Post on 02-Jun-2018
8/10/2019 UIS011
1/1
Ultimet Group
DISCLAIMER
These data sheets are based on specifications, data and test results at time of
publication. No guarantee as to completeness, accuracy or results is either expressed
or implied. The suitability for an intended use is the responsibility of the user. As choice
of material, method of application and site conditions are beyond our control we accept
no liability for direct or consequential damages. Any material proved to be defective
within the published shelf life, from date of supply, will be replaced.
01634 232666Email: industrial@ultimetgroup.com
Website: www.ultimetgroup.com
ULTIMET INDUSTRIALPART OF THE ULTIMET GROUP
CALCIUM SILICATE PIPE & BLOCK INSULATION
DescriptionHI-THERM calcium silicate block and pipe high temperatureinsulation is manufactured using an industry preferred filterpress method which provides accurate dimensional toler-ances and superior compressive and flexural strength.These attributes facilitate installation and provide exception-
al resistance to mechanical abuse. HI-THERM calcium sili-cate insulation is asbestos free and meets or exceeds all ofthe requirements of ASTM C 533, Type I.
ApplicationsHI-THERM calcium silicate insulation is recommended foruse on equipment and piping operating at temperaturesfrom ambient to 250 Deg F (121 Deg C) indoors and pro-tected outdoors up to 1200 Deg F (649 Deg C). it is ideallysuited for industrial use in areas such as the petrochemicaland power generating industries where energy conservation,process control, personal protection and fire protection areprerequisites.
Forms availableHI-THERM calcium silicate block and pipe insulation are
availableProduct RangeCalcium Silicate Pipe CoverLength: 3 feet (915mm)Diameter: half-37 inches (22-942mm)
half-19 inches 2 pcs/section20-28 inches 4 pcs/section29-37 inches 6 pcs/section
Thickness:1-3 inches (25-76mm) in single layer in half inch (13mm)increments. Over 3 inches (76mm) are layed
Calcium Silicate BoardLength: 3 feet (915mm)Width: 6 inch/12inch (150/305mm)Thickness: 1-3 inches (25-75mm)
Other Type available Service Temperature: 1200 Deg F (650 Deg C) Service Temperature: 2012 Deg F (1100 Deg C) Density: 10-11 Ib/cu.ft. (170kg/m3) Density: 8-9Ib/cu.ft. (130-150kg/m3) Length: 2 feet (600 / 610mm) 3 feet (915mm) on request Board Width: 6 inch / 12 inch (150 / 300mm) Groove & Curved Board with 2 bevelled edges Other sizes available upon request
PHYSICAL PROPERTIES HI-THERM, nominal A.S.T.M.
Compressive Strength 177 psi. to Produce 5% Min. 100 psi.
(AS TM C 165) co mpressio n (1206 kPa) (688 kP a)
Dens ity ( dr y) Ave rage 14 .5 I bs . Per cu .f t. Max 15 .0
(ASTM C 302) (232 kg/m3) (240 kg/m3)
Flexural Strength 70 psi. Min. 50 psi.
(ASTM C 203) (483 kPa) (344 kPa)
Tumbl ing Fri ab il it y 10 % a ft er f ir st 1 0 min Max. 20 %
(AS TM C 421) 20% after second 10 min. Max . 40%
Linear Shrinkage Less than 2% after 24 Max . 2%
(ASTM C 356) Hour soaking period at
1200 deg F.
Surface Burning Flame Spread-0 Max. 0
Characteristics Smoke developed-0 Max. 0
(ASTM E 84)
Max. Service Temperature 1200 Deg F. Max. 1200 deg F
(ASTM C 411) (649 Deg C.) (649 Deg C)
SPECIFICATION COMPLIANCEASTM C 533, TYPE IASTM C 795Tested by TUTCO SCIENTIFIC CO., USA(Test Report Copies on request)
THERMAL CONDUCTIVITY ("K")*Mean K Mean KTemp Btu-in. Temp W/MDeg. F /h-ft2-Deg F Deg. C Deg. C200 .390 93 .0562300 .418 149 .0603400 .458 204 .0660500 .512 260 .0738
600 .579 316 .0835700 .659 371 .0950
ASTM C 533 Test Data
UIS011
mailto:industrial%40ultimetgroup.com?subject=http://www.ultimetgroup.com/http://www.ultimetgroup.com/mailto:industrial%40ultimetgroup.com?subject=