Post on 26-Oct-2020
Muncie Power Products, Inc.
V130 SERIESOPEN CENTER SECTIONAL
DIRECTIONAL CONTROL VALVESPARTS LIST AND SERVICE MANUAL
V130 Assembly - Exploded View
H
G
E
D
E
B
L
G
A
B
C
F
I
C
F
G
JK
G
Item Description PageA Inlet Section 3
B Inlet Relief Valve 4
C Work Section 5
D Lever Handle 5
E Control Option 6-8
F Back-cap Options 9-15
G Work Port Relief Valve 16-18
H Pilot Operated Check Valve 19-20
I Mid-Section 21
J Outlet Section 22
K Power Beyond or Closed Center Options 23
N/A Seal Kits 24-25
L Stud Kits 26
Muncie Power Products, Inc.2
1
3
2
1
3
2
Item Description P/N
1 Steel plug with O-Ring, -16SAE (1⁵⁄₁₆"-12 UN) HHBP-16Z
2
Inlet with -16SAE (1⁵⁄₁₆"-12 UN) end port by -16SAE (1⁵⁄₁₆"-12 UN) top port, and relief valve set at 2,175 PSI (150 BAR) STANDARD INLET with STANDARD RELIEF VALVE (RV adjustment range 1,175 - 2,900 PSI; 81 - 200 BAR)
V130-A-GI-7SX-N-150
Inlet with -16SAE (1⁵⁄₁₆"-12 UN) end port by -16SAE (1⁵⁄₁₆"-12 UN) top port, and relief valve set at 3,045 PSI (210 BAR) WITH HIGH PRESSURE RELIEF VALVE (RV adjustment range 2,915 - 5,510 PSI; 201 - 380 BAR)
V130-A-GI-7SX-R-210
3 Inlet relief valve (See page 4 for relief valve information) N/A
Inlet NotesItem 1&3 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
Inlet Sections V130-A-GI-7SX-**** V130-A-GI-7SP-****
Kit Part NumberV130-A-GI-7SX-****, Inlet with Relief ValveV130-A-GI-7SP-****, Inlet with Pilot Operated Relief Valve
Kit Part NumberV130-A-GI-8SX-XXXX Inlet without Relief Valve
Item Description P/N1 Steel plug with O-Ring, -16SAE (1⁵⁄₁₆"-12 UN) HHBP-16Z
2 Inlet with -16SAE (1⁵⁄₁₆"-12 UN) end port by -16SAE (1⁵⁄₁₆"-12 UN) top port, and NO relief valve V130-A-GI-8SX-XXXX
3 Steel plug used in place of main relief valve (See page 4 for more information) V130-AB-X-XXX
Inlet NotesItem 1&3 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
1
3
2
1
3
2
V130-A-GI-8SX-XXXX
Muncie Power Products, Inc. 3
2
4
1
3
56
78
9
1011
12
34
21
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 21.95mm) N/A 12 Back-up ring, parbak 8-020 N/A 1
3 O-Ring, NBR, 70°Sh, 0.09" x 0.92" (2.40 x 23.30mm) N/A 1
4 Main RV cartridge body N/A 1
5 Main RV poppet N/A 1
6
Main RV spring, code “B” (Adj from: 145 - 1,160 PSI (10 - 80 BAR) V080130-AB-BSPG
1Main RV spring, code “N” (Adj from: 1,175 - 2,900 PSI (81 - 200 BAR) V080130-AB-NSPG
Main RV spring, code “R” (Adj from: 2,915 - 5,510 PSI (201 - 380 BAR) V080130-AB-RSPG
Main RV spring, code “F” (Adj from: 145 - 5,510 PSI (10 - 380 BAR) *Only for 7SP option N/A
7 Main RV spring seat N/A 1
8 O-Ring, NPB, 70°Sh, 0.07" x 0.55" (1.78 x 14.00mm) N/A 1
9 O-Ring, NPB, 70°Sh, 0.07" x 0.80" (1.78 x 20.35mm) N/A 1
10 Main RV cap N/A 1
11 Main RV adjusting screw N/A 1
12 Jam nut N/A 1
Inlet Relief Valve NotesItem 4 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
Item 10 Torque to 30 ± 2.5 ft.lb. (40 ± 3 Nm)
Item 12 Torque to 11 ± 1.5 ft.lb. (15 ± 2 Nm)
Inlet Relief Valve V130-AB-****
Part NumberV130-AB-****Inlet Relief Valve
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.07" x 0.86" (1.78 x 21.95mm) N/A 12 Back-up ring, parbak 8-020 N/A 1
3 O-Ring, NBR, 70°Sh, 0.09" x 0.92" (2.40 x 23.30mm) N/A 1
4 Main RV plug steel plug N/A 1
Inlet Plug NotesItem 4 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
V130-AB-X-XXX
2
4
1
3
56
78
9
1011
12
34
21
Part NumberV130-AB-X-XXXInlet Plug
Relief Valve OptionsPart Number Cartirdge Valve Set Point Cartridge Valve Adj RangeV130-AB-B080 Set @ 1,160 PSI (80 BAR) Adj from: 145 - 1,160 PSI (10 - 80 BAR)V130-AB-N150 Set @ 2,175 PSI (150 BAR) Adj from: 1,175 - 2,900 PSI (81 - 200 BAR)V130-AB-R210 Set @ 3,000 PSI (210 BAR) Adj from: 2,915 - 5,510 PSI (201 - 380 BAR)
Muncie Power Products, Inc.4
4
3
21
1
Work Section
Item Description P/N1 Back-cap option (See pages 9-15 for more information) N/A
2Work section casting machined for work port options with -12SAE ports N/A
Work section casting machined for work port options with -16SAE ports N/A
3
3P3W, single acting cylinder spool, pressure out “B” port V130-SPL-AB
3P4W, single acting cylinder spool V130-SPL-AC
3P4W, bi-rotational motor spool (work ports connected to tank in neutral) V130-SPL-AJ
4P4W, double acting cylinder with 4th position float spool V130-SPL-AM
4 Control option (See pages 6 - 8 for more information) N/A
Item Description P/N
18.25in (210mm) lever handle (standard option) VLVH-01A-2108.27in (219mm) lever handle (has lens cap) VLVH-02A-219
Valve Handle KitVLVH-0*A-***
Muncie Power Products, Inc. 5
2
1
5
6
3
4
4
3
2
1
56
7
9
8
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Pivot pin N/A 1
3 Rubber dust boot N/A 1
4 Handle receiver & spool connector N/A 1
5 Lever cap control housing N/A 1
6 Spacer bushing for control options N/A 1
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Control Options V130-CT-AA
Kit Part NumberV130-CT-AAStandard Lever Cap
Item Description P/N Qty.1 Screw, M5 x 25 gr. 8.8 (UNI 5931) N/A 42 Pivot pin N/A 1
3 Rubber dust boot N/A 1
4 Handle receiver & spool connector N/A 1
5 Lever cap control housing N/A 1
6 Spacer plate used for 4 position spools N/A 1
7 O-Ring, NBR, 90°Sh, 0.139" x 0.796" (3.53 x 20.22mm) N/A 1
8 Spacer bushing for control option N/A 1
9 O-Ring, NBR, 70°Sh, 0.070" x 0.864" (1.78 x 21.95mm) N/A 1
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Kit Part NumberV130-CT-ABLever Cap for Float Spool (4th Position Detent)
V130-CT-AB
2
1
5
6
3
4
4
3
2
1
56
7
9
8
Muncie Power Products, Inc.6
2
1
3
1
2
5
4
12
7
6
3
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Spool cover for control option N/A 1
3 Spacer bushing for control options N/A 1
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Control Options V130-CT-AE
Kit Part NumberV130-CT-AESpool Cover for Back-cap Control
Item Description P/N Qty.1 Screw, M5 x 10 gr. 8.8 (UNI 5931) N/A 42 Control plate and spool O-Ring retainer N/A 1
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Kit Part NumberV130-CT-AJSpool Eye Only for Direct Connection
V130-CT-AJ
2
1
3
1
2
5
4
12
7
6
3
Item Description P/N Qty.1 Screw, M5 x 25 gr. 8.8 (UNI 5931) N/A 42 Washer, 5mm diameter N/A 4
3 Control plate N/A 1
4 Spacer plate used for 4 position spools N/A 1
5 O-Ring, NBR, 70°Sh, 0.070" x 0.864" (1.78 x 21.95mm) N/A 1
6 Spacer bushing N/A 1
7 O-ring, NBR, 90°Sh, 0.103" x 0.703" (2.62 x 17.86mm) N/A 1
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Kit Part NumberV130-CT-AKSpool Eye Only for Float Spool (4th Position Detent)
V130-CT-AK
2
1
3
1
2
5
4
12
7
6
3
Muncie Power Products, Inc. 7
Back side of work section
Front side of work section
3
5
7
13
4
89
10
2
1
6
98
2
10
4
Control Options V130-CT-BG
Kit Part NumberV130-CT-BGLow Pressure, Dual Sided, Hydraulic Control
Item Description P/N Qty.1 Screw, M5 x 65 gr. 8.8 (UNI 5931) N/A 82 Washer, 5mm diameter N/A 8
3 Pressure gauge port plug w/O-Ring, ⅛" GAS thread N/A 2
4 Hydraulic control caps N/A 2
5 Back-cap spool connector N/A 1
6 Washer for spring compressing N/A 2
7 Positioning spring N/A 1
8 O-Ring, NBR, 70°Sh, 0.070" x 1.176" (1.78 x 29.87mm) N/A 2
9 Spacer bushing N/A 2
10 O-Ring, NBR, 70°Sh, 0.070" x 0.864" (1.78 x 21.95mm) N/A 2
Control NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 3 Torque to 7.4 ± 0.4 ft.lb. (10 ± 0.5 Nm)
Item 5
Clean the threads on item 5 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 5 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool
and apply 1 drop of Loctite 242. Be sure to avoid applying Loctite to the O-Ring area.
Torque item 5 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Muncie Power Products, Inc.8
1
2
6
5
3
4
Back-cap Positioners V130-BC-01
Kit Part NumberV130-BC-01Standard 3 Position, Spring Return
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Back-cap housing for standard spring return N/A 1
3 Back-cap spool connector for standard spring return N/A 1
4 Standard washer for spring compressing N/A 2
5 Standard positioning spring N/A 1
6 Standard spacer bushing N/A 1
Back-cap NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 3
Clean the threads on item 3 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 3 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool
and apply 1 drop of Loctite 242. Be sure to avoid applying Loctite to the O-Ring area.
Torque item 3 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Item 5 Apply multi-purpose grease to the spring prior to assembly
Muncie Power Products, Inc. 9
5
4
8
9
7
6
3
21
Back-cap Positioners V130-BC-06 V130-BC-07
Kit Part NumberV130-BC-06, Detent Spool “IN” (Position 1) Spring Spool “OUT” (Position 2)V130-BC-07, Spring Spool “IN” (Position 1) Detent Spool “OUT” (Position 2)
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Back-cap mounting plate N/A 1
3Back-cap housing for detent “IN”, spring “OUT”, option 06 N/A 1
Back-cap housing for detent “OUT”, spring “IN”, option 07 N/A 1
4 Detent ball N/A 2
5 Detent spring N/A 1
6Back-cap spool connector for detent “IN”, spring “OUT”, option 06 N/A 1
Back-cap spool connector for detent “OUT”, spring “IN”, option 07 N/A 1
7 Standard washer for spring compressing N/A 2
8 Standard positioning spring N/A 1
9 Standard spacer bushing N/A 1
Back-cap NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 4&5 Generously apply multi-purpose grease to the spring and detent balls prior to assembly to aid in the assembly process
Item 6
Clean the threads on item 6 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool and apply 1 drop of Loctite 242.
Be sure to avoid applying Loctite to the O-Ring area.
Torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Item 8 Apply multi-purpose grease to the spring prior to assembly
Muncie Power Products, Inc.10
4
5
6
7
3
2
1
Back-cap Positioners V130-BC-08
Kit Part NumberV130-BC-083 Position Detent
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Back-cap mounting plate N/A 1
3 Back-cap housing for 3 position detent N/A 1
4 Detent ball N/A 2
5 Detent spring N/A 1
6 Back-cap spool connector for 3 position detent N/A 1
7 Standard spacer bushing N/A 1
Back-cap NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 4&5 Generously apply multi-purpose grease to the spring and detent balls prior to assembly to aid in the assembly process
Item 6
Clean the threads on item 6 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool, and apply 1 drop of Loctite 242.
Be sure to avoid applying Loctite to the O-Ring area.
Torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Muncie Power Products, Inc. 11
5
4
9
8
76
3
2
1
Back-cap Positioners V130-BC-12
Kit Part NumberV130-BC-123 Position, Spring Return with 4th Position Detent
Item Description P/N Qty.1 Screw, M5 x 12 gr. 8.8 (UNI 5931) N/A 42 Back-cap mounting plate N/A 1
3 Back-cap housing for float spool (4th position detent) N/A 1
4 Detent ball N/A 2
5 Detent spring N/A 1
6 Back-cap spool connector for float spool (4th position detent) N/A 1
7 Standard washer for spring compressing N/A 2
8 Standard positioning spring N/A 1
9 Standard spacer bushing N/A 1
Back-cap NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 4&5 Generously apply multi-purpose grease to the spring and detent balls prior to assembly to aid in the assembly process
Item 6
Clean the threads on item 6 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool, and apply 1 drop of Loctite 242.
Be sure to avoid applying Loctite to the O-Ring area.
Torque item 6 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Item 8 Apply multi-purpose grease to the spring prior to assembly
Muncie Power Products, Inc.12
2
3
45
67
13
14
11
10
9
8
1
12
Back-cap Positioners V130-BC-33
Kit Part NumberV130-BC-33Pneumatic Shift, (Use w/Control Type AA, AE or AJ)
Item Description P/N Qty.1 Screw, M5 x 100 gr. 8.8 (UNI 5931) N/A 42 Washer, 5mm ID x 10MM OD N/A 4
3 Pneumatic control cylinder housing N/A 1
4 Lock nut, M8 thread N/A 1
5 Washer, 8mm ID x 14mm OD N/A 1
6 Piston for pneumatic control N/A 1
7 O-Ring, NBR, 70°Sh, 0.070" x 1.36" (1.78 x 34.65mm) N/A 1
8 Back-cap housing for pneumatic control N/A 1
9 O-Ring, NBR, 90°Sh, 0.10" x 0.49" (2.62 x 12.37mm) N/A 1
10 Piston rod for pneumatic cylinder N/A 1
11 Back-cap spool connector for pneumatic control N/A 1
12 Standard washer for spring compressing N/A 2
13 Positioning spring for pneumatic control (proportional or on/off) N/A 1
14 Standard spacer bushing N/A 1
Back-cap NotesItem 1 Torque to 2.2 ± 0.15 ft.lb. (3 ± 0.2 Nm)
Item 4 Torque to 14.7 ± 2.2 ft.lb. (20 ± 3 Nm)
Item 6 Lightly apply multi-purpose grease to the piston prior to assembly
Item 11
Clean the threads on item 11 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 11 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool and apply 1 drop of Loctite 242.
Be sure to avoid applying Loctite to the O-Ring area.
Torque item 11 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Item 13 Apply multi-purpose grease to the spring prior to assembly
Muncie Power Products, Inc. 13
9
10
8
7
6
45
3
2
1
Back-cap Positioners V130-BC-41
Kit Part NumberV130-BC-41 Friction Detent
Item Description P/N Qty.1 Screw, M5 x 60 gr. 8.8 (UNI 5931) N/A 42 Lock Washer, 5mm ID N/A 4
3 Back-cap housing for friction detent N/A 1
4 Back-cap spool connector for friction detent N/A 1
5 Standard spacer bushing N/A 1
6 Lock nut, 8M thread N/A 1
7 Detent housing for friction detent N/A 1
8 Detent spring for friction detent N/A 1
9 Adjustable set screw for friction detent (M10 x 45mm) N/A 1
10 Jam nut for friction detent (M10 thread) N/A 1
Back-cap NotesItem 1 Torque to 4.4 ± 0.3 ft.lb. (6 ± 0.4 Nm)
Item 4
Clean the threads on item 4 and in the spool seat with a degreasing product.
For parallel and single spools
Apply 2 drops of Loctite 242 and torque item 4 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool
For series and series-parallel spools
Assemble the O-Ring (90°Sh, 0.070" x 0.426") supplied with the spool,
and apply 1 drop of Loctite 242. Be sure to avoid applying Loctite to the O-Ring area.
Torque item 4 to 30 ± 1.5 ft.lb. (40 ± 2 Nm).
Be sure not to scratch or damage the spool.
Item 8 Apply multi-purpose grease to the spring prior to assembly
Item 10 Torque to 14.7 ± 2.2 ft.lb. (20 ± 3 Nm)
Muncie Power Products, Inc.14
Cartridge Valves
4
5
1
2
3
6
Item Description Page Qty.1 V130-W04-XXXX 16 1 or 2
2 V130-WCX-XXXX 16 1 or 2
3 V130-W30-**** (See page 16 for RV setting options) 17 1 or 2
4 V130-W66-**** (See page 17 for Pilot operated RV + AC for setting options) 16 1 or 2
5 V130-W33-**** (See page 18 for AC setting options) 18 1 or 2
6 V130-CHK-XXXX 18 1
Cartridge NotesItem 1-5 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
Cartridge Valves
Muncie Power Products, Inc. 15
24 5 631
1 2 3 4
2 3 5 7 10 11 7 1413128918641
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 18.77mm) N/A 22 O-Ring, NBR, 70°Sh, 0.09" x 0.95" (2.40 x 23.30mm) N/A 13 Relief valve body N/A 14 Poppet seal N/A 15 Guide spring N/A 16 Slider spring N/A 17 O-Ring retainer N/A 18 O-Ring, NBR, 70°Sh, 0.07" x 0.25" (1.78 x 6.33mm) N/A 19 Anti-cavitation valve dart N/A 1
10 Pilot operated relief valve body N/A 111 Relief valve dart N/A 112 Pilot operated RV “F” spring adj. from 725 - 5,800 PSI (50 - 400 BAR) N/A 113 O-Ring, NBR, 70°Sh, 0.07" x 0.43" (1.78 x 10.82mm) N/A 114 O-Ring, NBR, 70°Sh, 0.07" x 0.49" (1.78 x 12.42mm) N/A 115 Pilot operated relief valve plug N/A 1
16 Relief valve adjustment screw N/A 1
17 Work port RV jam nut N/A 1
Relief Valve NotesItem 3 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
Item 10 Torque to 52 ± 5 ft.lb. (38 ± 3 Nm)Item 15 Torque to 15 ± 2 ft.lb. (20 ± 3 Nm)Item 17 Torque to 20 ± 3 ft.lb. (15 ± 2 Nm)
Cartridge Valves V130-W04-XXXXPart NumberV130-W04-XXXXWork Port Anti-Cavitation Valve
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.09" x 0.95" (2.40 x 23.30mm) N/A 12 Back-up ring, parbak 8-018 N/A 13 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 18.77mm) N/A 14 Work port option plug N/A 1
Relief Valve NotesItem 1 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
Part NumberV130-WCX-XXXXBlanking Plug
Part NumberV130-W66-F125Work Port RV + AC (Full Flow Pilot Operated)
24 5 631
1 2 3 4
2 3 5 7 10 11 7 14131289186412 3 5 7 8 11 14 17161513121019641
Item Description P/N Qty.1 Anti-cavitation check ball spacer N/A 12 Anti-cavitation check ball, 5⁄16 " diameter, S2 class A N/A 13 O-Ring, NBR, 70°Sh, 0.09" x 0.95" (2.40 x 23.30mm) N/A 14 Back-up ring, parbak 8-018 N/A 15 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 18.77mm) N/A 16 Anti-cavitation valve body N/A 1
Relief Valve NotesItem 1 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
V130-WCX-XXXX
V130-W66-F125
Muncie Power Products, Inc.16
2 3 4 7 9 10 12 13118651
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.09 " x 0.95" (2.40 x 23.30mm) N/A 12 Back-up ring, parbak 8-018 N/A 1
3 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 18.77mm) N/A 1
4 Work port relief valve cartridge body N/A 1
5 Relief valve cone N/A 1
6
Work port RV spring , code “B” (Adj from: 435 - 1,160 PSI (30 - 80 BAR)) V130-W30-BSPG
1Work port RV spring, code “N” (Adj from: 1,175 - 2,900 PSI (81 - 200 BAR)) V130-W30-NSPG
Work port RV spring, code “R” (Adj from: 2,915 - 5,075 PSI (201 - 350 BAR)) V130-W30-RSPG
7 O-Ring, NBR, 70°Sh, 0.07" x 0.36" (1.78 x 9.25mm) N/A 1
8 Spring seat for work port relief valve N/A 1
9 Washer for work port relief valve N/A 1
10 O-Ring, NBR, 70°Sh, 0.07" x 0.61" (1.78 x 15.60mm) N/A 1
11 Plug for work port relief valve N/A 1
12 Work port RV jam nut N/A 1
13 Work port relief valve adjusting screw N/A 1
Work Section NotesItem 4 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
Item 11 Torque to 15 ± 2 ft.lb. (20 ± 3 Nm)
Item 12 Torque to 11 ± 1.5 ft.lb. (15 ± 2 Nm)
Cartridge Valves V130-W30-****
Part NumberV130-W30-****Work Port Relief Valve
Work Port Relief OptionsPart Number Cartirdge Valve Set Point Cartridge Valve Adj RangeV130-W30-B070 Set @ 1,015 PSI (70 BAR) Adj Range: 435 - 1,160 PSI (30 - 80 BAR)V130-W30-N125 Set @ 1,812 PSI (125 BAR)
Adj Range: 1,175 - 2,900 PSI (81 - 200 BAR)V130-W30-N150 Set @ 2,175 PSI (150 BAR)V130-W30-N170 Set @ 2,465 PSI (170 BAR) V130-W30-R210 Set @ 3,045 PSI (210 BAR) Adj Range: 2,915 - 5,075 PSI (201 - 350 BAR)
Muncie Power Products, Inc. 17
6 7 131211109854321
1 2 3 4
Item Description P/N Qty.1 Anti-cavitation valve N/A 12 Relief valve cone N/A 1
3
Work port RV spring, code “B” (Adj range: 435 - 1,160 PSI (30 - 80 BAR)) V130-W30-BSPG
1Work port RV spring, code “N” (Adj range: 1,175 - 2,900 PSI (81 - 200 BAR)) V130-W30-NSPG
Work port RV spring, code “R” (Adj range: 2,915 - 5,075 PSI (201 - 350 BAR)) V130-W30-RSPG
4 Work port relief valve adjusting screw, anti-cavitation + RV version N/A 1
5 O-Ring, NBR, 70°Sh, 0.07" x 0.74" (1.78 x 18.77mm) N/A 1
6 Back-up ring, parbak 8-018 N/A 1
7 O-Ring, NBR, 70°Sh, 0.09" x 0.95" (2.40 x 23.30mm) N/A 1
8 Work port relief valve cartridge body N/A 1
9 Anti-cavitation valve spring N/A 1
10 Washer for spring wire N/A 1
11 Spring wire N/A 1
12 O-Ring, NBR, 70°Sh, 0.07" x 0.86" (1.78 x 21.95mm) N/A 1
13 Plug for anti-cavitation valve N/A 1
Work Section NotesItem 8 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
Item 13 Torque to 52 ± 2.2 ft.lb. (38 ± 3 Nm)
Cartridge Valves V130-W33-****
Part NumberV130-W33-****Work Port Relief Valve & Anti-Cavitation Valve
Work Port Relief OptionsPart Number Cartirdge Valve Set Point Cartridge Valve Adj RangeV130-W33-B070 Set @ 1,015 PSI (70 BAR) Adj from: 435 - 1,160 PSI (30 - 80 BAR)V130-W33-N125 Set @ 1,812 PSI (125 BAR)
Adj from: 1,175 - 2,900 PSI (81 - 200 BAR) V130-W33-N150 Set @ 2,175 PSI (150 BAR)V130-W33-N170 Set @ 2,465 PSI (170 BAR)V080-W30-R210 Set @ 3,045 PSI (210 BAR) Adj from: 2,915 - 5,075 PSI (201 - 350 BAR)
6 7 131211109854321
1 2 3 4
Part NumberV130-CHK-XXXXWork Port Check Valve
V130-CHK-XXXX
Item Description P/N Qty.1 Plug for check valve N/A 12 O-Ring, NBR, 70°Sh, 0.07" x 0.787" (2.00 x 20.00mm) N/A 1
3 Spring for check valve N/A 1
4 Check valve N/A 1
Work Section NotesItem 1 Torque to 29.5 ± 2.2 ft.lb. (40 ± 3 Nm)
Muncie Power Products, Inc.18
P.O. Check Assemblies
Item Description P/N
1
P.O. check manifold assembly with check on 1 port and -10SAE ports V130-FM-W01-XXXX
P.O. check manifold assembly with check on 1 port and -12SAE ports V130-FX-W01-XXXX
P.O. check manifold assembly with check on 2 ports and -10SAE ports V130-FM-W03-XXXX
P.O. check manifold assembly with check on 2 ports and -12SAE ports V130-FX-W03-XXXX
2
Work section casting machined for work port options & P.O. checks with -8SAE ports, SINGLE ACTING CYLINDER SPOOL on B port, exposed spool eye, standard spring return V130ABAJ01FM025
Work section casting machined for work port options & P.O. checks with -8SAE ports, DOUBLE ACTING CYLINDER SPOOL on B port, exposed spool eye, standard spring return V130ACAJ01FM025
Work section casting machined for work port options & P.O. checks with -8SAE ports, DOUBLE ACTING CYLINDER SPOOL on B port, exposed spool eye, standard spring return V130AJAJ01FM025
Work section casting machined for work port options & P.O. checks with -8SAE ports, 4TH POSITION FLOAT SPOOL , exposed spool eye, standard spring return with 4th position detent V130AMAK12FM025
1
2
Assembled Work SectionPre-Arranged for P.O. Checks and Work Port Options
Muncie Power Products, Inc. 19
9
7
4
1
8
10
117
5
32
6 5
32
6
4
1
5
43
12
6
78
2
1011
9
1213
Item Description P/N Qty.1 Plug used with insert plug for single sided P.O. check option N/A 12 Back-up ring, parbak 8-016 N/A 23 Insert plug for single-sided P.O. check option (replaces check valve) N/A 14 P.O. check manifold with -12SAE ports or -10SAE ports N/A 15 P.O. check valve mounting screw, M6 x 65mm, grade 8.8 N/A 86 O-Ring, NBR, 70°Sh, 0.01" x 1.30" (2.62 x 32.99mm) N/A 27 Pilot piston N/A 18 O-Ring, NBR, 70°Sh, 0.07" x 0.80" (1.78 x 20.35mm) N/A 19 Check valve body N/A 1
10 Check ball, 19⁄32" diameter, S2 class A N/A 111 P.O. check valve spring N/A 112 O-Ring, NBR, 70°Sh, 0.10" x 0.86" (2.62 x 21.89mm) N/A 113 Plug with spring seat used with check valve N/A 1
Work Section P.O. Check Assembly NotesItem 5 Torque to 7.4 ± 1.5 ft.lb. (10 ± 2 Nm)
Item 1&13 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)
P.O. Check Assemblies V130-FM-W01-XXXX V130-FX-W01-XXXX
Kit Part NumberV130-FM-W01-XXXX, Single P.O. Check w/-10 SAEV130-FX-W01-XXXX, Single P.O. Check w/-12 SAE
9
7
4
1
8
10
117
5
32
6 5
32
6
4
1
5
43
12
6
78
2
1011
9
1213
Item Description P/N Qty.1 Plug with spring seat used with check valve N/A 22 O-Ring, NBR, 70°Sh, 0.10" x 0.86" (2.62 x 21.89mm) N/A 23 P.O. check valve spring N/A 24 Check ball, 19⁄32" diameter, S2 class A N/A 25 Check valve body N/A 26 Back-up ring, parbak 8-016 N/A 27 O-Ring, NBR, 70°Sh, 0.07" x 0.80" (1.78 x 20.35mm) N/A 28 P.O. check manifold with -12SAE ports or -10SAE ports N/A 19 P.O. check valve mounting screw M6 x 65mm, grade 8.8 N/A 8
10 O-Ring, NBR, 70°Sh, 0.01" x 1.30" (2.62 x 32.99mm) N/A 211 Pilot piston N/A 1
Work Section P.O. Check Assembly NotesItem 1 Torque to 60 ± 3.7 ft.lb. (80 ± 5 Nm)Item 9 Torque to 7.4 ± 1.5 ft.lb. (10 ± 2 Nm)
Kit Part NumberV130-FM-W03-XXXX, Double P.O. Check w/-10 SAEV130-FX-W03-XXXX, Double P.O. Check w/-12 SAE
V130-FM-W03-XXXXV130-FX-W03-XXXX
Muncie Power Products, Inc.20
2
5
4
1
3
4
3
2
1
Mid-Sections V130-B-GI-E53-N150
Kit Part NumberV130-B-GI-E53-N150Combined Flow Mid-inlet w/RV
Item Description P/N Qty.1 Steel plug with O-Ring, -16SAE (15⁄16 "-12 UN) HHBP-16Z 12 Combined flow mid-inlet casting with -16SAE (15⁄16"-14 UN) top and side ports N/A 1
3 V130-GSK-OUT (See page 25 for more information) N/A 1
4 ½" GAS plug assembly with O-Ring, NBR, 70°Sh, 0.10" x 0.86" (2.62 x 18.72mm) N/A 1
5 See page 4 for more information N/A 1
Mid-Section NotesItem 1 Torque to 60 ± 3.5 ft.lb. (80 ± 5 Nm)
Item 4 Torque to 30 ± 2.2 ft.lb. (40 ± 3 Nm)
Item 5 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
Item Description P/N Qty.1 Steel plug with O-Ring, -16SAE (15⁄16"-12 UN) HHBP-16Z 12 ½” GAS plug assembly with O-Ring, NBR, 70°Sh, 0.10" x 0.74" (2.62 x 18.72mm) N/A 2
3 Split flow mid-outlet casting with -16SAE (15⁄16"-12 UN) side ports, option E51 N/A 1
4 V130-GSK-OUT (See page 25 for seal kit information) N/A 1
Mid-Section NotesItem 1 Torque to 60 ± 3.5 ft.lb. (80 ± 5 Nm)
Item 2 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
Kit Part NumberV130-B-GI-E51-XXXX, Split Flow Mid-outlet
V130-B-GI-E51-XXXX
Muncie Power Products, Inc. 21
2
4
2
3
1
2
Outlets V130-C-GI-3DX-XXXStandard Outlet
V130-C-FY-6DX-XXXOutlet w/HPCO
(Power Beyond)
V130-C-FY-16DX-XXXOutlet w/Closed
Center Plug
Item Description P/N1 Steel plug with O-Ring, -16SAE (15⁄16"-12 UN), (Only used with standard outlet, 3DX option) HHBP-16Z
2 Outlet casting with -12SAE (15⁄16"-12 UN) top and end ports {STANDARD OUTLET} N/A
3 Power beyond plug (See page 23 for more information) V130-C-PBS-02
4 Closed center plug (See page 23 for more information) V130-C-CCP-02
Muncie Power Products, Inc.22
4
3
2
1
12
3
4
Outlets V130-C-PBS-02
V130-C-CCP-02
Kit Part NumberV130-C-PBS-02 HPCO (Power Beyond Plug)
Item Description P/N Qty.1 -12SAE power beyond plug with -16SAE port V130-C-PBS-02 12 O-Ring, NBR, 70°Sh, 0.12" x 1.17" (2.95 x 29.74mm) N/A 1
3 Back-up ring parbak 8-118 N/A 1
4 O-Ring, NBR, 70°Sh, 0.07" x 0.80" (2.62 x 22.22mm) N/A 1
Outlet NotesItem 1 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
*V130-C-PBS-02 can be ordered separately from main assembly
Kit Part NumberV130-C-CCP-02Closed Center Plug
Item Description P/N Qty.1 -12SAE closed center plug with -16SAE port V130-C-CCP-02 12 O-Ring, NBR, 70°Sh, 0.12" x 1.17" (2.95 x 29.74mm) N/A 1
3 Back-up ring parbak 8-118 N/A 1
4 O-Ring, NBR, 70°Sh, 0.07" x 0.80" (2.62 x 22.22mm) N/A 1
Outlet NotesItem 1 Torque to 88 ± 6 ft.lb. (120 ± 8 Nm)
*V130-C-CCP-02 can be ordered separately from main assembly
Muncie Power Products, Inc. 23
1
3
45
21
3
2
1
3
1
2
Seal Kits V130-GSK-IN
V130-GSK-WS
Kit Part NumberV130-GSK-INInlet Seal Kit
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.07" x 0.86" (1.78 x 21.95mm) N/A 12 Back-up ring, parbak 8-020 N/A 1
3 O-Ring, NBR, 70°Sh, 0.09" x 0.92" (2.40 x 23.30mm) N/A 1
4 O-Ring, NBR, 70°Sh, 0.07" x 0.55" (1.78 x 14.00mm) N/A 1
5 O-Ring, NBR, 70°Sh, 0.07" x 0.80" (1.78 x 20.35mm) N/A 1
Kit Part NumberV130-GSK-WSWork Section Seal Kit
Item Description P/N Qty.1 O-Ring, NBR, 90°Sh, 0.14" x 0.80" (3.53 x 20.22mm) N/A 22 O-Ring, NBR, 70°Sh, 0.07" x 0.61" (1.78 x 15.60mm) N/A 4
3 O-Ring, NBR, 70°Sh, 0.08" x 0.79" (2.00 x 20.00mm) N/A 1
Muncie Power Products, Inc.24
1
1
Seal Kits V130-GSK-OUT
V130-GSK-OUT
Kit Part NumberV130-GSK-OUTOutlet Seal Kit
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.098" x 0.79" (2.50 x 20.00mm) N/A 4
Kit Part NumberV130-GSK-OUTOutlet Seal Kit
Item Description P/N Qty.1 O-Ring, NBR, 70°Sh, 0.098" x 0.79" (2.50 x 20.00mm) N/A 4
Muncie Power Products, Inc. 25
2
1
DIM "L"
Stud Kits
Item Description P/N Qty.1 Lock-Nut, M12 (UNI 7473) N/A 62 Tie Rod N/A 3
KIT INFOItem Description KIT P/N DIM “L” IN (mm)N/A Stud for 1 work section assembly V130-T01 5.6 (143)
N/A Stud for 2 work section assembly V130-T02 7.5 (191)
N/A Stud for 3 work section assembly V130-T03 9.4 (239)
N/A Stud for 4 work section assembly V130-T04 11.3 (287)
N/A Stud for 5 work section assembly V130-T05 13.2 (335)
N/A Stud for 6 work section assembly V130-T06 15.1 (383)
N/A Stud for 7 work section assembly V130-T07 17.0 (431)
N/A Stud for 8 work section assembly V130-T08 18.9 (479)
N/A Stud for 9 work section assembly V130-T09 20.7 (527)N/A Stud for 10 work section assembly V130-T10 22.6 (575)
Stud Kit Notes
Item 1&2 Torque to 52 ± 4 ft.lb. (70 ± 5 Nm)
Muncie Power Products, Inc.26
Muncie Power Products, Inc. 27
201 East Jackson Street • Muncie, Indiana 47305800-367-7867 • Fax 765-284-6991 • info@munciepower.com • www.munciepower.com
Specifications are subject to change without notice. Visit www.munciepower.com for warranties and literature. All rights reserved. © Muncie Power Products, Inc. (2014)A Member of the Interpump Group
SP14-02 (Rev. 02-18)