Post on 20-Jan-2021
i
ii
TWO AXIS DIRECTION FINDING ANTENNA SYSTEM USING
DIFFERENCE – SUM PATTERNS IN X-BAND
by
SARMAD AHMED SHAIKH
Submitted to the Graduate School of Engineering and Natural Sciences
in partial fulfillment of
the requirements for the degree of
Master of Science
Sabanci University, Turkey
January, 2015
ii
iii
TWO AXIS DIRECTION FINDING ANTENNA SYSTEM USING
DIFFERENCE – SUM PATTERNS IN X-BAND
Sarmad AHMED
EE, MS THESIS, 2015
Thesis Supervisor: Prof. Dr. Ibrahim Tekin
Keywords: Microstrip Patch Antenna, Antenna Array, Direction of Arrival
Systems and Rat Race Ring Coupler.
Abstract:
This thesis work proposes the direction finding antenna system in two axis (θ,∅) in x-band (8
to 12 GHz) using difference (∆) and sum (∑) patterns of received signal. Direction finding
system is constructed using microstrip patch antennas array and 1800 hybrid rat race ring
coupler which generates ∆ and ∑ of two received RF signals. Individually, both coupler
circuit and antenna elements are optimized in terms of feed location and size using ADS
electromagnetic simulation software. In this work, 10 GHz frequency of operation is chosen.
Initially, direction of arrival (DOA) is obtained in one axis (θ) using the patterns of ∆ and ∑
ports of antenna array of two elements. Using the equations of ∆ and ∑ of two input signals,
radiation patterns at different 𝜃 values have been observed in simulation and compared with
measured pattern values of constructed circuit. By taking the ratio of ∆ to ∑ patterns, DOA
has been estimated of designed circuit. Later, another DOA circuit in other direction (∅) is
constructed and DOA has been estimated. By taking the 3D patterns of each circuit in
anechoic chamber, both of these circuits are simulated and measured for performance; and
from -40 to +40 degrees DOA has been observed with rms error of less than 5 degree in both
axis with phi angle from 0 to 180 degrees. Another circuit which combines all these four
antennas into one system also has been simulated.
At 10 GHz operating frequency, experimental results using material RT Duroid 5880
(𝜀𝑟 = 2.2, 𝑡𝑖𝑐𝑘𝑛𝑒𝑠𝑠 = 1.575𝑚𝑚) show that satisfactory performance can be achieved with
proposed setup.
iv
FARK VE TOPLAM YAPISI KULLANARAK İKİ EKSENDE YÖN
BULUCU X-BAND ANTEN SİSTEMİ
Sarmad AHMED
EM, Yüksek Lisans Tezi, 2015
Tez Süpervizörü: Prof. Dr. Ibrahim Tekin
Anahtar Kelimeler: Mikroşerit Yama Anten, Anten Dizisi, Geliş Yönü
Sistemleri ve Rat-Race Halka Eşleyicisi.
Özet:
Bu tez, gelen sinyalin farkını (∆) ve toplamını (∑) kullanarak X bandında (8-12 GHz) iki
eksende (θ,∅) yön bulucu anten sistemi sunmaktadır. Yön bulucu sistem, mikroşerit yama
antenleri ve gelen RF sinyalin ∆ ve ∑‟ını alan rat-race halka eşleyicisinden oluşur. Bireysel
olarak, hem eşleyici devre hem de anten elemanları ADS elektromanyetik simülasyon
yazılımı kullanılarak besleme yeri ve boyut bakımından optimize edilmiştir. Bu projede,
çalışma frekansı 10 GHz olarak belirlenmiştir.
Başlangıç olarak, iki antenden oluşan anten dizisinin ∆ ve ∑ portlarını kullanarak tek eksende
(θ) sinyalin geliş yönü (SGY) bulunur. İki girdi sinyalinin ∆ ve ∑ denklemleri kullanılarak,
farklı 𝜃 değerlerindeki yayınım yapısı simülasyonda gözlemlenir ve üretilen devrenin
ölçümlerinden elde edilen yayınım yapılarıyla karşılaştırılır. ∆‟ın ∑‟a oranı hesaplanarak,
tasarlanan devreden SGY öngörülür. Yankısız odada 3 boyutlu sinyal yapılarına bakılarak,
her iki devre de simüle edildi ve ölçüldü; aynı zamanda -40°‟den +40°‟lik açıya kadar 5°‟den
daha az bir ortalama karekök (RMS) hatasıyla ve her iki eksende 0°‟den 180°‟ye kadar phi
açısıyla SGY gözlemlendi. Bütün bu dört anteni içeren başka bir devre de ayrıca simüle
edildi.
10 GHz çalışma frekansında, RT Duroid 5880 (𝜀𝑟 = 2.2, 𝑘𝑎𝑙ı𝑛𝑙ı𝑘 = 1.575𝑚𝑚) malzemesi
kullanılarak elde edilen deney sonuçları gösterdi ki önerilen kurulum ile tatmin edici
performans parametrelerine ulaşılabilir.
v
Acknowledgements
First of all I would like to acknowledge my thesis supervisor Dr. Ibrahim Tekin and
would like to thank and express my deepest gratitude for his valuable guidance,
support, continuous encouragement and keeping me motivated all the time. It is a
wonderful experience and honor for me to work with him for entire my masters
degree. Specially I would like to appreciate his instantly help, patience and
encouragement during the thesis work.
I am also thankful to my dissertation jury members, Dr. Orguz Gurbuz and Dr. Gullu
Kiziltas for spending their valuable time to judge my thesis.
I would like to acknowledge Higher Education Commission (HEC), Pakistan for their
great co-operation and by keeping trust to award me full funded scholarship to obtain
Masters degree at Sabanci University, Turkey.
I also cannot stay away to myself to acknowledge my lovely lab fellows PhD students,
Haq Nawaz and Mir Mehdi for their wonderful and appreciable assistance for my
asked questions and specially during the fabricated circuits measurements performed
in Anechoic chamber.
Last but not least, I would like to say bundles of thanks to my family and friends for
their endless morally support in every step during my academic life.
vi
Dedicated to my late father Gul Mohammad......
vii
©Sarmad AHMED 2015
All Rights Reserved
viii
TABLE OF CONTENTS
1. INTRODUCTION ....................................................................................................................... 1
2. BACKGROUND ......................................................................................................................... 4
2.1 DOA SYSTEM ....................................................................................................................... 4
2.2 ANTENNA BASICS AND ITS PARAMETERS ............................................................................ 6
2.2.1 DIRECTIVITY AND GAIN OF ANTENNA ....................................................................... 8
2.2.2 REFLECTION COEFFICIENT (ᥬ) AND RETURN LOSS (RL) ............................................. 9
2.2.3 3DB BEAMWIDTH ........................................................................................................ 9
2.2.4 BANDWIDTH ................................................................................................................. 9
2.3 MICROSTRIP ANTENNAS ..................................................................................................... 9
2.3.1 MICROSTRIP PATCH ANTENNAS ................................................................................ 10
2.3.2 DESIGN PROCEDURE .................................................................................................. 11
2.3.3 MICROSTRIP PATCH ANTENNA FORMULATIONS ....................................................... 13
2.3.4 ADS SIMULATION OF 10GHZ MICROSTRIP PATCH ANTENNA .................................. 15
2.3.5 MICROSTRIP ANTENNA ARRAYS ................................................................................ 19
3. RAT RACE COUPLER ............................................................................................................ 22
3.1 1800 HYBRID RING COUPLER DESIGN .............................................................................. 23
4. DOA FINDING SYSTEM DESIGN AND EXPERIMENTAL RESULTS ................................... 30
4.1 ∆ – ∑ PATTERN ANALYSIS THROUGH MATLAB CODING ..................................................... 30
4.2 ESTIMATING DOA IN THETA (Θ) AXIS ............................................................................... 31
4.3 ESTIMATING DOA IN PHI (∅) AXIS .................................................................................... 40
5. CONCLUSION .......................................................................................................................... 51
6. APPENDICES ........................................................................................................................... 53
6.1 APPENDIX A ....................................................................................................................... 53
6.2 APPENDIX B ........................................................................................................................ 56
6.3 APPENDIX C ........................................................................................................................ 57
7. REFERENCES .......................................................................................................................... 59
ix
LIST OF FIGURES
FIGURE 2-1: BLOCK DIAGRAM OF DOA SYSTEM ............................................................................... 5
FIGURE 2-2: TYPICAL PATTERN OF DIFFERENCE AND SUM PORTS ...................................................... 6
FIGURE 2-3: ANTENNA IMPEDANCE VERSUS FREQUENCY, SHOWING RESONANCE FREQUENCY ....... 8
FIGURE 2-4: BASIC MICROSTRIP PATCH ANTENNA DESIGN .............................................................. 11
FIGURE 2-5: DIFFERENT PATCH ANTENNA DESIGNS WITH MATCHING TECHNIQUES …………. ...... 12
FIGURE 2-6: BASIC GEOMETRY OF QWT FED MICROSTRIP PATCH ANTENNA .................................. 13
FIGURE 2-7: TL MODEL OF MICROSTRIP PATCH ANTENNA .............................................................. 14
FIGURE 2-8: LINECALC PARAMETERS FOR RT DUROID 5880 .......................................................... 17
FIGURE 2-9: LAYOUT DESIGN OF 10 GHZ PATCH ANTENNA ............................................................. 17
FIGURE 2-10: S11 OF DESIGNED 10GHZ PATCH ANTENNA ............................................................... 18
FIGURE 2-11: ANTENNA PARAMETERS OF DESIGNED 10 GHZ PATCH ANTENNA ............................. 18
FIGURE 2-12: 3D RADIATION PATTERN OF DESIGNED 10GHZ PATCH ANTENNA .............................. 19
FIGURE 2-13: 2D GAIN AND RADIATED POWER PLOTS OF DESIGNED 10GHZ PATCH ANTENNA ....... 19
FIGURE 2-14: 4-ELEMENT PATCH ARRAY ......................................................................................... 20
FIGURE 3-1: TYPICAL RAT RACE RING COUPLER DESIGN ................................................................. 22
FIGURE 3-2: SCHEMATIC DESIGN OF 1800HYBRID RAT RACE RING COUPLER .................................. 24
FIGURE 3-3: SCHEMATIC S11, S22, S33 AND S44 OF PORT1, PORT2, PORT3 AND PORT4 ................ 24
FIGURE 3-4: PORT ISOLATIONS ......................................................................................................... 25
FIGURE 3-5: 1800PHASE DIFFERENCE IN BETWEEN TWO INPUT SIGNALS AT PORTS 3 AND 4 .......... 25
FIGURE 3-6: TWO INPUT SIGNALS ARRIVING IN PHASE AT SUM PORT .............................................. 26
FIGURE 3-7: LAYOUT DESIGN OF RAT RACE COUPLER AT 10 GHZ CENTRAL FREQUENCY ............... 27
FIGURE 3-8: LAYOUT S11,S22,S33,S44 OF PORTS 1,2,3,4 RESPECTIVELY ......................................... 27
FIGURE 3-9: PORT ISOLATIONS ......................................................................................................... 28
FIGURE 3-10: 1800PHASE DIFFERENCE IN BETWEEN TWO INPUT SIGNALS AT PORTS 3 AND 4 ......... 28
FIGURE 3-11: TWO INPUT SIGNALS ARRIVING IN PHASE AT SUM PORT ............................................ 29
FIGURE 4-1: NUMERICALLY OBTAINED ∆ AND ∑ PATTERNS ............................................................ 30
FIGURE 4-2: ADS LAYOUT DESIGN OF ∆ - ∑ PATTERN, CIRCUIT 1 (THETA AXIS) ............................ 32
FIGURE 4-3: S-PARAMETERS OF ∆ AND ∑ PORTS, SIMULATED IN ADS LAYOUT .............................. 33
FIGURE 4-4: FAR FIELD PATTERN AT 0 DEGREE ................................................................................ 34
FIGURE 4-5: ANTENNA PARAMETERS .............................................................................................. 34
FIGURE 4-6: DIFFERENCE – SUM PATTERN CIRCUIT 1 FABRICATED (THETA AXIS) .......................... 35
FIGURE 4-7: TESTING THE CIRCUIT IN ANECHOIC CHAMBER WITH HORN ANTENNA ...................... 36
FIGURE 4-8: MEASURED S-PARAMETERS OF ∑ AND ∆ PORTS, RESPECTIVELY .................................. 36
FIGURE 4-9: MEASURED NORMALIZED ∆ AND ∑ PATTERNS OF CIRCUIT 1 ...................................... 37
FIGURE 4-10: MEASURED ANGLE OF ARRIVAL OF RECEIVED SIGNAL OF CIRCUIT1 (THETA AXIS) .. 37
x
FIGURE 4-11: PLOTS OF ESTIMATED AOA -400 TO 400
IN THETA AXIS AT DIFFERENT PHI VALUE . 38
FIGURE 4-12: RMS ERROR FOR MEASURED DOA IN THETA AXIS (-400 TO +400) .......................... 39
FIGURE 4-13: RMS ERROR AT DIFFERENT DOA RANGES IN THETA AXIS......................................... 39
FIGURE 4-14: ADS LAYOUT DESIGN OF ∆ - ∑ PATTERN, CIRCUIT 2 (HORIZONTAL) ........................ 41
FIGURE 4-15: S-PARAMETERS OF ∆ AND ∑ PORTS, SIMULATED IN ADS LAYOUT ............................ 41
FIGURE 4-16: FAR FIELD PATTERN ................................................................................................... 42
FIGURE 4-17: ANTENNA PARAMETERS ............................................................................................ 43
FIGURE 4-18: DIFFERENCE – SUM PATTERN CIRCUIT 2 FABRICATED (PHI AXIS) ............................. 43
FIGURE 4-19: MEASURED S-PARAMETERS OF ∑ AND ∆ PORTS, RESPECTIVELY OF CIRCUIT 2 ......... 44
FIGURE 4-20: MEASURED NORMALIZED ∆ AND ∑ PATTERNS (CIRCUIT 2) ...................................... 45
FIGURE 4-21: MEASURED ANGLE OF ARRIVAL OF RECEIVED SIGNAL OF CIRCUIT2 (PHI AXIS) ....... 45
FIGURE 4-22: PLOTS OF ESTIMATED AOA -400 TO 400 IN PHI AXIS AT DIFFERENT THETA VALUES 47
FIGURE 4-23: RMS ERROR FOR MEASURED DOA IN PHI AXIS (-400 TO +400) ................................ 48
FIGURE 4-24: RMS ERROR AT DIFFERENT DOA RANGES IN PHI AXIS .............................................. 48
FIGURE 4-25: ESTIMATED DOA IN BOTH AXIS (THETA AND PHI) AT FIXED PHI VALUE (0 DEG.) ..... 49
FIGURE 4-26: OVERALL SYSTEM DESIGN ......................................................................................... 50
1
1. Introduction
The objective of this thesis is to design a microstrip patch antenna array with rat race
coupler in x-band of frequency to estimate the direction of arrival (DOA) or the angle
of arrival (AOA) of received signal. Main motivation behind the antenna array and rat
race coupler system is to find the direction of received signal in two axis using the sum
(∑) and difference (∆) patterns at 10 GHz operating frequency. As part of the array
section across a microstrip patch antenna is designed as the receiving element of RF
signal. Further, rat race coupler is designed and optimized at the central frequency in
order to obtain accurate sum and difference of two received signals.
The direction of arrival estimation system having applications in radar, sonar, military,
acoustic, communications and medical imaging, is an omnipresent task in array signal
processing [1]. Recently developed a great number of radar and sensor systems require
high efficiency, functionality and compactness [2]. One of the efficient methods of
improving the quality of received signal is to find the DOA of the signal by targeting
the reception only on the expected direction and rejecting the interferer reception from
other directions [3]. Hence the main objective of DOA system is to define a function
which finds the AOA of received signal. Many publications have studied the DOA
system design and its characteristics which suggest different types of algorithms to
estimate the direction of received signal. The techniques used in literature in finding
the DOA are generally complex and their focus is mainly in one axis only.
The focus of this thesis is to find the DOA of received signal in x-band (10 GHz)
frequency in two axis (𝜃 𝑎𝑛𝑑 ∅) using the difference and sum patterns of most popular
1800 hybrid rat race ring coupler. System design includes two antenna arrays placed in
two directions (vertical and horizontal) each consists of two microstrip patch antennas
operating at 10 GHz frequency, rat race ring coupler providing the difference and sum
of two received RF signals; and feeding network. When two signals are received by
two antenna elements of an array, these two signals are applied to the two input ports
of 4 ports ring coupler which generates difference (∆1) and sum (∑1) on two output
ports. Using the difference and sum patterns of coupler, direction of arrival of received
signal is estimated in one axis (𝜃) using the AOA function which is explained in
details in section (4) of this thesis. For the sack of clear understanding, let‟s call this
part of design as circuit 1 (in vertical direction). Similarly, another same part of design
is constructed which is at 900of first circuit and let‟s call it as circuit 2 (in horizontal
direction) which provides difference (∆2) and sum (∑2) patterns of two received
signals. By applying DOA function on obtained patterns as done in circuit 1, DOA in
second axis (∅) has been obtained. All this work is first simulated and tested on
2
Advanced System Design (ADS) momentum software and then constructed on RT
Duroid 5880 material.
Each part of the system is designed and tested on ADS software separately and
optimized to the desired range of expected results. Initially microstrip patch antenna
was designed at 10 GHz central frequency and input impedance was matched using
quarter wave transformer method. This designed patch antenna was analyzed carefully
which in result provided better S-parameters, gain, directivity and radiation pattern. In
Matlab, by multiplying the radiation pattern (gain plot) of this single patch antenna
with the equations of sum and difference, radiation patterns of both ∑ and ∆ are
analyzed numerically. This part of the design is well explained in next section (4).
After getting good design of patch antenna, array of two antenna elements was
implemented using 0.6 𝜆 spacing in between two elements where 𝜆 =30 millimeter
(mm) is free space wavelength at 10 GHz frequency at the speed of light (v=3 x 108
meter/second). In order to get the ∑ and ∆ of two received signals from two antenna
elements of array, 1800 hybrid rat race ring coupler was designed separately at 10
GHz and optimized for the desired outputs. Complete studies regarding rat race
coupler is discussed in section (3). All parts of the system are very carefully designed
and optimized in ADS momentum software to get the proper results.
Having simple structure of array of two elements of patch antennas and ring coupler,
system design is much straight forward and able to provide the direction of arrival of
received signal using difference and sum patterns. However, it has been investigated
that transmission lines of 50 Ω at 10 GHz produces mutual coupling if passing near the
patch antenna or coupler which consequently disturbs the patterns of sum and
difference ports. Therefore, good care was given in transmission lines design which
resulted in better ∑ and ∆ patterns.
The thesis is organized as follows:
Chapter 1: This section of thesis provides the introduction to the thesis work,
objective, approach and scope of the work.
Chapter 2: Gives essential background about DOA system and covers the
literature review on microstrip patch antennas and array design. For this thesis work,
10 GHz patch antenna is designed and investigated in this section.
Chapter 3: Analyzes the 4 ports 1800 hybrid rat race ring coupler. It is well
investigated through ADS layout and schematic simulations.
Chapter 4: Discusses the complete design both in hardware and software
format of direction finding system. Also gives the results obtained from simulations
and measurements of the system design.
3
Chapter 5: Concludes the work of this thesis done.
Chapter 6: Gives appendices about supplementary and necessary formulations
and Matlab codes.
4
2. Background
2.1 DOA System
Efficiently estimating the direction of received signal has remained challenging task in
radar, military and communication systems working in x-band of frequency. It is
necessary to focus the reception in estimated direction and rejecting in all other
directions which in result increases the quality of received signals. There exist many
algorithms in finding the DOA such as sensor array, Bartlett method, Capon method,
MUSIC algorithm, etc [1][3]. But these algorithms are generally complex and
depending on number of antennas employed and their parameters such as spacing
between them, gain and directivity; number of users, geographical position, and
number of sample signals taken in estimating process [4].
It is known that there exist one to one relationship between direction of a signal and
the associated received steering vector [5]. It is therefore possible to estimate the
direction of received signal by inverting this relationship. So in this thesis work a
novel antenna system using difference (∆) and sum (∑) patterns of received 10 GHz
signal is proposed. This proposed DOA finding system consists of microstrip patch
antenna array, rat race ring coupler and feeding network. Block diagram of simple
DOA system is shown in figure 2-1.
Received signals of antenna array elements are fed to two input ports of 4-ports 1800
hybrid rat race ring coupler which generates the difference (∆) and sum (∑) of two
received signals at two output ports. Coupler produces the ∆ and ∑ of the fed signals
according to the following equations, respectively:
∆ = 1 - e−jkdsin θ (2-1)
∑ = 1 + e−jkdsin θ (2-2)
Using this pattern of ∆ and ∑, angle of arrival is derived by taking the ratio ∆ to ∑ .
After performing some mathematical iteration, AOA can be estimated as given in
following equation (2-3) [2].
θ = sin−1 𝜆
𝜋𝑑tan−1 ∆
∑ (2-3)
where λ is free space wavelength, d is spacing between two antenna elements, ∆ and ∑ are
the subtracted and summed amplitudes of RF signals received by antenna array of two
elements.
5
Typical patterns of difference and sum ports of coupler as given in [2] are shown in
figure (2-2) in order to take in account as pre-requirement of coupler‟s output.
∅ θ
X
Y
Figure 2-1: Block diagram of DOA System
z
6
Figure 2-2: Typical pattern of difference and sum ports [6].
2.2 Antenna Basics and its Parameters
Antenna is a device also often called radiant, designed to transmit or receive
electromagnetic energy by matching these sources of energy and the space. Note that
the same antenna can be used to transmit or receive the radio signals.
As mentioned in [7], in addition to transmitting and receiving the electromagnetic
energy, an antenna in an advanced wireless system is usually required to optimize or
accentuate the radiation energy in some particular directions and block it in other
directions. Therefore, antenna can also be used for any required direction as well.
Antenna in its physical form can be a piece of conducting wire, a copper patch, an
aperture, an assembly of many elements (array), a reflector, a lens, and so forth (note
that here in this work only patch antenna will be discussed in details). So
an antenna being a device used for converting electromagnetic radiation in space into
electrical currents in conductors or vice-versa, depending on whether it is being used
for receiving or for transmitting, respectively, is usually easier to calculate the
properties of transmitting antennas. Fortunately, most properties of a transmitting
antenna remain unchanged when the antenna is used in receiving mode. Often the
same analysis of a transmitting antenna is carried to understand a receiving antenna
used in radio astronomy.
7
The information which is supposed to be sent is varied, for example through some
kind of digital/analogue modulation scheme and treatment, and still conveyed or
guided by a cable to the antenna. The antenna then starts its work and radiates this
information through a medium (usually air) until it reaches the other receiving
antenna, which in this case will make receiving the signal, making it still the way the
cable to the device that will make such demodulation (and other treatments),
recovering the original information. There also occurs some path losses and
attenuation of signals which degrades the received signal quality.
Antenna is usually made of metallic material (aluminum / brass) and metal itself is
formed by atoms. When all atoms are brought together to make metal then there is a
set of free electrons which start to move when a voltage is applied. Motion of these
electrons on antenna creates electromagnetic radiation in the form of radio waves.
Electromagnetic waves transmitted from transmitting antenna travel in free space
medium and reach at receiving antenna which again convert the electromagnetic
waves into electrons and make them to vibrate same as in transmitter which in turn
results in generating the current corresponding to the transmitted information.
While talking about electromagnetic waves, another important concept is the
polarization which is very important to be considered while designing the antennas,
i.e., what is the plane of the electrical component of the field in which the wave
propagates. In [5] and [8], it is well explained that electromagnetic waves are
composed of two planes, vertical and horizontal. These planes represent the electric
and magnetic fields and these components are always orthogonal, vectors off by 90
degrees. They vary in phase or zero degrees of electrical phase shift. So in short,
depending on how the signal coupling is done - the antenna is oriented - we have a
definition of polarization. The concept of polarization is very important in antennas,
mainly because when a signal is transmitted in one polarization must be received in the
same polarization, otherwise we will have an attenuation (loss), known as cross-
polarization.
Apart from polarization, there is also an important concept in antenna phenomenon
called „resonance or operating frequency‟. Resonance is the phenomenon that occurs
in a particular frequency where we have a maximum possible transfer of energy in that
particular defined frequency. In the case of antennas, for there to be resonance, its size
(physical length) must be a multiple of the wavelength of the transmitted/received
signal. In this case, we will have a main frequency where the antenna delivers the
maximum amount of energy possible - resonant. The larger the size (length) of
elements of antenna, lower the resonant frequency and vice versa [8]. In more
technically terms it can be described that resonance is where the inductance and
capacitance reactance cancel each other and we have pure resistive impedance as
shown in following figure 2-3.
8
Figure 2-3: Antenna Impedance versus Frequency, showing the resonance frequency
Following are the most important parameters to be analyzed when designing any type
of antenna.
2.2.1 Directivity and Gain of Antenna
One of the most important parameters of antenna to measure is that how much it
concentrates the energy in a particular direction in preference to radiation in other
directions. This characteristic of antenna is called directivity and is equal to its power
gain if it is 100% efficient and mathematically is given by:
𝐷 =4𝜋
𝛺𝐴 (𝟐 − 𝟒)
Directivity: can also be defined as the ratio of radiation intensity in a certain direction
to the average radiation intensity, as given by equation (2) [1].
𝐷 𝜃,𝜙 =𝑈 𝜃,𝜙
𝑈𝑎𝑣𝑒 (𝟐 − 𝟓)
Gain: When an antenna is used in a system for example in a transmitting antenna, we
are actually interested in how efficiently the antenna transfers the available power at
its input terminals to its radiated power, together with its directivity properties.
Therefore, gain is used to quantify this and is defined as 4π times the ratio of radiation
intensity in a given direction to the net power accepted by antenna from the connected
transmitter, as given in equation (2.6) [2].
𝐺 𝜃,∅ =4𝜋𝑈 𝜃,∅
𝑃𝑖𝑛 (𝟐 − 𝟔)
9
2.2.2 Reflection Coefficient (ᥬ) and Return Loss (RL):
Reflection coefficient is defined to give ratio between reflected wave and incident
wave. Transmission lines have a resistance related with it which is called
characteristics impedance, denoted with 𝑍0. When transmission line is terminated with
an arbitrary load which has not same impedance as of transmission line then wave is
reflected back and power is not transmitted properly. Reflected wave is given by
following relation:
Γ = 𝑍𝑙 − 𝑍0
𝑍𝑙 + 𝑍0 (𝟐 − 𝟕)
Return loss is the parameter that shows the amount of power that is reflected due to the
impedance mismatch between the source and the load and is given by:
RL = -20log | Γ | (dB) (𝟐 − 𝟖)
2.2.3 3dB Beamwidth:
In addition to directivity, the radiation patterns of the antenna are also characterized by
their beamwidths and sidelobe levels. Some numerical aspects of the antenna pattern
properties can be defined after antenna pattern is plotted. Half-power beamwidth or
3dB beamwidth is the measure of the angular width of the -3dB points on the antenna
pattern relative to maximum level.
Direction where the maximum radiations are obtained is called the main beam/lobe
while smaller beams which can never be completely eliminated are away from the
main beam and are called side lobes and usually occur in undesired direction. Another
commonly quoted beamwidth is the null to null beamwidth. This is the angular
separation from which the magnitude of the radiation pattern decreases to zero
(negative infinity dB) away from the main beam [9].
2.2.4: Bandwidth:
Defines the range of frequency over which antenna meets certain performance criteria.
It is generally defined through the return loss of the antenna for the frequency band in
which return loss is less than -10dB.
2.3 Microstrip Antennas
Microstrip antennas or Printed antennas are constructed using printed circuit
fabrication techniques such that a portion of the metallization layer is used to radiate
the electromagnetic energy in space. Microstrip patch elements and arrays of patches
are the most types of printed antenna and were conceived in 1950s [10]. This type of
10
antenna got much attention in 1970s and in turn it showed remarkable results with
many useful design configurations. Patch antennas are much popular among antenna
engineers because of their low profile, for the ease with which these antennas can be
configured to specialized geometries and also due to one of the promising advantage
of their low cost when produced in large quantities [11]. This section explains the
basic operating principles of microstrip patch antennas, design procedure and most
useful formulas which help to calculate the design parameters of the antenna. Details
and derivations of the formulas are given in [5] and [7].
2.3.1 Microstrip Patch Antennas
Microstrip patch antennas which are also called patch antennas are becoming
increasingly useful nowadays because they can be printed directly onto a circuit
board like any electronic circuit. Patch antennas are getting much popularity and
becoming very widespread within the mobile phone market because Patch antennas
are:
low profile
comfortable to planar and non-planar surfaces
simple and inexpensive to manufacture
compatible with MMIC circuit designs
versatile in frequency, polarization, radiation pattern and impedance
Having such great properties, patch antennas have low efficiency, low power, high Q,
narrow bandwidth and spurious radiation (surface waves).
As mentioned in [12], consider the microstrip patch antenna as shown in figure 2-4,
fed by a microstrip transmission line. The patch antenna, microstrip transmission line
and ground plane are made of high conductivity metal often made of copper. The
patch is made of length (L), width (W), and sitting on top of a substrate (some
dielectric circuit board) of thickness h with the substrate permittivity 𝜀𝑟 . The thickness
of the ground plane or of the microstrip is not critically important. Typically the
height h is much smaller than the wavelength of operation but not much smaller than
0.05 of a wavelength. Thick substrates with low 𝜀𝑟 are desirable for antenna
performance, better efficiency, larger bandwidth, larger element size while thin
substrates with high 𝜀𝑟 are desirable for microwave circuitry. Radiation mechanism is
through the fringing fields at the ends of the patch which can be treated as radiating
slots. As w/h >> 1 and 𝜀𝑟 >> 1, the electric lines concentrate mostly in the substrate.
Note that some of the waves travel in the substrate and some waves travel in the air, so
we have effective dielectric constant 𝜀𝑟 ,𝑒𝑓𝑓 given by equation (2-9).
11
εeff =εr +1
2+
εr−1
2[1 + 12
h
w]−1/2 (2-9)
According to reference [5], it is the fringing fields that are responsible for the
radiation. Note that the fringing fields near the surface of the patch antenna are both in
the +y direction. Hence, the fringing E-fields on the edge of the microstrip antenna add
up in phase and produce the radiation of the microstrip antenna. The current adds up in
phase on the patch antenna as well; however, an equal current but with opposite
direction is on the ground plane, which cancels the radiation. This also explains why
the microstrip antenna radiates but the microstrip transmission line does not. The
microstrip antenna's radiation arises from the fringing fields, which are due to the
advantageous voltage distribution; hence the radiation arises due to the voltage and not
the current. The patch antenna is therefore a "voltage radiator", as opposed to the wire
antennas, which radiate because the currents add up in phase and are therefore "current
radiators".
Figure 2-4: Basic microstrip patch antenna design
2.3.2 Design Procedure
The patch antenna belongs to the class of resonant antennas and its resonant behavior
is responsible for the actual challenge in this type of antenna design specially
obtaining the adequate bandwidth. Conventional patch designs yield bandwidths as
low as a few percent [13]. The resonant nature of microstrip antennas also means that
at frequencies below UHF they become excessively large in size. Therefore, these
antennas are typically used at frequencies range from 1 to 100 GHz. Further it is
12
discussed in [14] about tradeoff in microstrip antennas that is to design a patch with
loosely bound fields extending into space while keeping the fields tightly bound to the
feeding circuitry. Therefore, it is necessary to be accomplished with high radiation
efficiency and with the desired polarization, bandwidth and impedance.
Many designs exist for microstrip patch antennas with different styles of matching the
patch with transmission line, as Probe Feed, Microstrip Edge Feed with Quarter- wave
Transformer, Microstrip Edge Feed Inset, Probe Feed with a gap, Microstrip Edge
Feed with gap and Two-layer Feed; these all designs taken from [5], are shown in
figure 2-5. Figure 2-6 shows the most commonly used microstrip antenna, usually
called as rectangular or square patch being fed from a microstrip transmission line
and matched through quarter wave transformer (QWT) line section. Formulas are
available in literature to estimate the resonant length and width of patch and QWT line
but empirical adjustments are often necessary in practice. In this thesis, QWT fed
microstrip patch antenna is designed and used for antenna part of the DOA system at
desired frequency of operation.
Figure 2-5: Different patch antenna designs with matching techniques [5].
13
Figure 2-6: Basic geometry of QWT fed microstrip patch antenna
2.3.3 Microstrip Patch Antenna Formulations
There exist many modeling techniques of microstrip antenna. Three widely used
techniques are transmission-line, cavity and full-wave models. Transmission-line (TL)
having simplest model is easy to implement but with low efficiency. Cavity model
having better accuracy but increased complexity is empirical model like TL model that
utilizes assumptions to simplify the computations. While the full-wave model
computationally expensive provides an exact analysis of Maxwell‟s equations and
potentially provides the best precision because it considers boundary conditions on the
dielectric-air periphery.
In TL model the radiation from microstrip patch antennas can be calculated from the
equivalent magnetic current distributions around the edges of radiating patch.
Magnetic current values can be obtained from edge voltage distributions. Thus for a
given excitation and for a specified mode of the resonance of the patch, problem
reduces to that of finding the edge voltage distribution. The microstrip patch antenna
is modeled as two radiating slots separated by distance 𝐿𝑒𝑓𝑓 . By looking at figure 2-7,
physical meaning of this 𝐿𝑒𝑓𝑓 can be understood which is essentially the length of
patch denoted by L, plus an additional distance, 2∆𝐿, to account for the fact that
electric field of an open microstrip line does not end suddenly while the patch looks
larger than its physical dimensions due to fringing fields. While it can either introduce
a capacitance or equivalent length extension which is compensated in [7] by following
formula.
∆L = 0.412h 𝜀𝑟𝑒𝑓𝑓 + 0.3
𝑊
+ 0.264
𝜀𝑟𝑒𝑓𝑓 − 0.258 𝑊
+ 0.8
(2-10)
14
Figure 2-7: TL model of microstrip patch antenna
Here 𝜀𝑟𝑒𝑓𝑓 is the effective dielectric constant of microstrip TL which is given in
equation (2-9) and its value is slightly less than 𝜀𝑟 because the fringing fields around
the periphery of the patch are not confined in the dielectric substrate but also spread in
the air.
Moreover, length of the patch must be slightly less than 𝜆𝑔/2 in order to operate in
𝑇𝑀10 fundamental mode where 𝜆𝑔 is wavelength in dielectric medium and is given by
𝜆0/ 𝜀𝑟𝑒𝑓𝑓 where 𝜆0 is free space wavelength. More importantly, width (W) of the
patch plays a significant role in the microstrip antennas which requires a deep
attention. Small values of width result in low antenna efficiencies while large values
lead to the higher order modes. In this case for efficient radiation to obtain, width W is
given in [15] as follow:
W = 𝐶
2 𝑋 𝑓0 𝑋 (𝜀𝑟+1 )
2
(2-11)
For input impedance of resonate edge-fed patch, an expression is given in [7] as:
𝑍𝐴 = 90 𝜀𝑟
2
𝜀𝑟−1 (
𝐿
𝑊)2 Ω half-wave patch (2-12)
To find out the characteristic impedance of the matching section QWT as shown in
previous figure (2-6), we have
𝑍0′ = 𝑍0 𝑋 𝑍𝐴 (2-13)
Length of QWT section is 𝑙𝑞𝑤 = 𝜆/4 m.
The radiation pattern of the rectangular microstrip patch antenna for the 𝑇𝑀10 mode
could be calculated by combining the radiation pattern of the two slots of length ∆𝐿
and width W on the infinite ground plane, which are spaced at a distance L + ∆𝐿.
Simple expressions exist as given in [7] which approximate the radiation patterns of
the rectangular microstrip patch antenna and are given below.
15
𝐸𝜃 = 𝐸0 𝑐𝑜𝑠𝜙 𝑓 𝜃,𝜙 (2-14)
𝐸𝜙 = −𝐸0(𝑐𝑜𝑠𝜃)(𝑠𝑖𝑛𝜙)𝑓(𝜃,𝜙) (2-15)
𝑓 𝜃,𝜙 = sin
𝑘𝑊 sin (𝜃)sin (𝜙 )
2
𝑘𝑊 sin 𝜃 sin (𝜙 )
2
cos 𝑘𝐿𝑠𝑖𝑛 (𝜃)cos (𝜙)
2 (2-16)
where first part of the equation (2-16) is the pattern factor for a uniform line source
with length w and second part is corresponding to the array factor for two equally
excited elements having space L. To write the principle plane patterns, further
simplifications can be made, as given in [7].
𝐹𝐸𝜃 = cos 𝛽𝐿𝑠𝑖𝑛(𝜃)/2 (2-17)
𝐹𝐻𝜃 = cos(θ)sin
𝛽𝜔 sin (𝜃)
2
𝛽𝜔 sin (𝜃)
2
(2-18)
where θ is measured angle from the broadside.
2.3.4 ADS simulation of 10GHz microstrip patch antenna
After studying theoretical concepts, its good idea to design a patch antenna in any
antenna software, in order to verify the studied formulas of microstrip patch antenna.
Various types of softwares exist for antenna designing, such as High Frequency
Structure Simulator (HFSS), Advanced Design System (ADS), Numerical
Electromagnetic Code (NEC), Computer Simulation Technology (CST), etc. In this
thesis ADS software is used for simulation purpose. ADS momentum software is a
full-wave electromagnetic simulator based on the method of moments (MOM) and is
used to simulate the structure of the antenna. Antenna of interest is designed in the
layout part of the ADS of desired dimensions. Layout is composed of two layers, one
is patch layer and other is ground layer. Using internal port, patch feeding is obtained
and ground reference port to the internal port is defined at the ground layer.
Here, a patch antenna design at resonate frequency of 10GHz is given which will be
used further in desired DOA system. Before designing any required frequency
antenna, it is mandatory to select a dielectric substrate (𝜀𝑟 ) on which patch will be
drawn because all calculations depend on the properties of substrate, such as its
permittivity 𝜀𝑟value, tangent loss, thickness „h‟, conducting layer thickness „t‟ (as
copper), air value, etc. In this work, RT Duroid 5880 substrate is used throughout the
16
design and copper is used as conducting layer over the substrate. Substrate properties
are given in table 1.
Table 1: RT Duroid 5088 substrate properties
Substrate permittivity εr 2.2
Substrate Thickness h 1.575 mm
Substrate Tangent Loss 0.0004
Copper Conductivity 5.8 𝑒7 s/m
Copper Thickness t 17 𝜇𝑚
Having substrate values and desired frequency of operation (𝑓0), other required
parameters such as patch length L, width W, input impedance𝑍𝐴, QWT length 𝑙𝑞𝑤 and
width 𝑤𝑞𝑤 can be calculated using above mentioned formulas. Approximate values
can also be obtained using online antenna calculators as given in [16]. For parameters
εr = 2.2 , h=1.575 mm and 𝑓0 = 10𝐺𝐻𝑧, other parameters are calculated and given
below.
Free space wavelength (ℷ) = 𝑐
𝑓0=30mm; c= speed of light in space = 3 X 108 m/sec
Patch length = L = 9.0732 mm
Patch Width = W = 11.8585 mm
Patch input impedance = ZA= 212.50Ω using equation (2-12)
Characteristic impedance of QWT = Z0′ = 103.07Ω using equation (2-13)
QWT section length = lqw = 4.5886 mm
QWT section width = wqw = 1.4 mm
Width of 50Ω = w50= 5.0687 mm
Length of 50Ω = l50= 5.3583 mm
Note that w50 , l50 , lqw , wqw are calculated by using LineCalc facility of ADS
schematic feature and are optimized later in layout for desired results. Required
parameters of LineCalc window are given in figure (2-8) for substrate RT Duroid
5880.
17
Figure 2-8: LineCalc parameters for RT Duroid 5880
After calculating all required parameters, 10 GHz microstrip patch antenna is designed
in layout of ADS momentum software. Its design is given in following figure (2-9).
Note that, it is required to define the substrate parameters in the layout. After carefully
designing the patch antenna, it was simulated and S-parameters, antenna parameters,
3D radiation pattern and 2D gain & radiated power plots were analyzed and are given
in figures (2-10, 2-11,2-12 and 2-13), respectively. Return loss of -29.95dB is
observed at desired frequency of operation 10GHz. While efficiency of antenna
obtained as 85.26% with 6.730 dB gain and 7.399 dB directivity.
Figure 2-9: Layout design of 10 GHz patch antenna
18
Figure 2-10: S11 of designed 10GHz patch antenna
Figure 2-11: Antenna parameters of designed 10GHz patch antenna
19
Figure 2-12: 3D radiation pattern of designed 10GHz patch antenna
Figure 2-13: 2D gain and radiated power plots of designed 10GHz patch antenna
2.3.5 Microstrip Antenna Array
By increasing the transmit power, the coverage and operation range of a passive
system can be increased; however it is not applicable due to regulations on
transmitting power. In this case, keeping the same transmit power, operation range of
the communication channel can be raised by thanks of antenna array configuration. An
antenna array often called „phased array‟ consists of set of two or more than two
antenna elements. Purpose is that the signals from the antennas are combined or
20
processed in order to achieve improved performance over single antenna performance
[17]. Antenna array can be used to increase the gain of overall system, to provide
diversity reception, to focus the reception of signals from any particular direction as
DOA system and cancel out interference from a particular set of directions, to estimate
the direction of arrival of received signals; and to maximize the Signal to Interference
plus Noise ratio (SINR) [18].
As mentioned in [7], due to the advantage offered by the arrays of the microstrip
antennas, feed network as well as the radiating elements can be printed on the same
single layer on printed circuit board (PCB) of different types of material substrates.
Full integration (antenna elements, feeding circuitry and the chips) is possible with
technology. Microstrip antennas are used in many possible array configurations in
order to increase the gain. Patch arrays are popular for fixed-beam applications
(radiating network and the feed network on the same substrate) for low cost
lithographic PCB techniques. Inter element spacing is less than one wavelength to
avoid grating lobes and greater than half wavelength to provide room for feed lines (to
achieve higher gain for a given number of elements and to reduce mutual coupling).
Mutual coupling effects are not significant for patches that are spaced 0.57𝜆. Array can
be linear, planar or conformal; the feed can be parallel, series or hybrid. As an example
of 4 elements array, figure 2-14 is shown. The overall antenna pattern of a microstrip
patch array is formed with the contribution of each element. Antenna pattern can be
obtained by multiplying the single element pattern with a parameter called Array
Factor (AF). With angle differences, AF varies and shapes the single element pattern
to form the overall pattern of array. AF depends on the distances between patch
elements, total number of patch elements, the phase and amplitude differences of the
currents between adjacent patch elements and the frequency of the field. As stated in
[19] and [20], cross-polarization generated by higher order modes of a patch antenna
can be cancelled by proper use of the symmetry, elements placed symmetrically with
given element spacing in x and y coordination system.
Figure 2-14: 4-element patch array [7].
21
If we have M elements in x-axis with element spacing 𝑑𝑥 and N elements in y-axis
with element spacing 𝑑𝑦 , phase shift of 𝛽𝑥 between the elements in x-axis and 𝛽𝑦
between elements in y-axis; and element excitation as 𝐼𝑚 in the x-axis and 𝐼𝑛 in the y-
axis, then array factor of the planar antenna array can be calculated as in equation (2-
19) [20].
AF = ∑ 𝐼𝑚1𝑒𝑗 𝑚−1 (𝑘𝑑𝑥𝑠𝑖𝑛𝜃𝑐𝑜𝑠𝜙 + 𝛽𝑥 )𝑋 ∑ 𝑒𝑗 𝑛−1 (𝑘𝑑𝑦 𝑠𝑖𝑛𝜃𝑠𝑖𝑛𝜙 + 𝛽𝑦 )𝑁
𝑛=1𝑀𝑚=1 (2-19)
In this thesis work, in order to take the sum and difference of two signals, an array of
two elements is designed with element spacing of 0.6λ. This is more described in
details in section (4).
22
3. Rat Race Coupler
Rat race coupler or hybrid ring coupler having four ports is a type of coupler mainly
used in RF/microwave systems. It provides a great advantage of being easy to realize
in planar technologies such as microstrip and striplines although waveguide rat race
couplers also exist in practical. Power dividers and couplers are fundamental and
important passive circuits in RF/microwave front end. They can be incorporated with
balanced mixers and balanced amplifiers for equal or unequal power division [21].
Typical design of rat race ring coupler is shown in figure 3-1 which consists of two
input ports, named as port 1 and port 2 and two output ports, named as port 3 (sum)
and port 4 (difference). Therefore, this type of coupler is used to provide the sum and
difference of two in phase input fed signals. Each port of top half ring is spaced from
each other by 𝜆/4 distance while bottom ring is 3λ/4 in length. The ring has a
characteristic impedance of factor 2 compared to port impedance, for example, for
50 Ω, it is 2*50=70.7 Ω. Its circumference is 1.5λ or 6 times λ/4. So radius of ring
can be obtained from S=2πr where S is circumference (6*λ/4) and r is radius. For an
ideal 3dB rat race coupler, full s-parameter (scattering) matrix is given as in this
matrix
(2-21)
Figure 3-1: Typical rat race ring coupler design
23
3.1 𝟏𝟖𝟎𝟎 Hybrid Rat Race Ring Coupler
As mentioned earlier, 180° hybrid ring couplers are four-port devices used to either
equally split an input signal or to sum two combined signals. An additional benefit of
the hybrid ring is to alternately provide equally-split but 180 degree phase-shifted
output signals. This configuration creates a lossless device with low VSWR, excellent
phase & amplitude balance, high output isolation and match output impedances.
The parameters, substrate thickness h and dielectric constant 𝜀𝑟 are noticeable in
design because they relate to the characteristic impedance Zo, and should be calculated
carefully [22]. In this work h and 𝜀𝑟 , are chosen as 1.575 mm and 2.2 respectively. The
ring of coupler consists of six sections, the length of each section equals to L, (where
L=λ/4) and by using the following expression we can calculate the radius r, of the ring
[22].
r = 360 𝐿
2𝜋𝐶 (2-21)
Where C, is the angle in degree [23][24], this mean C, equal 600 for each section.
For this thesis work, 1800 hybrid ring coupler has been designed in order to obtain the
difference and sum patterns of the received signals. For this purpose first using ADS
schematic tool, a 1800 hybrid rat race ring coupler has been designed for desired
frequency of 10 GHz. Its schematic design with all calculated parameters is given in
figure 3-2. Schematic simulation results showed better S-parameters for all 4 ports of
coupler. In order to understand in easy way, let‟s assign the names to each port. Port 1
is the difference port, port 2 is the sum port, and Port 3 and Port 4 are the input feeding
ports. Return loss of each port (S11, S22, S33, S44) is given in figure 3-3 which shows
nice matching of each port with return loss of -45.94 dB. Port isolation between each
port is shown in figure 3-4. Figure 3-5 shows the phase difference of 1800 in order to
obtain the difference of two received signals. Figure 3-6 shows two input signals (port
3 and 4) arriving in phase at sum port (port 2).
24
Figure 3-2: Schematic design of 𝟏𝟖𝟎𝟎 hybrid rat race ring coupler
Figure 3-3: Schematic S11, S22, S33 and S44 of port1, port2, port3 and port4, respectively.
25
Figure 3-4: Port isolations
Figure 3-5: Phase difference of 𝟏𝟖𝟎𝟎 in between two input signals at ports 3 and 4
26
Figure 3-6: Two input signals arriving in phase at sum port
Later schematic design has been imported in layout tool of ADS and its design is given
in figure 3-7. After tuning/optimizing the layout design, simulation was run and S-
parameters are observed. This time S-parameters are slightly changed than schematic
because in layout simulations, ADS performs in chunks by making mesh around the
design. Return loss of each port is given in figure 3-8. Port isolation between each port
is shown in figure 3-9. Figure 3-10 shows the phase difference of 1800 in order to
obtain the difference of two received signals. Figure 3-11 shows Two input signals
(port 3 and 4) arriving in phase at sum port (port 2).
27
Figure 3-7: Layout design of rat race coupler at 10 GHz central frequency
Figure 3-8: Layout S11, S22, S33 and S44 of port1, port2, port3 and port4, respectively
28
Figure 3-9: Port isolations
Figure 3-10: Phase difference of 𝟏𝟖𝟎𝟎 in between two input signals at ports 3 and 4
29
Figure 3-11: Two input signals arriving in phase at sum port
30
4. DOA Finding System Design and Experimental Results
As discussed earlier, the objective of this thesis is to design a microstrip patch antenna
array with rat race coupler in x-band of frequency to estimate the direction of arrival
(DOA) or the angle of arrival (AOA) of received signals using the difference and sum
patterns of the coupler. After studying and successfully implementing patch antenna
and rat race coupler individually, its now time to integrate all these parts according to
mentioned design to analyze the difference and sum patterns in order to find out the
AOA in both axis separately. This analysis is discussed step by step in following
sections through Matlab coding, ADS simulations and practically fabrications of
desired circuits.
4.1 ∆ – ∑ Pattern Analysis through Matlab coding
Difference and sum pattern equations are given in equations (2-1 and 2-2) from which
it is possible to obtain the AOA by using equation (2-3). In order to analyze the ∆ and
∑ pattern numerically through Matlab, it is required to have the radiation pattern of
antenna element. For this purpose, radiation pattern of single patch antenna already
simulated in ADS can be used in order to plot the difference and sum patterns. By
multiplying the 2D gain pattern values of single patch antenna with equations (2-1 and
2-2), difference and sum plots are obtained through Matlab coding. Note that, this
Matlab coding is given in appendix A. After running the code, obtained normalized
difference and sum pattern v.s angle θ (in degrees) plot is given in figure 4-1.
Figure 4-1: Numerically obtained ∆ and ∑ patterns
31
4.2 Estimating DOA in θ axis
Estimating the direction of received signal specially in x-band of frequency is a
challenging task for radar, military and communication system applications. As
mentioned earlier that it is necessary to focus the reception in estimated direction and
rejecting in all other directions, which in result increases the quality of received
signals. For this purpose, there exist many algorithms in finding the DOA but these
algorithms are generally complex [4]. Due to one to one relationship between direction
of a signal and the associated received steering vector [5], it is therefore possible to
estimate the direction of received signal by inverting this relationship. In this thesis
work a novel antenna array system using difference (∆) and sum (∑) patterns of
received 10 GHz signal is proposed. This proposed DOA finding system consists of
microstrip patch antenna array, rat race ring coupler and feeding network.
Here, in order to take the two sample signals, array of two patch antennas has been
implemented. Spacing between two elements is chosen as 0.6λ (18mm) because more
than one λ spacing create grating lobes while less than 0.5λ produce mutual coupling
between two elements patterns which in result decrease signal to interference/noise
ratio of the received signal. After receiving the signal from each antenna element,
signals are fed as two input signals to the 4 ports 1800 hybrid rat race ring coupler.
Coupler by performing its operation according to equations (2-1 and 2-2), generates
difference and sum patterns of fed input signals at two output ports, called as ∆ and ∑
ports. This setup of array antennas and coupler in vertical direction is shown in figure
4-2 which is simulated in ADS momentum software‟s layout tool. After designing the
setup, S-parameters, far field patterns and antenna parameters of ∆ and ∑ are analyzed
and are given in figures 4-3, 4-4, 4-5, respectively. By using ∆ and ∑ pattern equations
and values of θ from 0 to 30 degrees, absolute amplitude values and phases have been
calculated as given in table 4-1. As shown in figure 4-4, in ADS far field simulation,
using these table values, ∆ and ∑ ports were excited and beam was observed to be
moved from 0 to 30 degrees as values of θ varies from 0 to 30 degrees (phi=90),
respectively, with approximately ±30 error at some θ values. As shown in figure 4-5,
maximum gain obtained is 9.47dBi and directivity 10.99 dBi.
32
Table 4-1: Calculated absolute amplitude and phase of ∆ and ∑ from equations (2-1 and 2-2).
θ [deg.] ∑ 𝐀𝐦𝐩𝐥𝐢𝐭𝐮𝐝𝐞 ∑ 𝐏𝐡𝐚𝐬𝐞 ∆ 𝐀𝐦𝐩𝐥𝐢𝐭𝐮𝐝𝐞 ∆ 𝐏𝐡𝐚𝐬𝐞
0 2 0 0 0
-15 1.667 -27.95 0.9375 62.04
15 1.667 27.95 0.9375 -62.04
-30 1.1756 -54 1.618 36
30 1.1756 54 1.618 -36
Figure 4-2: ADS layout design of ∆ - ∑ Pattern, circuit 1 (theta axis) .
33
Figure 4-3: S-parameters of ∆ and ∑ ports, simulated in ADS layout
a) 2D gain and Radiated Power plots at theta=𝟎𝟎
34
b) 2D gain and Radiated Power plots at theta=−𝟏𝟓𝟎
c) 2D gain and Radiated Power plots at theta=+𝟏𝟓𝟎
Figure 4-4: Far field patterns at different applied theta values.
Figure 4-5: Antenna parameters
35
Simulated ADS layout design has been fabricated for experimental results to find out
the DOA in theta axis. Let‟s call this design as circuit1. From ADS layout, gerber file
was exported in order to fabricate the design on selected RT Duroid 5880 material
(𝜀𝑟 = 2.2, 𝑡𝑖𝑐𝑘𝑛𝑒𝑠𝑠 = 1.575𝑚𝑚). Exported file was given to PCB designing
machine for etching. This fabricated circuit is shown in figure 4-6 with SMA
connectors soldered from back side. Later this circuit was tested in Anechoic Chamber
of Sabanci University, SUNUM department for measured results. In this regard, a horn
antenna was used as a transmitting antenna and constructed circuit used as receiving of
10GHz signal from transmitting horn antenna. This setup is shown in figure 4-7.
Further, using Agilent Network Analyzer (up-to 50GHz), S-parameters and ∆ & ∑
patterns have been measured which later plotted by importing in Matlab and are shown
in figures 4-8 and 4-9 respectively. Having ∆ and ∑ patterns of experimental setup,
angle of arrival in θ-axis can be estimated. For this purpose a Matlab code is written in
which, measured ∆ and ∑ patterns are imported and used in following equation (4-1)
then by using AOA equation, angle of arrival has been found, from -40 to +40 degrees
as expected with some minor rms error of less than 5 degrees. These estimated values
of angle of arrival of received signal v.s actual transmitted signal angles are plotted in
Matlab from 0 to 40 degrees and are shown in figure 4-10. Note that written Matlab
code for this work is given in appendix B.
𝐸𝑥 = 𝐸𝜃𝐶𝑜𝑠𝜃𝐶𝑜𝑠∅ − 𝐸∅𝑆𝑖𝑛∅ (4-1)
Figure 4-6: Difference – Sum Pattern circuit 1 fabricated (theta axis)
36
Figure 4-7: Testing the circuit in Anechoic chamber with Horn transmitting antenna and
fabricated circuit as receiving
Figure 4-8: Measured S-parameters of ∑ and ∆ ports, respectively
37
Figure 4-9: Measured normalized ∆ and ∑ patterns of circuit 1
Figure 4-10: Measured Angle of Arrival of received signal of circuit1 (theta axis)
38
Same circuit has been used to get the 3D radiation pattern from theta = -90 to +90 and
phi=0 to 180 degrees. Using this 3D radiation patterns of difference and sum ports in
Matlab, AOA has been observed from -40 to +40 in theta axis at each value of phi = 0
to 180 with step size of 10. Note that in every step, each phi value has been put
constant and DOA has been observed. Figure 4-11 shows the different plots of
estimated AOA in theta axis at each phi value. Against each phi value, rms error has
been calculated for the performance measurement of AOA in theta axis. Since this
circuit works well to find DOA up-to 400 with rms error less than 5 degrees, so this
rms error at each phi value (180 to 0 deg.) has been determined and shown in figure 4-
12. In order to check the performance of this circuit above 40 degrees, rms error has
been calculated by choosing AOA as -600 to +600 and -800 to +800 at each constant
phi value. This performance is shown in figure 4-13.
a) phi = 180 to 110
b) phi = 100 to 30
39
c) phi=20 to 0
Figure 4-11: Plots of estimated AOA -𝟒𝟎𝟎 to 𝟒𝟎𝟎 in theta axis at different phi value.
Figure 4-12: RMS error for measured DOA in theta axis (-𝟒𝟎𝟎 to +𝟒𝟎𝟎).
Figure 4-13: RMS error at different DOA ranges in theta axis.
40
4.3 Estimating DOA in ∅ axis
Similarly like previous circuit, another circuit (circuit 2) which is at 900 than circuit 1
has been designed to obtain DOA in ∅ axis. First, it is designed in ADS layout and
simulated for desired results as did for circuit 1 and then fabricated for practical
results. ADS layout design of this circuit 2 is shown in figure 4-14. Its simulated S-
parameters, far field patterns and antenna parameters are shown in figures 4-15, 4-16,
4-17. In ADS far field simulation, using table 4-1 values, ∆ and ∑ ports were excited
and beam was observed to be moved from 0 to 30 degrees as values of θ varies from 0
to 30 degrees (phi=90), respectively, with approximately ±30 error at some θ values.
As shown in figure 4-17, gain obtained is 8.89 dBi and directivity 10.13dBi. These
simulated results again are in satisfactory range. Later this circuit has been fabricated
on same substrate RT Duroid 5880 (𝜀𝑟 = 2.2, 𝑡𝑖𝑐𝑘𝑛𝑒𝑠𝑠 = 1.575𝑚𝑚). This
fabricated circuit is shown in figure 4-18 with SMA connectors soldered from back
side. Later the circuit was tested in Anechoic Chamber for measured results in phi
axis. Further, using Agilent Network Analyzer (up-to 50GHz), S-parameters and ∆ &
∑ patterns have been measured which later plotted by importing in Matlab and are
shown in figures 4-19 and 4-20. Having, ∆ and ∑ patterns of experimental setup, angle
of arrival in phi axis can be estimated like circuit 1. Similarly as done for circuit 1, a
Matlab code is written for this task and angle of arrival from -40 to 40 degrees with
rms error of less than 5 degrees has been observed. These values of estimated angle of
arrival of received signal v.s actual transmitted signal angles are plotted in Matlab
from 0 to 40 degrees and are shown in figure 4-21. Note that written Matlab code for
this work is same as given in appendix B.
41
Figure 4-14: ADS layout design of ∆ - ∑ Pattern, circuit 2 (horizontal)
Figure 4-15: S-parameters of ∆ and ∑ ports, simulated in ADS layout
42
a) 2D gain and Radiated Power plots at theta=𝟎𝟎
b) 2D gain and Radiated Power plots at theta=−𝟏𝟓𝟎
c) 2D gain and Radiated Power plots at theta=+𝟏𝟓𝟎
Figure 4-16: Far field patterns at different applied theta values.
43
Figure 4-17: Antenna parameters
Figure 4-18: Difference – Sum Pattern circuit 2 fabricated (phi axis)
44
Figure 4-19: Measured S-parameters of ∑ and ∆ ports, respectively (circuit 2)
45
Figure 4-20: Measured normalized ∆ and ∑ patterns (circuit 2)
Figure 4-21: Measured Angle of Arrival of received signal of circuit2 (phi axis)
46
As done for theta axis, same circuit 2 has been used to get the 3D radiation pattern in
anechoic chamber. Using this 3D radiation pattern of difference and sum ports in
Matlab, AOA has been observed same from -40 to +40 in phi axis as expected at each
value of theta = 0 to 180 with step size of 10 (now theta values have become as phi
values and hence we call it as AOA in phi axis while phi values have become theta
values: 180 to 0 deg.). Note that in every step, each theta value has been put constant
and DOA has been observed. Also note that, in both axis (θ,∅) obtained DOA is -40 to
40 because both circuits are same but placed at 900apart. Figure 4-22 shows the
different plots of estimated AOA in phi axis at each theta value. Against each theta
value, rms error has been calculated for the performance measurement of AOA in phi
axis as done for theta axis. Since this circuit works well to find DOA up-to ±400 with
rms error less than 5 degrees, so this rms error at each constant theta value (180 to 0
deg.) has been determined and shown in figure 4-23. In order to check the performance
of this circuit above 40 degrees, rms error has been calculated by choosing AOA as -
600 to +600 and -800 to +800 at each constant theta value. This performance is
shown in figure 4-24.
Obtained DOAs in both axis (theta and phi) at fixed phi value are together plotted and
shown in figure 4-25.
a) theta = 180 to 110
47
b) theta = 100 to 30
c) theta = 20 to 0
Figure 4-22: Plots of estimated AOA (-𝟒𝟎𝟎 to 𝟒𝟎𝟎) in phi axis at different theta values.
48
Figure 4-23: RMS error for measured DOA in phi axis (-𝟒𝟎𝟎 to +𝟒𝟎𝟎).
Figure 4-24: RMS error at different DOA ranges in phi axis.
49
Figure: 4-25: Estimated DOA in both axis (theta and phi) at fixed phi value (0 deg.).
Moreover, as shown in figure 4-26, another circuit which combines all these four
antennas into one system also has been simulated in ADS which gives over all system
design. Working principle of this design is that we have two sections of same ∆ - ∑
circuit but in each section both antenna elements are being fed by different locations
which result in opposite current directions. So this thing has been compensated by
giving one of the elements a phase shift of 1800which has been calculated from below
equation (4-2). Therefore, one of the elements transmission line must be 10mm longer
than the other element‟s transmission line.
∆L = ∆∅
𝛽=
∆∅
2𝜋 𝜆𝑔 =
𝜋
2𝜋
𝜆𝑎𝑖𝑟
𝜀𝑟= 10mm (4-2)
50
Figure 4-26: Overall system design
Each section can find the DOA in one axis (theta) easily using the procedure as done
previously. In order to find the DOA in other axis (phi), we need to take the sum
outputs (∑1,∑2 ) and apply as two inputs to another coupler in order to take out the
difference and sum (∆3 ,∑3). Note that in this case one of the applied summation
pattern (∑1 𝑜𝑟 ∑2 ) must be multiplied by 𝑒−𝑗𝑘𝑑𝑠𝑖𝑛𝜙 in order to scan in other axis.
Having this information, ∑1 and ∑2 patterns are given below in equations (4-3 and 4-
4) from which ∑3, and ∆3 pattern equations have been formed by simply adding and
subtracting ∑1 and ∑2 and are given in equations (4-5 and 4-6). By taking ratio ∆3 to
∑3, DOA angle in phi axis has been driven by performing some mathematical
iterations and is given in equation (4-7).
∑ 1 = 1 + e−jkdsin θ (4-3)
∑ 2 = 1 + e−jkdsin θ e−jkdsin ϕ (4-4)
∑ 3 = ∑ 1 + ∑ 2 (4-5)
∆𝟑= ∑ 1 − ∑ 2 (4-6)
𝜙 = sin−1 𝜆
𝜋𝑑tan−1 𝚫𝟑
∑ 3 (4-7)
51
5. Conclusion
Direction of arrival (DOA) system having application in radar, sonar, military,
acoustic, communication and medical imaging is being widely studied in various
communication fields. Researchers are trying to face the requirements of high
efficiency, proper functionality and compactness for radars and sensors. By keeping
this idea in mind, this thesis work has been carried out to research in DOA system
design in order to obtain DOA of received signal using difference (∆) and sum (∑)
patterns in two axis.
In this thesis work, a direction finding system has been implemented to estimate the
DOA of received signal in x-band. Proposed system consists of microstrip patch
antenna array of two elements spaced 0.6 λ and 1800 hybrid rat race coupler which
generates the ∆ and ∑ patterns of two received signals according to equations (2-1 and
2-2). For array part, microstrip patch antenna has been designed for reception of RF
signal at 10GHz operating frequency while as part of ∆ and ∑ pattern, rat race coupler
designed and optimized for accurate results at central frequency. Antenna array and
coupler were integrated and ∆ - ∑ patterns obtained, in vertical and horizontal
directions, by constructing two separate same design circuits, one for finding AOA in
theta axis and other circuit for finding AOA in phi axis. Using these ∆ - ∑ patterns,
angle of arrival (AOA) has been estimated by using equation (2-3). This task first has
been analyzed numerically using ∆ - ∑ equations in Matlab, then designed in ADS
layout and simulated. Obtained ADS simulated S-parameters, far field ∆ - ∑ patterns
and antenna parameters are in acceptable range.
Later simulated designs of both circuits were fabricated on RT Duroid 5880 (𝜀𝑟 = 2.2,
𝑡𝑖𝑐𝑘𝑛𝑒𝑠𝑠 = 1.575𝑚𝑚) substrate by machine etching process. Fabricated circuits
were tested in Anechoic Chamber using a horn antenna as a transmitter and
constructed circuits as receiving element at 10GHz frequency of operation. Each
circuit‟s 3D (θ= -90 to +90, 𝜙 = 180 𝑡𝑜 0 degrees) ∆ and ∑ patterns were taken as
measured data. Experimentally obtained data was imported in Matlab for analysis of
DOA. Measured S-parameters and far field ∆ - ∑ patterns are very close to simulated
results. From ∆ - ∑ patterns of each circuit, DOA has been estimated for both axis
(theta and phi) by using the equation (2-3). Both circuits are able to find angle of
arrival from -40 to +40 degrees in their respective axis (circuit 1 for theta axis and
circuit 2 for phi axis). RMS error also has been calculated at each constant 3D phi
value for measured data of DOA from -90 to +90 and found as less than 5 degree of
rms error for both circuits at -40 to +40 while it increases more as we go above the 40
degrees. This suggests that designed DOA works well for 0 to ±40 degrees. By looking
52
at all simulated and measured results, proposed system design of DOA works in
satisfactory range which in result fulfills the purpose of this thesis work.
As a future work, to improve more results, substrate material can be chosen such that
its thickness is lower than this thesis substrate thickness because thicker material
introduces more losses at higher frequencies such as x-band frequency spectrum.
Moreover, the increase in number of antenna elements can be one possible way
towards further improvement. However, this will increase the gain and so the
operation range, however size of the antenna array will become significantly large.
Another noticeable improvement in results can be achieved if we use another antenna
such as dipole, instead of patch antenna because of its narrow beamwidth.
53
6. Appendices
6.1 Appendix A
Matlab code for numerically analysis of Difference – Sum Pattern and Angle of
Arrival
Note that 2D gain pattern values obtained from ADS simulations of single 10GHz
patch antenna, can be saved in Microsoft excel (.xlx) file.
clear all;
clc;
close all;
f=10*10^9;
v=3*10^8;
lembda=v/f;
k=(2*pi)/lembda;
d=0.5*lembda;
[n t] = xlsread('D:\Users\SUUSER\Desktop\1elementGainPattern.xlsx');
theta = n(1:62,1);
gainDB = n(1:62,2);
delta=pow2db(abs(1-(exp(-j*k*d*sin(theta)))));
summation=pow2db(abs(1+(exp(-j*k*d*sin(theta)))));
delta(31,1)=-22;
delta(32,1)=-22;
funcOfDelta = delta+gainDB;
funcOfSummation = summation+gainDB;
normalizedDelta=funcOfDelta-max(funcOfDelta);
normalizedSummation=funcOfSummation-max(funcOfSummation);
figure;
plot(theta,normalizedDelta,'s-b');
xlabel('Angle [deg.]');
ylabel('Received Power [dB]');
axis([-90 90 -50 0]);
hold on
plot(theta,normalizedSummation,'-r');
legend('Delta','Sum');
54
%finding angle of arrival from 0 to 90
sum1Power=db2pow(normalizedSummation(32:62));
diff1Power=db2pow(normalizedDelta(32:62));
deltaToSumRatio=(diff1Power/sum1Power);
tanInvOfRatio=atan(deltaToSumRatio);
DOA=rad2deg(asin((lembda/(pi*d))*tanInvOfRatio));
theta11=theta(32:62);
figure ;
plot(theta11, DOA);
xlabel('Angle [deg.]');
ylabel('Direction of Arrival[deg.]');
55
56
6.2 Appendix B
Matlab code estimating theta/phi axis using difference – sum patterns
clear all;
clc;
close all;
c=3*10^8;
f=10*10^9;
lembda=c/f;
d=0.6*lembda
[n1 t1] = xlsread('D:\Users\SUUSER\Desktop\ckt1RadPattern1SumPort.xlsx');
[n2 t2] = xlsread('D:\Users\SUUSER\Desktop\ckt1RadPattern2SumPort.xlsx');
[n3 t3] = xlsread('D:\Users\SUUSER\Desktop\ckt2RadPattern1DiffPort.xlsx');
[n4 t4] = xlsread('D:\Users\SUUSER\Desktop\ckt2RadPattern2DiffPort.xlsx');
angle1 = n1(1:37,1);
sum1Amp = n2(1:37,2);
max_sum1Amp =max(sum1Amp)
sum1AmpNormalized=sum1Amp-max_sum1Amp;
diff1Amp = n4(1:37,2);
max_diff1Amp = max(diff1Amp)
diff1AmpNormalized=diff1Amp-(max_diff1Amp);
figure ;
plot(angle1,sum1AmpNormalized,'-r');
xlabel('Angle (degrees)');
ylabel('Received Power[dB] (ckt 2)');
grid on;
hold on;
plot(angle1,diff1AmpNormalized,'s-b');
legend('Sum','Delta');
sum1Power=db2pow(sum1AmpNormalized(19:37));
diff1Power=db2pow(diff1AmpNormalized(19:37));
angle11=angle1 (19:37);
deltaToSumRatio=(diff1Power./sum1Power);
tanInvOfRatio=atan(deltaToSumRatio);
AOA=rad2deg(asin((lembda/(pi*d))*tanInvOfRatio));
figure ;
plot(angle11,AOA, 's-b');
xlabel('Transmitted Signal Angle[deg.]');
ylabel('Received Signal Angle of Arrival[deg.] (ckt 2)');
grid on;
57
hold on;
error=(angle11-AOA)
plot(angle11,error, '-r');
grid on;
legend ('Estimated DOA ', 'Error');
sum1Power2=db2pow(sum1AmpNormalized);
diff1Power2=db2pow(diff1AmpNormalized);
deltaToSumRatio2=(diff1Power2./sum1Power2);
tanInvOfRatio2=atan(deltaToSumRatio2);
AOA2=rad2deg(asin(lembda/(pi*d)*tanInvOfRatio2));
figure ;
plot(AOA2(19:37),deltaToSumRatio2(19:37), 's-b');
xlabel('Arrival angle[deg.]');
ylabel('Delta/Sum (ckt 2)');
grid on;
6.3 Appendix C
Finding Difference – Sum absolute and phase values using equations (2-1 and 2-2)
in order to excite the ports of ADS
clear all;
clc;
close all;
c=3*10^8;
f=10*10^9;
lembda=c/f;
d=0.6*lembda
d1=0.6*lembda;
k=(2*pi)/lembda
kd=k*d;
theta1= -pi/4:pi/12:pi/4;
phi1= 0
sum1=1+exp(-j*(kd)*sin(theta1));
sum1abs=abs(sum1);
sum1phase=rad2deg(phase(sum1));
delta1=1-exp(-j*(kd)*sin(theta1));
delta1abs=abs(delta1);
delta1phase=rad2deg(phase(delta1));
sum2= (1+exp(-j*(kd)*sin(theta1)))*(exp(-j*k*sin(phi1)));
sum2abs=abs(sum2);
sum2phase=rad2deg(phase(sum2));
58
delta2=(1-exp(-j*(kd)*sin(theta1)))*(exp(-j*k*sin(phi1)));
delta2abs=abs(delta2);
delta2phase=rad2deg(phase(delta2));
sum3=(1+exp(-j*(kd)*sin(theta1)))*(1+exp(-j*k*sin(phi1)));
sum3abs=abs(sum3);
sum3phase=rad2deg(phase(sum3));
delta3=(1+exp(-j*(kd)*sin(theta1)))*(1-exp(-j*k*sin(phi1)));
delta3abs=abs(delta3);
delta3phase=rad2deg(phase(delta3));
59
7. References
[1] A.Vesa, G.Iozsa, “Direction – of – Arrival Estimation for Uniform Sensor Arrays”, IEEE
Electronics and Telecommunications (ISETC), 2010.
[2] Ryo Tanaka, Eisuke Nishiyama, and Ichihiko Toyoda, “A Mono-Pulse DOA Estimation
Antenna Integrated with RF Amplifiers and Detection Circuits”, IEEE Antennas and
Propagation Society International Symposium (APSURSI), July 2014.
[3] M. Rubsamen and A. Gershman, “Direction – of – Arrival for Nonuniform Sensor Arrays:
From Manifold Separation to Fourier Domain MUSIC Methods,” IEEE Transactions on
Signal Processing, vol. 57, no. 2, pp. 588 – 599, February 2009.
[4] L. Yip, K. Comanor, J. C. Chen, R. E. Hudson, K. Yao, and L. Vandenberghe, “Array
Processing for Target DOA, Localization, and Classfication Based on AML and SVM
Algorithms in Sensor Networks,” Information Processing in Sensor Networks, Lecture Notes
in Computer Science, Vol. 2634, pp. 269-284, Springer, 2003.
[5] Warren L.Stutzman & Gary A. Thiele, “Antenna Theory and Design”, edition 2, John Wiley &
Sons Inc, Newyork 1998.
[6] Hirotoshi Sakai, Eisuke Nishiyama, and Ichihiko Toyoda, “Direction of arrival estimating
array antenna”, Proceedings of ISAP2012, Nagoya, Japan, 2012.
[7] Constantine A. Balanis, “Antenna Theory, Analysis and Design”, edition 2, John Wiley &
Sons Inc, Newyork, 1997.
[8] Telecom Hall, „What is Antenna‟, (http://www.telecomhall.com/what-is-antenna.aspx),
November 20, 2014.
[9] Beamwidths and Sidelobe Levels, „Antenna Fundamentals‟, (http://www.antenna-
theory.com/basics/radPatDefs.php), November 24, 2014.
[10] Jagdish. M. Rathod, “Comparative Study of Microstrip Patch Antenna for Wireless
Communication Application”, International journal of innovation, Management and
Technology, Vol 1,No.2,2010.
[11] Kin-Lu Wong, “Compact and Broadband Microstrip Antennas”, Jon Wiley & Sons, Inc.,2002
[12] D.M.Pozar and B.Kaufman,”Increasing the Bandwidth of a Microstrip Antenna by Proximity
Coupling”, Electronic Letters, Vol- 23, pp [12-14] April-1987.
[13] G.A. Desschamps, “Microstrip microwave antennas”, presented at the 3d USAF Symposium
on Antennas, 1953.
[14] J.Q. Howell, “Microstrip antennas”, IEEE APS Int. Symposium. Digest, pp. 177-180, 1972.
[15] Inder J.Bahl, Parkash Bhartia, Stanislaw S. Stuchly, “Design of microstrip antennas Covered
with a Dielectric Layer”, IEEE Trans. Antenna Propagation, vol. AP-30, no.2, pp.314-318,
March 1982.
[16] Microstrip Patch Antenna Calculator, (http://www.emtalk.com/mpacalc.php), July 01,2014.
60
[17] E. levine, G. Malamud, and S. Shrikman, “A study of microstrip array antennas with the feed
network”, IEEE Trans. Antennas Propagation, vol. 37, pp 426-434, April 1989.
[18] Antenna Arrays, „Antenna Theory‟, (http://www.antenna-
theory.com/arrays/main.php#phased), November 2014.
[19] R.E. Munson, “Conformal microstrip antennas and microstrip phased array”, IEEE Trans.
Antenna Propagation, vol. AP-22, pp. 74-78, 1974.
[20] J.John Huang, “A technique for an array to generate circular polarization with linearly
polarized elements”, IEEE Trans. Antenna Propagation, vol. AP-34, pp. 1113-1124, Sept.
1986.
[21] Wu, Y., Y. Liu, and S. Li, \Dual-band modified Wilkinson power divider without transmission
line stubs and reactive components", Progress In Electromagnetic Research, Vol. 96, 393-411,
2009.
[22] D. M. Pozar, john, "Microwave Engineering," 2nd ed., Wiely & sons, pp. 160-163, 1998.
[23] T. Johnson and H. Neill, "Complete Mathematics", Hachette UK Company, pp.218-220, 2010.
[24] EL entsd wireless A. D. Polyanin and A. I. Chernoutsan, "A Concise Handbook of
Mathematics, Physics, and Engineering Sciences", CRC Press Taylor and Francis Group, pp.
48, 2011.