Post on 09-Aug-2020
Important: Read all instructions prior to installation.
Wireless LED RGB Wall Switchfor EZ Dimmer Series Controllers
1 - 868MHz RGB LED Dimmer Wall Switch1 - 3V CR2032 Battery
Parts Included
Instructional SheetPart Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533 support@superbrightleds.com
Wall Switch
ControllerSafetySet-Up Instructions
Cove Lighting Application
Remote1. Follow illustrated steps to remove the Battery Tray. Insert the
3V battery included with the Wall Switch.Controller1. Make sure power to the Controller is disconnected.2. Using a small fl athead screwdriver, loosen the labeled
terminal screws visible on the top of the controller. 3. Matching light strip wires with labeled slots on the Controller,
insert wires and tighten terminal screws. Be sure wire conductor, not wire insulation, is secured in terminal.
4. Turn power on and wait until light strip illuminates. If it does not come on, check light strips and wiring connections.
• DO NOT install with power applied to controller.
• DO NOT expose the Wall Switch or Controller to moisture.
EZD-4C8A Controller
EZD-RGB-WM
EZD-RGB-WMController: EZD-4C8A
Power Supply Controller connected to multiple in-line LED strips
Wireless Signal to Controller
Push ON/OFF
Wall Switch
DC
INP
UT
OU
TPU
T
V+
V-
V+
R-
G-
B-
W
12/36VD
C
PairingSwitch
MASTER SLAVE
DC
INP
UT
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VD
C
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-RGB-WM Wall SwitchOperating Voltage 3 VDC
Battery Size CR2032Operating Frequency 868 MHz
FCC ID# 2ACUQ2836
Single PressTurns light on/off . If the receiver Controller Pairing Switch has been depressed, a single dial press on the Wall Switch pairs the Switch to the Controller.
Double Press Increases or decreases LED intensity until you release, turning LED on will remember the last memory position
Left/Right Movement During color mode, scrolls through RGB light strip colors. During dimming mode, controls LED intensity level
Hold Press Increases LEDs to maximum intensity
EZD-4C8A ControllerInput Voltage Current Output Wattage12~36 VDC 4 X 8A 384W(12V) 768W(24V)
1152W(36V)
Operating the Wall Switch/Controller1. Press “Pairing Switch” button on the Controller.
Immediately press the Wall Switch to pair it to the Controller. The LED lights wired to the Controller will blink when the pairing is complete.
2. Multiple Wall Switches can be paired to a Controller, and can be paired to multiple Controllers. If multiple Controllers paired to a Wall Switch are not in sync, unpair and then pair until Controllers and lights are in sync.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Wall Switch Instructions
2 - Mounting Screws
1. On/Off /RGB Color/Brightness Push DialPush dial for remotely activating/controlling RGB light strips.
2. Color Gradient Visual key representing the specifi c dial colors.
3. Dimming LevelVisual key representing the dial brightness level.
4. Pairing SwitchTo Pair Wall Switch to Controller, push once and then push Wall switch. Lights will blink once to indicate linking. To unpair Wall Switch(es), push and hold until lights blink twice.
5. Master/Slave JumperSet Jumper to Master for main Controller. Master emits syncronization signal to Slave Controllers. Set Jumper to Slave to receive syncronization signal from Master Controller. Use Master for the fi rst Controller in each zone. To acheive precise syncronization between Controllers in one zone, set additional Controllers to slave.
1. Pull off dial and collar from front plate.
2. Using a fl at head screwdriver, pry rear switch housing away from front plate.
3. Insert battery with tray into slot, matching the polarity on the battery with the slot labels.
4. Fasten wall switch using mounting screws.
5. Reinstall front plate, collar and dial.
1 2 3 4
Push ON/OFF
11
2
3
4
4
5
32
45
Important: Read all instructions prior to installation.
Instructional SheetPart Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533 support@superbrightleds.com
EZD-RGB-WMController: EZD-4C8A
Connection Diagram
Example Diagrams
DC
INP
UT
OU
TPU
T
V+
V-
V+
R-
G-
B-
W
12/36VD
C
PairingSwitch
MASTER SLAVE
DC
INP
UT
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VD
C
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
EZD-4C8A Controller
Common Anode Output (+)
Channel 2 Output (-)
Channel 1 Output (-)
Channel 3 Output (-)
(+)(-)
Channel 4 Output (-)
Pairing Switch
Master/Slave Jumper
B G R V+NC
To Additional Controllers24VDC OutFrom
PowerSupply
24VDC In
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-RGBNW300X4-24V
WBRG+
WBRG+
WBRG+
WBRG+
WBRG+
B G R V+
NFLS-RGB150X2-WHT-LC4
BRG+
BRG+
BRG+
BRG+
BRG+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-B300-WHT-LC2
NFLS-G300-WHT-LC2
NFLS-R300-WHT-LC2
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
B G R V+NC
To Additional Controllers24VDC OutFrom
PowerSupply
24VDC In
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-RGBNW300X4-24V
WBRG+
WBRG+
WBRG+
WBRG+
WBRG+
B G R V+
NFLS-RGB150X2-WHT-LC4
BRG+
BRG+
BRG+
BRG+
BRG+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-B300-WHT-LC2
NFLS-G300-WHT-LC2
NFLS-R300-WHT-LC2
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
B G R V+NC
To Additional Controllers24VDC OutFrom
PowerSupply
24VDC In
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-RGBNW300X4-24V
WBRG+
WBRG+
WBRG+
WBRG+
WBRG+
B G R V+
NFLS-RGB150X2-WHT-LC4
BRG+
BRG+
BRG+
BRG+
BRG+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
To Additional Controllers12VDC OutFrom
PowerSupply
12VDC In
NFLS-B300-WHT-LC2
NFLS-G300-WHT-LC2
NFLS-R300-WHT-LC2
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
_+
DC
INPU
T
OU
TPU
T
V+
V-
V+
CH1
CH2
CH3
CH4
12/36VDC
PairingSwitch
MASTER SLAVE
EZD-4C8A PRI:Uin=12-36VDClin=8.3ASEC:Uout=1x(12-36)VDCIout=4x8APout=1x(96-288)WTEMP RANGE: -20ºC-+50ºC
Easy Dimmer Series
(1) RGB 24VDC Application / EZD-4C8A (2) RGB 12VDC Application / EZD-4C8A
(3) Seperate RGB 12VDC Application / EZD-4C8A
Power In
Wireless LED RGB Wall Switchfor EZ Dimmer Series Controllers
Note: CH1 is the Red Channel CH2 is the Green Channel CH3 is the Blue Channel CH4 is not used