Post on 06-Mar-2015
National Glass can supply glass and fittings
packages for toughened door assemblies,
sliding doors, facades and shopfronts,
spider wall systems, point fixings or stainless
steel stand offs, balustrading, pool gates,
fences and shower screen enclosures.
13frameless glass installations
Typical spider fixing.
Type B bottom rail top corner patch toughened entry door – Australia Glass.
80
heavyweight glass chart
Glass types Thickness (mm)
Clear 10/12/15/19/25
Grey 10/12
Bronze 10/12
Green 10/12
Blue 10/12
Acidetched 10/12
Low-iron 10/12/15/19
Sunergy®low-E 10
Please check on availability upon request.
Typical floor spring.
Typical corner patch fitting.
81
pivot doors
Pivoting glass doorsandassociatedpanelssuchassidelitesandhighlightsmustbeaminimumof10/12mmtoughenedsafetyglass(PleasecheckwithAS1288todetermineactualthicknessrequired).Thesedoorsarethemostcommonframelesstypeusedincommercialandresidentialapplications.Thedoorsuseeitheraconcealedtoporbottomselfclosermechanismwithapivotpointconnectingtoadiscretemetalpatchfittingatthetopandbottomcornersofthedoororalternatively,afullwidthmetaldoorrailcanalsobeused.
pivot door types
Corner patch fittings TypeBandC
Full length rails TypeAandB
Offset pivot doors TypesA,BandC
Centre fix pivot doors TypesA,BandC
G-tech pivot doors Seepages86-87
See Diagram 13.1.
corner patch fitting doors
ShownasType BcombinationandType CdoorsonDiagram13.1,patchfittingsaresimplyaboltthroughglassmetalfittingrequiringacornercutoutandholeintheglass.Thesediscretepatchesprovideasleekandcleanframelesslook,idealforshopdisplays.
Alockbodypatchfittingcanalsobeinstalled.Thepatchbodycoversareavailableinavarietyoffinishesincludinganodised,powdercoated,platedbrassandstainlessfinishes.
Maximumdoorsizesusing10/12mmthicknessglassis2400mmx1000mm.15mmglassthickness2400mmx900mm.Biggersizedoorsshoulduseatopandbottomfulllengthrail.Pleasenotethatwindloadingandotherloadingconsiderationsmayoverridethesizesandthicknessesnotedabove.Pleasecheckwiththeappropriatestandards.
full length rail doors
ShownasType AandcombinationType BdoorsonDiagram13.1,thesemetalrailsareclampedontotheglassedge.Noholesorcutoutsrequired.Themainfeaturesoftherailaretoactasa‘kickplate’tolessonchanceofglassbreakageandforoversizedoors,wherethepatchfittingisnotsuited.Railbodycoversareavailableinavarietyoffinishesincludinganodised,powdercoated,platedbrassandstainlessfinishes.
Type A top and bottom rail toughened entry doors – Glasstech Cairns.
Type C top and bottom corner patch toughened entry door – Australia Glass.
82
diagram 13.1: frameless pivot door and entry types
type A – full length top and bottom rails
type B – top corner patch fittings and full length bottom rails
type C – top and bottom corner patch fittings
83
highlite glass fin design
Someframelessdoorentrytypesrequirestabilisingtoughenedfinstoreducedeflectioncreatedbytheloadsactingontheentry.Theseincludeexternalandinternalwindloading,humanimpactandthemotionofthedoorduringoperation.
Minimum design requirements are:
0 Finsshouldalwaysbemechanicallyfixedtothestructurebymeansofabacktobacksteelorstainlesssteelfinbracket;
0 Structuralfinsshouldnotbelessthan12mminthicknessandshouldalwaysbetoughened(see also Diagram 13.3);
0 Internal entries–Whenthewidthofthesidelite(A)plustheheightofthehighlite(B)exceedsatotalof1000mmastructuralfinisrequired(see also Diagram 13.2);
0 External entries–Awindloaddesignshouldalwaysbecarriedouttodeterminethicknessandwidthoffin.
diagram 13.2
Typical cantilevered fin with bolt through back to back stainless steel head mounted fin bracket – Qld Glass.
Cantilevered glass with bolt through stainless steel head mounted bracket and 2 way spider fixing for face glass connection – Glass Solutions.
Offset pivot detail.
12mm grey toughened door with offset pivot..
84
diagram 13.3: cantilever fin detail
0 Withhighlitefindesigns,(X)mustbenolessthan2/3ofthefinwidthrequired.
centre fix pivot doors
Thispivotsystemisusedwhenalargerdoorwidthisrequired.(e.g.greaterthan1000mm).Thepivotpointismovedtowardsthecentreofthedoor.Onepointtobeawareofisthatthedoorglasswillextendoutmoresothananormalpivotingdoorwhenopen.Centrefixbottompatchshownisalsoavailableinrails.
offset pivot doors
Inthispivotsystemthepivotcentreisnotdirectlyundertheglass.Itisoffsettoonesideallowingthedoortoswingback180°,finishingparallelwiththesidelite.Thispivotsystemcanonlyworkonfloorspringsorfreepivotsandadditionallocktroughsarerequiredtoholdthedooropenintheopenposition.Theoffsetbottompatchisasshown,butitisalsoavailableinrails.
pivot door closers
Selfclosingconcealedoverheadclosersandfloorspringclosersarerequiredtopreventthedoorfromopeningorshuttingforcefullyduringnormaluseandhighwindsituations.Differentclosermechanismsortypesallowthedoortoalwaysclose(NHOnonholdopen)toitscorrectpositionandstayclosed,orstayopenataspecificangle(90ºHO–holdopenat90ºangle).Theseclosersaredoubleaction,meaningthatthedoorcanswingfullythrougha180ºangle.
Becauseofthelargevariationofdoorsizesandapplications,theclosersaremanufacturedinvaryingclosingstrengths.Astrongerstrengthspringactionisrequiredwithlargerdoors.Thestrongerspringpreventsthewindfromopeningthedoorandforcesthedoorshut.Thedisadvantageisthatthedoormaybemoredifficulttoopenforsomepeopleormaycontravenedisabilityregulations.
Closerscanbeinstalledoverthetopofthedoorsintheceilinginanaluminiumtransombox(COC–Concealedoverheadcloser)orinthefloor(floorspring).
12mm clear toughened door with centre fix pivot – QLD Glass.
NG166/7 small door pivot sets.
NG131 patch hinge – side hinged.
85
Adoorstopisrecommendedwherethedoorleafisover900mmwide.Thestopshouldbelocatedinthe100ºpositiontopreventdamagetotheCOC.
Floorspringsrequiretheinstallertofixthedeviceinsidethefloor.Floorspringsaregenerallyspecifiedforlargerdoorapplicationsorwhereaceilingmountedcloserisnotpossible.
free pivot doors
NG166/7 small door pivot sets
Pivotdoorscanbeinstalledwithoutselfclosers.However,theyareonlyrecommendedfordoorswithinfrequentuseorshowcases.Itisadvisabletousedoorstopstopreventbreakageordamagetowalls.AnalternativestyleoffreepivotingdoorpatchesistheNG166/7smalldoorpivotset.Thesetopandbottompatchesaresuitedfor8/10/12mmthicknessglassupto60kgindoorglassweight.Theyarefixedtotheheadandsillandswingonewayonly.
NG131 patch hinge – side hinged
Butttypehingetosuit8/10/12mmglassthicknessforglassdoorsupto60kg.Maximumsizedoors2100mmx900mm.Thesedoorsareonlysuitedforfixingintosolidjambframeworkandswingonewayonly.
Free pivot door using NG166/7 small door pivot set – Glass Solutions.
G-tech pivot door system
Adesignalternativetostandardcornerpatchanddoorrailsystems,G-techcomponentsaremadefrom304gradestainlesssteelmaterialwitheitherproudorcountersunkflushglassfixings.
Tosuit10/12mmtoughenedglass,doorleafsizesupto2400x1000mm.
diagram 13.4: G-tech pivot door types
type A
86
G-tech pivot door system – QLD Glass.
Full height rod G-tech pivot door.
Bottom pivot close up – QLD Glass.
87
diagram 13.4: G-tech pivot door types continued
type B type C
type D type E
type F type G
All photos: NG150 series top hung sliding door – C & B Glass.
88
manual sliding doors
There are two manual sliding systems available:
0 NG150 Top hung sliding doors–Thesedoorshavesuspendedrollersfittedtoatoppatchandslideinatrackintheceiling.Afloorguideismountedonthefloorattheslidingendoftheopeningtokeepthedoorplumb;
0 Bottom track–Thesedoorshaverollersfittedinthebottomofarailwhichrollonacontinuousbottomtrack.Thetopguideisacontinuoustopchannelrecessedintotheceiling.Doorstopshavetobefittedtothetopandbottomtostopthedoorsatfullopeningandclosing.
Thebottomtracksystemhasacontinuoustrackrunningthefulllengthoftheopening.Thismayaffectthefloorfinishandmaycreateasteppingproblem.Thetrackwillalsoallowdirtorrubbishtocollectandthedoorpanelmustbesecurelylockedtopreventdirectliftingoutofitsopening.
diagram 13.5: NG150 series sliding door
89
G-tech sliding door system
Adesignalternativetostandardtophungandbottomtrackslidingsystems,G-techcomponentsaremadefrom304gradestainlesssteelmaterial.Tosuit10/12mmtoughenedglass.
Slidingpaneldoorsizesupto2400mmx1200mmor90kg.Glassfixingsavailableineitherproudorcountersunkflushfittings.
diagram 13.6
G-tech sliding door system – QLD Glass.
G-tech sliding door wall mounted.
G-tech door hanger set.
90
bi-fold doors
Thesesystemsprovidefortheopenshopfrontlook.Thepanelsarehingedtogether,foldbackagainsteachotherwhenopenedandstackagainstthewallsateitherendoftheopening.
stacking doors
Theseframelessglassdoorsystemshavebeendesignedsothatshopfrontscanbeleftcompletelyopenduringtradinghoursandsecurelylockedafterhours.Thepanelsslideinatoptrackwitharollersystemandarestackedawayinastorage/stackingbayeitherparalleloratrightanglestothemaintrackorinastackingbaylocatedawayfromtheshopfrontline.Thestackingbayscanalsobelocatedinacupboardsothatthepanelswillbecompletelyoutofview.Pivotdoorscanalsobeincludedinthesystem.
diagram 13.7: bi-fold doors
diagram 13.8: stacking doors
Top and bottom tracks (Morethan2glasspanels)
No tracks (Maximum2glasspanels)
Top and bottom tracks with a pivot door
BMW car showroom – single tier shopfront with full height supporting fin – Bradnams Commercial.
91
glazed walls – single tier
Generally,single tierglazedpanelsarerestrictedbyoriginalglasssheetsizes,tougheningandlaminatingcapabilitiesandAustralianStandards/BCArules.InAustralia,toughenedglassisavailableupto5500mmx2800mmandlaminatedglassisavailableupto5100mmx3210mm.Theseglazedstructuresaregenerallybottomloadedortheglassisdeadloadsupportedbythefloor.Wherethereisarunoralargeopenexpansetobeglazed,glasssupportfinsmayberequiredtopreventpanelsfrombeingblowninorpulledoutduringhighwindloadconditions.
fin support
Finswhicharesiliconeglazedtofacingpanelsasshown,provideafour-sidedsupportorfullyframedsupportforthesefacingpanels.Finsareusedtopreventglassfacingpanelsfromdeflecting,breakingorfallingoutthroughwindloadpressures.AS1288requiresfinswheretwoedgeonlysupportedglazingsareinsufficientincopingwithapplicablewindloads.Glassfinsinmostcasesmustrunthefulllengthofthepanelheightandbechannelglazedormechanicallysecureddependingontheapplication.Finthicknessandwidthisdeterminedbywindload,facingpanelsizeandsiliconejointbitesize.
no fin support
Wherefinsarenotdesiredforappearanceorotherreasons,windloadisacriticalfactorindeterminingglassthickness.Areasnotsubjecttowindload,suchasenclosedshoppingcentres/malls,mayinsomesituationsutilisethistypeofshopfrontdesign.
diagram 13.9: full height fin design
Withfullheightfindesigns,(X)mustbenolessthan2/3ofthefinwidthrequired.
Single tier shopfront with full height supporting fin – Bradnams Commercial.
92
glazed walls – multi tier
Whereopeningsrequiremulti tiersorlevelsofglasspanels,selfsupportingstructuralglasswallsaremandatory.Therearethreetypesofstructuralglassglazingmethods,suspended,stackedandstructuralstand-offsystems.Designedforglazinglargeopeningsinbuildings,thesesystemsprovidemaximumvisibilityanddaylighting.Traditionalaluminiummullionsortransomsarereplacedbythicktoughenedglassfinsorsteeltensiontrusses.Thesefinsandtrussesaredesignedtoresistwindload.
suspended glass walls
Theglasspanelsarehungfromthebuildingstructurelikeacurtain.Thetoptierpanelsareconnectedtothestructurebyadjustablehangarbracketsandsubsequentlowerpanelsareconnectedbymetalfittingssuchasspiders,attheircorners.Thefaçadeislocatedintochannelsattheperimeterandallglassjointsandchannelsaresealedwithsiliconesealant.Thesupportstructure,toptierglassandhangarbracketsmustbeabletosustaintheverticalweightoftheglassbelowaswellaswindloading.
Theadjustablesuspensionsysteminconjunctionwithperimeterchannelspermitsthesystemtomoveindependentlyofthebuildingstructure.Thiscompensatesforconstructiondimensionalvariationsandovercomesproblemsassociatedwithbuildingmovement,vibrationandseismicloads.
Thehangingassemblyisnormallystabilisedagainstwindloadbyglassfinslocatedandfixedtothesupportstructurewithfittingsatthecornerjoints.Itisalsopossibletofixtheglasspanelstometalmullions,trusses,spaceframesorothersupportstructuresforlateralsupport.Dependingonengineeringspecificationsglasswallsashighas20metrescanbeinstalled.
stacked glass
Theoppositeofsuspendedsystems,stackedsystemsallowmultipletierstobestackedontopofeachother.Theglassdeadloadisimposedonthebottomtierpanelsandtothefloor.Theglasspanelsarelocatedintochannelsattheperimeterandalltheglassjointsaresealedwithsiliconesealant.Likesuspendedsystems,theglassfaçadeisstabilisedagainstwindloadbyfinsorotherstructures.Theglasspanelsareconnectedbyspecialmetalfittingstotheglassfins.Dependingonengineeringspecificationsamaximumglazedheightof8metresandnomorethan2tiersarerecommended.
Multi-tier suspended glass façade system using 10mm green toughened glass.
Photo left: Multi tier structural stand-off system glass façade using 30.56mm thick Cyclone resistant multi-laminated glass connected to bolt through stainless steel point fixings, fixed to stainless steel full height supports behind glass. Glass used is 30.56mm Cyclone resistant laminated. Make-up 10mm Azuria toughened / 2.28mm SGP / 10mm clear toughened / 2.28mm SGP / 6mm Energy Advantage low-E (#4) toughened – Fletcher Construction American Samoa. Glazed by National Glass. Architect – Lively Architects.
93
structural stand-off systems
Stainlesssteelstand-offsorspidersarefixedtobuildingsupportstructuressuchasconcretecolumns,steelmullionsandpostsormetal/cabletrusssystems.Thismethodallowstheglasstobecantileveredoffthesupportstructure.Thesystemcanallowforanunlimitedheightinglazingprovidedthatthereareintermediarystructuralsupportsatgivenspans.
structural fittings – spiders
Usedinglasswallandcanopyopenings,spider point fixingsareprimarilydesignedtoconnectmultipletiersorpanelsofglass.Spiderfixingsarealsousedinhighwindloadareaswhereconventionalsiliconeandglassfinsupportarenotsufficienttocopewithloadings.Madefromquality316stainlesssteel.
NG1-2 four way spider fixing.
Multi tier structural stand-off system glass façade using NG1-2 four way spider fixing bolted off stainless steel fins – 12mm grey toughened glass – Jon Kendall & Associates.
NG1-1 two way spider fixing.
NG1-2 four way spider fixing.
94
structural balustrading
Structuralglassbalustradingsystemsareacontemporaryalternativetotimberoraluminiumframedsystems.Itisgenerallyafreestandingsystemwithfewerverticalorhorizontalsupports.
balustrades – 1000mm from FFL with handrail
Allbalustradesprotectingadifferenceinlevelsequaltogreaterthan1000mmshallhaveastructuralinterlinkinghandrailsothatintheeventofglassbreakage,thehandrailwillsustaintherequiredloadingsasperAS1288andAS1170.
general specifications
Likeallaspectsofglassinbuildings,framelessglassbalustrading/poolfencesandgatesaresubjecttostrictstandardsandregulationsmanyofwhichhavetobecrosscheckedforcompliance.
Some of these include:
0 BCA(BuildingCodeofAustralia)localauthorityrequirements;
0 AS1170:Wind load, dead and live load requirements;
0 AS1288:Glass in buildings;
0 AS1926:Fences for swimming pools;
0 AS2820:Gate units for private for swimming pools.
Check with our technical staff on choosing the correct glass.
grouted bottom cantilevered method
Requiresthebottomofthepaneltobefullyandrigidlyfixedforthefulllengthofthepanel,usuallyintoagroutedchannel.Glassshouldbeheatsoaktreated.
diagram 13.10
95
12mm acid etched toughened glass bottom grouted cantilevered – Complete Design Fabrication.
12mm clear toughened glass bottom grouted cantilevered – Tewantin Glass.
96
stub post fixing
Glasspanelsareboltedtogetherwithstainlesssteelstubpostswhicharefixedintoconcretethroughcoredrilledholesorsurfacemounted.
clamp fittings – 2 edge support
Glasspanelsaresupportedbystainlesssteelclampfixingstoverticalpostsoneachside.Noholesrequiredinglass.
See Diagram 13.11.
spider fixing – 2 edge support
Glasspanelsaresupportedbyboltthrough2waystainlesssteelspiderfittingstoverticalpostsoneachside.Provides2panellinkwithflushorproudglassconnectors.
channel glazed – 2 edge support
Glasspanelsaresupportedinachannelfixedtoverticalpostsoneachside.
hand rail stand-off brackets
Rangeof304/316gradestainlesssteelboltthroughbracketsformountingofhandrail.
diagram 13.11: clamp fittings – 2 edge support
Theglazingpanelsaresupportedbyclampfittingstoverticalpostsateachside.
Spider fixing – 2 edge supported – NT Handrails.
Close up detail of spider fixing.
Photo below: Typical stainless steel hand rail stand off brackets with stainless steel handrail. Glazed by
QLD Glass. Hand rail by Associated Aluminium Service.
NG1260-F 316 stainless steel clamp fitting – 10/12mm glass.
97
Channel glazed 2 edge support protecting a difference in level less than 1000mm with no handrail – Australia Glass.
Stub posts – 329 Stainless steel.
Stub posts – Surface mount.
Stub posts – Core drilled.
diagram 13.12: typical stainless steel point fixing (stand off)
diagram 13.13: point fix balustrade
98
point fixed
Thisstructuralbalustradesystemfixestheglasstoconcretehobs,walls,timberandmetalframingviaboltthroughstainlesssteelpointfixingsorstandoffs.Mostintendedglazingapplicationsrequirespecialistengineeringtodeterminethefollowing(see Diagram 13.13):
0 Glassthickness,type,widthofpanel(A);
0 Numberoffixings,diametersize,lengthofpointfixingorstandoffandlengthoffixingrod(B)(see also stand-off detail, Diagram 13.12);
0 Minimumdistancebetweenholes,holetoglassedgeandconcreteedge(C);
0 Typeofhob/structureconstructionandwidthtodetermineadequacyorstrengthofthehob/structuretotakeloadingimposedbythebalustrade(D).
Furthertotheabove,thebalustrademustcomplytominimumheightregulations(E)withnoabilitytousethebackinghoborfixingstructureasaclimbablemount(F).Gapbetweenglassmustbeinaccordancewithminimumregulations(G).
Allpointfixingsorstandoffsaremadefrom316MarineGradeStainlessSteel.
Allbalustradesprotectingadifferenceinlevelequaltogreaterthan1000mmshallhaveastructuralinterlinkinghandrailsothatintheeventofglassbreakage,thehandrailwillsustaintherequiredloadingsasperAS1288andAS1170.
99
Point fixed with stainless steel stand offs structural balustrade – NT Handrails.
100
pool gates
Whengatesarerequiredtobeincorporatedinapoolfenceorbalustrade,theuseofcornerfixedpatchfittingsasshownareavailable.Thesegatesareoperatedwithselfclosingfloorspringclosersforpoolgaterequirements.Astainlesssteeltoppivotbracketisdesignedforglasstoglassorpost/walltoglasssituations.Maximumrecommendedsizeforgatesis1200mm(h)x1000mm(w).Minimumrecommendedthicknessis12mmtoughenedsafetyglass.Asperframelessbalustrading,poolgatesaresubjecttostrictcodesandregulations.
diagram 13.14
Frameless 12mm clear toughened pool gate with top/bottom corner patches and floor spring – Complete Design Fabrication.
A
B
C
Point fixed balustrade with handrail – Bradnams Commercial.
squash courts
Glassbackwallsquashcourtpackagesareavailableofferingthemaximumviewforspectatorswhilstprovidingastructuralbackwallforthecourtallowingplaynottobeinterrupted.Thesecourtsaremadefrom12mmtoughenedsafetyglassandstructuralfinsallfixedtogetherwithcountersunkscrewsandbushestoleavetheplayingsurfaceflush.Asurfacemountdoorcloserisfixedtotheoutsideofthedoorallowingeasyaccessandadjustment.Theexternalfixingangleismadefromprefabricatedaluminiumcuttosizeandreadytoinstall.Thestandardsizeavailableis2134mm(height)x6401mm(width),whichisthecompetitionsize,butnon-standardsizescanbemadeonrequest.
G-tech partition system
Thisuniquesystemusingstainlesssteelboltthroughfixingsallowsfortheconstructionofframelessglassdesignswithouttheuseofframingorconventional‘U’typechannel(see middle and bottom photos).G-techpartitionisdesignedtosuit10/12mmtoughenedglasswitheitherproudorcountersunkflushglassfixingcomponents.
overhead glazing
Dependingonsituationandcoderequirements,annealedlaminated,H/Slaminated,toughenedlaminatedandmonolithictoughenedcanbeusedinoverheadglazing.
H/S laminated glass
Acharacteristicofheatstrengthenedlaminatedglasswhenbrokenisthattheglasswillbreakintolargerpieces.Thisisusefulforoverheadglazingwheretheglassisthenlesslikelytosagandfalloutoftheopening.However,inthesesituationstheframingsystemshouldallowforadequatecaptureorcovertoensurethatwhenbothlitesoftheH/Slaminatedarebroken,theglassdoesnotfallout.
point fixed overhead glazing
Acountersunkfittingshouldbeavoidedinthesesituationsasbrokenglassismorelikelytofalloutandaroundthecountersunkfitting.Aproudfixingisthepreferredmethodwithadequatesizedplateswhichwillhelpretaintheglassintheopening.H/SlaminatedorH/Stoughenedcombinationlaminatedglassarethepreferredglazingtypes.
diagram 13.15
101
G-tech glass “Cube” – Brisbane Boys Grammar School – Australia Glass.
Close up detail of G-tech wall to glass fixing.
Glass back wall squash courts – Emerald QLD.
102
frameless shower screens
Framelesstoughenedsafetyglasscanprovideanalternativetostandardaluminiumframedshowerscreens.NationalGlasscansupplyshowerdooroptionsasshown.
Minimumrecommendedthicknessshouldbe10mmtoughenedsafetyglass.
fixing methods
SubjecttoAS1288guidelines,therearetwomainmethodsofinstallingframelesstoughenedshowerscreens:
0 Therecommendedmethodistomechanicallyfixtheglasswithspecialboltthroughplatedbrassorstainlesssteelanglebrackets;
0 Asecondmethodistouseanaluminiumorplatedbrass“U”channelwhichisscrewfixedtothewallandfloorandtheglassisfixedintothechannelusingstructuralgradesilicone.
maximum shower door width/height
Width (mm)
Wallhungdoors 600–700
Glasshungdoors 550–650
Height (mm)
Wallhungdoors 1850–2100
Glasshungdoors 1850–2100
structural bracing header bars
Foranyglasstoglasshingeshowerpanelsandfreestandingfixedshowerpanels,structuralbracingwillberequiredtoreduceexcessivedeflectionoftheglass.
Options include:
0 6-10mmtoughenedglasspanel,100–150mmwide,runningthelengthfromsidelitetosideliteorwalltoreturnpanel,overthedoor;
0 metalheaderbarinthesamefinishashingesetc;
0 10mmtoughenedglassquadrant(as shown left)UVadhesiveorsiliconefixedtoglassandwall.
All photos: Bradnams Showerscreens.
103
diagram 13.16: frameless shower screen types
type A
type D
type H
type F
type B type C
type Jtype I
type G
type E
104
waterproofing requirements
AS3740-2004Waterproofing for wet areas within residential buildingssetsoutthepositionalrequirementsofglasspanelsforhobsandhoblessshowers.Showerpanelsshouldbeflushwiththeshowerareasideofthehob.Hoblessshowersrequirestheglasstobepositionedoveraprescribedwaterproofingfloorangle.PleaseconsultAS3740forfurtherinformation.
Itisfurtherrecommendedthatnofloorfixingsbeusedwherethereislikelypenetrationofthewaterproofingmembrane.Alternatively,astructuralsiliconesealantshouldbeusedcombinedwithwallfixingsandheaderbars.
Special noteshouldbemadewithregardstowalltilingrequirementsunderAS3740.Thisiswithparticularreferencetosubstitutionofglasssplashbacksorcladdingfortiling.
frameless shower fittings
shower door hinges
0 Selfcenteringhingesfordoorsupto36kg;
0 Allfixingsandmechanicalpartsproducedfromstainlesssteel.Bodypartsproducedfromqualitybrass.Finishesavailableinchrome,titaniumgoldandsatinchromeplate;
0 Tosuitglassthicknesses10mm.
bracket fittings
0 Solidbrasstosuit10mmglass;
0 Finishesavailableinchrome,titaniumgold,satinchromeplate.
handles and knobs
0 Pullhandlesandtowelbarssetsaremadefrom304Gradestainlesssteeltubing.Finishesincludesatinandpolishedstainlessandtitaniumplatedgoldfinish;
0 Knobsmadefromsolidbrassplatedinchrome,titaniumgoldandsatinchromefinishes.
glazing ‘U’ channel
0 Availableinpolishedsilveranodisedaluminium16mmx14mmx1.8mmwallthicknessat3000mmlengths;
header bars
0 Madefrom19mmdiameter304gradestainlesssteeltubing;
0 Availableinsatinstainless,polishedandtitaniumgoldfinishes.
diagram 13.17: seals and wipes
diagram 13.18: waterbars
0 Chrome,satinandgoldfinishes.
105
NG992-2 180º glass to glass chrome shower hinge. NG990-1 wall to glass gold shower hinge.
NG48-1L 90º wall to glass chrome bracket. NG48-1 floor to glass satin bracket.
NG3540 chrome door knob. NG3838 clear glass door knob.
NG01 150mm ‘D’ handle. NG12-1A wall to glass header bar.