Post on 14-May-2018
www.smartomi.com support@smartomi.com 1
Accessories
User Manual
Wireless Headphone
Micro USB Cable
3.5mm Audio Cable
Please read the user manual before using the headphone and keep it in a safeplace for future reference.
www.smartomi.com support@smartomi.com 2
Product Introduction
Previous
Next
Play/Pause
Mic Power
USB PortLine In Jack
Volume-
Volume+
Headphone Functions
www.smartomi.com support@smartomi.com 3
Product Introduction
1 Previous
2 Next
3 Pause/Play
4 Mic
5 Volume+
6 Volume-
7 Power
8 Line In Jack
9 USB Port
LED Indicator
Operation/State LED Indicator Status
Power On Blue light blinking
Pairing Mode Alternating red and blue lights
Power Off Red light on for three seconds
Charging Indicator Red light on
Fully Charged Blue light on
Calling Blue light blinking
In Conversation Blue light blinking
www.smartomi.com support@smartomi.com 4
Adjustable Headphone
Adjustable HeadphoneThe headband is adjustable onboth sides for optimum comfort.
Rotary Function45°-90° rotation for easytransport and storage.
www.smartomi.com support@smartomi.com
Calling Operation
Answering/Ending a Call:
Rejecting a Call:
Music/Call Switch:
Press the power button to accept a call.
Press the power button again to end a call.
Method 1: Press and hold the power button for two seconds.
Method 2: Press the reject button on your phone.
Music is automatically paused when a call comes in.
When a call ends, music automatically resumes.
Redialing Last Number:Double press (two consecutive presses) the power button to call the last
number dialed.
6
Function Introduction
Tips: When paired with an iPhone, the headset’s battery level is displayed right
next to the headset icon near the top right corner of the screen.
The headset is automatically turned off if it is in pairing mode for more
than 5 minutes without a successful connection.
www.smartomi.com support@smartomi.com
Care and Maintenance
•Keep the headset away from heat and humidity.•Do not drop or bump the headset.•Do not use chemicals or detergents to clean the headset.
5
Pairing Instructions
Function Introduction
Step 1: Go into your phone’s list of Bluetooth devices.
Step 2: Keep your phone and the headset close to eachother (3 feet apart).
Step 3: With the headset off, press and hold the power button until theblue and red indicator lights on the left ear cup flash alternately.
Step 4: Locate and tap SMARTOMI Hoop from the list of Bluetooth devices that are available to pair with your phone. If prompted for a password, enter 0000. Pairing is complete when the red and blue lights stop blinking alternately, leaving only the blue light blinking.
Step 5: After successful pairing, the headset can now be used to listento music or make phone calls.
1. Please make sure the Bluetooth function of your devices in the status of
turn off before pairing. And if you paired the Hoop with your devices before,
please remove the pairing record on your devices first.
2. Keep your phone and the headset close to each other (3 feet apart).
3. With the headset off, press and hold the power button until the blue and
red indicator lights on the left ear cup flash alternately.
4. Turn on the Bluetooth on your device A, locate and tap SMARTOMI Hoop
on device A. Pairing is complete when the red and blue lights stop blinking
alternately, leaving only the blue light blinking.
5. Turn off the Bluetooth function on device A, then turn on the Bluetooth
function on device B, locate and tap SMARTOMI Hoop on device B. Pairing
is complete when the red and blue lights stop blinking alternately, leaving
only the blue light blinking.
6. Turn on the Bluetooth function on device A again, and tap SMARTOMI
Hoop on device A to complete the pairing with the device A, then multi-point
devices pairing will be done.
www.smartomi.com support@smartomi.com
Multi-Point Devices Pairing:
7
Function Introduction
www.smartomi.com support@smartomi.com 8
Product Specifications
Speaker Specifications
Speaker diameter: Ø40mm
Impedance: 32Ω
S. P. L: 115 ± 3dB S. P. L. at 1KHz
Rated power: 20mW
Aggregate capability: 40mW
Frequency Response: 20Hz-20,000Hz
Microphone Specifications
Microphone Unit: Ø4*1.5mm
Microphone directivity: full directivity
S. P. L: -42 ± 3dB
Impedance: ≤2.2KΩ
Frequency Response: 30Hz-16,000Hz
Operating voltage: 3.0V
www.smartomi.com support@smartomi.com 9
Specifications
Specifications
Dimension: 170*200*75mm
Bluetooth Version: BT4.1
Bluetooth IC: CSR8645 with aptX
Net Weight: 189g
Operating Voltage: 3.7V
Low Power Indication Voltage: 3.4V
Play Time: 16 Hours
Charging Voltage: DC 5V
Charging Connector: Micro USB Interface
Charging Time: 1 Hour
Charging Current: 500mA
Extra Audio Input Interface: 3.5mm Headphone Jack
Thanks you for choosing SMARTOMI. We provide 24/7 customer service becauseyour satisfaction is our top priority. If you have any questions, issues or problemsabout our products or services, please feel free to contact us atsupport@smartomi.com. We’re always here to help.