Post on 23-Mar-2022
The Future of Automotive
AutomotiveMaterialSolutions
FUTURE
COMPETITIVE
INNOVATIVE
LOTTE Chemical is committed to creating value beyond customer’s expectation, at the center of future of automotive based on competitive products, innovative solution, and in close partnership with you.
03
Contents
Product Portfolio 04 Product 06 Global Awards 23 Product Selection Guide 24 At a Glance 26 Global Network 27
04 05
INTERIOR
• Low TVOC ABS• Low Gloss ABS, PC/ABS• Low Gloss, Emotional Feeling PC/ASA• Light Diffusion PC• High Flow PC/ABS• High Heat/Chemical Resistant PC/ABS, PC/PBT• Chemical Resistant PC/ABS• Low TVOC/Odor PP, LFT• High Appearance LFT• High Impact Foamed PP
Fresh Interior Upscale Design
EXTERIOR LIGHTING STRUCTURE
04 05
• High Weatherable/Impact PC• High Gloss/Low Gas PBT• High Gloss/Low Gas PC/ABS• High Modulus/Heat Resistant PP
Functionality & Productivity
Optical Solution
Product Portfolio
• Conductive/High Heat Resistant PA/PPE/CNT• Dimensional Stability PBT/ASA/GF• High Flow/Surface Quality PBT/PET/GF• High Heat Resistant PPA• High Flow LFT• High Heat Resistant LFT
Light-weight & Metal Replacement
Part-integrated Design
• Metal Plating ABS & PC/ABS • High Weatherable ASA• High Weatherable/Impact PC/ASA• High Modulus PC/PET• High Flow/Impact PC/PBT• High Impact PP, LFT • High Weatherable PP, LFT• High Flow/Paint-free PP• Continuous Fiber Reinforced Composite (WLFT, 3D-Tow)
Weatherability Safety
Low TVOC ABS, PP Comp’d
BENEFITS CHARACTERISTICS
APPLICATIONS
• Center console
• Window switch panel
• Door upper trim
Low TVOC
Heat Resistance
SR-0320LT10 PPM
Ref. A
Ref. B
60
SR-0320LT Reference
HDT 94°C 92°C
Heat Sagging (90°C) 4mm 5mm
Heat Sagging (95°C) 9mm 10mm
Low Gloss ABS, PC/ABS, PC/ASA
BENEFITS
APPLICATIONS
• Low gloss
• High weatherability
• High impact strength
• Sheet
• Gloss modifier
• Door panel
• Air vent bezel
• Over head console
0706
INTERIOR
06
Fresh Interior
Upscale Design
Heat Resistant
General
SR-0300
SR-0310FM
SR-0320 K
SR-0325LT
SR-0330M
SR-0340M
Low TVOC
SR-0320LI (High Impact)
SR-0320LT
SR-0325L
SR-0325LT
SR-0330L
SR-0340L
Low Gloss
Super Low Gloss
SL-0100
Heat Resistant
LH-0300
ABS
High Impact
PP2320E
High Modulus
PP1320(E)
PP1330(E)
Low TVOC
PP1320(LE)
PP1330(LE)
High Appearance
PP1330T
PP1340T
Foamed
PP2320F
LFT
General
HP-1000XA
HP-1000X
High Flow
WP-1069
WP-1089
Low Gloss
LH-1049
LH-1069
Luminous
LX-1098F
Chemical Resistant
WP-1059J
HP-1000C
HP-1000XC
Low TVOC
HP-1000XL
PC/ABS
Low Gloss
WR-7250H
EF(Emotional Feeling)
IF-7900
PC/ASA
WP-1100
WP-1200
PC/ABS/GF
AE-3080C
PC/PBT
Light Diffusion
TP-1020
TP-1020U
TP-1025U
High Impact
IV-1025U
IV-1075C (Chemical Resistant)
PC
High Impact/Modulus
HSP-387
QHCA-352M
GHPP-362T-T1P
High Impact/ Scratch Resistant
HIP-371(S)
HIP-372
Scratch Resistant
HSP-375
HGW-353
HCA-352S
JHC-371/372/374
JHC-3505
Foamed
FM-365
PP Comp’d
Heat Resistant ABS
SR-0320LT
SR-0325LT
SR-0320LI
SR-0330L
SR-0340L
PP Comp’d
QHCA-352M
• Low TVOC:
VDA277(<50/g)
VDA278 (VOC<50/g)
• Low Odor:
VDA270
ABS
SL-0100 (Extrusion)
LH-0300
PC/ABS
LH-1049
LH-1069
LX-1098F(Luminous)
PC/ASA
WR-7250H
IF-7900 (EF)
LOTTE
LH-1069 LH-1049
Gloss = 2.0 Gloss = 1.5
Ref.
Gloss = 3.0 Gloss = 2.0
Grain type
Glossy Rough grain Fine grain
LH-1069 33 5 2
General PC/ABS 95 8 5
Gloss Level Comparison (Fine grain)
Gloss Level by Grain (LH-1069)
CHARACTERISTICS
08 09
TP-1020 Reference
HCO-product
surface
comparison
After
injection
molding
After
painting
Result
High flowability and thermal stability
→ High-quality appearance and a reduction in internal stress during injection molding process
Improved painting quality as a result of excellent appearance
→ Uniform surface for painting
BENEFITS
Fewer holes on the painted surface Many holes on the painted surface
Optical property (Texted LED lighting) becomes available through laser cutting (Luminance, uniformity of luminance)
* HCO: Heat Control Overlay
Light Diffusion PCTP-1020
TP-1020U
TP-1025U
Excellent Quality of Appearance: Painting quality improved
CHARACTERISTICS
Excellent Quality of Appearance: Puddle issue addressed
Improved yield ratio of injection molding and painting, based on high flowability and thermal stability
TP-1020 Reference
• High flowability
• High impact strength
• Painting stability
• Diffusion properties:
High luminance, uniformity
APPLICATIONS
• Center fascia:
Overlay housing
• Button (LED lighting)
• Window shield lens
• 2-shot molding
Foamed PP Comp’d
High Appearance LFT
FM-365
PP1330T
PP1340T
BENEFITS
BENEFITS
CHARACTERISTICS
CHARACTERISTICS
APPLICATIONS
APPLICATIONS
• Light-weight (>20%)
• A reduction in sink marks on the surface
• Insulation and sound absorption
• Surface quality (Fiber cluster “0”)
• Dimensional Stability
• Door trim
• Crash pad
• Over Head Console
• Step Pad for Truck
The formation of uniform cell structure, Excellent Quality of Appearance
Excellent surface quality
Cell structure Surface
FM-365
Ref.(Talc15%)
Surface quality test (The surface of molded products)
Fiber Cluster Class
PP1340T 0 Class A
Ref. 20 Class C
PP1340T-Inferior Ref.-Good
10 11
BENEFITS CHARACTERISTICS
APPLICATIONS
WP-1089
WP-1069
Reference (PC 65%)
95°C Very bad
bad
normal
good
Very good
100°C
105°C
110°C
115°C
2530
3540
3035
4045
50
55
60
65
High Flow PC/ABSWP-1069
WP-1089•High flowability
•Heat stability
• Center fascia
• Air vent
Property Balance
Chemical Resistant PC/ABS, PC/PBT
Izod Impact, notched, 23°C (kgf·cm/cm)
Heat stability (270°C)
Izod Impact, notched, -30°C (kgf·cm/cm)
Spiral flow, 250°C, 2mm
(cm)
HDT
Heat Stability (Gloss Change, 270°C * 10min.)
WP-1069 Reference
Gloss (60’)
Before After Before After
99.1 95.9 101.8 87.6
Gloss = 3.2Before After Before
Gas silver Flow mark and discoloration
Gloss = 4.2After
PC/ABS
HP-1000C
HP-1000XC
PC/PBT
AE-3080C
CHARACTERISTICS
BENEFITS
BENEFITS
• Paintability
• Chemical resistance: (Freshener)
•UV Stability
• Chemical resistance: Freshener
• Hydrolysis resistance
APPLICATIONS
• Center Fascia Overlay panel
• Cover console upper frame
• Air vent housing & deco
• Arm rest upper/lower cover
AE-3080C General PC/ABS
ISO-IZOD Degradation Rate (85/85% 168H)
20% 15%
Light Resistance (84MJ)
1.5 NG
Chemical Resistance
ESCR 2.1% Fabric deodorizer
PC/PBT: UV stability, chemical resistance, and hydrolysis resistance
Chemical resistant PC Line-up Comparison
AE-3080C
Chemical Resistant PC/ABS
General PC/ABS
Specific Gravity
Chemical Resistant
Hydrolysis resistance
UV Stability
Processability
Heat Resistant
EXTERIOR
11
Weatherability Safety
WR-7000
WX-7010
WX-7030
PC/ASA
High Impact
AE-3060
AE-3063I (at low temp.)
PC/PBT
General
AE-2030
Reinforced
AE-2130
AE-2150
AE-2230
PC/PET
WP-1101M (MF 10%)
WP-1170M (MF 17%)
PC/ABS/MF
Metal Plating
MP-0160 R
MP-0670
Blow Molding
BM-0320J
BM-0325H
Painting
PT-0180 H
PT-0180C
Heat Resistant
SR-0320 K
SR-0325, 0325LT
ABS
High Impact
CRX-15000(U)
SRX-373(M)
GHE-400NPH
High Weatherability
A-352U
A-354U
High Heat
GLW-373
G-152
G-153
Expanded (Blow)
BF-330E
BF-620E
PP Comp’d
High Impact
PP3320B
High Modulus
PP1330ET
LFT
WLFT
WLFT511BL
3D-Tow
TOW-PPGF40
Composite
High Impact
HP-1000XA
HP-1000X
High Flow
WP-1059
WP-1069
WP-1089
Metal Plating
WP-1041(G)
WP-1051
WP-1061
PC/ABS
General
WX-9950
High Weatherability
WX-9950UV
WX-9950U
High Impact
WX-9950S
ASA/PMMA
High Impact/Flow
WR-9120 J
WX-9310J
WR-9330I
High Weatherability
WX-9300UV
WX-9310UV
WX-9330UV
ASA
Air freshener chemical resistance test (¼ Ellipse Jig method)
No crack was found on the surface after 72 hours passed since the application of air fresheners.
Specimen
Application of air
freshener A and B
The Combination of Functional Additives: Enhanced chemical resistance
¼ Ellipse Jig
Metal Plating Materials with High Adhesion StrengthABS
MP-0160 R
MP-0670
PC/ABS
WP-1041G
WP-1051
WP-1061 CHARACTERISTICS
Metal Plating ABS (MP-0160 R, MP-0670)
BENEFITS
• Excellent quality of appearance
• Metal adhesion
•Quality stability
APPLICATIONS
• Radiator grille
• Rear garnish
• Emblem
• Outside mirror
• Door handle
Good surface quality without pitting
Well dispersed rubber and quality consistency
Conventional Improved ABS
WP-1041G WP-1051 WP-1061
6
4
8
Pit 4.5
Adhesion 250
Pit 6.2
Adhesion 387
Regularly etched
· Matrix SAN composition optimize
. g-ABS dispersion and content control
Incompletely etched
· Rubber dispersion is not regular in SAN phase
Under etched
· Matrix SAN composition is not optimized
Pit 1.7
Adhesion 415
Metal Plating PC/ABS (WP-1041G)
Metal Plating PC/ABS – Comparison of PC Content
Schematic
Diagram
Properties
High Weatherable ASA
PC/ABS with Low PC Content
PC/ABS with High PC Content
· Reduction of etching time
· Low metal adhesion
· Low heat stability
· Increase of etching time
· High metal adhesion
· High heat stability
· High mechanical properties
* A
dh
esi
on
(N
/cm
)
PC Content (%)
HighLow
12 13
WP-1041G Reference A Reference B
WX Series
WR Series
BENEFITS
• High weatherability
• High impact strength
• Heat resistance
APPLICATIONS
• Outside mirror
•Radiator grille
•Pillar
•Spoiler
•Garnish
CHARACTERISTICS
Excellent Weatherability
GradeWeatherability (3,000 Hr.) Impact Properties
Delta E Gloss Retention IZOD FDI
General ASA 5~10 < 5% < 15 25~27
starex WX Series ≤ 3 25~40% 19~21 28~29
Performance Improvement + 40 % + 400 % + 25 % + 15 %
Grade WX-9300UV WX-9310UV WX-9330UV
Impact Resistance
FDI (N/J) 3,430 / 28 3,400 / 28 3,590 / 29
Dupont Drop (Destruction Rate)
12% 10% 10%
Weatherability
(3,000 Hr.)
dE 2.8 2.5 2.6
Gloss Retention 44% 40% 31%
MI 12 6.0 4.5
VST 98 101 103
Properties
High Weatherable PC/ASA
BENEFITS
• High weatherability
• High impact strength
• Heat stability
• High flowability
APPLICATIONS
• Radiator grille
• Outside mirror
• Roof rack
• Rear spoiler
WR-7000
WX-7010
WX-7030
CHARACTERISTICS
Property Balance
WR-7000 Reference
WR-7000 Property
Flowability
Impact resistance
WeatherabilityColor performance
Thermal stability
100
80
60
40
20
Change of Delta E (SAE J 2527)
2
4
0
6
1000KJ0KJ 2500KJ2000KJ
dE
WX-7030 Property
Change of Delta E
2
1
0
3
0 2000KJ
dF
500KJ 1000KJ 1500KJ
WX-7030 Reference
Phase stability UV stability
Color performance
Impact resistance
Thermal stability
Flowability
14 15
High Impact PC/PET High Flow/Paint-free PP Comp’d
High Impact/Modulus WLFT*
AE-2030
AE-2130
AE-2230
AE-2150
SRX-373M
WLFT511BL
BENEFITS
APPLICATIONS
• Colorability
• High Weatherability
• Scratch Resistance
• High Impact
• Pillar
• Roof rack
• Outside Mirror
• Radiator Grille
• Garnish
High Gloss ASA/PMMAWX-9950UV
WX-9950U
WX-9950
WX-9950S
Erichsen test
Ref. (Talc 14%) SRX-373M
CHARACTERISTICS
Weatherability Property Balance
Scratch Resistance
SAE J1960/J2527 (Xenon Arc)
PMMA > ASA/PMMA > ASA
ASA/PMMA > ASA
Erichsen Test
Excellent Surface Quality: Better Scratch Resistance
Thin-wall TPO
Conventional TPP
BENEFITS
APPLICATIONS
• High impact strength
• Low CLTE
• Dimensional stability
• Radiator grille
• Door handle
• Rear spoiler
• Garnish
Paintability
Scratch Resistance(Erichsen test)
WeatherabilityHeat resistance
Impact strength
100
7.5
5.0
2.5
0
ASA/PMMA
ASA
PMMA
HH ABS
1,000 2,000 3,000KJ 4,0000
2
4
6
0
dF
ASA ASA/PMMA PMMA
BENEFITS CHARACTERISTICS
APPLICATIONS
• High Flow (Thin-wall)
• High Impact/Modulus
• High Weatherability
• Scratch Resistance
• Bumper Fascia
Property Balance
MFR
FM
YS IZOD
BAD GOOD
Rear bumper back beam
LFT(GF40wt%)
WLFT(GF40wt%)
BENEFITS CHARACTERISTICS
APPLICATIONS
•Energy absorption
• High impact, modulus
• Rear bumper back beam
• Crash box
• Stiffener
Property Comparison (WLFT – LFT)
Tensile Strength
Flexural Strength High-velocity impact
Izod Impact Strength Flexural Modulus
ASA/PMMA Ref. ASA
* The data refers to the measured value based on the high gloss surface
Improved Surface Quality
Schematic Diagram Injection Molding Specimen
LOTTE PC/PET/MF Conventional LOTTE PC/PET/MF Conventional
MF dispersion optimize MF aggregation Good surface finish Flash, Flow mark
AE-2130: MF 5%, AE-2230: MF 20%
Gate
CHARACTERISTICS
PC/PET: AE-2030
PC/PET/MF: AE-2130, AE-2230, AE-2150
CLTE
Test Method Unit Condition
ASTM E831 1/-25 ~50
(Flow, xFlow)
AE-20307.7E-05
8.2E-05
Reference8.0E-05
8.6E-05
AE-2030 Reference
Gloss
(60o)
98 80
Dimension Stability (Low CLTE & Low Warpage) Surface Quality
AE-2030 has
better gloss
and shows
good
paintability
GateGateGate
* Woven Long Fiber Thermal plastic
LIGHTING
16 17
Functionality &Productivity
Optical Solution
LOTTE Reference
Non-Phosgene Process (Melt Process) Phosgene Process (Interfacial Process)
High Weatherable/Impact PC LT Series
LT-1100
LT-1220
BENEFITS
•High weatherability
•High impact strength
•Low gas
APPLICATIONS
• Head/Fog lamp lens
• Head/Fog lamp bezel
• Rear lamp reflector
CHARACTERISTICS
Eco-friendly Process
EO
EG
EC CO
PC Powder
Polycarbonate
Waste Water/NaCl
NaOH BPA COCl2 CH2Cl2
Cl2Methanol
Phenol DMC
Polycarbonate
DPC BPA
Co2
Drying/Extrusion
High Modulus/High Heat
GWL-373
A-353S
Heat Resistant
SR-0300
SR-0320 K
SR-0325LT
SR-0325 (High Flow)
SR-0330M
ABS
General, Light Diffusion
LT-1100
LT-1220
PC
High Gloss/Low Gas
HP-1000XG
High Impact at Low Temp.
HP-1000XA
High Flow
WP-1069
WP-1089
PC/ABS
General
WR-9330I
WR-9370
ASA
General
ASF-9810FL
High Flow
ASF-9810FM
Super High Flow
ASF-9860
PBT PP Comp’d
Head Lamp Lens
(Hard Coating PC Covering)
Rear Lamp Lens
(PMMA Clear Covering)
Rear Lamp Lens
(PMMA Red Covering)
결합구조
Δ E(SAE J 1960, 2500KJ)
0.4 1.5 1.3
AMECA Listing
High Weatherability
➊
➊ Substrate ➋ PC ➌ Coating ➍ PMMA (Clear) ➎ PMMA (Red)
➊ ➊➋ ➍ ➎➌
HP Series Reference
High Gloss/Low Gas PC/ABS HP-1000XG
BENEFITS
•High gloss
•Low gas
•High flowability
•High heat resistance
APPLICATIONS
•Rear lamp housing
• Center high mounted stop lamp
(CHMSL)
•Rear lamp reflector
CHARACTERISTICS
Surface after Metallization Heat Resistance Test (280˚C/10min.)
25
50
75
100
High Flowability
Low Out Gassing
HP Series Reference
Spiral Test
Melt Flow
(250°C, 2.16kgf)37g/10min 34g/10min
ppm Haze
Gas Mark
18 19
HP-1000XG Reference HP-1000XG Reference
Test condition: Cylinder temperature 280, 10min-residence shot
White Mark
Fogging Test (250°C, 1Hr)
HP Series
HP Series
Ref.Ref.
High Gloss/Low Gas PBT ASF-9810FL
ASF-9810FM
ASF-9860
BENEFITS
•Low gas
•Heat stability
•High gloss surface (Direct metallization)
CHARACTERISTICS
Improved Pinhole Issue
APPLICATIONS
•Head lamp bezel
•Fog lamp bezel
•Rear lamp reflector
Low Gas Heat Resistance (270˚C/10 min.)
Carbon Black Dispersibility
ASF-9810FM Reference
80ppm 180ppm
ASF-9810FM Reference
Fogging Test (270, 3hr) Pin-point Test
Gas & Flow Mark
Conventional LOTTE
OpticalMicroscope
(×50)
ShadingConvert
Count 21.0 10.3
Pinhole Total Area 1,231 484
Size (Diameter) 58.6 47.1
AfterBefore
PA/PPE/CNT
Conductive/ High Heat Resistant
CA-7000C
CA-7009
PBT/PET/GF
High Flow/ Surface Quality
AR-6200
AR-6300
AR-6308
AR-6508
PBT/ASA/GF
Dimensional Stability
AR-5300H (GF30%)
LFT
High Flow
PP1340HF
PP1330HF
High Heat Resistance
PP1330H
STRUCTURE PA/PPE/CNTCA-7000C
CA-7009BENEFITS
•High heat resistance
•Light-weight
•Design freedom
•Conductivity
•Dimensional stability
•Low hygroscopicity
APPLICATIONS
•Fender
•Fuel filler door
•Body panel
CHARACTERISTICS
Thermal Stability
DMTA Storage Modulus
DMTA measurement condition
· Tem. Range: 0°C ~ 275°C · Scanning Rate: 5°C/min · Frequency: 1Hz
Elas
tic M
odul
us
Temperature (°C)
10
1
100
1,000
10,000
50 100 150 200 3002500
MaterialStorage Modulus
0 200
CA-7000C 1,900 315
CA-7009 2,000 370
Reference 1,800 130
Better Surface Quality Lower Moisture Absorption
CA-7000C Reference
CA-7000C CA-7009 Reference
50 100 150 200 250
0.5
1
1.5
2
2.5
Time (days)
Wat
er
Ab
sorp
tion
0
45°C, 95%RH
Vol % of conductor
Com
duct
ivity
(ohm
-1 c
m-1)
10.1 10
100
1E-6
1E-8
1E-4
1E-2
1
CNT CF CB
Increase aspect ratio
Filler Loading (%)
CNT (Carbon Nano
Tube)
CF (Carbon Fiber)
CB (Carbon Black)
<1% >10% >15%
Time (days)
Wat
er
Ab
sorp
tio
n
100 20 30 40 50 60 70
1
2
3
4
Water Absorption
20 21
Light-weight & Metal
Replacement
Part-integrated Design
MFD Cover
Passenger Deco Bezel
Gearshift Bezel
MFD Cover
[2017]
SPE Automotive Innovation Awards Winner
[2015]
Korea NET Certification
Global Awards
2-Shot 3D pattern material technology
•Excellent pattern design with 3D 2-shot layers
- Layer 1: Transparent PC
- Layer 2: Non-painting Luminous ABS
• Cost Reduction: Surface finishing process simplification
•Designed to fit interior parts of the 2018 MY Ford ‘Fiesta’ Model
INFINO PC + starex Luminous ABS
Heat Aging PPA Solution
[2017]
Korea NET Certification
Continuous Fiber Reinforced Composite Solution
• A maximum of 60% reduction in weight and
at least 10% cost reduction compared with
the existing parts
3D Tow Insert Injection Technology
* NET (New Excellent Technology) is South Korea’s state-run certification system that recognizes and certifies the country’s new technological development in the related fields or dramatic improvement compared with the existing technologies.
* IR 52 Jang Yeong-sil Award: An industrial award given to South Korean companies and engineers who spearhead technological innovation by developing and commercializing new technology products.
•Lightweight metal plating design
•Long-term heat stability & Shield effect (oxidation blocking)
INFINO High Heat Resistant PPA Technology
[2018]
Received IR52 Jang Yeong-sil Award in Korea
[2016]
Korea NET Certification
PBT/ASA/GF 30%AR-5300H
BENEFITS CHARACTERISTICS
APPLICATIONS
•Dimensional stability
•Weight reduction
•Part integration
•High flowability
• Panorama sunroof
frame
Shrinkage Comparison
CLTE Comparison
0.4
30 120
0.8
50 125
MD Shrinkage TD Shrinkage
AR-5300H
AR-5300H
Ref. (GF)
Ref. (GF)
MD Direction TD Direction
AR-5300HAR-5300H
μ/m
°C
22
Ref. (GF)
Ref. (GF)
23
High Heat Resistance LFTPP1330H
BENEFITS CHARACTERISTICS
APPLICATIONS
•High Heat Resistance
•High Flow
•Dimensional Stability
•Fan Shroud
•FEM
Tens
ile S
tren
gth(
mpa
)
High Heat Stability
120
130
140
PP-LGF High Heat
-12%
-5%
0 500hr 1,000hr
High Modulus (Nylon/GF grade material properties)
Tens
ile S
tren
gth(
mpa
) 4,000
3,000
2,000
1,000
040 70 100 130 160
Temp.()
PP-LGF*40(PP1340) PA66-SGF**30 PA6-SGF30
3D-Tow
3D tow insert injection technology for stiffener
3D Core built upon LOTTE Chemical’s
CFT (3D-Tow)
3D Core insert injection
High modulus & light-weight
stiffener solution
* CFT: Continuous Fiber reinforced thermoplastic Tape
* LGF: Long Glass Fiber ** SGF: Short Glass Fiber
24 25
Product Selection Guide
Segment Key Application Products
Properties
ASTM ISOPhysical Properties Mechanical Properties Mechanical Properties Physical Properties Mechanical Properties Thermal Properties Electric Properties
Specific Gravity
Melt Flow Index
Mold Shrinkage
Tensile Strength
Flexural Strength
Flexural Modulus
Izod Impact (Notched) Hardness Specific Gravity Melt Flow Index Tensile
StrengthFlexural Strength
Flexural Modulus
Charpy Impact Hardness VST
HDT (Unannealed)
VolumeResistivity
Test Method ASTM D-792 ASTM D-1238 ASTM D-955 ASTM D-638 ASTM D-790 ASTM D-790 ASTM D-256 ASTM D-785 ISO 1183 ISO 1133 ISO 527-1A ISO 178 ISO 178 ISO 179 1eA ISO 2039-2 ISO 306 ISO 75-2 LAM method
Test Condition
Natual Color
220/10kg 250/10kg* 250/5kg**
250/2.16kg*** 200/5kg****
-50mm/min 5mm/min*
30mm/min**
2.8mm/min 5mm/min*
10mm/min** 30mm/min***
2.8mm/min 5mm/min*
10mm/min** 30mm/min***
1/4'' 1/8''*
- Natual Color
220/10kg 250/10kg* 250/5kg**
250/2.16kg*** 200/5kg****
50mm/min 5mm/min*
30mm/min**
2mm/min 2.8mm/min*
2mm/min 2.8mm/min*
- -B/50 A/50*
B/120**
1.8MPa 0.45MPa* (120/hr)
Unit - g/10min % kgf/ [Mpa] kgf/ [Mpa] kgf/ [Mpa] kgf·cm/cm [J/m] R-Scale - g/10min MPa MPa MPa KJ/m2 R-Scale Ω•cm
Interior
I/P Part, Center Fascia
PC/ABS (High Impact)
HP-1000X 1.14 4.6*** 0.4-0.7 580 820** 22,000** 55 115 1.14 4.6*** 55 83 2,150 55 115 126
HP-1000XA 1.13 27* 0.4-0.7 550 750 20,500 45 113 1.13 27* 50 80 2,100 49 113 123
HP-1000XC 1.17 4*** 0.4-0.7 600 900** 23,500** 55 118 1.17 4*** 60 90 2,400 60 118 124
HP-1000XL 1.14 4.7*** 0.4-0.7 580 830** 22,500** 50 115 1.14 4.7*** 55 83 2,300 52 115 128
PC/PBT AE-3080C 1.19 15** 0.5-0.8 570 850* 22,000* 55 116 1.19 15** 55 88 2,100 60 116 126
Center ConsolePC/ABS (High Flow) WP-1069 1.13 47* 0.4-0.7 580 800 22,500 58* 113 1.13 47* 52 82 2,300 48 113 123
PC/ABS (Low Gloss) LH-1069 1.13 30* 0.4-0.7 520 700 20,000 65* 111 1.13 30* 47 75 2,100 52 112 121
Interior Part PC/ABS (Paint-free) LX-1098F 1.13 42* 0.4-0.7 550 790 22,000 40* 114 1.13 42* 55 90 2,500 41 114 120
Globe Box, Metal Back Molding PC/ABS/GFWP-1100 1.21 41* 0.2-0.5 920* 1200 43,000 8 1.21 41* 83* 135 4,300 11.5 131
WP-1200 1.27 36* 0.15-0.45 1200* 1500 62,000 8 1.27 36* 109* 180 7,400 11 130
Interior PartLow Gloss ABS SL-0100 1.03 7.5 0.4-0.7 330 450 16,000 6 97 1.03 7.5 35 57 1,800 11 93 97
Low Gloss ABS (High Heat) LH-0300 1.04 10 0.4-0.7 354* 465 17,593 10 100 1.04 10 36 58 2,060 16 100 100
Interior PartHigh Heat ABS (General Purpose)
SR-0300 1.05 13 0.4-0.7 450 620 23,000 23 110 1.05 13 48 76 2,500 23 110 102
SR-0310FM 1.06 20 0.4-0.7 400* 640 21,000 15 109 1.06 20 50 78 2,600 17 109 103
SR-0320 K 1.06 9 0.4-0.7 420* 650 22,000 17 110 1.06 9 48 76 2,450 15 110 106
SR-0320LI 1.05 6 0.4-0.7 400* 610 20,000 22 110 1.05 6 45 74 2,400 24 110 107
SR-0320LT 1.05 10 0.4-0.7 460* 700 23,800 17 113 1.05 10 50 80 2,500 18 113 106
SR-0325L 1.06 8 0.4-0.7 500 750** 24,000** 12 115 1.06 8 48 75 2,400 13 115 115
SR-0325LT 1.06 4 0.4-0.7 440* 620 21,000 12 113 1.06 4 50 85 2,500 15 113 113
SR-0330L 1.07 3.5 0.4-0.7 520 720** 24,000** 13 115 1.07 3.5 51 78 2,400 13 114 120
Interior PartPC/ASA (Low Gloss) WR-7250H 1.16 40* 0.4-0.6 600 850** 22,500** 35 118 1.16 40* 57 90 2,450 55 118 129
PC/ASA (EF) IF-7900 1.17 36* 0.4-0.6 550 800** 21,500** 20 114 1.17 36* 56 85 2,150 46 114 132
Interior PartDiffusion PC (General) TP-1020 1.19 30* 0.4-0.7 600* 920*** 23,000*** 65* 121 1.19 30* 59* 90 2,100 16 121 145
Diffusion PC (Light Blocking) TP-1020U 1.19 20(300°C, 1.2kg) 0.4-0.7 600* 920*** 23,000*** 78* 121 1.19 20(300°C, 1.2kg) 57* 90 2,130 64 122 147
Interior Part High Impact PC IV-1075C 1.19 7(300°C, 1.2kg) 0.5-0.8 620* 920*** 23,000*** 95* 121 1.19 7(300°C, 1.2kg) 59* 93 2,100 74 121 141
Instrument Panel LFT PP2320E 1.01±0.03 [65] [80**] [3,300**] [280] 1.01±0.03 64 90 3,600 29 151
Door Module Panel LFT
PP1320(E) 1.01±0.03 [90] [120**] [4,600**] [140] 1.01±0.03 90 130 4,800 14 150
PP1330(E) 1.10±0.03 [110] [160**] [6,600**] [175] 1.10±0.03 110 170 6,900 19 156
PP1320(LE) 1.01±0.03 [90] [118**] [4,500**] [135] 1.01±0.03 90 125 4,200 13 151
PP1330(LE) 1.10±0.03 [105] [155**] [6,000**] [170] 1.10±0.03 105 160 6,500 18 156
Over Head Console, Step Pad for truck LFT PP1340T 1.20±0.03 [132] [170**] [7,500**] [200] 1.20±0.03 135 180 8,000 27 161
Seat Back LFT PP2320F 1.01±0.03 [90] [115**] [4,800**] [170] 1.01±0.03 90 110 4,700 14 151
Exterior
Radiator Grille, Side Mirror Housing
ASA
WR-9300HF 1.07 12 0.4-0.7 450* 680 22,000 15* 106 1.07 12 44* 67 2,100 13 106 100
WR-9330I 1.07 5 0.4-0.7 480* 710 23,000 14* 107 1.07 5 52 80 2,400 10 108 104
A,B,C Pillar Trim WR-9120 J 1.07 26 0.4-0.7 450* 650 21,000 21* 105 1.07 26 43 72 2,260 14 105 98
Side Mirror Housing WX-9300UV 1.08 10 0.4-0.7 440 630 20,000 16* 104 1.08 10 47 70 2,250 12 104 96
Radiator Grille WX-9310UV 1.08 6 0.4-0.7 440* 680 22,000 18* 105 1.08 6 49 70 2,400 14 106 101
WX-9330UV 1.09 4 0.4-0.7 450* 640 21,000 22* 103 1.09 4 45* 73 2,300 13 103 103
Pillar, O/S MirrorASA/PMMA
WX-9950 1.12 6 0.4-0.7 500 700 20,000 7 108 1.12 6 46 68 2,100 107 96
Radiator Grille, Garnish WX-9950UV 1.16 6 0.4-0.7 640 780 23,000 4 118 1.16 5 65 90 2,600 118 102 77
Radiator Grille Metal Plating ABSMP-0160 R 1.04 17 0.3-0.6 480* 690 23,000 28 109 1.04 17 49 68 2,300 27 109 100
MP-0670 1.04 2.3**** 0.3-0.6 450* 660 21,500 24 108 1.04 2.3**** 51 72 2,350 25 108 98
Rear Spoiler ABS (Blow Molding) BM-0320J 1.04 6 0.3-0.6 432 585 18,441 26 101 1.04 6 42 63 2,157 30 101
Trunk Garnish Painting ABSPT-0180 H 1.04 2.3**** 0.3-0.6 380* 600 20,000 33 105 1.04 2.3**** 42 66 2,100 32 105 97
PT-0180C 1.04 15 0.4-0.7 380* 530 18,500 36 98 1.04 15 39 62 2,000 36 98
Radiator Grille, Wheel Cover Metal Plating PC/ABSWP-1041G 1.09 31* 0.4-0.7 500 670 19,500 55* 105 1.09 31* 47 70 2,000 47 107 113
WP-1051 1.1 25* 0.4-0.7 460 630** 17,800** 46 102 1.1 25* 45 62 1,750 46 99 115
WP-1061 1.12 16* 0.4-0.7 480 650 18,000 55* 100 1.12 16* 45 70 1,800 48 100 123
Wheel Cover PC/ABS WP-1059 1.12 45* 0.4-0.7 540 750 21,000 48* 112 1.12 45* 54 75 2,250 45 112 114
Door Handle, Door PanelPC/PBT
AE-3060 1.2 8*** 0.4-0.6 600 800 21,000 70* 114 1.2 8*** 60 80 2,100 65 114 124
Energy Absorber AE-3063I 1.2 45* 0.5-0.8 500 700 19,000 77* 110 1.2 45* 50 67 1,800 54 110 120
Radiator Grille PC/PET AE-2030 1.2 22(260°C/5kg) 0.5-0.8 570 780 21,000 72* 113 1.2 22(260°C/5kg) 54 80 2,200 65 115 131
Body Panel
PC/PET/MF
AE-2130 1.23 21(260°C/5kg) 0.4-0.7 570 810 24,000 54* 111 1.23 21(260°C/5kg) 56 82 2,200 30 111 132
Rear SpoilerAE-2150 1.33 43(260°C/5kg) 0.3-0.6 670 880 40,000 6* 110 1.33 43(260°C/5kg) 63 100 3,800 6 110 140
AE-2230 1.35 20(260°C/5kg) 0.3-0.6 590 780 40,000 7* 110 1.35 20(260°C/5kg) 55 90 3,900 7 110 135
Radiator Grille, Side Mirror Housing, Roof Rack
PC/ASAWR-7000 1.15 23* 0.4-0.7 590 770 21,000 30 110 1.15 23* 53 80 2,200 45 110 113
WX-7030 1.16 38* 0.4-0.7 600 850 22,500 45 110 1.16 38* 60 90 2,400 60 110 139*
Rear Spoiler PC/ABS/MF WP-1170M 1.28 12.5(260°C/5kg) 0.3-0.6 630 950 38,500 9* 112 1.28 12.5(260°C/5kg) 62 98 3,800 16 112 137
Back Beam LFT
PP3320B 1.01±0.03 [65] [80**] [3,300**] [280] 1.01±0.03 64 90 3,600 29 151
Stiffener PP1330ET 1.10±0.03 [105] [165**] [6,500**] [230] 1.10±0.03 105 165 6,400 22 156
Structure
Fender & Fuel Filler Door PA/PPE/CNT (High Heat) CA-7009 1.09 15(280°C/5kg) 1.0-2.0 600 800 21,500 20* 113 1.09 15(280°C/5kg) 57 80 2,000 113 190* 10^4
Panorama Sunroof Frame PBT/ASA/GF AR-5300H 1.45 30** 0.1-0.4 1,300* 1,900 90,000 9, 8* 117 1.45 30** 110 170 7,800 8 117 205 180, 195*
FEM CarrierLFT
PP1330HF 1.10±0.03 [112] [165**] [6,500**] [170] 1.10±0.03 108 168 6,800 18 158
PP1340HF 1.20±0.03 [132] [170**] [7,500**] [200] 1.20±0.03 135 180 8,000 25 161
Fan Shroud PP1330H 1.10±0.03 [108] [169**] [6,700**] [160] 1.10±0.03 108 168 6,600 18 156
Lighting
Head Lamp Bezel Metallization PBTASF-9810FM 1.31 60*** 1.5-1.8 550* 850* 26,500* 3.5, 3* 116 1.31 60*** 58 80 2,320 3.5 116 185 57, 160*
ASF-9860 1.31 74*** 1.5-1.8 570* 850* 26,500* 3.5, 3* 116 1.31 74*** 58 80 2,320 3.5 116 57, 175*
Head Lamp Bezel PCLT-1220 1.2 22(300°C, 1.2kg) 0.5-0.7 640 920 23,000 75* 120 1.2 22(300°C, 1.2kg) 64 92 2,300 60 120 145
LT-1100 1.2 11.5(300°C, 1.2kg) 0.5-0.7 640 920 23,000 87* 120 1.2 11.5(300°C, 1.2kg) 64 92 2,300 75 120 146
Rear Lamp Housing PC/ABS (High ImpactWP-1089 1.13 47* 0.4-0.7 540 770 21,500 60* 113 1.13 47* 52 80 2,200 51 113 126
HP-1000XG 1.15 37* 0.35-0.65 650 900 24,000 55* 120 1.15 37* 60 95 2,500 50 120 130
Rear Lamp Housing High Heat ASA WR-9370 1.07 3 0.4-0.7 500* 710 23,000 15* 106 1.07 3 49 70 2,160 13 106 109
26 27
At a Glance LOTTE Chemical’s technologies help to enrich our daily lives.
Basic/Intermediate Petrochemicals
Polymer
Monomer
High Performance Plastic Materials
Field of Business
Capacity
Basic Chemicals
Advanced Materials
SPECIALTY
ABS
PC
S-SBR
EPDM
EOA
MMA
Acrylic solid surface
PMMA
Natural quartz engineered stone
670
460
100
96
230
260
970k sheeets
110
320k sheeets
MONOMER
EG
SM
PX
OX
Me-X
PTA
PIA
1,830
577
750
210
160
1,100
460
BASIC CHEMICALS
EL
PL
BL
BZ
TL
XL
4,500
1,697
450
766
339
139
POLYMER
HDPE
LLDPE
LDPE/EVA
PP
PET
1,605
490
360
1820
520
* Advanced Materials
Sales & Production Sites
2224
Countries
Production bases
PRODUCTION PLANTAsia Malaysia, Indonesia, Uzbekistan, Pakistan,
South Korea*, China*, Vietnam*, India* (‘20. 4Q)
Europe Hungary*, Turkey* (E-stone)
America U.S, Mexico*
HQ / R&D – South Korea
HQ Seoul
R&D Uiwang, Daejeon
SALES CORPORATIONAsia China*, Thailand*, Japan*
Europe Germany*, Poland*
America/Africa U.S*, Nigeria
10,678
Employees Worldwide
Including major subsidiaries (Domestic & Overseas)
(Unit: KTA)
China
South KoreaUiwangYeosuGwangjuBusanGumiUlsan
ChinaSanghai
ShenzhenTianjin
SuzhouWeihai
Dongguan
GermanyFrankfurt
ThailandBangkok
USALos AngelesDetroit
JapanTokyo
IndonesiaJakarta
TurkeyIstanbul
HungaryKornye
ItalyMilano
MalaysiaKuala Lumpur
VietnamHanoi
MexicoTijuana
IndiaDelhi
Chennai
WarsawFrankfurt
Milano
Bratislava
IstanbulManisa
DelhiDubai
Bawal
Bangkok
Tokyo
Shenyang
Tianjin
Detroit
San DiegoLos Angeles
TijuanaAlabama
Jakarta
Kuala Lumpur
Hanoi Dong Nai
Suzhou
ShanghaiJiaxing
Hefei
Shenzhen
Weihai, Qingdao
Dongguan
Seoul, Uiwang, Yeosu, Gwangju, Busan, Gumi, Ulsan
South Korea
Frankfurt
MilanoKornye
Istanbul
Delhi
ChennaiBangkok
Tokyo
Tianjin
DetroitLos Angeles
Tijuana
Jakarta
Kuala Lumpur
Hanoi
SuzhouSanghai
Shenzhen
Weihai
Dongguan
South Korea
ChennaiMumbai
Global Network (Advanced Materials)
HQ
Sales Corporation
Production Plant
Sales & Production Coporation
Branch, Sales Office
SOUTH KOREA
Seoul (Headquarters)
Tel: +82-2-829-4114
Uiwang (Advanced Materials)
Tel: +82-31-596-3114
Yeosu Plant
Tel: +82-61-689-1220
Gwangju Service Office
Tel: +82-62-945-8846
Busan Service Office
Tel: +82-51-465-6829
Gumi Sales Office
Tel: +82-54-468-2811
Ulsan Sales Office
Tel: +82-52-267-9804
GLOBAL
Sales CorporationLos Angeles, U.S.A.Tel: +1-714-443-0945
Frankfurt, GermanyTel: +49-6196-7727-260
Warsaw, PolandTel: +48-506-760-890
Shanghai, ChinaTel: +86-21-6270-3000
Tokyo, JapanTel: +81-3-6369-6419
Bangkok, ThailandTel: +66-2-624-6726
Branch/Sales Office
ASIAShenzhen, ChinaTel: +86-755-8203-2323
Tianjin, ChinaTel: +86-22-2836-4258
Suzhou, ChinaTel: +86-512-6262-0323
Weihai, ChinaTel: +86-631-5666-812
Qingdao, ChinaTel: +86-532-8577-9681
Hanoi, VietnamTel: +84-243-227-2071
Dong Nai, VietnamTel: +84-251-351-4390
EUROPEMilano, ItalyTel: +39-02-64672-243
Istanbul, TurkeyTel: +90-212-437-8101(115)
Bratislava, SlovakiaTel: +421-220-375-114
MIDDLE EAST
Dubai, U.A.E.Tel: +971-4-245-1401
Production PlantTianjin, ChinaTel: +86-22-5868-291
Dongguan, ChinaTel: +86-769-8300-9852
Tatabanya, HungaryTel: +36-34-814-120
Tijuana, MexicoTel: +52-664-627-4947
Dong Nai, VietnamTel: +84-97-140-8940
Sales & Production Coporation
Alabama, U.S.A. Tel: +1-334-826-0094
Hefei, China Tel: +86-551-6530-2900
Jiaxing, China Tel: +86-573-8391-2281
Shenyang, China Tel: +86-24-6785-4228
Manisa, Turkey Tel: +90-236-213-03-43
Kuala Lumpur, MalaysiaTel: +60-3-2283-3714
Jakarta, IndonesiaTel: +62-21-250-5517
Chennai, IndiaTel: +91-44-4299-4255
Delhi, IndiaTel: +91-124-4153-804
Mumbai, IndiaTel: +91-22-6110-0177
AMERICADetroit, U.S.A.Tel: +1-248-509-7460
San Diego, U.S.A.Tel: +1-619-500-2837
Ethylene, Propylene, BD, SM, OX, C5
PE, PP, PET
EO/EG/GE, EOA, PIA/PTA/MMA
starex® Styrene & general product ABS, ABS Alloy, ASA, EPS, PP
INFINO® Engineering plastics PC, PC Alloy, PBT, mPPE, PA, PPA, PPS, PCT, TPE
Performance materials TPE, Modified adhesive resin, TPO, LFT, EPP
staron® Acrylic solid surface
Radianz® Natural quartz engineered stone
Locelain® Engineered porcelain surface
MEMBRIO
Construction
Materials
Water Treatment Membrane
Advanced Materials