Post on 25-Jul-2020
#HFMC17
.
Water Quality Requirements of AS/NZS 4187:2014
Presenter Robin Burgess
#HFMC17
• Why Water Treatment
• Some Common Problems
• AS/NZS 4187:2014
• Purification Methods
• The Ring MainProduct Water Distribution Loop
• Summary
Table of contents
Why Water Treatment / Poor Quality Water Instruments
• Compromised sterilisation requires higher levels of Maintenance
• Shortens the life of instruments replacement costs
• Repairs and replacements can be costly >10% of Inventory Cost Annually
Equipment
• Premature ageing of reprocessing equipment
• Shortened life of reprocessing equipment
Compliance – Patient Safety
• AS/NZS 4187:2014
• ISO 15883
• EN 285
• GENCA
#HFMC17
Elevated hardness:
Water with residual hardness may cause white/grey staining described in the literature as “water spots”. Residual carbonate hardness may also cause a shift of pH when water is being heated and so contributes to the corrosion.
Elevated / High Chloride:
Chloride is the number one reason for pitting and stress corrosion. The effect depends on a number of factors such as concentration; contact time; temperature and resistance of the instrument material.
Elevated / High Silicate:
Silicate causes grey or coloured staining on instruments. To achieve completely stain free instruments, for example some instrument manufacturers recommend a maximum of 0.4mg/l. The effect increases dramatically in process steps where the water is allowed to dry on the instruments.
pH-Value:
An elevated or low pH-value may cause oxidation of the surface. The effect will depend on temperature, contact time and neutralization. Typical causes are carry over of chemistry and/or water impurities.
Elevated Conductivity:
Conductivity is an indicator for the sum of all free ions. Conductivity above the standard indicated impurities, but it is not always possible to determine the exact origin.
Why Water Treatment
#HFMC17
• Some Common Problems
Sodium
Na+
Chloride
Cl-
Carbonate
CO32-
Potassium
K+ Aluminum
Al3+
Iron
Fe2+
Copper
Cu2+
Zinc
Zn2+ Phosphate
PO43-
Sulfate
SO42-
Nitrate
NO3-
Fluoride
F-
Hydroxide
OH-
Bicarbonate
HCO3-
Water
H2OCalcium
Ca2+
Magnesium
Mg2+
Silicate
SiO2
Major cause of instrument damage:
• Sulfate, Nitrate and Phosphate can cause
―Oxidation
―Corrosion
• Chlorides
―Major cause of pitting (rust spots)
Corrosive Anions• Some Common Problems
Biofilm , Bacteria , Spores
#HFMC17
• Silicates (minerals with silicon)
• Found in locations where the tap water is taken from sandy locations
• Tend to deposit on instruments causing opaque (at the beginning), or dark blue when layers growing thicker
• In steam cause a typical “snake skin” pattern
Silicate
• Some Common Problems
#HFMC17
• .
• Some Common Problems
#HFMC17
• Some Common Problems
• Hard Water Elements
Sodium
Na+
Chloride
Cl-
Carbonate
CO32-
Potassium
K+ Aluminum
Al3+
Iron
Fe2+
Copper
Cu2+
Zinc
Zn2+ Phosphate
PO43-
Sulfate
SO42-
Nitrate
NO3-
Fluoride
F-
Hydroxide
OH-
Bicarbonate
HCO3-
Water
H2OCalcium
Ca2+
Magnesium
Mg2+
Silicate
SiO2
#HFMC17
Scale Build-up in Washer Disinfectors
Over exposure to Acid / Silicate
• Some Common Problems / Hard Water Elements
#HFMC17
Can be result from old and or damaged piping , inproper Material in RO Supply
Metal Ions• Some Common Problems / Metal Ions
Poor Quality Supply in Lines / Building Works
Plating from other less noble metal instrument
#HFMC17
.
Final Rinse Water – Washer Disinfectors (as per Section 7.2.3.1, AS/NZS 4187:2014)
100
AS/NZ4187:2014
#HFMC17
.Steam Generator Feedwater and Stream Quality – Steam Sterilizers (Table B.1 and Table B.2)
AS/NZ4187:2014
#HFMC17
• AS/NZS 4187:2014 Water Quality Testing
#HFMC17
#HFMC17
• Purification Methods
Water Type Characteristic
Potable Drinking water that normally contains both ionic & organic impurities
Softened Removal of calcium & magnesium
Deionized Removal of ionic impurities, but not all organic contaminates
Reverse Osmosis Removal of nearly all ionic & organic impurities
#HFMC17
Deionized Water
Tap Water
Control
• Purification Methods
#HFMC17
• Purification Methods
#HFMC17
Installations in the past
• Purification Methods
#HFMC17
Installations now and in the future
• Purification Methods
#HFMC17 21
• Purification Methods
#HFMC17
Purification to Distribution Loop
#HFMC17
One of the most important parts of the pure water system is the design of the ring main. We need to ensure that the system is built to ensure the consistent quality of water required.
Some key considerations:
• Turbulence flow by pump to retard the biofilm development• Velocity Maintenance in Return Line• Tank Turn Over – Volume Produced• Monitoring & Data logging of the process parameters• No Dead Legs
The Ring MainProduct Water Distribution Loop
#HFMC17
The Ring Main and Distribution Loop
Example product water capacity:
Six 86-Series Washer-Disinfectors and Five GSS67H Sterilizer Redundancy / Failure ?
If unit produced 500Ltr Hr 300Ltr Storage
240Ltr
100 Ltr
#HFMC17
Getinge Australia recommend the following materials to be used for RO ring mains:
• Georg Fischer Infrared welded Polypropylene Homopolymer [PPH-IR] piping
• Georg Fischer Type 519 Diaphragm Valves
• Georg Fischer PROGREF check valves
• ESP Sanitary Sampling Ports/Valves
• PNN Series Hydrophilic Nylon 0.2 Micron Membrane Filters (for advanced bacterial and endotoxin removal within circulating ring main product water).
• Big Blue carbon and particle filter set on feed water line (depending on water quality)
The Ring Main Product Water Distribution Loop
#HFMC17
• Summary Water
#HFMC17
• Summary
•Water for cleaning maybe of lesser quality only if
contaminant levels are not significant.
•If water quality is poor, then purifying method(s) should
be implemented.
•Water used for the final rinse of instruments and steam
sterilization should be of best quality e.g. RO
•For the longevity/integrity of your instruments and
equipment know your water/ steam quality and test it
regularly.