Post on 02-Jun-2018
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 1/14
1
Automatic tool measurement manual (Tool probe)
O8000 PROBE CUSTOM CALIBRATIOM
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 2/14
2
As setting value can be changed during machine transfer, new equipment must confirm
certainly
Because there is danger of crash, use dry run, single block when confirm first time (par
6!!"#)$%ecute more once as follows
&rogram in machine can be different from this
' &repare standard tool (*A 6+ high spin tool with end point is good)
-elect mode by $dit, and call .!!! program (detail / page ' reference) *f setting
value amendment need, value is change
0 1hange mode by Auto (2emory) and do e%ecution 1ycle start
3 2ove to stylus center and a%is is stopped in 42!!5
-elect mode 7og 8 by 9andle convert and move to stylus top portion about '!+'
mm position
6 1hange mode selection by Auto and do auto e%ecution 1ycle start again
At month, do trial about once
M200 AUTOMACTIC TOOL LENGTH MEASURMENT
' 1hange to 2* mode and e%change by tool to measure
After input 2!!, do e%ecution with 1ycle start button *f amendment of value
need, value is change (detail / page )
M300 AUTOMATIC TOOL LENGTH BREAK MEASUREMENT
' -elect 2* mode and e%change by tool to measure
After input 20!!, press 1ycle start button *f amendment of value need, value is
change (detail / page 0)
M400 SEMIAUTOMATIC MEASUREMENT
' 1hange 2* mode and e%change by tool to measure
*nput 23!! and press 1ycle start button (detail / page 3)
0 2ove to -tylus center and a%is is stopped in 42!!53 2ode select 7og 8 9andle convert and move to -tylus top portion about '!+
'mm position -elect Auto mode and press 1ycle start again
1.:T$:T
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 3/14
3
' .!!! 1alibration setting -tandard; Absolute
2!! Automatic tool length measurement
0 20!! Automatic tool length breakagemeasurement
3 23!! -emiautomatic measurement
2!! Automatic <ork = setting
6 2easurement application
# Alarm messages
-ervice and maintenance
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 4/14
4
STANDARD CALIBRATION
>.!!! (?en T-#? 1alibration)
@'@=! "0 +a%is position (machine position)
@!@3!@! "3 C+a%is position (machine position)
@!(D Tool changeD)
@!!@0"0C"3 (,C measurement position for -tylus)
@!!@0=+!
2!!(-TCEF- .: '!22 A&&?.A19)
"!6G!0 ( -F?HA1$ BA1I+.HH *-TA:1$)
"!#G' ( +A*- 2.J$ JAEF$ + T.F19)
"G'!! ( ?A&* A&&?.A19 &.- *: = )
"6G! ( Fnder *A '!mm )
"#G! ( .ver *A'!mm"G6! ( 2A 1FTT$? *A2$T$? )
"G0 ( '(A), (B), 0(1 ) <.?I .HH-$T TC&$ )
"0!G
"0'G! *:19;2$T?*1 -T.?$ ATA
2'
:'( E$:@T9 1AE*B?AT*.:)
@6&'I!K'
@'@=!
@!2!
:( *A2 1AE)
"0!'G'( A*-) +A*- -$E$1T
@6 & -6 I'#=+' ( -6 L *A -tandard T..E)
:0( C *A2 1AE )
"0!'G(C A*-) C+A*- -$E$1T
@6 & -6 I'# =+' -+T..E *A I+-TCE -*=$
2!
This does setting when install first time
isk -tylus
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 5/14
5
ABSOLUTION CALIBRATION SETTING
>.!!!(?$: T-#? 1AE*B?AT*.:)
@'@=! "0+ a%is position (machine postion)
@!@3!@! "3+ C a%is position (machine position)
@!
(D T..E 19A:@$ D)
@!!@0"0C"3 (, C measurement position for -tylus )
@!!@0=+!
2!!(-TCEF- .: '!22 A&&?.A19)
"!6G!0 (-F?HA1$ BA1I+.HH *-TA:1$)
"!#G' (%+a%is move value + touch )
"G! (?A&* A&&?.A19 &.- *: =)
"6G!! (*A '!mm )
"#G!! (over dia '!mm )
"G6! (2A 1FTT$? *A2$T$?)
"G0 (<.?I .HH-$T TC&$ '(A), (B), 0(1 ) )
"0!G I
"0'G! *:19;2$T?*1 -T.?$ ATA
2'
:'(E$:@T9 1AE*B?AT*.:)
@6 &' I'! K' (I'! -tandard T..E E$:@T9)
@'@=!
@!
2!
:( *A2 1AE)
"0!'G'( A*-) +A*- -$E$1T
@6 & -6 I'# =+' -+T..E *A I+-TCE -*=$
:0( C *A2 1AE )
"0!'G(C A*-) C+A*- -$E$1T
@6 & -6 I'# =+' -+T..E *A I+-TCE -*=$
2!
This does setting when install first time
isk stylus
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 6/14
6
AUTOMATIC TOOL LENGTH MEASUREMENT
2!!TM-MK
$%L 2!! T'!
2!! T'! -'
TL .ffset number (if unused, tool number and offset number are same) :oticeL*f use waiting tool, input T+no certainly
-L Hlat end mill diameter siNe (.ver ia ''mm) ?everse after move to bed
inside as -;
KL istance that can move than setting value to .!!! more by = shaft *f
unused recogniNe by default value !mm
Fnder ia '! mm .ver ia '!mm
- (siNe)
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 7/14
7
AUTOMATIC TOOL LENGTH BREAKAGE MEASUREMENT
20!!TM-M9
$%L 20!! T'!
20!! T'! -'
TL .ffset number (if unused, tool number and offset number are same) :oticeL*f use waiting tool, input T+no certainly
-L Hlat end mill diameter siNe (.ver ia ''mm) ?everse after move to bed
inside as -;
9L Tool damage range *f unuse, recogniNe by default value !mm
- (siNe)
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 8/14
8
SEMIAUTOMATIC MEASUREMENT
23!!TM-M
$%L 23!! T'!
23!! T'! -'
2ove by 7og 8 9andle
-
'!+'mm
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 9/14
9
AUTOMATIC WORK Z- SETTING
2!!TM-MB
$%L 2!! T -'
2!! T B! -
TL .ffset value (work coordinate system setting tool)-L <ork coordinate number (-'+-6 +O@3+@, -'!'+-'3 +O@3'&'+
@3'&'3)
BL Block gauge or presenter height ( BP application possibility)
BP
=
<ork piece
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 10/14
10
MEASUREMENT APPLICATION
' Hull tool setting program (length only)
1an measure all tool at once>.'03 Eength value ($%ample)
26T'2!!T' 9'L
26T
2!!T 9L !
26T
2!!T 9L '
2!
>
Tool setting included in the part program&rocess during processing can finish and measure And do heat displacement
revisions
>.!!!
@'@=!@3!@!
26T'
2!!T' Tool :o ' measurement
@!@3@!QCQ
@309'=!
20!!T' Tool breakage check
@'@=!
@3
2!
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 11/14
11
ALARM MESSAGES
' 0!' Hormat error
1auseL Fnused character that specify or mistake input
ActionL 1onfirm again and re+input and e%ecution
0! &robe open
1ause 'L &resent measurement tool is long case more than "6 setting valueActionL AdRust "6 value according to tool length (detail page ')
'! 1ause L irty thing accumulates in connection region of T-#? measuring
instrument
ActionL 1lean connection portion so that chip does not accumulate
0 0! &robe fail
1auseL 2easurement tool does not touch in -tylus
ActionL -et point K value use or change (detail page ')3 0! Broken tool
1auseL *n case tool is broken
ActionL 1onfirm damage of tool and e%change tool (detail page ')
.ther alarm message consult with machine brand
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 12/14
12
EXCHANGE WEAK LINK METHOD
' Throw away weak link and damaged bolt 3 1onnect built -tylus using wea
Eink and mood volt B
Assemble new weak link like picture
Assemble using wrench to measuring
*nstrument Hinally, assemble connection
ring using 1 bolt on -tylus holder
bottom
0 <ith mood volt A isk -tylus 8 -tylus
holder assemble
<eak link damage e%ample
-tylus horiNontality (e%ample + a%is)
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 13/14
13
-ide horiNontality
$%L +a%is '
!!!mm
B A (<asher)
*f tighten A screw, star llreoseu is been slanted for ' direction 8 A if do loosen for
directions be slanted
1ontrol of B screw ends to A screw and act role that do to be not loosen
Hront side horiNontality (e%ample C+a%is)
8/10/2019 TS27R - Blum
http://slidepdf.com/reader/full/ts27r-blum 14/14
14
B A
!!!mm '
*f tighten A screw, star llreoseu is
been slanted for ' direction 8 A if do
loosen for directions be slanted -crew tightens each other as do not untie and e%ecute
1alibration (see page ')
K;AK' @ap occurs to work piece
A' 1onfirm indicator -tylus horiNontality *f is !!!mm something wrong, adRust
horiNontality again After adRust horiNontality, e%ecute 1alibration (.!!!)
K &robe became broken
A <hole probe broken or measurement region (weak link / page ) is broken was
checking <hole probe damage / inquiry by telephone