Post on 21-Jan-2016
HTTP://PHYSICSACT.WORDPRESS.COM
Chapter 21 The Electric Field 1: Discrete Charge Distributions Conceptual Problems *1 Similarities:
Differences:
The force between charges and masses varies as 1/r2.
There are positive and negative charges but only positive masses.
The force is directly proportional to the product of the charges or masses.
Like charges repel; like masses attract.
The gravitational constant G is many orders of magnitude smaller than the Coulomb constant k.
2 Determine the Concept No. In order to charge a body by induction, it must have charges that are free to move about on the body. An insulator does not have such charges.
3 Determine the Concept During this sequence of events, negative charges are attracted from ground to the rectangular metal plate B. When S is opened, these charges are trapped on B and remain there when the charged body is removed. Hence B is negatively charged and correct. is )(c
4 (a) Connect the metal sphere to ground; bring the insulating rod near the metal sphere and disconnect the sphere from ground; then remove the insulating rod. The sphere will be negatively charged. (b) Bring the insulating rod in contact with the metal sphere; some of the positive charge on the rod will be transferred to the metal sphere. (c) Yes. First charge one metal sphere negatively by induction as in (a). Then use that negatively charged sphere to charge the second metal sphere positively by induction.
1
Chapter 21
2
*5 Determine the Concept Because the spheres are conductors, there are free electrons on them that will reposition themselves when the positively charged rod is brought nearby.
(a) On the sphere near the positively charged rod, the induced charge is negative and near the rod. On the other sphere, the net charge is positive and on the side far from the rod. This is shown in the diagram.
(b) When the spheres are separated and far apart and the rod has been removed, the induced charges are distributed uniformly over each sphere. The charge distributions are shown in the diagram.
6 Determine the Concept The forces acting on +q are shown in the diagram. The force acting on +q due to Q is along the line joining them and directed toward Q. The force acting on +q due to +Q is along the line joining them and directed away from +Q.
Because charges +Q and Q are equal in magnitude, the forces due to these charges are equal and their sum (the net force on +q) will be to the right and so correct. is )(e Note that the vertical components of these forces add up to zero.
*7 Determine the Concept The acceleration of the positive charge is given by
.0 EFarrr
mq
m== Because q0 and m are both positive, the acceleration is in the same
direction as the electric field. correct. is )(d
*8 Determine the Concept E
ris zero wherever the net force acting on a test charge is
zero. At the center of the square the two positive charges alone would produce a net electric field of zero, and the two negative charges alone would also produce a net electric field of zero. Thus, the net force acting on a test charge at the midpoint of the
The Electric Field 1: Discrete Charge Distributions
3
square will be zero. correct. is )(b
9 (a) The zero net force acting on Q could be the consequence of equal collinear charges being equidistant from and on opposite sides of Q. (b) The charges described in (a) could be either positive or negative and the net force on Q would still be zero. (c) Suppose Q is positive. Imagine a negative charge situated to its right and a larger positive charge on the same line and the right of the negative charge. Such an arrangement of charges, with the distances properly chosen, would result in a net force of zero acting on Q. (d) Because none of the above are correct, correct. is )(d
10 Determine the Concept We can use the rules for drawing electric field lines to draw the electric field lines for this system. In the sketch to the right weve assigned 2 field lines to each charge q.
*11 Determine the Concept We can use the rules for drawing electric field lines to draw the electric field lines for this system. In the field-line sketch to the right weve assigned 2 field lines to each charge q.
Chapter 21
4
*12 Determine the Concept We can use the rules for drawing electric field lines to draw the electric field lines for this system. In the field-line sketch to the right weve assigned 7 field lines to each charge q.
13 Determine the Concept A positive charge will induce a charge of the opposite sign on the near surface of the nearby neutral conductor. The positive charge and the induced charge on the neutral conductor, being of opposite sign, will always attract one another.
correct. is )(a
*14 Determine the Concept Electric field lines around an electric dipole originate at the positive charge and terminate at the negative charge. Only the lines shown in (d) satisfy this requirement. correct. is )(d
*15 Determine the Concept Because 0, a dipole in a uniform electric field will experience a restoring torque whose magnitude is sinxpE . Hence it will oscillate about its equilibrium orientation, = 0. If
The Electric Field 1: Discrete Charge Distributions
5
(e) True 17 Determine the Concept The diagram shows the metal balls before they are placed in the water. In this situation, the net electric field at the location of the sphere on the left is due only to the charge q on the sphere on the right. If the metal balls are placed in water, the water molecules around each ball tend to align themselves with the electric field. This is shown for the ball on the right with charge q.
(a) The net electric field r E net that produces a force on the ball on the left is the
field r E due to the charge q on the ball on the right plus the field due to the layer
of positive charge that surrounds the ball on the right. This layer of positive charge is due to the aligning of the water molecules in the electric field, and the amount of positive charge in the layer surrounding the ball on the left will be less than +q. Thus, Enet < E. Because Enet < E, the force on the ball on the left is less than it would be if the balls had not been placed in water. Hence, the force will
decrease when the balls are placed in the water. (b) When a third uncharged metal ball is placed between the first two, the net electric field at the location of the sphere on the right is the field due to the charge +q on the sphere on the left, plus the field due to the charge Q and +Q on the sphere in the middle. This electric field is directed to the right.
The field due to the charge Q and +Q on the sphere in the middle at the location of the sphere on the right is to the right. It follows that the net electric field due to the charge +q on the sphere on the left, plus the field due to the charge Q and +Q on the sphere in the middle is to the right and has a greater magnitude than the field due only to the charge +q on the sphere on the left. Hence, the force on either sphere will increase if a third uncharged metal ball is placed between them. Remarks: The reduction of an electric field by the alignment of dipole moments with the field is discussed in further detail in Chapter 24.
Chapter 21
6
*18 Determine the Concept Yes. A positively charged ball will induce a dipole on the metal ball, and if the two are in close proximity, the net force can be attractive. *19 Determine the Concept Assume that the wand has a negative charge. When the charged wand is brought near the tinfoil, the side nearer the wand becomes positively charged by induction, and so it swings toward the wand. When it touches the wand, some of the negative charge is transferred to the foil, which, as a result, acquires a net negative charge and is now repelled by the wand. Estimation and Approximation 20 Picture the Problem Because it is both very small and repulsive, we can ignore the gravitational force between the spheres. It is also true that we are given no information about the masses of these spheres. We can find the largest possible value of Q by equating the electrostatic force between the charged spheres and the maximum force the cable can withstand. Using Coulombs law, express the electrostatic force between the two charged spheres:
2
2
lkQF =
Express the tensile strength Stensile of steel in terms of the maximum force Fmax in the cable and the cross-sectional area of the cable and solve for F:
AFS maxtensile = tensilemax ASF =
Equate these forces to obtain: tensile2
2
ASkQ =l
Solve for Q:
kASQ tensilel=
Substitute numerical values and evaluate Q:
( ) ( )( ) mC95.2C/mN1099.8N/m102.5m105.1m1 229
2824
==
Q
21 Picture the Problem We can use Coulombs law to express the net force acting on the copper cube in terms of the unbalanced charge resulting from the assumed migration of half the charges to opposite sides of the cube. We can, in turn, find the unbalanced charge Qunbalanced from the number of copper atoms N and the number of electrons per atom.
The Electric Field 1: Discrete Charge Distributions
7
(a) Using Coulombs law, express the net force acting on the copper rod due to the imbalance in the positive and negative charges:
2
2unbalanced
rkQF = (1)
Relate the number of copper atoms N to the mass m of the rod, the molar mass M of copper, and Avogadros number NA:
MV
Mm
NN rodCu
A
==
Solve for N to obtain: A
rodCu NMVN =
Substitute numerical values and evaluate N: ( )( ) ( )( )
atoms10461.8kg/mol1054.63
atoms/mol1002.6m104m105.0kg/m1093.8
22
3
2322233
=
=
N
Because each atom has 29 electrons and protons, we can express Qunbalanced as:
( )( )eNQ 721unbalanced 1029 = Substitute numerical values and evaluate Qunbalanced: ( )( )( )( ) C10963.110461.8C106.11029 22219721unbalanced ==Q
Substitute for Qunbalanced in equation (1) to obtain: ( )( )
( ) N1046.3m01.0C10963.1C/mN1099.8 10
2
22229
==
F
(b) Using Coulombs law, express the maximum force of repulsion Fmax in terms of the maximum possible charge Qmax:
2
2max
max rkQF =
Solve for Qmax:
kFrQ max
2
max =
Express Fmax in terms of the tensile strength Stensile of copper:
ASF tensilemax = where A is the cross sectional area of the cube.
Chapter 21
8
Substitute to obtain:
kASrQ tensile
2
max =
Substitute numerical values and evaluate Qmax:
( ) ( )( ) C1060.1C/mN1099.8
m10N/m103.2m01.0 5229
24282
max
=
=Q
Because : maxunbalanced 2QQ = ( )C0.32
C1060.12 5unbalanced== Q
Remarks: A net charge of 32 C means an excess of 2.001014 electrons, so the net imbalance as a percentage of the total number of charges is 4.061011 = 4109 %. 22 Picture the Problem We can use the definition of electric field to express E in terms of the work done on the ionizing electrons and the distance they travel between collisions. We can use the ideal-gas law to relate the number density of molecules in the gas and the scattering cross-section to the mean free path and, hence, to the electric field. (a) Apply conservation of energy to relate the work done on the electrons by the electric field to the change in their kinetic energy:
sFKW ==
From the definition of electric field we have:
qEF =
Substitute for F and s to obtain: qEW = , where the mean free path is the distance traveled by the electrons between ionizing collisions with nitrogen atoms.
Referring to pages 545-546 for a discussion on the mean-free path, use its definition to relate to the scattering cross-section and the number density for air molecules n:
n1=
Substitute for and solve for E to obtain: q
nWE =
Use the ideal-gas law to obtain: kT
PVNn ==
The Electric Field 1: Discrete Charge Distributions
9
Substitute for n to obtain: qkT
PWE = (1)
Substitute numerical values and evaluate E: ( )( )( )( )( )( )( ) N/C1041.2K300J/K1038.1C106.1 J/eV106.1eV1N/m10m10 62319
1925219
==
E
(b) From equation (1) we see that: PE and 1 TE
i.e., E increases linearly with pressure and varies inversely with temperature.
*23 Picture the Problem We can use Coulombs law to express the charge on the rod in terms of the force exerted on it by the soda can and its distance from the can. We can apply Newtons 2nd law in rotational form to the can to relate its acceleration to the electric force exerted on it by the rod. Combining these equations will yield an expression for Q as a function of the mass of the can, its distance from the rod, and its acceleration. Use Coulombs law to relate the force on the rod to its charge Q and distance r from the soda can:
2
2
rkQF =
Solve for Q to obtain:
kFrQ
2
= (1)
Apply to the can:
I= mass ofcenter
IFR =
Because the can rolls without slipping, we know that its linear acceleration a and angular acceleration are related according to:
Ra=
where R is the radius of the soda can.
Because the empty can is a hollow cylinder:
2MRI = where M is the mass of the can.
Substitute for I and and solve for F to obtain:
MaR
aMRF == 22
Substitute for F in equation (1):
kMarQ
2
=
Chapter 21
10
Substitute numerical values and evaluate Q: ( ) ( )( )
nC141
C/mN1099.8m/s1kg018.0m1.0
229
22
==Q
24 Picture the Problem Because the nucleus is in equilibrium, the binding force must be equal to the electrostatic force of repulsion between the protons. Apply 0=Fr to a proton:
0ticelectrostabinding = FF
Solve for Fbinding: ticelectrostabinding FF =
Using Coulombs law, substitute for Felectrostatic:
2
2
binding rkqF =
Substitute numerical values and evaluate Felectrostatic: ( )( )( ) N230m10 C106.1C/mN1099.8 215
219229
binding ==
F
Electric Charge 25 Picture the Problem The charge acquired by the plastic rod is an integral number of electronic charges, i.e., q = ne(e).
Relate the charge acquired by the plastic rod to the number of electrons transferred from the wool shirt:
( )enq = e
Solve for and evaluate ne: 1219e 1000.5C101.6C8.0 =
==
eqn
26 Picture the Problem One faraday = NAe. We can use this definition to find the number of coulombs in a faraday.
Use the definition of a faraday to calculate the number of coulombs in a faraday: ( )( ) C1063.9C/electron106.1electrons1002.6faraday1 41923A === eN
The Electric Field 1: Discrete Charge Distributions
11
*27 Picture the Problem We can find the number of coulombs of positive charge there are in 1 kg of carbon from , where nenQ C6= C is the number of atoms in 1 kg of carbon and the factor of 6 is present to account for the presence of 6 protons in each atom. We can find the number of atoms in 1kg of carbon by setting up a proportion relating Avogadros number, the mass of carbon, and the molecular mass of carbon to nC.
Express the positive charge in terms of the electronic charge, the number of protons per atom, and the number of atoms in 1 kg of carbon:
enQ C6=
Using a proportion, relate the number of atoms in 1 kg of carbon nC, to Avogadros number and the molecular mass M of carbon:
Mm
Nn C
A
C = M
mNn CAC =
Substitute to obtain: M
emNQ CA6=
Substitute numerical values and evaluate Q: ( )( )( ) C1082.4
kg/mol012.0C101.6kg1atoms/mol106.026 71923 ==
Q
Coulombs Law 28 Picture the Problem We can find the forces the two charges exert on each by applying Coulombs law and Newtons 3rd law. Note that because the vector pointing from
q
ir 2,1 =1 to q2 is in the positive x direction.
(a) Use Coulombs law to express the force that q1 exerts on q2:
2,122,1
212,1 rF r
qkq=r
Substitute numerical values and evaluate 2,1Fr
:
( )( )( )( ) ( )iiF mN0.24m3
C6C4/CmN108.992
229
2,1 ==r
Chapter 21
12
(b) Because these are action-and-reaction forces, we can apply Newtons 3rd law to obtain:
( )iFF mN0.242,11,2 == rr
(c) If q2 is 6.0 C: ( )( )( )
( ) ( )iiF mN0.24m3C6C4/CmN108.99
2
229
2,1 ==r
and
( )iFF mN0.242,11,2 == rr
29 Picture the Problem q2 exerts an attractive force 1,2F
r on q1 and q3 a repulsive force 1,3F
r.
We can find the net force on q1 by adding these forces.
Express the net force acting on q1:
1,31,21 FFFrrr +=
Express the force that q2 exerts on q1:
iF 21,2
211,2 r
qqk=r
Express the force that q3 exerts on q1:
( )iF 21,3
311,3 = r
qqkr
Substitute and simplify to obtain:
i
iiF
21,3
321,2
21
21,3
3121,2
211
=
=
rq
rq
qk
rqqk
rqqkr
Substitute numerical values and evaluate 1F
r:
( )( ) ( ) ( ) ( )iiF N1050.1m6 C6m3 C4C6/CmN1099.8 2222291 =
= r
The Electric Field 1: Discrete Charge Distributions
13
30 Picture the Problem The configuration of the charges and the forces on the fourth charge are shown in the figure as is a coordinate system. From the figure it is evident that the net force on q4 is along the diagonal of the square and directed away from q3. We can apply Coulombs law to express 4,1F
r, 4,2F
rand 4,3F
r and then add
them to find the net force on q4.
Express the net force acting on q4:
4,34,24,14 FFFFrrrr ++=
Express the force that q1 exerts on q4:
jF 24,1
414,1 r
qkq=r
Substitute numerical values and evaluate 4,1Fr
:
( )( ) ( ) ( )jjF N1024.3m05.0 nC3nC3/CmN1099.8 522294,1 =
=r
Express the force that q2 exerts on q4:
iF 24,2
424,2 r
qkq=r
Substitute numerical values and evaluate 4,2Fr
:
( )( ) ( ) ( )iiF N1024.3m05.0 nC3nC3/CmN1099.8 522294,2 =
=r
Express the force that q3 exerts on q4: 4,324,3
434,3 rF r
qkq=r , where is a unit vector pointing from q
4,3r
3 to q4.
Express 4,3rr
in terms of 1,3rr
and 4,1rr
:
( ) ( jirrr
m05.0m05.04,11,34,3
+= )+= rrr
Chapter 21
14
Convert to : 4,3rr
4,3r
( ) ( )( ) ( )
ji
jirr
r
707.0707.0
m05.0m05.0
m05.0m05.022
4,3
4,34,3
+=++== r
r
Substitute numerical values and evaluate 4,3F
r:
( )( ) ( ) ( )( ) ( )ji
jiF
N1014.1N1014.1
707.0707.0m205.0
nC3nC3/CmN1099.8
55
2229
4,3
=
+
=r
Substitute and simplify to find 4F
r:
( ) ( ) ( ) ( )( ) ( )ji
jiijFN1010.2N1010.2
N1014.1N1014.1N1024.3N1024.355
55554
+=+=r
31 Picture the Problem The configuration of the charges and the forces on q3 are shown in the figure as is a coordinate system. From the geometry of the charge distribution it is evident that the net force on the 2 C charge is in the negative y direction. We can apply Coulombs law to express 3,1F
rand 3,2F
r and then add them to find the net force on q3.
The net force acting on q3 is given by: 3,23,13 FFF
rrr +=
The Electric Field 1: Discrete Charge Distributions
15
Express the force that q1 exerts on q3:
jiF sincos3,1 FF =r
where
( )( )(
( ) ( ))
N3.12m0.08m0.03
C2C5C/mN1099.822
229
231
=+
=
=
rqkqF
and
=
= 6.20
cm8cm3tan 1
Express the force that q2 exerts on q3:
jiF sincos3,2 FF =r
Substitute for 3,1Fr
and 3,2Fr
and
simplify to obtain:
j
j
ijiF
sin2
sin
cossincos3
F
F
FFF
=
=r
Substitute numerical values and evaluate 3F
r:
( )( ) j
jFN66.8
6.20sinN3.1223
==r
*32 Picture the Problem The positions of the charges are shown in the diagram. It is apparent that the electron must be located along the line joining the two charges. Moreover, because it is negatively charged, it must be closer to the 2.5 C than to the 6.0 C charge, as is indicated in the figure. We can find the x and y coordinates of the electrons position by equating the two electrostatic forces acting on it and solving for its distance from the origin.
We can use similar triangles to express this radial distance in terms of the x and y coordinates of the electron.
Express the condition that must be ee FF ,2,1 =
Chapter 21
16
satisfied if the electron is to be in equilibrium: Express the magnitude of the force that q1 exerts on the electron:
( )21,1 m25.1+= r ekqF e Express the magnitude of the force that q2 exerts on the electron:
22
,2 reqk
F e =
Substitute and simplify to obtain: ( ) 2221 m25.1 rqr q =+
Substitute for q1 and q2 and simplify:
( ) ( )0m25.1
m2361.2m4.1 122
=++ rr
Solve for r to obtain:
m0.4386and
m036.2
=
=
r
r
Because r < 0 is unphysical, well consider only the positive root.
Use the similar triangles in the diagram to establish the proportion involving the y coordinate of the electron:
m1.12m2.036
m5.0=ey
Solve for ye: m909.0=ey
Use the similar triangles in the diagram to establish the proportion involving the x coordinate of the electron:
m1.12m2.036
m1=ex
Solve for xe: m82.1=ex
The coordinates of the electrons position are:
( ) ( )m0.909m,1.82, =ee yx
The Electric Field 1: Discrete Charge Distributions
17
*33 Picture the Problem Let q1 represent the charge at the origin, q2 the charge at (0, 0.1 m), and q3 the charge at (0.2 m, 0). The diagram shows the forces acting on each of the charges. Note the action-and-reaction pairs. We can apply Coulombs law and the principle of superposition of forces to find the net force acting on each of the charges.
Express the net force acting on q1: 1,31,21 FFF
rrr +=
Express the force that q2 exerts on q1: 1,23
1,2
12
1,2
1,221,2
121,22
1,2
121,2 r
rrF r
rrr
qkqrr
qkqr
qkq ===
Substitute numerical values and evaluate 1,2Fr
:
( )( ) ( )( ) ( ) ( jjF N80.1m1.0m1.0 C1C2/CmN1099.8 32291,2 = )= r
Express the force that q3 exerts on q1: 1,331,3
131,3 rF
rrr
qkq=
Substitute numerical values and evaluate 1,3Fr
:
( )( ) ( )( ) ( ) ( iiF N899.0m2.0m2.0 C1C4/CmN1099.8 32291,3 = )= r
Substitute to find : 1F
r ( ) ( ) jiF N80.1N899.01 +=r
Express the net force acting on q2:
( ) jFFF
FFF
N80.12,3
1,22,3
2,12,32
==+=
rrrrrr
because 2,1Fr
and 1,2Fr
are action-and-reaction
forces.
Chapter 21
18
Express the force that q3 exerts on q2:
( ) ([ ]jirF
m1.0m2.032,3
23
2,332,3
232,3
+=
=
rqkq
rqkq r
)
r
Substitute numerical values and evaluate 2,3F
r:
( )( ) ( )( ) ( ) ( )[ ]( ) ( ) ji
jiF
N640.0N28.1
m1.0m2.0m224.0
C2C4/CmN1099.8 3229
2,3
+=
+= r
Find the net force acting on q2:
( ) ( ) ( ) ( )( ) ( ) ji
jjijFF
N16.1N28.1
N80.1N640.0N28.1N80.12,32
=+== rr
Noting that 3,1F
rand 1,3F
rare an action-and-reaction pair, as are 3,2F
rand 2,3F
r,
express the net force acting on q3:
( ) ( ) ( )[ ]( ) ( ) ji
jiiFFFFF
N640.0N381.0
N640.0N28.1N899.02,31,33,23,13
=+==+= rrrrr
34 Picture the Problem Let q1 represent the charge at the origin and q3 the charge initially at (8 cm, 0) and later at (17.75 cm, 0). The diagram shows the forces acting on q3 at (8 cm, 0). We can apply Coulombs law and the principle of superposition of forces to find the net force acting on each of the charges.
Express the net force on q2 when it is at (8 cm, 0):
( )
+=
+=+=
3,233,2
23,13
3,1
13
3,233,2
323,13
3,1
31
3,23,12 0,cm8
rr
rr
FFF
rr
rr
rrr
rQ
rqkq
rqkQ
rqkq
The Electric Field 1: Discrete Charge Distributions
19
Substitute numerical values to obtain: ( )
( )( ) ( ) ( ) ( ) ( ) +
=
ii
i
m04.0m04.0
m08.0m0.08C5C2/CmN1099.8
N7.19
32
3229 Q
Solve for and evaluate Q2: C00.32 =Q
Remarks: An alternative solution is to equate the electrostatic forces acting on q2 when it is at (17.75 cm, 0). 35 Picture the Problem By considering the symmetry of the array of charges we can see that the y component of the force on q is zero. We can apply Coulombs law and the principle of superposition of forces to find the net force acting on q.
Express the net force acting on q: qQqxQq ,45ataxis,on 2 += FFF
rrr
Express the force on q due to the charge Q on the x axis:
iF 2axis,on RkqQ
qxQ =r
Express the net force on q due to the charges at 45: i
iF
2
2
45cos22
2
2,45at
RkqQ
RkqQ
=
=r
Substitute to obtain:
i
iiF
221
2
2
2
22
+=
+=
RkqQ
RkqQ
RkqQ
q
r
36 Picture the P oblem Let the Hr + ions be in the x-y plane with H1 at (0, 0, 0), H2 at (a, 0, 0), and H3 at ( )0,23,2 aa . The N3 ion, q4 in our notation, is then at ( )32,32,2 aaa where a =1.641010 m. To simplify our calculations well set
N1056.8 922 == Cake . We can apply Coulombs law and the principle of superposition of forces to find the net force acting on each ion.
Chapter 21
20
Express the net force acting on q1:
1,41,31,21 FFFFrrrr ++=
Find 1,2Fr
:
( ) iirF 1,22
1,2
211,2 CCr
qkq ===r
Find 1,3Fr
:
+=
+
=
=
ji
ji
rF
23
21
2
302
0
1,321,3
131,3
C
a
aa
C
rqkqr
Noting that the magnitude of q4 is three times that of the other charges and that it is negative, express 1,4F
r:
+
+
=
+
+
=
+
+
+
+
==
kjikji
kjirF
32
321
213
32
32
23
32
322
320
320
20
33222
1,41,4
Ca
aaa
C
aaa
aaa
CCr
The Electric Field 1: Discrete Charge Distributions
21
Substitute to find : 1Fr
k
kji
jiiF
6
32
321
213
23
21
1
C
C
CC
=
+
+
+
+=r
From symmetry considerations:
kFFF 6132 C===rrr
Express the condition that molecule is in equilibrium:
04321 =+++ FFFFrrrr
Solve for and evaluate : 4Fr ( )
k
FFFFF63
3 13214
C==++= rrrrr
The Electric Field *37 Picture the Problem Let q represent the charge at the origin and use Coulombs law for Er
due to a point charge to find the electric field at x = 6 m and 10 m.
(a) Express the electric field at a point P located a distance x from a charge q:
( ) P,02 rE xkqx =r
Evaluate this expression for x = 6 m:
( ) ( )( )( )( )i
iE
N/C999
m6
C4/CmN1099.8m6 2229
=
= r
(b) Evaluate E
rat x = 10 m:
( ) ( )( )( ) ( ) ( )iiE N/C360m10 C4/CmN1099.8m10 2229
== r
(c) The following graph was plotted using a spreadsheet program:
Chapter 21
22
-500
-250
0
250
500
-2 -1 0 1 2
x (m)
E x (N
/C)
*38 Picture the Problem Let q represent the charges of +4 C and use Coulombs law for Er
due to a point charge and the principle of superposition for fields to find the electric field at the locations specified.
Noting that q1 = q2, use Coulombs law and the principle of superposition to express the electric field due to the given charges at a point P a distance x from the origin:
( ) ( ) ( ) ( ) ( )( ) ( )
+=
+=+=+=
P,2P,22
P,2P,21P,22
P,21
21
212121
m8
11/CmkN36
m8
11m8
qqqqqq
xx
xxkq
xkq
xkqxxx
rr
rrrrEEErrr
(a) Apply this equation to the point at x = 2 m:
( ) ( ) ( ) ( ) ( ) ( ) ( )iiiE kN/C36.9m101m2 1/CmkN36m2 222 =+
=r
(b) Evaluate Er
at x = 2 m:
( ) ( ) ( ) ( ) ( ) ( ) ( )iiiE kN/C00.8m6 1m2 1/CmkN36m2 222 =+=r
The Electric Field 1: Discrete Charge Distributions
23
(c) Evaluate Er
at x = 6 m:
( ) ( ) ( ) ( ) ( ) ( ) ( )iiiE kN/C00.8m2 1m6 1/CmkN36m6 222 =+=r
(d) Evaluate E
rat x = 10 m:
( ) ( ) ( ) ( ) ( ) ( ) ( )iiiE kN/C35.9m2 1m101/CmkN36m10 222 =+=r
(e) From symmetry considerations: ( ) 0m4 =E
(f) The following graph was plotted using a spreadsheet program:
-100
-50
0
50
100
-4 0 4 8
x (m)
E x (
kN m
2 /C)
12
39 Picture the Problem We can find the electric field at the origin from its definition and the force on a charge placed there from EF
rrq= . We can apply Coulombs law to find
the value of the charge placed at y = 3 cm. (a) Apply the definition of electric field to obtain:
( ) ( ) jjFE kN/C400nC2
N108 4
0
===
q
rr
(b) Express and evaluate the force on a charged body in an electric field:
( )( )( ) j
jEFmN60.1
kN/C400nC4
=== rr q
Chapter 21
24
(c) Apply Coulombs law to obtain:
( )( ) ( ) ( ) jj mN60.1m0.03 nC4 2 =kq
Solve for and evaluate q: ( )( )( )( )
nC40.0
nC4/CmN1099.8m0.03mN60.1229
2
==q
40 Picture the Problem We can compare the electric and gravitational forces acting on an electron by expressing their ratio. We can equate these forces to find the charge that would have to be placed on a penny in order to balance the earths gravitational force on it.
(a) Express the magnitude of the electric force acting on the electron:
eEFe =
Express the magnitude of the gravitational force acting on the electron:
gmF eg =
Express the ratio of these forces to obtain:
mgeE
FF
g
e =
Substitute numerical values and evaluate Fe/Fg:
( )( )( )( )12
231
19
1069.2
m/s9.81kg109.11N/C150C101.6
==
g
e
FF
or ( ) ge FF 121069.2 = , i.e., the electric force is greater by a factor of 2.691012.
(b) Equate the electric and gravitational forces acting on the penny and solve for q to obtain:
Emgq =
Substitute numerical values and evaluate q:
( )( )C1096.1
N/C150m/s9.81kg103
4
23
=
=q
The Electric Field 1: Discrete Charge Distributions
25
41 Picture the Problem The diagram shows the locations of the charges q1 and q2 and the point on the x axis at which we are to find .E
r From symmetry considerations we
can conclude that the y component of Er
at any point on the x axis is zero. We can use Coulombs law for the electric field due to point charges to find the field at any point on the x axis and to find the force on a charge q
EFrr
q=0 placed on the x axis at
x = 4 cm.
(a) Letting q = q1 = q2, express the x-component of the electric field due to one charge as a function of the distance r from either charge to the point of interest:
iE cos2 rkq
x =r
Express for both charges: xEr
iE cos2 2 rkq
x =r
Substitute for cos and r, substitute numerical values, and evaluate to obtain: ( ) ( )( )( )
( ) ( )[ ]( )i
iiiE
kN/C4.53
m0.04m0.03
m0.04nC6/CmN108.992m04.02m04.02 2322229
32
=+
===r
kqrr
kqx
r
(b) Apply to find the force on a charge q
EFrr
q=0 placed on the x axis at
x = 4 cm:
( )( )( )i
iFN0.69
kN/C4.53nC2
==r
*42 Picture the Problem If the electric field at x = 0 is zero, both its x and y components must be zero. The only way this condition can be satisfied with the point charges of +5.0 C and 8.0 C are on the x axis is if the point charge of +6.0 C is also on the x axis. Let the subscripts 5, 8, and 6 identify the point charges and their fields. We can use Coulombs law for E
rdue to a point charge and the principle of superposition for fields
to determine where the +6.0 C charge should be located so that the electric field at x = 0 is zero.
Chapter 21
26
Express the electric field at x = 0 in terms of the fields due to the charges of +5.0 C, 8.0 C, and +6.0 C:
( )0
0 C6C8C5=
++= EEEErrrr
Substitute for each of the fields to obtain:
0 828
862
6
652
5
5 =++ rrr
rkq
rkq
rkq
or ( ) ( ) 0 28
82
6
62
5
5 =++ iii
rkq
rkq
rkq
Divide out the unit vector to obtain:
i
028
82
6
62
5
5 =
rq
rq
rq
Substitute numerical values to obtain: ( ) ( ) 0cm4
86cm35
226
2 = r
Solve for r6: cm38.26 =r
43 Picture the Problem The diagram shows the electric field vectors at the point of interest P due to the two charges. We can use Coulombs law for E
rdue to point charges and the
superposition principle for electric fields to find PEr
. We can apply EFrr
q= to find the force on an electron at (1 m, 0).
(a) Express the electric field at (1 m, 0) due to the charges q1 and q2:
21P EEErrr +=
The Electric Field 1: Discrete Charge Distributions
27
Evaluate : 1Er
( )( )( ) ( )
( ) ( )( ) ( )
( )( )( ) ( ) ji
ji
jirE
kN/C575.0kN/C44.1
371.0928.0N/C1055.1
m2m5
m2m5m2m5
C5/CmN1099.8
3
2222
229
P1,2P1,
11
+=+=
++
+==
rkqr
Evaluate : 2E
r
( )( )( ) ( )
( ) ( )( ) ( )
( )( )( ) ( ) ji
ji
jirE
kN/C54.9kN/C54.9
707.0707.0N/C105.13
m2m2
m2m2m2m2
C12/CmN1099.8
3
2222
229
P2,2P2,
22
+==
++
+==
rkqr
Substitute for and and simplify to find 1E
r2E
rPE
r:
( ) ( ) ( ) ( )( ) ( ) ji
jijiEkN/C1.10kN/C10.8
kN/C54.9kN/C54.9kN/C575.0kN/C44.1P+=
+++=r
The magnitude of is: PE
r
( ) ( )
kN/C9.12
kN/C10.1kN/C8.10 22P=
+=E
The direction of is: PE
r
=
=
231
kN/C8.10kN/C10.1tan 1E
Note that the angle returned by your
calculator for
kN/C8.10kN/C10.1tan 1 is the
reference angle and must be increased by 180 to yield E.
(b) Express and evaluate the force on an electron at point P:
Chapter 21
28
( ) ( ) ( )[ ]( ) ( )ji
jiEFN10.621N10.301
kN/C1.10kN/C10.8C10602.11515
19P
+=+== rr q
Find the magnitude of F
r: ( ) ( )
N1008.2
N1062.1N1030.115
215215
=+=F
Find the direction of F
r: =
=
3.51
N101.3N101.62tan 15
151
F
44 Picture the Problem The diagram shows the locations of the charges q1 and q2 and the point on the x axis at which we are to find E
r. From symmetry considerations we can
conclude that the y component of Er
at any point on the x axis is zero. We can use Coulombs law for the electric field due to point charges to find the field at any point on the x axis. We can establish the results called for in parts (b) and (c) by factoring the radicand and using the approximation 11 + whenever
The Electric Field 1: Discrete Charge Distributions
29
and
( ) 23222 ax kqxEx +=
(b) For a,x > x2 + a2 x2, so:
( ) 2232 22 xkqxkqxEx =
(c) .2by given be wouldfield Its .2 magnitude of
charge single a be appear to wouldby separated charges the, For
2xkqEq
aax
x =>>
Factor the radicand to obtain: 23
2
22 12
+=
xaxkqxEx
For a
Chapter 21
30
(a) Express the electric field at (3 m, 1 m) due to the charges q1 and q2:
21P EEErrr +=
Evaluate : 1Er
( )( )( ) ( )
( ) ( )( ) ( )
( )( ) ( ) ( jijijirE
kN/C544.0kN/C908.0514.0857.0kN/C06.1
m3m5
m3m5m3m5
C4/CmN1099.82222
229
P1,21.P
11
+=+=
++
+==
rkqr
)
Evaluate 2E
r:
( )( )( ) ( )
( ) ( )( ) ( )
( )( ) ( ) ( jijijirE
kN/C01.1kN/C01.2447.0894.0kN/C25.2
m2m4
m2m4m2m4
C5/CmN1099.82222
229
P2,2P2,
22
+==
++
+==
rkqr
)
Substitute and simplify to find PE
r:
( ) ( ) ( ) ( )( ) ( ) ji
jijiEkN/C55.1kN/C10.1
kN/C01.1kN/C01.2kN/C544.0kN/C908.0P+=
+++=r
The magnitude of is: PE
r
( ) ( )
kN/C90.1
kN/C55.1kN/C10.1 22P=
+=E
The Electric Field 1: Discrete Charge Distributions
31
The direction of is: PEr
=
= 235
kN/C10.1kN/C55.1tan 1E
Note that the angle returned by your
calculator for
kN/C10.1kN/C55.1tan 1 is the
reference angle and must be increased by 180 to yield E.
(b) Express and evaluate the force on a proton at point P: ( ) ( ) ( )[ ]
( ) ( )jijiEF
N1048.2N10.761
kN/C55.1kN/C10.1C106.11616
19P
+=+== rr q
The magnitude of F
ris:
( ) ( ) N1004.3N1048.2N10.761 16216216 =+=F
The direction of Fr
is: =
=
235
N1076.1N1048.2tan 16
161
F where, as noted above, the angle returned by your calculator for
N1076.1N1048.2tan 16
161 is the reference
angle and must be increased by 180 to yield E.
46 Picture the Problem In Problem 44 it is shown that the electric field on the x axis, due to equal positive charges located at (0, a) and (0,a), is given by ( ) .2 2322 += axkqxEx We can identify the locations at which Ex has it greatest values by setting dEx/dx equal to zero.
(a) Evaluate dx
dEx :
Chapter 21
32
( )[ ] ( )[ ]( ) ( )( ) ( ) ( )
( )[ ( ) ]23222522223222522
23222322
23222322
32
2232
2
22
+++=
+++
=
+++=
+=+=
axaxxkq
axxaxxkq
axaxdxdxkq
axxdxdkqaxkqx
dxd
dxdEx
Set this derivative equal to zero:
( ) ( ) 03 232225222 =+++ axaxx
Solve for x to obtain: 2
ax =
(b) The following graph was plotted using a spreadsheet program:
2kq = 1 and a = 1
-0.4
-0.2
0.0
0.2
0.4
-10 -5 0 5 10
x
E x
47 Picture the Problem We can determine the stability of the equilibrium in Part (a) and Part (b) by considering the forces the equal charges q at y = +a and y = a exert on the test charge when it is given a small displacement along either the x or y axis. The application of Coulombs law in Part (c) will lead to the magnitude and sign of the charge that must be placed at the origin in order that a net force of zero is experienced by each of the three charges. (a) Because Ex is in the x direction, a positive test charge that is displaced from
The Electric Field 1: Discrete Charge Distributions
33
(0, 0) in either the +x direction or the x direction will experience a force pointing away from the origin and accelerate in the direction of the force.
axis. the alongnt displaceme small afor unstable is (0,0)at mequilibriu thely,Consequent
x If the positive test charge is displaced in the direction of increasing y (the positive y direction), the charge at y = +a will exert a greater force than the charge at y = a, and the net force is then in the y direction; i.e., it is a restoring force. Similarly, if the positive test charge is displaced in the direction of decreasing y (the negative y direction), the charge at y = a will exert a greater force than the charge at y = a, and the net force is then in the y direction; i.e., it is a restoring force.
axis. the alongnt displaceme small afor stable is (0,0)at mequilibriu thely,Consequent
y
(b)
axis. thealong ntsdisplacemefor unstable andaxis thealong ntsdisplacemefor (0,0)at stable is mequilibriu thecharge,
testnegative afor that,finds one ),(Part in as arguments same theFollowing
yx
a
(c) Express the net force acting on the charge at y = +a: ( ) 02 2
2
20
at =+= += akqakqqF ayq
Solve for q0 to obtain: 0410 qq =
Remarks: In Part (c), we could just as well have expressed the net force acting on the charge at y = a. Due to the symmetric distribution of the charges at y = a and y = +a, summing the forces acting on q0 at the origin does not lead to a relationship between q0 and q. *48 Picture the Problem In Problem 44 it is shown that the electric field on the x axis, due to equal positive charges located at (0, a) and (0,a), is given by ( ) .2 2322 += axkqxEx We can use k'mT 2= to express the period of the motion in terms of the restoring constant k. (a) Express the force acting on the on the bead when its displacement from the origin is x:
( ) 232222
axxkqqEF xx +==
Chapter 21
34
Factor a2 from the denominator to obtain:
23
2
22
2
1
2
+
=axa
xkqFx
For x
The Electric Field 1: Discrete Charge Distributions
35
field. electric theopposite iselectron an of
onaccelerati theofdirection The
(c) Using the definition of acceleration, relate the time required for an electron to reach 0.01c to its acceleration:
ac
avt 01.0==
Substitute numerical values and evaluate t:
( ) s170.0m/s101.76m/s1030.01
213
8
==t
(d) Find the distance the electron travels from its average speed and the elapsed time:
( )[ ]( )cm5.25
s170.0m/s10301.00 821av
=+=
=
tvx
*50 Picture the Problem We can use Newtons 2nd law of motion to find the acceleration of the proton in the uniform electric field and constant-acceleration equations to find the time required for it to reach a speed of 0.01c and the distance it travels while acquiring this speed. (a) Use data found at the back of your text to compute e/m for an electron: C/kg1058.9
kg1067.1C106.1
7
27
19
==
pme
Apply Newtons 2nd law to relate the acceleration of the electron to the electric field:
pp meE
mFa == net
Substitute numerical values and evaluate a:
( )( )29
72
19
m/s1058.9
kg1067.1N/C100C101.6
=
=
a
field. electric the ofdirection in the isproton a of
onaccelerati theofdirection The
Chapter 21
36
(b) Using the definition of acceleration, relate the time required for an electron to reach 0.01c to its acceleration:
ac
avt 01.0==
Substitute numerical values and evaluate t:
( ) s313m/s1058.9m/s1030.01
29
8
==t
51 Picture the Problem The electric force acting on the electron is opposite the direction of the electric field. We can apply Newtons 2nd law to find the electrons acceleration and use constant acceleration equations to find how long it takes the electron to travel a given distance and its deflection during this interval of time. (a) Use Newtons 2nd law to relate the acceleration of the electron first to the net force acting on it and then the electric field in which it finds itself:
ee me
mEFarr
r == net
Substitute numerical values and evaluate a : r ( )
( )jja
m/s1003.7
N/C400kg109.11C101.6
213
31
19
==
r
(b) Relate the time to travel a given distance in the x direction to the electrons speed in the x direction:
ns0.50m/s102
m0.16 ==
=xvxt
(c) Using a constant-acceleration equation, relate the displacement of the electron to its acceleration and the elapsed time:
( )( )( )( ) j
j
ay
cm79.8
ns50m/s1003.7 221321
221
==
= tyrr
i.e., the electron is deflected 8.79 cm downward.
52 Picture the Problem Because the electric field is uniform, the acceleration of the electron will be constant and we can apply Newtons 2nd law to find its acceleration and use a constant-acceleration equation to find its speed as it leaves the region in which there is a uniform electric field. Using a constant-acceleration xavv += 2202
The Electric Field 1: Discrete Charge Distributions
37
equation, relate the speed of the electron as it leaves the region of the electric field to its acceleration and distance of travel:
or, because v0 = 0, xav = 2
Apply Newtons 2nd law to express the acceleration of the electron in terms of the electric field:
ee meE
mFa == net
Substitute to obtain:
emxeEv = 2
Substitute numerical values and evaluate v: ( )( )( ) m/s1075.3
kg109.11m0.05N/C108C101.62 7
31
419
==
v
Remarks: Because this result is approximately 13% of the speed of light, it is only an approximation. 53 Picture the Problem We can apply the work-kinetic energy theorem to relate the change in the objects kinetic energy to the net force acting on it. We can express the net force acting on the charged body in terms of its charge and the electric field. Using the work-kinetic energy theorem, express the kinetic energy of the object in terms of the net force acting on it and its displacement:
xFKW == net
Relate the net force acting on the charged object to the electric field:
QEF =net
Substitute to obtain: xQEKKK == if or, because Ki = 0,
xQEK =f
Solve for Q: xE
KQ =f
Chapter 21
38
Substitute numerical values and evaluate Q: ( )( ) C800m0.50N/C300
J0.12 ==Q *54 Picture the Problem We can use constant-acceleration equations to express the x and y coordinates of the particle in terms of the parameter t and Newtons 2nd law to express the constant acceleration in terms of the electric field. Eliminating the parameter will yield an equation for y as a function of x, q, and m that we can solve for Ey. Express the x and y coordinates of the particle as functions of time:
( )tvx cos= and ( ) 221sin tatvy y=
Apply Newtons 2nd law to relate the acceleration of the particle to the net force acting on it:
mqE
mF
a yy == ynet,
Substitute in the y-coordinate equation to obtain:
( ) 22
sin tm
qEtvy y=
Eliminate the parameter t between the two equations to obtain:
( ) 222 cos2tan xmvqE
xy y =
Set y = 0 and solve for Ey: qx
mvEy2sin2=
Substitute the non-particle specific data to obtain:
( )( )
( )qm
qmEy
214
26
m/s1064.5
m015.070sinm/s103
=
=
(a) Substitute for the mass and charge of an electron and evaluate Ey:
( )kN/C3.21
C101.6kg109.11m/s105.64 19
31214
==
yE
(b) Substitute for the mass and charge of a proton and evaluate Ey:
( )MN/C89.5
C101.6kg1067.1m/s105.64 19
72214
==
yE
The Electric Field 1: Discrete Charge Distributions
39
55 Picture the Problem We can use constant-acceleration equations to express the x and y coordinates of the electron in terms of the parameter t and Newtons 2nd law to express the constant acceleration in terms of the electric field. Eliminating the parameter will yield an equation for y as a function of x, q, and m. We can decide whether the electron will strike the upper plate by finding the maximum value of its y coordinate. Should we find that it does not strike the upper plate, we can determine where it strikes the lower plate by setting y(x) = 0. Express the x and y coordinates of the electron as functions of time:
( )tvx cos0= and ( ) 2210 sin tatvy y=
Apply Newtons 2nd law to relate the acceleration of the electron to the net force acting on it:
e
y
e
yy m
eEm
Fa == net,
Substitute in the y-coordinate equation to obtain:
( ) 20 2sin tmeE
tvye
y=
Eliminate the parameter t between the two equations to obtain:
( ) ( ) 2220 cos2
tan xvmeE
xxye
y
= (1)
To find ymax, set dy/dx = 0 for extrema:
extremafor0cos
tan 220
== x'
vmeE
dxdy
e
y
Solve for x to obtain: y
e
eEvmx'2
2sin20 = (See remark below.)
Substitute x in y(x) and simplify to obtain ymax:
y
e
eEvmy2
sin220max
=
Substitute numerical values and evaluate ymax: ( )( )( )( ) cm02.1N/C103.5C101.62 54sinm/s105kg109.11 319
22631
max ==
y
and, because the plates are separated by 2 cm, the electron does not strike the upper plate.
Chapter 21
40
To determine where the electron will strike the lower plate, set y = 0 in equation (1) and solve for x to obtain:
y
e
eEvmx 2sin
20=
Substitute numerical values and evaluate x: ( )( )( )( ) cm07.4N/C105.3C106.1 90sinm/s105kg1011.9 319
2631
==
x
Remarks: x is an extremum, i.e., either a maximum or a minimum. To show that it is a maximum we need to show that d2y/dx2, evaluated at x, is negative. A simple alternative is to use your graphing calculator to show that the graph of y(x) is a maximum at x. Yet another alternative is to recognize that, because equation (1) is quadratic and the coefficient of x2 is negative, its graph is a parabola that opens downward. 56 Picture the Problem The trajectory of the electron while it is in the electric field is parabolic (its acceleration is downward and constant) and its trajectory, once it is out of the electric field is, if we ignore the small gravitational force acting on it, linear. We can use constant-acceleration equations and Newtons 2nd law to express the electrons x and y coordinates parametrically and then eliminate the parameter t to express y(x). We can find the angle with the horizontal at which the electron leaves the electric field from the x and y components of its velocity and its total vertical deflection by summing its deflections over the first 4 cm and the final 12 cm of its flight. (a) Using a constant-acceleration equation, express the x and y coordinates of the electron as functions of time:
( ) tvtx 0= and ( ) 221,0 tatvty yy +=
Because v0,y = 0:
( ) tvtx 0= (1) and ( ) 221 taty y=
Using Newtons 2nd law, relate the acceleration of the electron to the electric field:
e
y
ey m
eEmFa
== net
The Electric Field 1: Discrete Charge Distributions
41
Substitute to obtain:
( ) 22
tm
eEty
e
y= (2)
Eliminate the parameter t between equations (1) and (2) to obtain:
( ) 2220 42
xK
eEx
vmeE
xy ye
y ==
Substitute numerical values and evaluate y(4 cm):
( ) ( )( )( )( ) mm40.6J1024 m0.04N/C102C101.6m04.0 162419
==
y
(b) Express the horizontal and vertical components of the electrons speed as it leaves the electric field:
cos0vvx = and
sin0vvy = Divide the second of these equations by the first to obtain:
0
11 tantanvv
vv y
x
y ==
Using a constant-acceleration equation, express vy as a function of the electrons acceleration and its time in the electric field:
tavv yyy += ,0 or, because v0,y = 0
0
net,
vx
meE
tm
Ftav
e
y
e
yyy ===
Substitute to obtain:
=
=
KxeE
vmxeE y
e
y
2tantan 12
0
1
Substitute numerical values and evaluate : ( )( )( )( ) =
=
7.17
J1022m0.04N/C102C101.6tan 16
4191
(c) Express the total vertical displacement of the electron:
cm12cm4total yyy +=
Relate the horizontal and vertical distances traveled to the screen to the horizontal and vertical components of its velocity:
tvx x= and
tvy y=
Chapter 21
42
Eliminate t from these equations to obtain:
( )xxvv
yx
y tan==
Substitute numerical values and evaluate y:
( )[ ]( ) cm83.3m12.07.17tan ==y
Substitute for y4 cm and y12 cm and evaluate ytotal: cm47.4
cm83.3cm640.0total=
=y
i.e., the electron will strike the fluorescent screen 4.47 cm below the horizontal axis.
57 Picture the Problem We can use its definition to find the dipole moment of this pair of charges. (a) Apply the definition of electric dipole moment to obtain:
Lprr q=
and ( )( ) mC1000.8m4pC2 18 == p
(b) If we assume that the dipole is oriented as shown to the right, then
is to the right; pointing from the
negative charge toward the positive charge.
pr
*58 Picture the Problem The torque on an electric dipole in an electric field is given by
and the potential energy of the dipole by Eprrr = .Ep rr =U
Using its definition, express the torque on a dipole moment in a uniform electric field:
Eprrr =
and sinpE=
where is the angle between the electric dipole moment and the electric field.
(a) Evaluate for = 0: 00sin == pE
The Electric Field 1: Discrete Charge Distributions
43
(b) Evaluate for = 90: ( )( )mN1020.3
90sinN/C100.4nm5.024
4
==
e
(c) Evaluate for = 30: ( )( )
mN1060.1
30sinN/C100.4nm5.024
4
==
e
(d) Using its definition, express the potential energy of a dipole in an electric field:
cospEU == Ep rr
Evaluate U for = 0: ( )( )J1020.3
0cosN/C100.4nm5.024
4
== eU
Evaluate U for = 90: ( )( )0
90cosN/C100.4nm5.0 4
== eU
Evaluate U for = 30: ( )( )
J1077.2
30cosN/C100.4nm5.024
4
== eU
*59 Picture the Problem We can combine the dimension of an electric field with the dimension of an electric dipole moment to prove that, in any direction, the dimension of the far field is proportional to [ ]31 L and, hence, the electric field far from the dipole falls off as 1/r3. Express the dimension of an electric field:
[ ] [ ][ ]2LkQE =
Express the dimension an electric dipole moment:
[ ] [ ][ ]LQp =
Write the dimension of charge in terms of the dimension of an electric dipole moment:
[ ] [ ][ ]LpQ =
Substitute to obtain:
[ ] [ ][ ][ ] [ ][ ][ ][ ]32 L
pkLLpkE ==
This shows that the field E due to a dipole
Chapter 21
44
p falls off as 1/r3. 60 Picture the Problem We can use its definition to find the molecules dipole moment. From the symmetry of the system, it is evident that the x component of the dipole moment is zero. Using its definition, express the molecules dipole moment:
jip yx pp +=r
From symmetry considerations we have:
0=xp
The y component of the molecules dipole moment is:
( )( )mC1086.1
nm0.058C101.62
2
29
19
==
==
eLqLpy
Substitute to obtain: ( )jp mC1086.1 29 = r 61 Picture the Problem We can express the net force on the dipole as the sum of the forces acting on the two charges that constitute the dipole and simplify this expression to show that We can show that, under the given conditions, is also
given by
.net iF Cp=r
netFr
( ) ipdxdEx by differentiating the dipoles potential energy function with respect to x. (a) Express the net force acting on the dipole:
qq + += FFFrrr
net
Apply Coulombs law to express the forces on the two charges:
( )iEF 1 axqCqq == rr and
( )iEF 1 axqCqq +=+=+ rr
Substitute to obtain: ( ) ( )ii
iiF2
11net
CpaqC
axqCaxqC
==++=r
where p = 2aq.
The Electric Field 1: Discrete Charge Distributions
45
(b) Express the net force acting on the dipole as the spatial derivative of U:
[ ]i
iiF
net
dxdEp
Epdxd
dxdU
xx
xx
=
==r
62 Picture the Problem We can express the force exerted on the dipole by the electric field as dU/dr and the potential energy of the dipole as pE. Because the field is due to a point charge, we can use Coulombs law to express E. In the second part of the problem, we can use Newtons 3rd law to show that the magnitude of the electric field of the dipole along the line of the dipole a distance r away is approximately 2kp/r3. (a) Express the force exerted by the electric field of the point charge on the dipole:
rF drdU=r
where is a unit radial vector pointing from Q toward the dipole.
r
Express the potential energy of the dipole in the electric field:
2rkQppEU ==
Substitute to obtain: rrF 2 32 r
kQprkQp
drd =
=r
(b) Using Newtons 3rd law, express the force that the dipole exerts on the charge Q at the origin:
FFrr =Qon or rr on FF Q =
and FF Q =on
Express in terms of the field in
which Q finds itself: QFon
QEF Q =on
Substitute to obtain: 3
2rkQpQE = 32r
kpE = General Problems *63 Picture the Problem We can equate the gravitational force and the electric force acting on a proton to find the mass of the proton under the given condition. (a) Express the condition that must be satisfied if the net force on the
eg FF =
Chapter 21
46
proton is zero:
Use Newtons law of gravity and Coulombs law to substitute for Fg and Fe:
2
2
2
2
rke
rGm =
Solve for m to obtain: Gkem =
Substitute numerical values and evaluate m:
( ) kg1086.1kg/mN1067.6C/mN1099.8C106.1 92211
22919
=
=m
(b) Express the ratio of Fe and Fg:
2p
2
2
2p
2
2
Gmke
rGm
rke
=
Substitute numerical values to obtain: ( )( )( )( ) 362272211
219229
2p
2
1024.1kg1067.1kg/mN1067.6
C106.1C/mN1099.8 ==
Gmke
64 Picture the Problem The locations of the charges q1, q2 and q2 and the points at which we are calculate the field are shown in the diagram. From the diagram it is evident that Er
along the axis has no y component. We can use Coulombs law for Er
due to a point charge and the superposition principle to find E
rat points P1 and P2. Examining the
distribution of the charges we can see that there are two points where E = 0. One is between q2 and q3 and the other is to the left of q1.
The Electric Field 1: Discrete Charge Distributions
47
Using Coulombs law, express the electric field at P1 due to the three charges:
i
iii
EEEE
2,3
32,2
22,1
1
2,3
32,2
22,1
1
111
111
3211
++=
++=++=
PPP
PPP
qqqP
rq
rq
rqk
rkq
rkq
rkq
rrrr
Substitute numerical values and evaluate
1PEr
:
( ) ( ) ( ) ( )( ) i
iE
N/C1014.1
cm2
C5cm3
C3cm4
C5/CmN1099.8
8
222229
1
=
++= Pr
Express the electric field at P2:
i
EEEE
2,3
32,2
22,1
1
222
3212
++=
++=
PPP
qqqP
rq
rq
rqk
rrrr
Substitute numerical values and evaluate 2P
Er
:
( ) ( ) ( ) ( )( ) i
iE
N/C1074.1
cm14
C5cm15
C3cm16
C5/CmN1099.8
6
222229
2
=
+
+= Pr
Letting x represent the x coordinate of a point where the magnitude of the electric field is zero, express the condition that E = 0 for the point between x = 0 and x = 1 cm:
02,3
32,2
22,1
1 =
++=
PPPP r
qrq
rqkE
or
( ) ( ) 0-cm1C5C3
cm1C5
222 =++
xxx
Solve this equation to obtain: cm417.0=x
For x < 1 cm, let y = x to obtain: ( ) ( ) 0cm1
C5C3cm1C5
222 =+ yyy
Solve this equation to obtain: cm95.6=x and cm95.6=y
Chapter 21
48
65 Picture the Problem The locations of the charges q1, q2 and q2 and the point P2 at which we are calculate the field are shown in the diagram. The electric field on the x axis due to the dipole is given by 3dipole 2 xkpE
rr = where ip 2 1aq=r . We can use Coulombs law for E
rdue to a point charge and the superposition principle to find E
rat point P2.
Express the electric field at P2 as the sum of the field due to the dipole and the point charge q2: ( )
i
ii
ii
EEE
4
22
2
21
2
22
31
22
3
dipole 22
+=
+=
+=+=
qx
aqxk
xkq
xaqk
xkq
xkp
qP
rrr
where a = 1 cm. Substitute numerical values and evaluate
2PEr
:
( ) ( )( ) ( )iiE N/C1073.1C3cm15 cm1C54m1015 C/mN1099.8 622229
2=
+
=
P
r
64. Problem ofwith that agreement excellent in isresult this,than greatermuch not is i.e., interest, ofpoint the todistance theof 10%
thanmore is dipole theof charges two theof separation theWhile
ax
*66 Picture the Problem We can find the percentage of the free charge that would have to be removed by finding the ratio of the number of free electrons ne to be removed to give the penny a charge of 15 C to the number of free electrons in the penny. Because were assuming the pennies to be point charges, we can use Coulombs law to find the force of repulsion between them. (a) Express the fraction f of the free charge to be removed as the quotient of the number of electrons to be removed and the number of free
Nnf e=
The Electric Field 1: Discrete Charge Distributions
49
electrons: Relate N to Avogadros number, the mass of the copper penny, and the molecular mass of copper:
Mm
NN =
A
MmNN A=
Relate ne to the free charge Q to be removed from the penny:
[ ]enQ = e eQn =e
AA
meNQM
MmNe
Q
f ==
Substitute numerical values and evaluate f: ( )( )
( )( )( ) %1029.31029.3mol106.02C101.6g3 g/mol5.63C15 7912319 === f (b) Use Coulombs law to express the force of repulsion between the two pennies:
( )2
2e
2
2
renk
rkqF ==
Substitute numerical values and evaluate F: ( )( ) ( )
( ) N4.32m25.0C106.11038.9/CmN1099.8
2
219213229
==
F
67 Picture the Problem Knowing the total charge of the two charges, we can use Coulombs law to find the two combinations of charge that will satisfy the condition that both are positive and hence repel each other. If just one charge is positive, then there is just one distribution of charge that will satisfy the conditions that the force is attractive and the sum of the two charges is 6 C. (a) Use Coulombs law to express the repulsive force each charge exerts on the other:
22,1
21
rqkqF =
Express q2 in terms of the total charge and q1:
12 qQq =
Chapter 21
50
Substitute to obtain:
( )22,1
11
rqQkqF =
Substitute numerical values to obtain: ( ) ( )[ ]
( )2211
229
m3C6/CmN108.99mN8 qq =
Simplify to obtain:
( ) ( ) 0C01.8C6 2121 =++ qq
Solve to obtain:
C01.2andC99.3 21 == qq or
C99.3andC01.2 21 == qq
(b) Use Coulombs law to express the attractive force each charge exerts on the other:
22,1
21
rqkqF =
Proceed as in (a) to obtain: ( ) ( ) 0C01.8C6 2121 =+ qq
Solve to obtain:
C12.1andC12.7 21 == qq 68 Picture the Problem The electrostatic forces between the charges are responsible for the tensions in the strings. Well assume that these are point charges and apply Coulombs law and the principle of the superposition of forces to find the tension in each string. Use Coulombs law to express the net force on the charge +q:
qq FFT 421 +=
Substitute and simplify to obtain: ( ) ( )( ) 2
2
2213
242
dkq
dqkq
dqkqT =+=
Use Coulombs law to express the net force on the charge +4q:
qq FFT 22 +=
Substitute and simplify to obtain: ( )( ) ( )( ) 2
2
2229
2442
dkq
dqkq
dqqkT =+=
The Electric Field 1: Discrete Charge Distributions
51
*69 Picture the Problem We can use Coulombs law to express the force exerted on one charge by the other and then set the derivative of this expression equal to zero to find the distribution of the charge that maximizes this force. Using Coulombs law, express the force that either charge exerts on the other:
221
DqkqF =
Express q2 in terms of Q and q1: 12 qQq =
Substitute to obtain: ( )2
11
DqQkqF =
Differentiate F with respect to q1 and set this derivative equal to zero for extreme values:
( )[ ]( )[ ]
extremafor0
1 112
111
21
=+=
=
qQqDk
qQqdqd
Dk
dqdF
Solve for q1 to obtain: Qq 211 =
and QqQq 2112 ==
To determine whether a maximum or a minimum exists at Qq 211 = , differentiate F a second time and evaluate this derivative at Qq 211 = :
[ ]( )
. oftly independen 0
2
2
1
2
11
221
2
qDk
qQdqd
Dk
dqFd
R2. We also know that the direction of an electric field at any point is determined by the direction of the electric force acting on a positively charged object located at that point. From the application of Gausss law we know that the electric field in both of these regions is not zero and is given by:
2n rkQE =
A positively charged object placed in either of these regions would experience an attractive force from the charge Q located at the center of the shell. correct. is )(b
The Electric Field 2: Continuous Charge Distributions
81
*10 Determine the Concept We can decide what will happen when the conducting shell is grounded by thinking about the distribution of charge on the shell before it is grounded and the effect on this distribution of grounding the shell. The negative point charge at the center of the conducting shell induces a positive charge on the inner surface of the shell and a negative charge on the outer surface. Grounding the shell attracts positive charge from ground; resulting in the outer surface becoming electrically neutral. correct. is )(b
11 Determine the Concept We can apply Gausss law to determine the electric field for r < R1 and r > R2. We also know that the direction of an electric field at any point is determined by the direction of the electric force acting on a positively charged object located at that point. From the application of Gausss law we know that the electric field in the region r < R1
is given by 2n rkQE = . A positively charged object placed in the region r < R1 will
experience an attractive force from the charge Q located at the center of the shell. With the conducting shell grounded, the net charge enclosed by a spherical Gaussian surface of radius r > R2 is zero and hence the electric field in this region is zero.
correct. is )(c
12 Determine the Concept No. The electric field on a closed surface is related to the net flux through it by Gausss law: 0insideS == QEdA . can be zero without E being zero everywhere. If the net flux through the closed surface is zero, the net charge inside the surface must be zero by Gausss law. 13 False. A physical quantity is discontinuous if its value on one side of a boundary differs from that on the other. We can show that this statement is false by citing a counterexample. Consider the field of a uniformly charged sphere. is discontinuous at the surface, E is not. Estimation and Approximation *14 Picture the Problem Well assume that the total charge is spread out uniformly (charge density = ) in a thin layer at the bottom and top of the cloud and that the area of each
Chapter 22
82
surface of the cloud is 1 km2. We can then use the definition of surface charge density and the expression for the electric field at the surface of a charged plane surface to estimate the total charge of the cloud. Express the total charge Q of a thundercloud in terms of the surface area A of the cloud and the charge density :
AQ =
Express the electric field just outside the cloud: 0
= E
Solve for :
E0=
Substitute for to obtain:
EAQ 0=
Substitute numerical values and evaluate Q: ( )( )( ) C6.26km1V/m103mN/C1085.8 262212 == Q
Remarks: This charge is in reasonably good agreement with the total charge transferred in a lightning strike of approximately 30 C. 15 Picture the Problem Well assume that the field is strong enough to produce a spark. Then we know that field must be equal to the dielectric strength of air. We can then use the relationship between the field and the charge density to estimate the latter. Suppose the field is large enough to produce a spark. Then:
V/m103 6E
Because rubbing the balloon leaves it with a surface charge density of + and the hair with a surface charge density of , the electric field between the balloon and the hair is:
02= E
Solve for : E02=
Substitute numerical values and evaluate : ( )( ) 2562212 C/m1031.5V/m103mN/C1085.82 ==
The Electric Field 2: Continuous Charge Distributions
83
16 Picture the Problem For x > r, we can approximate the ring charge by a point charge.
For x r, use Coulombs law for the electric field due to a point charge to obtain:
( ) 22
2 xrk
xkQxEx
==
(c) Evaluate Ex at x = 5 m:
( ) ( )( ) ( )( ) N/C54.2m5 C/m6.3cm5.2/CmN1099.8m5 222229
== xE
(d) Evaluate Ex at x = 5 cm:
( ) ( )( ) ( )( ) N/C1054.2m05.0 C/m6.3cm5.2/CmN1099.8cm5 4222229
== xE Note that this is a very poor approximation because x = 2r is not much greater than r.
Calculating Er
From Coulombs Law *17 Picture the Problem We can use the definition of to find the total charge of the line of charge and the expression for the electric field on the axis of a finite line of charge to evaluate Ex at the given locations along the x axis. In part (d) we can apply Coulombs law for the electric field due to a point charge to approximate the electric field at x = 250 m. (a) Use the definition of linear charge density to express Q in terms of :
( )( ) nC17.5m5nC/m3.5 === LQ
Express the electric field on the axis of a finite line charge:
( ) ( )LxxkQxEx = 000
Chapter 22
84
(b) Substitute numerical values and evaluate Ex at x = 6 m:
( ) ( )( )( )( )N/C26.2
m5m6m6nC17.5/CmN108.99m6
229
=
=xE
(c) Substitute numerical values and evaluate Ex at x = 9 m:
( ) ( )( )( )( )N/C37.4
m5m9m9nC17.5/CmN108.99m9
229
=
=xE
(d) Substitute numerical values and evaluate Ex at x = 250 m:
( ) ( )( )( )( ) mN/C57.2m5m502m502 nC17.5/CmN108.99m502229
==xE
(e) Use Coulombs law for the electric field due to a point charge to obtain:
( ) 2xkQxEx =
Substitute numerical values and evaluate Ex(250 m):
( ) ( )( )( ) mN/C52.2m250 nC17.5/CmN108.99m250 2229
==xE Note that this result agrees to within 2% with the exact value obtained in (d). 18 Picture the Problem Let the charge densities on the two plates be 1 and 2 and denote the three regions of interest as 1, 2, and 3. Choose a coordinate system in which the positive x direction is to the right. We can apply the equation for Er
near an infinite plane of charge and the superposition of fields to find the field in each of the three regions.
The Electric Field 2: Continuous Charge Distributions
85
(a) Use the equation for Er
near an infinite plane of charge to express the field in region 1 when 1 = 2 = +3 C/m2:
i
ii
EEE
4
22 21
1 21
k
kk
==
+= rrr
Substitute numerical values and evaluate :1Er
( )( ) ( )iiE N/C1039.3C/m3/CmN1099.84 522291 == r
Proceed as above for region 2:
022
22 212 21==
=+=ii
iiEEE
kk
kkrrr
Proceed as above for region 3:
( )( )( )i
i
i
iiEEE
N/C1039.3
C/m3/CmN1099.84
4
22
5
2229
213 21
==
=+=+=
k
kkrrr
The electric field lines are shown to the right:
(b) Use the equation for Er
near an infinite plane of charge to express and evaluate the field in region 1 when 1 = +3 C/m2 and 2 = 3 C/m2:
022
22 211 21==
=+=ii
iiEEE
kk
kkrrr
Proceed as above for region 2:
( )( )( )i
i
i
iiEEE
N/C1039.3
C3/CmN1099.84
4
22
5
229
211 21
==
=+=+=
k
kkrrr
Chapter 22
86
Proceed as above for region 3:
022
22 213 21==
=+=ii
iiEEE
kk
kkrrr
The electric field lines are shown to the right:
19 Picture the Problem The magnitude of the electric field on the axis of a ring of charge
is given by ( ) ( ) 2322 axkQxxEx += where Q is the charge on the ring and a is the radius of the ring. We can use this relationship to find the electric field on the x axis at the given distances from the ring. Express E
ron the axis of a ring charge:
( ) ( ) 2322 ax kQxxEx +=
(a) Substitute numerical values and evaluate Ex for x = 1.2 cm:
( ) ( )( )( )( ) ( )[ ] N/C1069.4cm5.8cm2.1 cm2.1C75.2/CmN1099.8cm2.1 52322229
=+
= xE
(b) Proceed as in (a) with x = 3.6 cm:
( ) ( )( )( )( ) ( )[ ] N/C1013.1cm5.8cm6.3 cm6.3C75.2/CmN1099.8cm6.3 62322229
=+
= xE
(c) Proceed as in (a) with x = 4.0 m:
( ) ( )( )( )( ) ( )[ ] N/C1054.1cm5.8m4 m4C75.2/CmN1099.8m4 32322229
=+
= xE
(d) Using Coulombs law for the electric field due to a point charge, express Ex:
( ) 2xkQxEx =
The Electric Field 2: Continuous Charge Distributions
87
Substitute numerical values and evaluate Ex at x = 4.0 m:
( ) ( )( )( ) N/C1055.1m4 C75.2/CmN1099.8m4 32229
== xE
ring. theis than m 4 nearer is chargepoint thebecauselarger slightly isIt ).(Part in obtainedresult with the1% within toagreesresult This
=xc
20
Picture the Problem We can use ( )
+= 2212 RxxkxEx , the expression for the
electric field on the axis of a disk charge, to find Ex at x = 0.04 cm and 5 m. Express the electric field on the axis of a disk charge:
( )
+= 2212 RxxkxEx
(a) Evaluate this expression for x = 0.04 cm:
( )( ) ( ) ( )N/C1000.2
cm5.2cm0.04
cm04.01C/m6.3C/mN1099.82
5
22
2229
=
+= xE
This value is about 1.5% smaller than the approximate value obtained in Problem 9. (b) Proceed as in (a) for x = 5 m:
( )( ) ( ) ( ) N/C54.2cm2.5m5m51C/m6.3/CmN1099.82
22
2229 =
+= xE
Note that the exact and approximate (from Problem 16) agree to within 1%. 21 Picture the Problem We can use the definition of to find the total charge of the line of charge and the expression for the electric field on the perpendicular bisector of a finite line of charge to evaluate Ey at the given locations along the y axis. In part (e) we can apply Coulombs law for the electric field due to a point charge to approximate the electric field at y = 4.5 m. (a) Use the definition of linear ( )( ) nC300.0cm5nC/m6 === LQ
Chapter 22
88
charge density to express Q in terms of :
Express the electric field on the perpendicular bisector of a finite line charge:
( ) ( ) 2221212
yLL
ykyEy +
=
(b) Evaluate Ey at y = 4 cm:
( ) ( ) ( )( )( ) ( ) kN/C43.1m04.0m025.0m05.0nC/m6
m04.0/CmN1099.82cm4
2221229 =
+=yE
(c) Evaluate Ey at y = 12 cm:
( ) ( ) ( )( )( ) ( ) N/C183m12.0m025.0m05.0nC/m6
m12.0/CmN1099.82cm12
2221229 =
+=yE
(d) Evaluate Ey at y = 4.5 m:
( ) ( ) ( )( )( ) ( ) N/C133.0m5.4m025.0m05.0nC/m6
m5.4/CmN1099.82m.54
2221229 =
+=yE
(e) Using Coulombs law for the electric field due to a point charge, express Ey:
( ) 2ykQyEy =
Substitute numerical values and evaluate Ey at y = 4.5 m:
( ) ( )( )( ) N/C133.0m5.4 nC3.0/CmN1099.8m5.4 2229
==yE This result agrees to three decimal places with the value calculated in Part (d). 22 Picture the Problem The electric field on the axis of a disk charge is given by
+= 2212 axxkqEx . We can equate this expression and 021 2= xE and
solve for x. Express the electric field on the axis of a disk charge:
+= 2212 axxkqEx
The Electric Field 2: Continuous Charge Distributions
89
Were given that: 021 2= xE
Equate these expressions:
+= 22012
4 axxk
Simplify to obtain:
+= 22012
4 axxk
or, because k = 1/40, 22
121
axx+=
Solve for x to obtain:
3ax =
23
Picture the Problem We can use ( ) 2322 ax kQxEx += to find the electric field at the given distances from the center of the charged ring. (a) Evaluate Ex at x = 0.2a: ( ) ( )( )[ ]
2
2322
189.0
2.0
2.02.0
akQ
aaakQaEx
=+
=
(b) Evaluate Ex at x = 0.5a: ( ) ( )( )[ ]
2
2322
358.0
5.0
5.05.0
akQ
aaakQaEx
=+
=
(c) Evaluate Ex at x = 0.7a: ( ) ( )( )[ ]
2
2322
385.0
7.0
7.07.0
akQ
aaakQaEx
=+
=
(d) Evaluate Ex at x = a: ( ) [ ] 22322 354.0 akQaa kQaaEx =+=
Chapter 22
90
(e) Evaluate Ex at x = 2a: ( ) ( )[ ] 22322 179.02 22 akQaa kQaaEx =+=
The field along the x axis is plotted below. The x coordinates are in units of x/a and E is in units of kQ/a2.
-0.4
-0.2
0.0
0.2
0.4
-3 -2 -1 0 1 2 3
x /a
E x
24
Picture the Problem We can use
+= 2212 RxxkEx , where R is the radius of
the disk, to find the electric field on the axis of a disk charge. Express Ex in terms of 0:
+=
+=
220
220
12
142
Rxx
RxxEx
(a) Evaluate Ex at x = 0.2a: ( ) ( )
0
220
2804.0
2.0
2.012
2.0
=
+=
aa
aaEx
The Electric Field 2: Continuous Charge Distributions
91
(b) Evaluate Ex at x = 0.5a: ( ) ( )
0
220
2553.0
5.0
5.012
5.0
=
+=
aa
aaEx
(c) Evaluate Ex at x = 0.7a: ( ) ( )
0
220
2427.0
7.0
7.012
7.0
=
+=
aa
aaEx
(d) Evaluate Ex at x = a: ( )
0
220
2293.0
12
=
+=
aa
aaEx
(e) Evaluate Ex at x = 2a: ( ) ( )
0
220
2106.0
2
212
2
=
+=
aa
aaEx
The field along the x axis is plotted below. The x coordinates are in units of x/a and E is in units of .2 0
0.0
0.4
0.8
1.2
1.6
2.0
-3 -2 -1 0 1 2 3
x/R
E x
Chapter 22
92
*25 Picture the Problem (a) The electric field on the x axis of a disk of radius r carrying a surface charge density is given by:
+= 2212 rxxkEx
(b) The electric field due to an infinite sheet of charge density is independent of the distance from the plane and is given by:
kE 2plate =
A spreadsheet solution is shown below. The formulas used to calculate the quantities in the columns are as follows:
Cell Content/Formula Algebraic Form B3 9.00E+09 k B4 5.00E10 B5 0.3 r A8 0 x0 A9 0.01 x0 + 0.01 B8 2*PI()*$B$3*$B$4*(1A8/
(A8^2+$B$5^2)^2)^0.5)
+ 2212 rxxk
C8 2*PI()*$B$3*$B$4 k2
A B C 1 2 3 k= 9.00E+09 Nm^2/C^24 sigma= 5.00E-10 C/m^2 5 r= 0.3 m 6 7 x E(x) E plate 8 0.00 28.27 28.3 9 0.01 27.33 28.3
10 0.02 26.39 28.3 11 0.03 25.46 28.3 12 0.04 24.54 28.3 13 0.05 23.63 28.3 14 0.06 22.73 28.3 15 0.07 21.85 28.3
73 0.65 2.60 28.3 74 0.66 2.53 28.3 75 0.67 2.47 28.3 76 0.68 2.41 28.3 77 0.69 2.34 28.3
The Electric Field 2: Continuous Charge Distributions
93
78 0.70 2.29 28.3 The following graph shows E as a function of x. The electric field from an infinite sheet with the same charge density is shown for comparison the magnitude of the electric fields differ by more than 10 percent for x = 0.03 m.
0
5
10
15
20
25
30
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
x (m)
E (N
/C
E
E plate
26 Picture the Problem Equation 22-10 expresses the electric field on the axis of a ring charge as a function of distance along the axis from the center of the ring. We can show that it has its maximum and minimum values at 2ax += and 2ax = by setting its first derivative equal to zero and solving the resulting equation for x. The graph of Ex will confirm that the maximum and minimum occur at these coordinates. Express the variation of Ex with x on the axis of a ring charge:
( ) 2322 ax kQxEx += Differentiate this expression with respect to x to obtain:
( )( ) ( )
( )( ) ( )( ) ( )( ) ( ) ( )( )322
212222322
322
2122232322
322
23222322
2322
32ax
axxaxkQax
xaxxaxkQ
ax
axdxdxax
kQaxx
dxdkQ
dxdEx
+++=+
++=+
++=
+=
Set this expression equal to zero for extrema and simplify:
( ) ( )( ) 03 322212222322
=+++
axaxxax
,
( ) ( ) 03 212222322 =++ axxax ,
Chapter 22
94
and 03 222 =+ xax
Solve for x to obtain: 2
ax = as our candidates for maxima or minima.
A plot of E, in units of kQ/a2, versus x/a is shown to the right. This graph shows that E is a minimum at 2ax = and a maximum at 2ax = .
-0.4
-0.2
0.0
0.2
0.4
-3 -2 -1 0 1 2 3
x/a
E x
27 Picture the Problem The line charge and point (0, y) are shown in the diagram. Also shown is a line element of length dx and the field E
rd its charge produces at (0, y). We
can find dEx from Er
d and then integrate from x = x1 to x = x2.
Express the x component of E
rd :
( ) dxyx xkdx
yxx
yxk
dxyx
kdEx
2322
2222
22 sin
+=++=
+=
The Electric Field 2: Continuous Charge Distributions
95
Integrate from x = x1 to x2 to obtain: ( )
+++=
+++=
+=
+=
221
222
221
222
22
2322
11
12
1
2
1
yxy
yxy
yk
yxyxk
yxk
dxyx
xkE
x
x
x
xx
From the diagram we see that:
222
2cosyx
y+= or
=
yx21
2 tan and
221
1cosyx
y+= or
=
yx11
1 tan
Substitute to obtain: [ ][ ]12
12
coscos
coscos
=
+=
yk
ykEx
28 Picture the Problem The diagram shows a segment of the ring of length ds that has a charge dq = ds. We can express the electric field E
rd at the center of the ring
due to the charge dq and then integrate this expression from = 0 to 2 to find the magnitude of the field in the center of the ring. (a) and (b) The field E
rd at the
center of the ring due to the charge dq is:
ji
EEEsincos dEdE
ddd yx=
+= rrr (1)
The magnitude dE of the field at the center of the ring is: 2r
kdqdE =
Chapter 22
96
Because dq = ds: 2r
dskdE =
The linear charge density varies with according to () = 0 sin :
20 sin
rdskdE =
Substitute rd for ds: r
dkr
rdkdE sinsin 020 ==
Substitute for dE in equation (1) to obtain:
j
iE
sin
cossin
20
0
rdk
rdkd
=r
Integrate E
rd from = 0 to 2:
j
j
j
iE
0
sin
2sin2
0
0
2
0
20
2
0
0
rkrk
dr
k
dr
k
=
=
=
r
. is magnitude its anddirection negative in the isorigin at the field The 0rky
29 Picture the Problem The line charge and the point whose coordinates are (