Post on 30-Jan-2018
VISION
Hersteller:EMCO MAIER Gesellschaft m.b.H.- P.O.Box 131- A-5400 Hallein/Austria- Tel.(06245) 891-0 Fax (06245) 86965
FANUC 0 - T / 21 - TDrehenTurningTournageTornear
Ausgabe 2002
Ref. Nr.: VS 9972
Fanuc 0-T / 21-T
TRAINING industrial training systems
INHALTSVERZEICHNIS
Folie Nr.
1, 1a23
4
56789
10111213141516
1718192021222324
25262728293031
Thema
Steuerungslayout Fanuc 0 - T, 21 - TBezugspunkte (M,A,W,R) und Koordinatensystem - GrundbildBezugspunkte am Werkzeugsystem (N,T,P); DarstellungReferenzieren.Bezugspunkte: Symbole und Kurzzeichen
Nullpunktverschiebung (NPV) Offset - GrundbildG92 Koordinatensystem setzen - GrundbildKombination Offset und G92 - GrundbildKoordinatensystem zu NPV-DarstellungWerkzeugkorrektur-Daten
G00 EilgangG01 LinearinterpolationG02 Kreisinterpolation im UhrzeigersinnG03 Kreisinterpolation im GegenuhrzeigersinnKreisinterpolation mit Mittelpunktskoordinaten I, KEinfügen von Radien "R" und Fasen "C"G04 Verweilzeit
G10 Programmierung WerkzeugkorrekturenG20 Längsdrehzyklus, AbsolutwertprogrammierungG20 Längsdrehzyklus, InkrementalwertprogrammierungG20 Längsdrehzyklus konischG21 Gewindeschneidzyklus zylindrischG21 Gewindeschneidzyklus konischG24 Plandrehzyklus zylindrischG24 Plandrehzyklus konisch
G28 Referenzpunkt anfahrenG33 Gewindeschneiden im EinzelsatzG34 Gewindeschneiden im Einzelsatz, Steigung zunehmendG34 Gewindeschneiden im Einzelsatz, Steigung abnehmendG41, G42 Schneidenradiuskompensation (SRK) - PrinzipG41, G42 Schneidenradiuskompensation (SRK) - RichtungG40, G41, G42 Anwahl / Abwahl SRK im Programm
Fanuc 0-T / 21-T
TRAINING industrial training systems
Folie Nr.
32333435363738
394041
424344
45464748
49
505152
Thema
G72 Schlichtzyklus KonturG73 Längsdrehzyklus KonturG74 Plandrehzyklus KonturG75 Zyklus MusterwiederholungG76 Zyklus TieflochbohrenG76 Einstechzyklus Z-AchseG77 Einstechzyklus X-Achse
G78 Mehrfach-GewindeschneidzyklusG78 Mehrfach-GewindeschneidzyklusG78 Mehrfach-Gewindeschneidzyklus
G83 BohrzyklusG84 GewindebohrzyklusG85 Ausreibbohrzyklus
G90 AbsolutwertprogrammierungG91 Inkrementalwertprogrammierung - GrundbildG91 Werkzeug und KoordinatenG98, G99 Rückzug auf Startebene, Rückzugebene
M98, M99 Unterprogrammtechnik
Konturzug GeradeKonturzug 2-PunkteKonturzug 3-Punkte
INHALTSVERZEICHNIS
Fanuc 0-T / 21-T
TRAINING industrial training systems
Slide No.
1, 1a23
4
56789
10111213141516
1718192021222324
25262728293031
Subject
Layout Fanuc 0 - T, 21 - TReference points (M,A,W,R) and coordinate systemReference points of toolsystem (N,T,P); approaching referencepointSymbols and signs of reference points
Zero shift offsetG92 Coordinate system settingCombination zero offset and G92Coordinate system to zero shift presentationTool offsets
G00 Rapid traverseG01 Linear interpolationG02 Circular interpolation, clockwiseG03 Circular interpolation, counter-clockwiseCircular interpolation with parameters I, KInsertion of radii "R" and chamfers "C"G04 Dwell
G10 Programming of tool offsetsG20 Longitudinal turning cycle, absolute programmingG20 Longitudinal turning cycle, incremental programmingG20 Longitudinal turning cycle, conicalG21 Thread cutting cycle, cylindricalG21 Thread cutting cycle, conicalG24 Face turning cycle, cylindricalG24 Face turning cycle, conical
G28 Return to reference pointG33 Thread cutting, constant leadG34 Thread cutting, linear lead increaseG34 Thread cutting, linear lead decreaseG41, G42 Cutter radius compensation (CRC) - principleG41, G42 Cutter radius compensation (CRC)G40, G41, G42 Selection / cancellation of CRC
TABLE OF CONTENTS
Fanuc 0-T / 21-T
TRAINING industrial training systems
Slide No.
32333435363738
394041
424344
45464748
49
505152
Subject
G72 Finishing cycleG73 Stock removal in turningG74 Stock removal in facingG75 Pattern repeatingG76 Deep hole drilling cycleG76 Grooving cycle in Z-axisG77 Grooving cycle in X-axis
G78 Multiple threading cycleG78 Multiple threading cycleG78 Multiple threading cycle
G83 Drilling cycleG84 Tapping cycleG85 Reaming cycle
G90 Absolute programmingG91 Incremental programmingG91 Tool and coordinate systemG98, G99 Return to initial, withdrawal plane
M98, M99 Subroutine technics
Blueprint programming:Linear element2-point cycle3-point cycle
TABLE OF CONTENTS
Fanuc 0-T / 21-T
TRAINING industrial training systems
Thèmes
Pupitre de commande Fanuc 0 - T, 21 - TPoints de référence (M,A,W,R) et systéme de coordonnées - Image debasePoints de référence d´outillage (N,T,P); accostage du point deréférence.Symboles graphiques des points de référence
Décalage d´origine (PSO) - Image de baseG92 poser le systéme de coordonnées - Image de baseCombinaison décalage d´origine et G92 - Image de baseSystéme de coordonnées pour présenter la décalage d´origineCorrecteur d´outils
G00 Vitesse rapideG01 Interpolation linéaireG02 Interpolation circulaire en sens horaireG03 Interpolation circulaire en sens antihoraireInterpolation circulaire avec paramètres d´interpolation I, KInserrer des rayons "R" et chanfreins "C"G04 Temporisation
G10 Programmation correcteur d´outilG20 Cycle de tournage longitudinal, valeurs absoluesG20 Cycle de tournage longitudinal, valeurs incrémentiellesG20 Cycle de tournage longitudinal, coniqueG21 Cycle de filetage cylindriqueG21 Cycle de filetage coniqueG24 Cycle de tournage facial, cylindriqueG24 Cycle de tournage facial, conique
G28 Accostage du point de référenceG33 Filetage, pas constantG34 Filetage, pas croissant linéairementG34 Filetage, pas décroissant linéairementG41, G42 Compensation du rayon de plaquette (CRP) - principeG41, G42 Compensation du rayon de plaquetteG40, G41, G42 Sélection / annulation CRP dans le programme
TransparentNr.
1, 1a2
3
4
56789
10111213141516
1718192021222324
25262728293031
TABLE DE MATIERES
Fanuc 0-T / 21-T
TRAINING industrial training systems
TABLE DE MATIERES
Thèmes
G72 Cycle de finition contourG73 Cycle de tournage longitudinal contourG74 Cycle de tournage facial contourG75 Cycle de repetition contourG76 Cycle de percage profondG76 Cycle de plongée axe ZG77 Cycle de plongée axe X
G78 Cycle de filetage multipleG78 Cycle de filetage multipleG78 Cycle de filetage multiple
G83 Cycle de percageG84 Cycle de taraudageG85 Cycle d´alesage
G90 Programmation en valeurs absoluesG91 Programmation en valeurs incrementielles - Image de baseG91 Outil et systéme de coordonnéesG98, G99 Retrait au plan de départ, au plan de référence
M98, M99 Technique des sous-programmes
Contour "droite"Contour "ligne à 2 points"Contour "ligne à 3 points"
TransparentNr.
32333435363738
394041
424344
45464748
49
505152
Fanuc 0-T / 21-T
TRAINING industrial training systems
CONTENIDO
Tema
Pupitre de mando Fanuc 0 - T, 21 - TPuntos de referencia (M,A,W,R) y sistema de coordenadas -Dibujo básicoPuntos de referencia en el sistema de herramientas (N,T,P);acercarse al puntos de referencia RSimbolos y abreviaturas para los puntos de referencia
Decalaje del origen - Dibujo básicoG92 Desplazamiento programado del sistema de coordenadas -Dibujo básicoCombinación de decalaje del origen con G92 - Dibujo básicoSistema de coordenadas para representación de decalajeDatos de corrección de herramienta
G00 Desplazamiento rápidoG01 Interpolación linealG02 Interpolación circular en sentido horarioG03 Interpolación circular en sentido antihorarioInterpolación circular con parámetros de interpolación I, KIntroducción de radios "R" y chaflanes "C"G04 Tiempo de parada
G10 Datos de correción de herramienta programadoG20 Ciclo de desbaste longitudinal, cotas absolutasG20 Ciclo de desbaste longitudinal, cotas incrementalesG20 Ciclo de desbaste longitudinal, rosca cónicaG21 Ciclo de roscado, rosca longitudinalG21 Ciclo de roscado, rosca cónicaG24 Ciclo de desbaste refrentar, rosca longitudinalG24 Ciclo de desbaste refrentar, rosca cónica
G28 Acercarse al punto de referencia RG33 Roscado con paso constanteG34 Roscado con paso creciente linealmenteG34 Roscado con paso decreciente linealmenteG41, G42 Compansación del radio de corte (CRC) - principeG41, G42 Compansación del radio de corte (CRC)G40, G41, G42 Selección / cancellación CRC en el programa
Hoja no.
1, 1a2
3
4
56
789
10111213141516
1718192021222324
25262728293031
Fanuc 0-T / 21-T
TRAINING industrial training systems
CONTENIDO
Tema
G72 Ciclo de acabado contornoG73 Ciclo de desbaste longitudinal contornoG74 Ciclo de desbaste refrentar contornoG75 Ciclo de repeticione del contornoG76 Ciclo de taladrado profundoG76 Ciclo de ranurado en ZG77 Ciclo de ranurado en X
G78 Ciclo de roscadoG78 Ciclo de roscadoG78 Ciclo de roscado
G83 Ciclo de taladradoG84 Ciclo de afiladoG85 Ciclo de escariado
G90 Programmación en coordonadas absolutasG91 Programmación en coordonadas incrementalesG91 Sistema de coordenadas para valores incrementalesG98, G99 Retroceso al plano de inicio / retroceso
M98, M99 Técnica de subprogramas
Contorno "recta"Contorno "sucesión de 2 puntos"Contorno "sucesión de 3 puntos"
Hoja no.
32333435363738
394041
424344
45464748
49
505152
TRAINING
Fanuc 0-T / 21-T
industrial training systems
SINUMERIK 810D/840D
GE Fanuc Series 21
ALTER
POS
INPUT
GRAPH
5 6
321
4
- .0
7 8 9
EOB/ CAN
PROG
MMC
CNCSYSTEM MESSAGE
X Z
M S T
O N G P( ) E Q
C YA B D ?
U W H V, J @
L# = * +
I K R F[ ] & SP
HELP
SHIFT
INSERT
DELETE
CUSTOMOFFSETSETTING
GE Fanuc Series 21
21-T
1a