O SP40-SL.SQ100
5.97 45° 6.4.5111X 6.4.6321 1710 F/O SLHP-SQHP
4.87 22° 6.4.5131X 6.4.6331 1710 F/O RS120-230
5.97 45° 6.4.5111X 6.4.6321 1710 R/I SLHP-SQHP
1.969 x 10 5.25 21° 6.4.4361X 6.4.3221 1710 F/O SSHD Early
Seal 2.75 5.25 21° 6.4.4361X 6.4.3221 1710 R/I
2.00 x 10 5.188 25° 6.4.4741X 6.4.3241 1710 F/I SLHD-SQHD
Seal 2.938
2.024 x 39 5.25 33° 6.4.6951X 6.4.5521 1710 F/O SSHD Late
Seal 2.75 6.50 35° 6.4.6871X 6.4.5501 1710 F/O
5.25 33° 6.4.6951X 6.4.5521 1710 R/I
6.50 35° 6.4.6871X 6.4.5501 1710 R/I
2.024 x 39 6.25 43° 6.4.6381X 6.4.6371 1710 F/I SP40-SL.SQ100
Seal 3.00 5.15 33° 6.4.6411X 6.4.6401 1710 F/I SP40-SL.SQ100
6.25 43° 6.4.6381X 6.4.6371 1710 F/I
5.19 30° 6.5.4.3381X 6.5.4.3371 1810 F/I RT140
5.19 30° 6.5.4.3381.1X 6.5.4.3371.1 1810HR F/I
5.15 33° 6.4.6411X 6.4.6401 1710 F/O RT145-160-180-185-380
5.19 30° 6.5.4.3381X 6.5.4.3371 1810 F/O RT160-185
5.19 30° 6.5.4.3381.1X 6.5.4.3371.1 1810HR F/O
5.16 33° 6.4.6421X 6.4.6401 1710 R/I RS145-240-RS380
6.25 43° 6.4.6391X 6.4.6371 1710 R/I RT140-145-RT380
5.19 30° 6.5.4.3381X 6.5.4.3371 1810 R/I
2.25 x 10 6.06 24° 6.4.4411X 6.4.1991 1710 F/I SSHD Early
Seal 3.00
SPICER CATALOGUE PAGE:- 34
SPICER
September
2014 © Driveline Services Australia Pty Ltd
END YOKES TO SUIT ROCKWELL & MERITOR AXLES
Length Angle Part Number Dia x Spline (Inch) ° W/- Slinger W/O Slinger Series Loc. Application
2.375 x 46 5.39 29° 6.4.7181X 6.4.7161 1710 F/I R145-160
Seal 3.25 5.69 22° 6.4.5461X 6.4.5451 1710 F/I SSHD Late
6.50 45° 6.4.7771X 6.4.7761 1710 F/I
6.50 45° 6.4.7771.1X 6.4.7761.1 1710HR F/I
5.16 30° 6.5.4.3731X 6.5.4.3721 1810 F/I
5.16 30° 6.5.4.3731.1X 6.5.4.3721.1 1810HR F/I
5.44 30° 6.5.4.2711X 6.5.4.2701 1810 F/I
5.44 30° 6.5.4.2711.1X 6.5.4.2701.1 1810HR F/I
5.69 30° 6.5.4.3221 6.5.4.3201 1810 F/I RT180-185-380
5.39 29° 6.4.7181X 6.4.7161 1710 R/I RS:RT160
6.50 45° 6.4.7771X 6.4.7761 1710 R/I
5.16 30° 6.5.4.3731X 6.5.4.3721 1810 R/I
5.16 30° 6.5.4.3731.1X 6.5.4.3721.1 1810HR R/I
5.69 30° 6.5.4.3221X 6.5.4.3201 1810 R/I RS:RT180-185
Front Input = F/I
Rear Input= R/I
Front Output
= F/O
END YOKES TO SUIT MACK AXLES
Length Angle Part Number
Dia x Spline (Inch) ° W/- Slinger W/O Slinger Series Loc. Application
2.024 x 39 5.188 30° 6.5.4.3261 1810 F/O
6.5.4.3261 1810 R/I
2.375 x 46 5.406 30° 6.5.4.3251 1810 F/I 34,000-80,000 LB Axles Seal 3.5
Front Input = F/I
Rear Input= R/I
Front Output
= F/O
SPICER CATALOGUE PAGE:- 35
SPICER
September
2014 © Driveline Services Australia Pty Ltd
MIDSHIP END YOKES
Spline C-EOS DTH S L L1 Type Part No. Notes / Suggestions
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76 1.375 x 10 3.219 1.750 2 - BS 2.4.2671.1 2.57.1441 (2.5x.065)
1.375 x 10 2.480 1.18 1 - SR 2.4.0901 2.57.0901 (63.0) (30.0)
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.375 x 10 3.281 1.871 2 - BS 3.4.178.1X 3.54.611 (3x.083)
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
1.500 x 10 3.719 2.000 2 - UB 3.4.6561 3.57.2641 (3x.095) 3.57.2651 (3.5x.095)
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
1.500 x 10 4.031 2.000 2 - BS 3.4.3091.1 3.57.2641 (3x.095) 3.57.2651 (3.5x.095)
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
1.500 x 10 3.775 2.000 2 - UB 4.4.2051 3.57.2641 (3x.095) 3.57.2651 (3.5x.095)
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
1.750 x 10 4.125 2.250 1 5.4.1721 5.53.141 (3.5x.134)
SERIES: 1610HR Suits U/J: 5.674X 47.63 x 134.94
1.750 x 10 4.125 2.250 2 - BS 5.4.1721.1 5.53.141 (3.5x.134)
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
1.960 x 10 5.000 3.000 1 6.4.1981 6.53.201 (4.09x.180)
1.968 x 38 5.000 3.000 1 6.4.7141 Stub 6.53.411 (4.09x.180)
2.344 x 16 4.938 2.750 1 6.4.4601 Stub 6.53.311 (4.09x.180)
SPICER CATALOGUE PAGE:- 36
SPICER
September
2014 © Driveline Services Australia Pty Ltd
MIDSHIP END YOKES
Spline C-EOS DTH S L L1 Type Part No. Notes / Suggestions
SERIES: 1710HR Suits U/J: 5.675X 49.21 x 154.78
1.960 x 10 5.000 3.000 1 6.4.1981.1 6.53.201 (4x.134)
1.968 x 38 5.000 3.000 2 - BS 6.4.7141.1 6.53.411 (4.09x.180)
2.344 x 16 4.938 2.750 2 - BS 6.4.4601.1 6.53.311 (4.09x.180)
2.390 x 46 4.938 2.750 2 – BS 6.4.7481.1 6.3.53.21 (4.09x.180)
SERIES: 1760 Suits U/J: 5.407X 49.21 x 177.80
2.344 x 16 5.500 2.750 1 6.3.4.161 6.53.311 (4.09x.180)
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.69
2.344 x 16 5.500 2.750 1 6.5.4.1891 6.5.53.91 (4.59x.180)
SERIES: 1810HR Suits U/J: 5.676X 49.21 x 191.69
2.344 x 16 5.500 2.750 2 - BS 6.5.4.1891.1 6.5.53.91 (4.59x.180)
2.390 x 46 5.500 2.750 2 - BS 6.5.4.3591.1 6.5.53.171 (4.59x.180)
SERIES: SPL250 Suits U/J: SPL250X 60.00 x 163.00
2.390 x 46 5.750 2.750 2 - BS 250.4.21.1 250.53.11 (132x6)
SERIES: RPL250 Suits U/J: CP25RPLS 52.33 x 208.28 2.390 x 46 4.900 2.750 2 25RP-44001 6.5-53-171
SPICER CATALOGUE PAGE:- 37
SPICER
September
2014 © Driveline Services Australia Pty Ltd
UB – U.Bolt
TYPE 2 TYPE 1 BS – Bearing Strap SR – Snap Ring
P.T.O. END YOKES – BORED & KEYED Bore X Keyway C-End Hub S L L1 O Type Part No. Notes / Suggestions
SERIES: 1140
None None 3.15 1.81 2.04 1 SR K1.4.007 - - (80.00) (46.0) (52.0)
SERIES: 1310
None None 2.56 1.50 2.11 1 SR 2.4.177B - - (65.0) (38.1) (53.6)
0.875 0.250 2.56 1.50 2.11 1 SR 2.4.583 (22.23) (6.35) (65.0) (38.1) (53.6)
1.000 0.312 2.56 1.50 2.00 1 SR 2.4.473 (25.40) (7.92) (65.0) (38.1) (50.8)
1.125 0.250 2.56 1.50 2.11 1 SR 2.4.503 (28.57) (6.35) (65.0) (38.1) (53.6)
1.125 0.312 2.56 1.50 2.11 1 SR 2.4.523 (28.57) (7.92) (65.0) (38.1) (53.6)
1.250 0.312 2.56 1.50 2.11 1 SR 2.4.533 (31.75) (7.92) (65.0) (38.1) (53.6)
1.250 0.312 2.97 1.50 2.12 2 UB 2.4.783 (31.75) (7.92) (75.5) (38.1) (53.8)
1.375 0.375 2.56 1.50 2.00 1 SR 2.4.803 (34.92) (9.52) (65.0) (38.1) (50.8)
1.500 0.375 2.56 1.50 2.11 1 SR 2.4.1233 (38.10) (9.52) (65.0) (38.1) (53.6)
SERIES: 1350
1.250 0.312 2.97 1.50 2.25 2 UB 3.4.283 (31.75) (7.92) (75.5) (38.1) (57.1)
SERIES: 1410
1.250 0.312 3.68 2.07 2.25 2 UB 3.4.343 (31.75) (7.92) (93.5) (52.8) (57.1)
SPICER CATALOGUE PAGE:- 38
SPICER
September
2014 © Driveline Services Australia Pty Ltd
TYPE 1 TYPE 3
P.T.O. END YOKES – SPLINED
Spline C-END Hub S L L1 O Type Part No. Notes
SERIES: 1310
.875 x 13 Inv 2.56 1.57 2.00 1 - SR 2.4.3331 (22.22 x 13) (65.1) (39.8) (50.8)
.875 x 13 Inv 4.32 1.50 3 - SR 2.4.13103 Clamplock Type (22.22 x 13) (109.8) (38.1)
1.000 x 15 Inv 2.31 1.06 2.12 1 - SR 2.4.4921 (25.4 x 15) (58.7) (27.0) (54.0)
1.000 x 15 Inv 3.25 1.50 3 - SR 2.4.13104 Clamplock Type (25.4 x 15) (82.5) (38.1)
1.250 x 14 Inv 2.56 1.50 2.12 1 - SR 2.4.1741 (31.75 x 14) (65.1) (38.1) (54.0)
1.250 x 14 Inv 3.25 1.50 3 - SR 2.4.13106 Clamplock Type (31.75 x 14) (82.5) (38.1)
1.375 x 21 Inv 4.32 1.50 3 - SR 2.4.13107 Clamplock Type (34.92 x 21) (109.8) (38.1)
1.500 x 17 Inv 4.32 1.50 3 - SR 2.4.13132 Clamplock Type (38.1 x 17) (109.8) (38.1)
SERIES: 1350
1.375 x 21 Inv 3.60 1.50 3 - SR 3.4.13507 Clamplock Type (34.92 x 21) (91.5) (38.1)
1.500 x 23 Inv 4.41 1.50 3 - SR 3.4.13543 Clamplock Type (38.10 x 23) (112.2) (38.1)
SPICER CATALOGUE PAGE:- 39
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELD YOKES Tube Butt W-C Angle Size B L ° Part No. Notes / Suggestions
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
2.00 x .065 1.88 1.38 17° K1.26.GB17 Solid butt (50.8 x 1.65) (47.8) (35.1)
2.00 x .095 1.82 1.50 17° K1.26.GB17A (50.8 x 1.65) (46.1) (38.1) WHILE STOCKS LAST
2.50 x .065 2.38 1.36 17° K1.26.GB67 (63.5 x 1.65) (60.5) (34.5)
2.75 x .065 2.63 1.29 17° K1.26.GB137 (69.85 x 1.65) (66.8) (32.8)
3.00 x .065 2.87 1.44 17° K1.26.GB717 (76.2 x 1.65) (73.1) (36.5) WHILE STOCKS LAST
SERIES: 1210 Suits U/J: 5.443X 26.99 x 61.93
2.00 x .083 1.84 1.50 20° 2.28.2417 (50.8 x 2.11) (46.7) (38.1)
2.50 x .065 2.37 1.50 20° 2.28.1947 (63.5 x 1.65) (60.3) (38.1)
2.75 x .065 2.63 1.53 20° 2.28.1947.1 (69.85 x 1.65) (66.8) (39.0)
SERIES: 1300 Suits U/J: K5L4R 26.99 x 74.61
2.50 x .065 2.37 1.73 20° K2.26.GB1517 Can use 687.15 (63.5 x 1.65) (60.2) (44.0)
2.00 x .095 1.81 1.75 20° K2.26.GB17 Can use 687.15 (50.8 x 2.41) (46.0) (44.5)
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
2.00 x .083 1.84 1.69 22° 2.28.357 (50.8 x 2.11) (46.7) (42.9)
2.00 x .095 1.81 1.69 22° 2.28.577 (50.8 x 2.41) (46.0) (42.9)
2.50 x .065 2.39 1.85 30° 2.28.277 (63.5 x 1.65) (60.6) (47.0)
2.50 x .083 2.34 1.84 30° 2.28.367 (63.5 x 2.11) (59.5) (46.7)
2.50 x .095 2.31 1.85 30° 2.28.2700 (63.5 x 2.41) (58.9) (47.0)
SPICER CATALOGUE PAGE:- 40
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELD YOKES
Tube Butt W-C Angle Size B L ° Part No. Notes / Suggestions
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
2.75 x .065 2.63 2.44 30° 2.28.307 (69.8 x 1.65) (66.8) (62.0)
2.75 x .083 2.59 1.69 21° 2.28.1617 (69.8 x 2.11) (65.8) (42.9)
3.00 x .065 2.88 1.69 21° 2.28.327 (76.2 x 1.65 ) (73.2) (42.9)
3.00 x .083 2.84 1.69 21° 2.28.437 (76.2 x 2.11) (72.1) (42.9) 3.25 x .065 3.128 1.69 21 2.28.557 (82.5 x1.65) (79.5) (43)
3.50 x .065 3.38 1.69 21° 2.28.397 (88.9 x 1.65) (85.9) (42.9)
SERIES: 3R Suits U/J: 114.3105 28.58 x 65.10 (INTERNAL)
2.75 x .065 2.63 2.24 3R.28.307 (69.9 x 1.65) (66.8) (57.0)
3.00 x .065 2.88 2.24 3R.28.327 (76.2 x 1.65) (73.1) (46.8)
3.50 x .065 3.37 2.24 3R.28.397 (88.99 x 1.65) (85.7) (46.8)
SERIES: 1330 Suits U/J: RUJ3002 26.99 x 92.08
2.50 x .083 2.34 1.72 25° 2.28.1707 (63.5 x 2.11) (59.5) (43.7)
3.00 x .065 2.88 1.72 25° 2.28.1177 (76.2 x 1.65) (73.2) (43.7)
3.00 x .083 2.84 1.72 25° 2.28.1697 (76.2 x 2.11) (72.1) (43.7)
3.50 x .065 3.38 1.81 25° 2.28.1977 (88.9 x 1.65) (85.9) (46.0)
3.50 x .083 3.34 1.81 20° 2.28.1717 (88.9 x 2.11) (84.8) (46.0)
SPICER CATALOGUE PAGE:- 41
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELD YOKES
Tube Butt W-C Angle Size B L ° Part No. Notes / Suggestions
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
- 2.30 2.26 20° 3.58.58 * C-End solid butt – not machined for tube (58.6) (57.5) Can be used as bored end yoke. 2.50 x .083 2.34 1.94 20° 3.28.47 (63.5 x 2.11) (59.5) (49.3)
3.00 x .083 2.84 2.00 20° 3.28.57 (76.2 x 2.11) (72.1) (50.8)
3.00 x .083 2.88 2.12 3.28.39017 Performance component (76.2 x 2.11) (72.1) (54.0)
3.50 x .065 3.38 1.81 20° 3.28.257 (88.9 x 1.65) (58.9) (36.5)
2.50 x .095 2.32 1.44 3.28.3281X Double cardan pin yoke (63.5 x 2.41) (58.9) (36.5)
2.75 x .083 2.52 1.81 3.28.1747.1X Double cardan pin yoke (69.9 x 2.11) (64.0) (46.0)
3.00 x .083 2.76 1.81 3.28.1327.1X Double cardan pin yoke (76.2 x 2.11) (70.0) (46.0)
SERIES: 1410 Suits U/J: K5GB10R 30.16 x 106.35
- 2.30 2.36 20° 3.28.017 * C-End solid butt – not machined for tube (58.6) (60.0) Can be used as bored end yoke.
2.00 x .109 1.79 2.05 20° 3.28.657 (50.8 x 2.77) (45.5) (52.0)
3.00 x .083 2.84 2.13 30° 3.28.97 (76.2 x 2.11) (72.2) (54.1)
3.00 x .095 2.82 2.13 30° 3.28.267 (76.2 x 2.41) (71.6) (54.1) 3.50 x .065 2.52 2.13 3.28.367 (88.9 x 1.65) (58.9) (54.0)
3.50 x .083 3.34 2.13 30° 3.28.557 (88.9 x 2.11) (84.9) (54.1)
3.50 x .095 3.31 2.13 20° 3.28.1637 (88.9 x 2.41) (84.3) (54.1)
4.00 x .083 3.84 1.88 22° 3.28.457 (101.6 x 2.11) (97.5) (47.8) WHILE STOCKS LAST
4.50 x .095 4.31 2.03 22° 3.28.577 (114.3 x 2.41) (109.5) (51.6) WHILE STOCKS LAST
SPICER CATALOGUE PAGE:- 42
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELD YOKES
Tube Butt W-C Angle Size B L ° Part No. Notes / Suggestions
SERIES: 1480 Suits U/J: 5.188X 34.93 x 106.38
3.50 x .083 3.34 2.03 22° 3.28.537 (88.9 x 2.11) (84.8) (51.6)
3.50 x .095 3.32 2.03 22° 687.30.26 (88.9 x 2.41) (84.3) (51.6)
4.00 x .083 3.84 2.03 22° 3.28.507 (101.6 x 2.11) (97.5) (51.6) WHILE STOCKS LAST 4.50 x .095 4.31 2.03 22° 3.28.517 (114.3 x 2.41) (109.5) (51.6) WHILE STOCKS LAST
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
3.50 x .095 3.31 2.69 35° 4.28.417 (88.9x 2.41) (84.1) (68.3)
3.50 x .095 3.31 2.19 22° 4.28.307 (88.9 x 2.41) (84.1) (55.6) 4.00 x .083 3.87 2.19 22° 4.28.277 (101.6 x 2.11) (98.3) (55.6) WHILE STOCKS LAST
SERIES: 1510 Suits U/J: K5GB22R 39.70 x 115.90
3.00 x .095 2.81 2.75 K4.26.GB477 (76.2x 2.41) (71.4) (69.9)
3.50 x .095 3.31 2.83 K4.26.GB547 (88.9 x 2.41) (84.1) (71.9)
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
3.50 x .134 3.25 3.00 35° 5.28.627 (88.9 x 3.40 (82.6) (76.2)
4.09 x .180 3.75 3.00 5.28.327 (103.9 x 4.57) (95.3) (76.2)
4.50 x .095 4.31 3.93 5.28.617X (114.3 x 2.41) (109.5) (100.0) WHILE STOCKS LAST Fitted with collar to suit tube
SERIES: 1650 Suits U/J: 5.165X 41.28 x 142.00
3.50 x .134 3.24 5.28.627 (88.9 x 3.40) (82.3)
SPICER CATALOGUE PAGE:- 43
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELD YOKES
Tube Butt W-C Angle Size B L ° Part No. Notes / Suggestions
SERIES: 1710 Suits U/J: 5.407X 49.21 x 154.78
4.09 x .180 3.75 3.03 22° 6.28.347 (103.9x 4.57) (95.3) (77.0)
4.09 x .180 3.75 3.69 45° 6.28.467 (103.9 x 4.57) (95.3) (93.7) 4.59 x .180 4.25 3.03 22° 6.28.407 (116.58 x 4.57) (108.0) (77.0)
SERIES: 1760 Suits U/J: 5.407X 49.21 x 177.80
4.09 x .180 3.75 3.03 30° 6.3.28.17 (103.9x 4.57) (95.3) (77.0)
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.69
3.55 x .207 3.15 3.38 30° 6.5.28.137 (90.1x 5.26) (80.0) (85.9)
4.59 x .180 4.25 3.38 30° 6.5.28.117 (116.5 x 4.57) (107.7) (85.9) 4.50 x .259 4.00 3.38 30° 6.5.28.127 (114.3 x 6.58) (101.6) (85.9)
SERIES: RPL25 Suits U/J: CP25RPLS 53.25 x 208.28
4.59 x .180 4.25 3.70 24° 25RP.28.001 (116.58 x 4.57) (108.0) (94.0)
SERIES: SPL170 Suits U/J: SPL170X 55.00 x 164.00
- 4.34 4.72 45° 170.28.27 Machine butt to suit 120x6 tube (120.0x 5.00) (110.3) (120.0)
- 4.73 3.70 170.28.17 Machine butt to suit 130x6 tube (130.0 x 5.00) (120.3) (94.0)
SERIES: 1850 Suits U/J: 5.185X 55.55 x 205.59
4.50 x .259 3.98 4.00 22° 8.28.17 (114.3 x 6.58) (101.1) (101.6)
SERIES: 1880 Suits U/J: 5.308X 55.55 x 205.59
4.50 x .259 4.00 4.00 22° 8.28.147 (114.3 x 6.58) (101.6) (101.6) WHILE STOCKS LAST
SERIES: SPL250 Suits U/J: SPL250X 60.00 x 163.00
- 4.73 4.09 250.28.17 Machine butt to suit 130x6 tube (132.0 x 6.00) (120.3) (104.0)
SPICER CATALOGUE PAGE:- 44
SPICER
September
2014 © Driveline Services Australia Pty Ltd
STUB SHAFTS
Tube Butt W-EOS Size B L L2 Type Part No. Notes / Suggestions
SPLINE: 1.060 x 16 (26.92 x 16)
2.000 x .065 1.88 4.09 1.75 1 K1.42.GB1901 K1.3.A360 (50.8 x 1.65) (47.8) (103.9) (44.5)
2.500 x .065 2.38 4.19 1.75 1 K1.42.GB1921 K1.3.A360 (63.5 x 1.65) (60.3) (106.4) (44.5)
- - - 11.81 - 1.42.300 Full length splined bar (300.0)
SPLINE: 1.250 x 16 (31.75 x 16)
1.205 x .120 1.03 6.13 2.00 1 2.40.1771 2.3.4441KX (31.75 x 3.05) (26.2) (155.7) (50.8)
1.750 x .065 1.63 4.49 - 1 2.40.971 10.3.121KX (44.45 X 1.65) (41.3) (114.0)
2.000 x .083 1.84 6.00 2.00 1 2.40.1741 2.3.8861KX (50.8 x 2.11) (46.7) (152.4) (50.8)
2.500 x .065 2.38 7.75 2.50 1 2.40.2301 2.3.8961KX (63.5 x 1.65) (60.4) (196.9) (63.5)
SPLINE: 1.375 x 16 (34.95 x 16)
2.000 x .083 1.84 5.19 2.25 1 2.40.1031 2.3.128KX (50.8 x 2.11) (46.7) (131.8) (57.2)
2.000 x .083 1.85 6.19 2.25 1 2.40.2451 2.3.5221KX (50.8 x 2.11) (46.9) (157.2) (57.2)
2.000 x .095 1.82 7.75 2.00 1 2.40.3081 2.3.5821KX (50.8 x 2.41) (46.3) (196.9) (50.8)
2.000 x .095 1.82 5.08 1.75 1 2.40.2701 2.3.128KX (50.8 x 2.41) (46.3) (129.0) (44.5)
2.500 x .065 2.38 5.08 2.00 1 2.40.2721 2.3.128KX (63.5 x 1.65) (60.4) (129.0) (50.8) WHILE STOCKS LAST Replacing with 2.40.1041
2.500 x .065 2.38 5.35 2.25 1 2.40.1041 2.3.128KX (63.5 x 1.65) (60.4) (136.0) (57.2)
2.500 x .083 2.34 5.34 2.25 1 2.40.1131 Use 2.40.1041 & machine butt (63.5 x 2.11) (59.4) (135.6) (57.2)
2.500 x .083 2.34 6.34 2.25 1 2.40.1711 2.3.5221KX (63.5 x 2.11) (59.4) (161.0) (57.2)
2.500 x .083 2.34 7.53 2.25 1 2.40.1851 2.3.5821KX (63.5 x 2.11) (59.4) (191.3) (57.2)
2.500 x .095 2.31 5.35 2.25 2.40.2891 2.3.128KX (63.5 x 2.41) (58.9) (136.0) (57.2)
SPICER CATALOGUE PAGE:- 45
SPICER
September
2014 © Driveline Services Australia Pty Ltd
STUB SHAFTS
Tube Butt W-EOS Size B L L2 Type Part No. Notes / Suggestions
SPLINE: 1.375 x 16 (34.95 x 16) Cont.
3.000 x .065 2.88 6.44 2.25 1 2.40.1221 2.3.5221KX (76.2 x 1.65) (73.2) (163.6) (57.2)
3.000 x .065 2.88 7.63 2.25 1 2.40.2051 2.3.5821KX (76.2 x 1.65) (73.2) (193.8) (57.2)
3.000 x .083 2.84 6.46 2.25 1 2.40.1521 2.3.5221KX (76.2 x 2.11) (72.1) (164.0) (57.2)
3.000 x .083 2.84 8.64 6.78 2 2.40.1871 2.3.5821KX (Change dust cap) (76.2 x 2.11) (72.1) (219.5) (172.2)
3.500 x .065 3.38 6.56 2.25 1 2.40.1231 2.3.7961KX (1330) (88.9 x 1.65) (85.9) (166.6) (57.2)
- - - 11.81 - 2.42.300 Full length splined bar (300.0)
SPLINE: 1.50 x 16 (38.10 x 16)
2.000 x .109 1.79 6.97 1 3.40.3101 (50.0 x 2.77) (45.7) (177) (80.0)
2.500 x .083 2.34 5.56 2.50 1 3.40.1471 3.3.598KX (63.5 x 2.11) (59.4) (141.2) (63.5)
3.000 x .065 2.88 5.71 2.50 1 3.40.3700 (76.2 x 1.65) (73.1) (145.0) (63.5) WHILE STOCKS LAST
3.000 x .083 2.84 5.94 2.50 1 3.40.1101 Use 3.40.3901 (76.2 x 2.11) (72.1) (150.9) (63.5) 3.000 x .083 2.84 6.5 3.40.1511 3.40.1511 WHILE STOCKS LAST
3.000 x .083 2.84 7.25 2.50 1 3.40.1611 Use 3.40.3891 (76.2 x 2.11) (72.1) (184.2) (63.5)
3.000 x .095 2.82 6.14 2.56 1 3.40.3901 Can replace 3.40.1101 (76.2 x 2.41) (71.6) (156.0) (65.0) Use 3.28.267
3.000 x .095 2.82 7.20 2.95 1 3.40.3891 3.3.488KX Can replace 3.40.1421 (76.2 x 2.41) (71.6) (183.0) (75.0)
3.000 x .095 2.82 13.78 2.95 1 3.40.350 Special for cross member clearance for (76.2 x 2.41) (71.6) (350.0) (75.0) PTO drive
3.500 x .083 3.34 7.53 3.00 1 3.40.1491 3.3.508KX / 3.3.488KX (88.9 x 2.11) (84.8) (191.3) (76.2)
3.500 x .095 3.29 6.14 2.56 1 3.40.4201 (88.9 x 2.41) (83.6) (156) (65.0) WHILE STOCKS LAST
- - - 11.81 - 3.42.300 Full length spline bar (300.0)
SPICER CATALOGUE PAGE:- 46
SPICER
September
2014 © Driveline Services Australia Pty Ltd
STUB SHAFTS
Tube Butt W-EOS Size B L L2 Type Part No. Notes / Suggestions
SPLINE: 1.56 x 16 (39.62 x 16)
3.500 x .083 3.34 6.75 3.00 1 3.40.1571 3.3.1601KX (88.9 x 2.11) (84.8) (171.5) (76.2)
3.500 x .083 3.34 8.75 3.00 1 3.40.1391 3.3.1641KX (88.9 x 2.11) (84.8) (222.3) (76.2)
3.500 x .083 3.34 10.75 3.00 1 3.40.1411 3.3.1661KX (88.9 x 2.11) (84.8) (273.1) (76.2)
SPLINE: 1.75 x 16 (44.45 x 16)
- 1.38 6.63 4.65 1 K4.42.002 Suitable for yoke shafts (35.05) (168.4) (118.1)
3.000 x .095 2.82 6.57 1 K4.42.GB1791 (76.2 x 2.41) (167) (166.8)
3.500 x .095 3.32 6.49 2.67 4.40.1801 (88.9 x 2.41) (84.3) (165) (68.0) WHILE STOCKS LAST
3.500 x .095 3.32 6.77 3.00 1 4.40.761 4.3.1241KX (88.9 x 2.41) (84.3) (172.0) (76.2)
3.500 x .095 3.32 9.22 3.00 1 4.40.721 4.3.1431KX (88.9 x 2.41) (84.3) (234.2) (76.2)
4.500 x .095 4.32 7.08 3.00 1 4.40.491 (114.3 x 2.41) (109.7) (179.8) (76.2) WHILE STOCKS LAST
- - - 11.81 - 4.42.300 Full length splined bar (300.0)
SPLINE: 2.00 x 16 (50.80 x 16)
3.000 x .095 2.82 8.75 3.00 1 6C.40.604 (76.2 x 2.41) (71.6) (223.0) (76.2)
3.500 x .095 3.31 7.56 3.50 1 5.40.451S Steel Spline Stub (88.9 x 2.41) (84.1) (192.1) (88.9)
3.500 x .134 3.24 9.69 3.50 1 5.40.1011 5.3.2261KX (88.9 x 3.40) (82.3) (246.1) (88.9)
3.500 x .134 3.24 10.19 3.50 1 5.40.1041 5.3.2141KX (88.9 x 3.40) (82.3) (258.8) (88.9)
3.500 x .134 3.24 8.78 3.50 1 7C.40.703 5.3.288KX (88.9 x 3.40) (82.3) (223.0) (88.9)
- - - 11.81 - 5.42.300 Full length splined bar (300.0)
SPICER CATALOGUE PAGE:- 47
SPICER
September
2014 © Driveline Services Australia Pty Ltd
STUB SHAFTS
Tube Butt W-EOS Size B L L2 Type Part No. Notes / Suggestions
SPLINE: 2.50 x 10 (63.50 x 10)
4.09 x .180 3.75 9.50 4.00 1 6.40.311 6.3.1461KX (103.9 x 4.57) (95.3) (241.3) (101.6) WHILE STOCKS LAST
3.500 x .120 3.27 8.27 4.00 1 6.42.301 Steel Spline Stub (88.9 x 3.04) (83.0) (210.0) (101.6) WHILE STOCKS LAST
SPLINE: 2.50 x 16 (63.50 x 16)
90 x 4.5 83.0 276.10 244.6 2 6.40.560 Steel Spline Stub
4.09 x .180 3.75 9.25 4.00 1 6.40.541 6.3.2671KX (103.9 x 4.57) (95.3) (235.0) (101.6)
4.09 x .180 3.75 10.56 4.00 1 6.40.521 6.3.2651KX (103.9 x 4.57) (95.3) (268.2) (101.6)
4.59 x .180 4.25 9.50 4.00 1 6.40.631 6.3.2671KX (116.58 x 4.57) (108.0) (241.3) (101.6)
4.59 x .180 4.25 10.66 4.00 1 6.40.621 6.3.2651KX (116.58 x 4.57) (108.0) (270.8) (101.6)
- - - 11.81 - 6.42.300 Full length splined bar (300.0)
SPLINE: 3.00 x 16 (76.20 x 16)
4.59 x .180 4.25 9.47 4.50 1 6.5.40.201 6.5.3.1351KX (116.58 x 4.57) (108.0) (240.5) (114.3)
4.59 x .180 4.25 11.25 4.50 1 6.5.40.191 6.5.3.1371KX (116.58 x 4.57) (108.0) (285.8) (114.3)
4.500 x .259 4.00 11.53 4.50 1 8.40.101 Use 6.5-40-191 Machine butt (114.3 x 6.58) (101.6) (292.9) (114.3)
SPICER CATALOGUE PAGE:- 48
SPICER
September
2014 © Driveline Services Australia Pty Ltd
MIDSHIP STUBS
Tube Butt W-EOS Brg Ø Thread Size B L L2 L3 P J Type Part No. Notes / Suggestions
SPLINE: 1.000 x 23 Inv (25.4 x 23 Inv)
2.50 x .065 2.38 3.43 2.25 1.18 M10x1 2 K2.57.1300 Ford Transit K2.4.1300 (63.5 x 1.65) (60.4) (87.3) (57.3) (30.0) Use Retainer, Washer & Bolt : K2.72.1300 / K2.72.1300A / K2.73.1300
SPLINE: 1.109 x 25 (28.16 x 25)
3.00 x .065 2.87 4.38 2.29 1.18 M10x1 2 2.57.0902 Ford Transit 687.20.4.025 CB58 (76.2 x 1.65) (73.1) (111.3) (58.3) (30.0) Use Retainer, Washer & Bolt : K2.72.1300 / K2.72.1300A / K2.73.1300
SPLINE: 1.375 x 10 (34.93 x 10)
2.50 x .065 2.38 3.60 2.34 1.38 .750x20 3 2.57.1441 2.1.2831 2.4.2671 (63.5 x 1.65) (60.4) (91.5) (59.5) (35.0) Use Pin, Washer & Nut : 2.72.001 / 2.73.001 / 2.74.001
3.00 x .065 2.87 3.00 1.77 1.77 M10x1 2 2.57.0901 Ford Transit 2.4.0901 CB59 (76.2 x 1.65) (73.1) (76.2) (45.0) (45.0) Use Retainer, Washer & Bolt : K2.72.1300 / K2.72.1300A / K2.73.1300
3.00 x .083 2.84 4.00 1.69 2.65 1.38 1x20 3 3.54.611 2.4.2671 (1310) (76.2 x 2.11) (72.2) (101.6) (42.9) (67.3) (35.0) 3.4.178.1X (1350)
SPLINE: 1.375 x 16 (34.93 x 16)
2.00 x .083 1.84 8.00 5.41 6.95 1.38 - 1 2.53.511 2.3.5221KX with 28.0195 dust cap (50.8 x 2.11) (46.7) (203.2) (137.4) (176.6) (35.0)
2.50 x .083 2.34 8.09 5.00 6.75 1.38 - 1 3.53.1351 3.3.1501KX (63.5 x 2.11) (59.4) (205.6) (127.0) (171.4) (35.0)
3.00 x .083 2.84 8.00 5.41 6.95 1.38 - 1 2.53.501 2.3.5221KX with 28.0195 dust cap (76.2 x 2.11) (72.2) (203.2) (137.4) (176.6) (35.0)
3.00 x .083 2.84 7.03 4.44 5.96 1.38 - 1 3.53.1371 (76.2 x 2.11) (72.2) (178.6) (112.8) (151.5) (35.0) WHILE STOCKS LAST
SPLINE: 1.500 x 10 (38.10 x 10)
3.00 x .095 2.82 4.13 1.99 2.97 1.58 1x20 3 3.57.2641 3.1.6221 (1410) (76.2 x 2.41) (71.6) (105.5) (50.5) (75.5) (40.0) K4.1.A2191 (1480-1510)
3.50 x .095 3.31 4.07 1.99 2.97 1.58 1x20 3 3.57.2651 3.1.6221 (1410) (88.9 x 2.41) (84.2) (103.5) (50.5) (75.5) (40.0) K4.1.A2191 (1480-1510)
SPLINE: 1.500 x 16 (38.10 x 16)
3.00 x .083 2.84 7.06 4.44 5.93 1.57 - 1 3.53.1031 3.3.2041KX (76.2 x 2.11) (72.1) (179.3) (112.8) (150.7) (40.0)
L
L2L3
P BSJ
L
L2
S
L3
P B
L
L2
S
L3
P BJ
SPICER CATALOGUE PAGE:- 49
SPICER
September
2014 © Driveline Services Australia Pty Ltd
MIDSHIP STUBS
Tube Butt W-EOS Size B L L2 L3 P J Type Part No. Notes / Suggestions
SPLINE: 1.560 x 16 (39.62 x 16)
3.50 x .083 3.34 8.55 5.94 7.49 1.57 - 1 3.53.451 3.3.1601KX with D3J dust cap (88.9 x 2.11) (84.9) (217.0) (150.9) (190.3) (40.0)
SPLINE: 1.750 x 10 (44.45 x 10)
3.50 x .134 3.25 4.34 2.06 1.19 1.77 1.25x18 3 5.53.141 K5.1.A0741 / 5.4.1721 (88.9 x 3.40) (82.6) (110.2) (52.3) (30.2) (45.0)
SPLINE: 1.750 x 16 (44.45 x 16)
3.50 x.095 3.32 8.56 5.94 7.47 1.77 - 1 4.53.61 4.3.1241KX with D4K dust cap (88.9 x 2.41) (84.3) (217.4) (150.9) (190.0) (45.0)
SPLINE: 1.781 x 34 (45.24 x 34)
3.50 x .134 3.25 5.40 2.06 1.17 1.77 1.25x18 3 5.53.261 (88.9 x 3.40) (82.6) (137.2) (52.32) (29.7) (45.0)
SPLINE: 1.950 x 10 (49.53 x 10)
3.50 x .156 3.19 5.16 2.88 1.18 1.97 1.25x18 3 6.53.151 6.4.1981 (88.9 x 3.96) (81.0) (131.1) (73.2) (30.0) (50.0) 231502 nut
4.09 x .180 3.75 5.16 2.88 1.18 1.97 1.25x18 3 6.53.201 6.4.1981 (103.9 x 4.57) (95.3) (131.1) (73.2) (30.0) (50.0) 231502 nut
SPLINE: 2.000 x 38 (50.80 x 38)
4.09 x .180 3.74 6.24 2.77 1.32 1.97 1.25x18 3 6.53.411 (103.9 x 4.57) (95.0) (158.5) (70.4) (33.5) (50.0)
SPLINE: 2.250 x 10 (57.15 x 10)
4.50 x .259 4.00 5.28 2.56 1.19 2.36 1.25x18 3 8.53.41 6.5.4.2131 (114.3 x 6.58) (101.6) (134.1) (65.0) (30.2) (60.0)
L
L2L3
P BSJ
L
L2
S
L3
P B
L
L2
S
L3
P BJ
SPICER CATALOGUE PAGE:- 50
SPICER
September
2014 © Driveline Services Australia Pty Ltd
MIDSHIP STUBS
Tube Butt W-EOS Size B L L2 L3 P J Type Part No. Notes / Suggestions
SPLINE: 2.340 x 16 (59.44 x 16)
4.09 x .180 3.75 5.31 2.63 1.38 2.36 1.25x18 3 6.53.311 6.5.4.1891 (103.90 x 4.57) (95.3) (134.9) (66.8) (35.1) (60.0) 231502 Nut
4.59 x .180 4.25 5.31 2.63 1.38 2.36 1.25x18 3 6.5.53.91 6.5.4.1891 (116.58 x 4.57) (108.0) (134.9) (66.8) (35.1) (60.0) 231502 Nut
SPLINE: 2.359 x 46 (59.92 x 46)
4.09 x .180 3.75 6.43 2.56 1.47 2.36 1.25x18 3 6.5.53.171 (103.9 x 4.57) (95.3) (163.3) (65.0) (37.3) (60.0)
SPLINE: 2.375 x 46 (60.30 x 46)
5.20 x .236 4.53 5.28 2.76 2.36 1.25x18 3 250.53.11 250.4.21.1 E.Yoke 210875.1X C/B
(132.0 x 6.0) (115.0) (134.0) (70.0) (60.0) 230123.6 Washer 250.74.11 Nut
MIDSHIP SMALL PARTS
Size Part No. Notes
M10 x 1.0 K2.72.1300 Retainer
K2.72.1300 Washer
K2.73.1300 Bolt
¾“ x 20 2.72.001 Split Pin
2.73.001 Washer
2.74.001 Castellated Nut
1” x 20 16.74.81 Castellated Nut
16.73.216 Washer
16.74.101 Self Lock Nut Flanged
1¼” x 18 231502 Self Lock Nut Flanged Std
20.74.91 Self Lock Nut Flanged Large
250.74.11 Self Lock Nut Flanged Large
230123.6 Washer
L
L2L3
P BSJ
L
L2
S
L3
P B
L
L2
S
L3
P BJ
SPICER CATALOGUE PAGE:- 51
SPICER
September
2014 © Driveline Services Australia Pty Ltd
BARREL
Spline Length Butt S L B Part No. Notes / Suggestions
1.060 x 16 6.55 2.51 1.55.A0135 (26.92 x 16) (166.4) (63.8)
1.375 x 16 5.31 1.81 K2.55.008 Suits Volvo Yokeshaft K2.82.001 (34.93 x 16) (135.0) (46.0) 45mm Bearing suits Centre Bearing CB20 / CB21
1.375 x 16 5.20 1.81 K2.55.700 Suits Land Rover Discovery. Yokeshaft K2.82.001 (34.93 x 16) (132.0) (46.0) 2.0”x.095 tube
1.375 x 16 5.91 2.56 2.55.A0118 (34.93 x 16) (150.0) (65.0)
1.500 x 16 7.00 2.76 3.55.A0128 (38.10 x 16) (178.0) (70.0)
1.500 x 16 6.49 3.00 3.55.165 Machined to suit 45mm C/Bearing (38.10 x 16) (165.0) (76.2)
1.750 x 16 9.02 3.50 4.55.A0138 (44.45 x 16) (229.0) (89.0)
2.000 x 16 8.46 3.54 5.55.A0148 (50.80 x 16) (215.0) (90.0)
2.500 x 16 10.24 3.94 6.55.A0158 (63.50 x 16) (260.0) (100.0) 3.000 x 16 10.50 4.50 6.5.55.A0168 (76.20 x 16) (266.7) (114.3)
SPICER CATALOGUE PAGE:- 52
SPICER
September
2014 © Driveline Services Australia Pty Ltd
YOKE SHAFTS
Spline C-EOS Angle S L L2 ° Part No. Notes / Suggestions
SERIES: 1140 Suits U/J: K5LGB80R 23.80 x 62.00
1.060 x 16 3.84 1.44 1.82.21 K1.3.A360 (Can be shortened) (26.92 x 16) (97.5) (36.6)
1.060 x 16 4.33 1.73 K1.82.2001 To suit K1.3.200 S.Yoke / K1.RB.200 Boot (26.92 x 16) (110.0) (44.0)
1.060 x 16 6.34 2.75 K1.82.2301 Suit Volvo (26.92 x 16) (161.0) (69.9)
SERIES: 1300 Suits U/J: K5L4R 26.99 x 74.61
1.375 x 16 7.28 3.54 K2.82.001 Landrover Discovery (34.9 x 16) (185.0) (90.0) Suit Volvo Barrel K2.55.008
SERIES: 1310 Suits U/J: K5.13XR 26.99 x 81.76
1.375 x 16 7.28 3.35 2.82.001 Suits Volvo – K2.55.008 (31.75 x 16) (185.0) (85.0)
1.375 x 16 6.57 2.00 30° 2.82.A111 2.3.128KX (31.75 x 16) (167.0) (50.8)
1.375 x 16 5.39 2.00 20° 2.82.21 2.3.348KX (34.93 x 10) (137.0) (50.8)
1.500 x 16 6.85 2.25 20° 2.82.002 Ford Transit use with barrel 3.55.165 (38.10 x 16) (174.0) (57.2)
SERIES: 1350 Suits U/J: 5.178X 30.16 x 92.08
1.500 x 16 5.19 2.00 20° 3.82.61 3.3.388KX (38.10 x 16) (131.8) (50.8)
1.500 x 16 6.81 2.50 9° 3.82.181 3.3.598KX (38.10 x 16) (173.0) (63.5)
SERIES: 1410 Suit U/J: K5GB10R 30.16 x 106.38
1.500 x 16 4.97 2.00 20° 3.82.81 3.3.468KX (38.10 x 16) (126.2) (50.8)
1.500 x 16 5.71 2.00 20° 3.82.145 Used with 3.3.118KX 217mm C-C comp (38.10 x 16) (145) (50.8) 50mm Slip can shorten Slip Yoke by 46mm 171mm C-C comp
SERIES: 1480 Suit U/J: 5.188X 34.93 x 106.38
1.560 x 16 5.71 2.00 3.82.1504 (39.62 x 16) (145.0) (50.8)
1.750 x 16 5.67 2.00 20° 3.82.1505 (44.45 x 16) (144.0) (50.8)
SPICER CATALOGUE PAGE:- 53
SPICER
September
2014 © Driveline Services Australia Pty Ltd
YOKE SHAFTS
Spline C-EOS Angle S L L2 ° Part No. Notes / Suggestions
SERIES: 1550 Suits U/J: 5.155X 34.93 x 126.20
2.362 x 26 Inv 9.84 4.82.250 4.3.260 (60.00 x 26) (250.0)
2.500 x 16 4.56 1.56 8° 4.82.191 (63.50 x 16) (115.8) (39.6)
SERIES: 1610 Suits U/J: 5.279X 47.63 x 134.94
2.000 x 16 7.87 2.75 22° 5.82.921 5.3.108KX (50.80 x 16) (200.0) (69.8)
2.000 x 16 10.43 3.35 30° 5.82.661 5.3.108KX – 5.3.288KX (50.80 x 16) (265.0) (85.0)
2.000 x 16 15.00 3.50 45° 5.82.751.2 5.3.2141KX (50.80 x 16) (381.0) (88.9)
SERIES: 1710 Suits U/J: 5.280X 49.21 x 154.78
2.500 x 16 8.16 3.00 22° 6.82.1251 (63.50 x 16) (207.3) (76.2)
2.500 x 16 9.66 3.50 24° 6.82.1171.10 (63.50 x 16) (245.4) (88.9)
2.500 x 16 12.09 3.50 45° 6.82.1281 (63.50 x 16) (307.1) (88)
2.500 x 16 13.09 3.50 45° 6.82.1281.1 (63.50 x 16) (332.5) (88.9)
2.500 x 16 14.00 4.00 45° 6.82.1061.1 (63.50 x 16) (355.6) (101.6)
2.500 x 16 15.03 4.00 45° 6.82.1061.3 (63.50 x 16) (381.8) (101.6)
2.500 x 16 16.03 4.17 45° 6.82.1061.11 (63.50 x 16) (407.2) (106.0)
3.250 x 18 5.25 2.00 8° 6.82.341 Use assembly 6.03.167 (82.55 x 18) (133.4) (50.8)
SERIES: 1760 Suits U/J: 5.407X 49.21 x 177.80
2.500 x 16 11.00 4.00 6.3.82.21.1 (63.50 x 16) (279.4) (101.6) WHILE STOCKS LAST
SPICER CATALOGUE PAGE:- 54
SPICER
September
2014 © Driveline Services Australia Pty Ltd
YOKE SHAFTS
Spline C-EOS Angle S L L2 ° Part No. Notes / Suggestions
SERIES: 1810 Suits U/J: 5.281X 49.21 x 191.69
3.000 x 16 11.44 4.50 30° 6.5.82.451.1 (76.2 x 16) (290.0) (114.3)
3.000 x 16 12.81 4.50 30° 6.5.82.461.13 (76.20 x 16) (325.4) (114.3)
3.000 x 16 15.06 4.50 30° 6.5.82.461.10 (76.20 x 16) (382.5) (114.3)
3.250 x 18 6.72 2.75 12° 6.5.82.511.1 (82.55 x 18) (170.7) (69.9)
3.250 x 18 7.22 2.75 12° 6.5.82.511.3 (82.55 x 18) (183.4) (69.9)
SPICER CATALOGUE PAGE:- 55
SPICER
September
2014 © Driveline Services Australia Pty Ltd
SPL170, SPL250 & RPL25
SPL170 PSA U.Joint Slip Assembly Tube Weld Yoke Strap Kit Lock Plate Kit
SPL170
SPL.170X 170.6.001 120 x 5 170.28.27 170.70.18X 211941X Use 120 x 6 Machine Butt
SPL170 PSA
U.Joint Complete Assembly Without U.Joints Complete Assembly with U.Joints
SPL170
SPL.170X 170.03.443X 170.03.443 (442.8mm C-C comp 150mm slip) Strap Kits 170.70.18X)
SPL.170X 170.03.482X 170.03.482 (482.8mm C-C comp 180mm slip) Strap Kits 170.70.18X
SPL250 PSA
U.Joint Slip Assembly Tube Weld Yoke Strap Kit Lock Plate Kit
SPL170
SPL.250X 250.6.001 132 x 6 250.28.17 250.70.18X 211941X Use 130 x 6 Machine Butt
SPL250 JSA
U.Joint Weld Yoke Tube Midship Stub End Yoke Centre Bearing Nut & Washer
SPL250
SPL.250X 250.28.17 132 x 6 250.53.11 250.4.21.1 210875.1X 250.74.11 Nut Use 130 x 6 Machine Butt Alt 210661.1X 230123.6 Washer
RPL25 PSA
U.Joint Slip Assembly Tube Weld Yoke
RPL25
CP25RPLS 25RP.6.001 4.59 x .180 25RP.28.001
RPL25 JSA
U.Joint Weld Yoke Tube Midship Stub End Yoke Centre Bearing Nut & Washer
RPL25
CP25RPLS 25RP.28.001 4.59 x .180 6.5.53.171 25RP.4.001 210875.1X 231502 Nut Alt 210661.1X 230123.6 Washer
SPICER CATALOGUE PAGE:- 56
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DOUBLE CARDAN COMPONENT PARTS
1 2 3 4 Overall Centering Uni CV / Flange Weld Centre "H" Complete Length Tube Repair
Joints Yoke Yoke Yoke Assy Type L Size Kit
SERIES: 1300 Suits K5L4R 26.99 x 74.61
K5L4R - - 800R1300 2 Refer Note SCV82ANG Sold as Complete Assembly only – Machine butt to suit 2” tube L = 154mm
SERIES: 1310 Suits U/J 5.433.1X 26.99 x 81.76
- - 800R13002 181mm 2.5” x .095”
Sold as Complete Assembly only
5.433.1X SCV82 2.28.1777X 2.26.507 800R1310.1 1 4.125 2.000 x .120 SCV82A (104.7) (50.8 x 3.05)
5.433.1X SCV82 2.28.1747X 2.26.507 800R1310.2 1 4.125 2.500 x .083 SCV82A (104.7) (63.5 x 2.11)
5.433.1X 211229X 2.28.1777X 2.26.507 800R1310.3 2 5.75 2.000 x .120 SCV82A (146.0) (50.8 x 3.05)
800R1310.SAGINAW Use 3R Complete Assy : 4137268
SPICER CATALOGUE PAGE:- 57
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DIMENSIONAL DATA on PARTS & COMPLETE ASSYS
Part No
Butt B
PCD D
Hole D1
Bolt Holes D2 D3
Spigot K
C-C L1
C-W L2
C-F L3
Notes
SERIES: 1310 SUITS U/J 5.433.1X 26.99 x 81.76 SCV82
5/16 UNF
1.50 (38.1)
2.34 (59.4)
2.26.507 2.69 (68.3)
2.28.1979X 1.03 (26.2) 1.44
(36.6) Suits:
1.250 x .120 (31.75 x 3.05)
2.28.1777X 1.77 (45.0) 1.44
(36.6) Suits:
2.000 x .120 (50.8 x 3.05)
2.28.1747X 2.34 (59.4) 1.44
(36.6) Suits:
2.500 x .083 (63.5 x 2.11)
211229X 3.50 (88.9)
0.49 (12.5)
2.475 (62.8)
2.475 (62.86)
2.00 (F) (50.8) 1.62
(41.1)
2.21.3191 94.75 4X10.5 67.0 67.0 65.0 (M) 49.2 Landrover Discovery
COMPLETE DOUBLE CARDAN ASSEMBLIES – 1310
800R1310.4
59 79.35 9.60 51 60.8 60.33
Landrover Suits
2.50 x 0.095
800R1310.5
59 95.00 10.20 67.2 67.2 65.00
Landrover Discovery
Suits 2.50 x 0.095
800R1310.7
59 93.34 10.20 66 66 46.00
Toyota Suits
2.50 x 0.095
800R1310.6
59 90.00 10.20 58 69 60.00 Mitsubishi
Suits 2.50 x 0.095
800R1310.8
59 104.65 10.2 74 74 60.00
Isuzu Suits
2.50 x 0.095
SPICER CATALOGUE PAGE:- 58
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DOUBLE CARDAN COMPONENT PARTS
1 2 3 4 Overall Centering Uni CV / Flange Weld Centre "H" Complete Length Tube Repair
Joints Yoke Yoke Yoke Assy Type L Size Kit
SERIES: 3R Suits U/J: 114.3105 28.58 x 65.10
114.3105 3R.21.482 3R.28.3113 3R.26.027 4137268 3 6.563 2.000 x .120 CVK2A (166.7) (50.8 x 3.05)
DIMENSIONAL DATA ON PARTS
Butt PCD Hole Bolt Pattern Spigot C-C C-W C-F Part No. B D D1 D2 D3 K L1 L2 L3 Notes
SERIES: 3R Suits U/J: 114.3105 28.58 x 65.10
3R.26.057 - - - - - - 3.25 - - (82.5)
3R.28.3113 1.77 - - - - - - 1.422 - Suits: 2.000 x .065 (45.1) (36.1) (50.8 x 1.65)
3R.28.3111 2.625 - - - - - - 1.422 - Suits: 2.750 x .120 (66.6) (36.1) (69.85 x 3.05)
3R.21.482 - 4.25 .453 3.00 3.00 3.125 (F) - - 1.688 (107.9) (11.5) (76.3) (76.3) (79.3) (42.8)
SPICER CATALOGUE PAGE:- 59
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DOUBLE CARDAN COMPONENT PARTS
1 2 3 4 Overall Centering Uni CV / Flange Weld Centre "H" Complete Length Tube Repair
Joints Yoke Yoke Yoke Assy Type L Size Kit
SERIES: 1330 Suits U/J: RUJ3002.1A 26.99 x 92.08
RUJ3002.1A SCV79 2.28.2137X 2.26.527 800R1330.1 1 4.125 2.500 x .083 SCV82A (104.7) (63.5 x 2.11)
DIMENSIONAL DATA ON PARTS
Butt PCD Hole Bolt Pattern Spigot C-C C-W C-F Part No. B D D1 D2 D3 K L1 L2 L3 Notes
SERIES: 1330 Suits U/J: RUJ3002.1A 26.99 x 92.08
SCV79 - - 5/16 UNF 1.50 2.875 - - - - (38.1) (73.0)
2.26.527 - - - - - - 2.75 - - (69.9)
2.28.2137X 2.344 - - - - - - 1.38 - Suits: 2.500 x .083 (59.5) (35.1) (63.5 x 2.11)
SPICER CATALOGUE PAGE:- 60
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DOUBLE CARDAN COMPONENT PARTS
1 2 3 4 Overall Centering Uni CV / Flange Weld Centre "H" Complete Length Tube Repair
Joints Yoke Yoke Yoke Assy Type L Size Kit
SERIES: 1350 Suits U/J 5.178X.1A 30.16 x 92.08
5.178X.1A 3.83.024X 3.28.1747.1X 3.26.757 800R1350.1 2 6.313 2.750 x .083 SCV82ANG (160.3) (69.85 x 2.11)
DIMENSIONAL DATA ON PARTS
Butt PCD Hole Bolt Pattern Spigot C-C C-W C-F Part No. B D D1 D2 D3 K L1 L2 L3 Notes
SERIES: 1350 Suits U/J 5.178X.1A 30.16 x 92.08
3.26.757 - - - - - - 2.875 - - (73.0)
3.28.3281X 2.32 - - - - - - 1.44 - Suits: 2.500 x .095 (58.9) (36.5) (63.50 x 2.41)
3.28.1747.1X 2.59 - - - - - - 1.81 - Suits: 2.750 x .083 (65.7) (45.9) (69.85 x 2.11)
3.28.1327.1X 2.84 - - - - - - 1.81 - Suits: 3.000 x .083 (72.2) (45.9) (76.20 x 2.11)
3.83.024X - 4.25 M12x1.75 3.00 3.00 2.00 (F) - - 1.625 Ford (107.9) (76.3) (76.3) (50.8) (41.2)
3.83.025X - 4.25 M12x1.75 3.00 3.00 2.68 (F) - - 1.625 Dodge Ram (107.9) (76.3) (76.3) (68.0) (41.2)
3.83.3281X - 4.25 .438 3.00 3.00 3.125 (F) - - 1.625 Saginaw (107.9) (11.1) (76.3) (76.3) (79.3) (41.2)
SPICER CATALOGUE PAGE:- 61
SPICER
September
2014 © Driveline Services Australia Pty Ltd
CV BALL REPAIR KITS
Kit No. Kit No.
Description W/ Ball W/O Ball Notes
SAGINAW TYPE:
Saginaw Type - With large ball CVK2 CVK1 GM OEM #: 7814308 7809156 7816006 With step on ball (Ball size .9075)
Saginaw Type - With large ball CVK2A CVK1 GM OEM #: 7815848 7829456 W/Out step on ball (Ball size .9075) Chrysler OEM #: 4030849 4069697
Saginaw type - With small ball CVK4 CVK3 GM OEM #:1389864. To use CVK3 #7808979 (Ball size .8775)
Saginaw type - With small ball CVK6 CVK5 Supplied with small ball (Ball size .8775)
SPICER TYPE:
1310/1330 Series Repair Kit SCV82A Suits greasable assys
1310/1330 Series Repair Kit SCV82ANG Suits non greasable assys
Dust Boot 2.86.418 Used in non lube 1310, 1330 & 1350 assys
CV KIT REPAIR YOKES
Description Part No. Notes
1210 Series repair yoke SCV42
1330 Series repair yoke SCV79
1310 Series repair yoke SCV82
FIBRE
SPICER CATALOGUE PAGE:- 62
SPICER
September
2014 © Driveline Services Australia Pty Ltd
CARDAN ADAPTOR FLANGES
Spigot PCD Bolt Pattern F-C K D D1 D2 D3 L Part No. Notes
SERIES: 1310/SAGINAW
3.125 (F) 4.25 .453 3.00 3.00 2.38 2.83.188.1X Bolts supplied (79.4) (108.0) (11.5) (76.2) (76.2) (60.5)
SERIES: 1310/TOYOTA
1.811 (M) 3.59 .315 2.36 2.68 2.91 2.83.288 Bolts supplied (46.0) (91.2) (8.00) (59.9) (68.1) (73.9)
SPICER CATALOGUE PAGE:- 63
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DUST CAP KITS
Spline Splined Part No. S Y / N Type Compound Suits Notes
10.14.29 4 Spline No Crimp Steel 1000 Suits steering shafts
D1A 1.06 x 16 Yes Crimp Steel 1100 (26.9 x 16)
D1B 1.06 x 16 No Crimp Steel 1140 (26.9 x 16)
DCK14A 1.06 x 16 No Screw Steel 1140 (26.9 x 16)
D2K 1.25 x 16 No Crimp Steel 1310 (31.7 x 16)
D2C 1.38 x 16 No Screw Rubber 1310 (35.1 x 16)
28.0194 1.38 x 16 No Snap On Rubber 1310/1330 One piece - Non greasable
(35.1 x 16)
28.0194.1 1.38 x 16 No Snap On Rubber 1310/1330 One piece - Greasable
(35.1 x 16)
28.0195 1.38 x 16 Yes Snap On Rubber 1310/1330 One piece
(35.1 x 16)
D3E 1.38 x 16 Yes Screw Steel 1310/1350 Slip yoke thread dia - 1.66”
(35.1 x 16)
D3G 1.38 x 16 Yes Screw Steel 1350/1410 Slip yoke thread dia - 1.78”
(35.1 x 16)
D3A 1.50 x 16 No Screw Steel 1350/1410 (38.1 x 16)
D3F 1.50 x 16 No Screw Steel 1410 (38.1 x 16)
D3K 1.50 x 16 Yes Screw Steel 1410 (38.1 x 16)
D3H 1.56 x 16 No Screw Rubber 1410/1480 (39.6 x 16)
D3J 1.56 x 16 Yes Screw Steel 1480 (39.6 x 16)
SPICER CATALOGUE PAGE:- 64
SPICER
September
2014 © Driveline Services Australia Pty Ltd
DUST CAP KITS
Spline Splined Part No. S Y / N Type Compound Suits Notes
DCK51A 1.75 x 16 No Screw Steel 1510 (44.5 x 16)
D4A 1.75 x 16 No Screw Steel 1500 (44.5 x 16)
D4J 1.75 x 16 No Screw Rubber 1550 (44.5 x 16)
D4K 1.75 x 16 Yes Screw Steel 1550 (44.5 x 16)
D4L 2.67 x 18 No Screw Steel 1550 Close couple use
(67.8 x 18)
D5C 2.69 x 18 No Screw Steel 1610 Close couple use (68.3 x 18)
D5G 2.00 x 16 Yes Screw Steel 1610 Crimp style
(50.8 x 16)
5.86.68 2.00 x 16 No Screw Rubber 1610 (50.8 x 16)
D5E 2.00 x 16 No Screw Steel 1650 (50.8 x 16)
D6A 2.50 x 10 No Screw Steel 1710 (50.8 x 10)
D6G 2.50 x 16 Yes Screw Steel 1710 Crimp style
(50.8 x 16)
6.3.86.18 2.50 x 16 No Screw Rubber 1710 (63.5 x 16)
D9A 3.00 x 16 No Screw Steel 1880/1950 (76.2 x 16)
6.5.86.38 3.00 x 16 No Screw Rubber 1810 (76.2 x 16)
D6E 3.25 x 18 Yes Screw Steel 1710/1810 (82.6 x 18)
SPICER CATALOGUE PAGE:- 65
SPICER
September
2014 © Driveline Services Australia Pty Ltd
WELCH PLUGS
* These welch plugs are specifically designed for use with Neapco manufactured products. These parts may be used in replacement on other manufacturers products, but actual fit may require machining or welding.
Part No. A B Suits Notes
* 5.68.54 2.20 0.44 1610 Steel (55.9) (11.2)
* 6.68.71 2.75 1.25 1710 Steel (69.9) (31.8)
* 6.68.51 2.75 0.53 1710/1760 Steel (69.9) (13.4)
* 6.3.68.14 2.75 1.09 1760 Steel (69.9) (27.7)
* 8.68.13 3.25 0.62 1810 Steel (82.6) (15.7)
6.5.68.13 2.56 - 1710 Steel (65.0)
6.5.68.64 3.32 0.85 1810 Plastic (84.3) (21.6)
6.5.68.74 3.32 1.53 1810 Plastic (84.3) (38.9)
6.68.64 2.82 0.80 1710 Plastic (6.3.2651KX) (71.6) (20.3)
6.68.74 2.82 1.50 1710 Plastic (6.3.2671KX) (71.6) (38.1)
SPICER CATALOGUE PAGE:- 66
SPICER
September
2014 © Driveline Services Australia Pty Ltd
U-BOLTS, BEARING STRAPS AND LOCK TABS
Bearing CL-CL Length Thread Per C L L1 J Type Part No. Unit Notes
U-BOLTS AND BEARING STRAPS
1.125 1.594 1.82 .31 x 24 UNF 1 105 2 Ford 9” (28.58) (40.5) (46.2)
1.078 1.50 0.62 .250 x 28 UNF 2 106 2 21R (27.38) (38.1) (15.7)
1.063 1.41 1.72 .31 x 24 UNF 1 2.94.28X 2 1310/1330 (27.00) (35.8) (43.7)
1.063 1.59 1.50 .31 x 24 UNF 2 107 2 1310/1330 (27.00) (40.4) (38.1)
1.187 1.66 2.00 .375 x 24 UNF 1 3.94.18X 2 1350/1410 Spicer (30.16) (42.2) (50.8)
1.187 1.66 1.31 .31 x 24 UNF 2 3.70.28X.GM 2 1350/1410 GM (30.16) (42.2) (33.3)
1.187 1.81 0.75 .3125 x 24UNF 2 3.70.28X 2 1350/1410 (30.16) (45.9) (19.1)
1.375 1.91 2.28 .44” x 20 UNF 1 3.94.28X 2 1480/1550 (34.93) (48.5) (57.9)
1.375 2.12 0.75 .375 x 24 UNF 2 3.70.38X 2 1480/1550 (34.93) (53.8) (19.1)
1.625 2.38 - .50 x 20 UNF 2 5.70.18X 1 1650 (41.28) (60.5)
1.875 2.50 0.75 .375 x 24 UNF 2 5.70.28X 2 1610 (47.63) (63.5) (19.1)
1.937 2.81 1.0 .50 x 20 UNF 2 6.5.70.18X 2 1710/1810 (49.21) (70.6) (25.4)
2.165 3.20 - M12 x 1.25 2 170.70.18X 2 SPL170 (55.00) (81.3)
2.362 3.40 - M12 x 1.25 2 250.70.18X 2 SPL250 (60.00) (86.46)
LOCK TABS
- 2.34 - - 3 98.741 1 1610 (59.4)
- 2.44 - - 3 230323 1 1710/1810 (62.0)
- 2.81 - - 3 231009 1 1880 NLA (71.4)
- - - 3 98.743 1 1800 NLA
SPICER CATALOGUE PAGE:- 67
SPICER
September
2014 © Driveline Services Australia Pty Ltd
COUPLINGS (Metric Only)
PCD D
H Hole
OD Ǿ
D1
Width
Note
Part No.
Notes
76 38 107 8 x 10 38 * RC.BMW.001 BMW All 3/5 Series –80
78 41 107 6 x 10 28 * RC.BMW.002 BMW 4/6 Cyl.2.3lt Auto 76-/Man 80-, Nissan Pintara
80 40 114 6 x 10 25.7 * RC.MER.009 Genuine No. 201.410.0715
94 45 133 6 x 12 30 * RC.BMW.004 BMW 5/6/7/ Series Auto –80
97 43 133 6 x 12 45 RC.BMW.005 BMW 6/7 Series Man –80
96 50 134 6 x 8 35 BA Falcon 6 cyl (Except Turbo)
105 56 142 6 x 12 32/35 BA/BF Series 1 Falcon. V8 & Turbo 6, BA MK2 6cy some BF 6 cyl Series 1.
110 56 148 6 x 12 32/35 BF Falcon Series II on FG Falcon
96 50 130 6 x 12 35 RC.JUR.002 Suit BA-BF Falcon - Holden
105 56 143 6 x 12 35 RC.JUR.004 Ford Transit 2002 auto
96 50 130 6 x 12 30 * RC.JUR.001 Suits Ford, Jaguar, Volvo, Vauxhall, BMW
* PLEASE NOTE: Some Couplings may have a steel-retaining strap. Do not remove the strap until after
installation in the vehicle.
OD
H
SPICER CATALOGUE PAGE:- 68
SPICER
September
2014 © Driveline Services Australia Pty Ltd
COUPLINGS (Metric Only)
PCD D
H Hole
OD Ǿ
D1
Width
Note
Part No.
Notes
96 49 133 6 x 12 30 RCA-1059 Commodore VS/VT V6 Manual (Front Only)
100 41 149 6 x 12 36/40 RCA-1058 Commodore VT Series 1 up to 6/99 V8 Manual (Front Only)
96 49 133 6 x 12 35/38 Commodore VT Series 2 6/99 on 5.7L V8 Gen 3 Manual only /Front only
96 50 132 6 x 12 30 V6 auto RCA-1060 Commodore VX-VZ VE up to 03/2008 Front & Rear V6
manual front only
96 49 133 6 x 12 35 RCA-1061 Commodore VX-VZ V8 Manual & auto F&R all VX-VE to 03/08 Rear (except V6 auto)
110 58 152 6 x 12 35/38.5 RCA-1062 Commodore VE V8 front and rear
105 56 141 6 x 12 32/35 Commodore VE V6 front and rear 3/2008 on
78 38 111 6 x 12 32 Hyundai Santa Fe V6 Tuscon
96 50 131 6 x 12 30 Land Rover Discovery (Rear)
96 45 133 6 x 10 30 RC.100R231 Nissan Pintara Manual
80 40 125 6 X 8 20 TO-PC-305P Tarago auxiliary shaft (12mm locating bush) petrol
80 40 125 6 X 8 20 TO-PC-305P.1 Tarago auxiliary shaft (14mm locating bush) petrol
85 42 120 6 X 8 20 TO-PC-306D Tarago auxiliary shaft (14mm locating bush) diesel
OD
H
SPICER CATALOGUE PAGE:- 69
SPICER
September
2014 © Driveline Services Australia Pty Ltd
BALANCE WEIGHTS
Description Weight Part No. Notes
4.0 grams (0.141 oz) DLW.04
5.0 grams (0.176 oz) DLW.05 Rectangle 26 x 12
8.0 grams (0.28 oz) DLW.08
10.0 grams (0.35 oz) DLW.10
10.0 grams (0.35 oz) DLW.10A Rectangle 15 x 38
15.0 grams (0.259 oz) DLW.15 Rectangle 26 x 37
20.0 grams (0.70 oz) DLW.20
24.0 grams (0.847 oz) DLW.24 Rectangle 35 x 38
30.0 grams (1.00 oz) DLW.30
35.0 grams (1.235 oz) DLW.35 Rectangle 53 x 38
40.0 grams (1.412 oz) DLW.40 Rectangle 60 x 38
47.0 grams (1.659 oz) DLW.47 Rectangle 70 x 38
50.0 grams (1.764 oz) DLW.50
70.0 grams (2.469 oz) DLW.70
140.0 grams (4.938 oz) DLW.140
SPICER CATALOGUE PAGE:- 70
SPICER
September 2014 © Driveline Services Australia Pty Ltd
STANDARD COMPONENTRY ASSEMBLED LENGTHS (Centre to Centre of joints with 100mm of tube)
Series Flange
Uni
Slip
Stub
Tube
Weld Yoke
Uni
Flange
Compressed C/C with 100mm
tube
Extended C/C with 100mm
tube
1140 1.2.39 (41.2) K5LGB80R K1.3.A360 K1.42.GB1901 2.00x.065 K1.26.GB17 K5LGB80R 1.2.39 (41.2) 265mm 304mm
1210 2.2.899 (38.0) 5.443X 2.3.8861KX 2.40.1741 2.00X.083 2.28.2417 5.443X 2.2.899 (38.0)
1310 2.2.329 (35.8) K5.13XR 2.3.128KX 2.40.1031 2.00x.083 2.28.357 K5.13XR 2.2.329 (35.8) 305mm 357mm
1310 2.2.329 (35.8) K5.13XR 2.3.128KX 2.40.2701 2.00x.095 2.28.577 K5.13XR 2.2.329 (35.8) 305mm 357mm
1310 2.2.329 (35.8) K5.13XR 2.3.5821KX 2.40.1851 2.50x.083 2.28.367 K5.13XR 2.2.329 (35.8) 385mm 485mm
1330 - RUJ3002 2.3.7481KX 2.40.1221 3.00x.065 2.28.1177 RUJ3002 - 345mm 405mm
1350 3.2.119 (39.6) 5.178X 3.3.598KX 3.40.3901 3.00x.095 3.28.57 (.083) 5.178X 3.2.119 (39.6) 345mm 383mm
1350 3.2.119 (39.6) 5.178X 3.3.488KX 3.40.3891 3.00x.095 3.28.57 (.083) 5.178X 3.2.119 (39.6) 375mm 465mm
1410 3.2.159 (42.9) K5GB10R 3.3.118KX 3.40.3901 3.00x.095 3.28.267 K5GB10R 3.2.159 (42.9)
1410 3.2.159 (42.9) K5GB10R 3.3.508KX 3.40.3891 3.00x.095 3.28.267 K5GB10R 3.2.159 (42.9)
1480 3.2.479 (50.8) 5.188X 3.3.1601KX 3.40.1571 3.50x.083 3.28.537 5.188X 3.2.479 (50.8) 367mm 427mm
1480 3.2.479 (50.8) 5.188X 3.3.1641KX 3.40.1391 3.50x.083 3.28.537 5.188X 3.2.479 (50.8) 435mm 555mm
1480 3.2.479 (80.8) 5.188X 3.3.1661KX 3.40.1411 3.50x.083 3.28.537 5.188X 3.2.479 (80.8) 480mm 645mm
1510 K4.2.GB239 (63.5) K5GB22R K4.3.A1120 K4.42.GB1791 3.00x.095 K4.26.GB477 K5GB22R K4.2.GB239 (63.5) 385mm 450mm
1510 K4.2.GB239 (63.5) K5GB22R K4.6.001 3.50x.134 K4.26.GB457 K5GB22R K4.2.GB239 (63.5) Machine Butts
1550 4.2.669 (50.8) 5.155X 4.3.1241KX 4.40.761 3.50x.095 4.28.307 5.155X 4.2.669 (50.8)
1550 4.2.669 (50.8) 5.155X 4.3.1431KX 4.40.721 3.50x.095 4.28.417 5.155X 4.2.669 (50.8)
SPICER CATALOGUE PAGE:- 71
SPICER
September 2014 © Driveline Services Australia Pty Ltd
STANDARD COMPONENTRY ASSEMBLED LENGTHS (Centre to Centre of joints with 100mm of tube)
Series Flange
Uni
Slip
Stub
Tube
Weld Yoke
Uni
Flange
Compressed C/C with 100mm
tube
Extended C/C with 100mm
tube
1610 5.2.279 (69.9) 5.279X 5.3.108KX 5.40.1191 3.50x.134 5.28.627 5.279X 5.2.279 (69.9) 410mm 473mm
1610 5.2.279 (69.9) 5.279X 5.3.288KX 5.40.1011 3.50x.134 5.28.627 5.279X 5.2.279 (69.9) 477mm 573mm
1610 5.2.279 (69.9) 5.279X 5.3.2261KX 5.40.1011 3.50x.134 5.28.627 5.279X 5.2.279 (69.9) 500mm 622mm
1610 5.2.379 (47.6) 5.279X 5.3.198KX 5.40.1181 3.50x.134 5.28.627 5.279X 5.2.379 (47.6)
1710 6.2.749 (72.6) 5.280X 6.3.1461KX 6.40.311 4.00x.134 6.28.347 5.280X 6.2.749 (72.6) 465mm 535mm
1710 6.2.749 (72.6) 5.280X 6.3.2671KX 6.40.541 4.00x.134 6.28.347 5.280X 6.2.749 (72.6) 463mm 550mm
1710 6.2.749 (72.6) 5.280X 6.3.2651KX 6.40.521 4.00x.134 6.28.347 5.280X 6.2.749 (72.6) 515mm 650mm
1760 6.3.2.19 (85.7) 5.407X 6.3.3.21KX 6.40.521 4.00x.134 6.3.28.17 5.407X 6.3.2.19 (85.7)
1810 6.5.2.329 (85.7) 5.281X 6.5.3.1351KX 6.5.40.201 4.50x.134 6.5.28.117 5.281X 6.5.2.329 (85.7) 490mm 565mm
1810 6.5.2.329 (85.7) 5.281X 6.5.3.1371KX 6.5.40.191 4.50x.134 6.5.28.117 5.281X 6.5.2.329 (85.7) 545mm 665mm
1880 8.2.109 (91.3) 5.308X 8.3.411KX 8.40.101 4.50x.259 8.28.147 5.308X 8.2.109 (91.3) 555mm 675mm
SPICER CATALOGUE PAGE:- 72
SPICER
September 2014 © Driveline Services Australia Pty Ltd
SHORT COUPLED SHAFTS
Series STD Flange
Slip
Yoke Shaft
Compressed F-F
Compressed C-C
Extended F-F
Extended C-C
Total Slip
Angle
Notes
1140 1.2.39 K1.3.A360 K1.82.2001 215.4mm 155mm 235.4mm 175mm 20 Can be shortened to 132mm C-C comp if slip yoke shortened by 23mm
1310 2.2.329 2.3.348KX 2.82.21 232mm 162mm 257mm 187mm 25 20°
2.2.329 2.3.128KX 2.82.A111 262mm 192mm 315mm 245mm 53 20°
1350 3.2.119 3.3.388KX 3.82.61 242mm 162mm 261mm 181mm 19 8°
3.2.119 3.3.598KX 3.82.181 283mm 203mm 337mm 257mm 54
1410 3.2.159 3.3.468KX 3.82.81 241mm 155mm 260mm 174mm 19 8°
3.2.159 3.3.2041KX 3.82.145 274mm 188mm 309mm 223mm 35 22°
3.2.159 3.3.118KX 3.82.145 303mm 217mm 338mm 252mm 35 22° Can be shortened to 171mm C-C comp if slip yoke shortened by 46mm
3.2.159 3.3.508KX 3.82.145 336mm 250mm 371mm 285mm 35 22°
1480 3.2.479 3.3.1601KX 3.82.1504 336.6mm 235mm 361.6mm 260mm 25 22°
3.2.479 687.30.03.335LZ 335mm 110 22°
1510 K4.2.001 K4.03.170LZ 250mm 170mm 285mm 205mm 35 8°
K4.2.GB239 K4.03.315LZ 442mm 315mm 542mm 415mm 100 20° Can be shortened to 240mm C-C comp
1550 4.2.679 4.3.1261KX 4.82.191 216mm 139mm 241mm 164mm 25 8°
1610 5.2.379 5.03.150 245mm 150mm 262mm 167mm 17 8°
5.2.279 5.3.108KX 5.82.921 405mm 265mm 465mm 325mm 60 20°
5.2.279 5.3.108KX 5.82.661 450mm 310mm 515mm 375mm 65 20°
SPICER CATALOGUE PAGE:- 73
SPICER
September 2014 © Driveline Services Australia Pty Ltd
SHORT COUPLED SHAFTS
Series STD Flange
Slip
Yoke Shaft
Compressed F-F
Compressed C-C
Extended F-F
Extended C-C
Total Slip
Angle
Notes
5.2.279 5.3.288KX 5.82.661 480mm 340mm 550mm 410mm 70 30° Working angle limited to 20° when flanges fitted
1610 5.2.279 5.3.288KX 5.82. 781 495mm 355m 560mm 420mm 65 25° Working angle limited to 20° when flanges fitted
5.2.279 5.3.2261KX 5.82.661 520mm 380mm 590mm 450mm 70 30° Working angle limited to 20° when flanges fitted
5.2.279 5.3.2141KX 5.82.751.6 430mm 535mm 105 45°
5.2.279 5.3.2141KX 5.82.751.2 455mm 595mm 140 45°
1710 6.2.769 6.03.167 268.6mm 167mm 292.6mm 191mm 24 8°
6.2.769 6.03.194 295.6mm 194mm 309.6mm 218mm 24 8°
6.2.749 6.3.2671KX 6.82.1171.10 487.4mm 335mm 547.4mm 395mm 60 22°
6.2.749 6.3.2671KX 6.82.1281 507.4mm 355mm 606.4mm 454mm 99 22/45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.2671KX 6.82.1281.1 527.4mm 375mm 632.4mm 480mm 105 22/45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.3021KX 6.82.1281 542.4mm 390mm 633.4mm 481mm 91 45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.2651KX 6.82.1281.1 558.4mm 406mm 685.4mm 533mm 127 29/45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.2551KX 6.82.1281.1 567.4mm 415mm 693.4mm 541mm 126 45° Working angle limited to 22° when flanges fitted
SPICER CATALOGUE PAGE:- 74
SPICER
September 2014 © Driveline Services Australia Pty Ltd
SHORT COUPLED SHAFTS
Series STD Flange
Slip
Yoke Shaft
Compressed F-F
Compressed C-C
Extended F-F
Extended C-C
Total Slip
Angle
Notes
1710 6.2.749 6.3.2551KX 6.82.1061.1 585.4mm 433mm 720.4mm 568mm 125 45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.2551KX 6.82.1061.3 612.4mm 460mm 749.4mm 597mm 137 45° Working angle limited to 22° when flanges fitted
6.2.749 6.3.2551KX 6.82.1061.11 638.4mm 486mm 775.4mm 623mm 137 45° Working angle limited to 20° when flanges fitted
1810 6.5.2.329 6.5.3.1351KX 6.5.82.451.1 533.4mm 362mm 612.4mm 441mm 79 30°
6.5.2.329 6.5.3.1351KX 6.5.82.461.13 555.4mm 384mm 641.4mm 470mm 86 30°
6.5.2.329 6.5.3.1371KX 6.5.82.461.8 582.4mm 411mm 709.4mm 538mm 127 30°
6.5.2.329 6.5.3.1371KX 6.5.82.461.10 614.4mm 443mm 741.4mm 570mm 137 30°