Post on 10-Jan-2017
1
Television Broadcasting System
KAUSIK DAS.(ET12BT0215)
Student at Kaziranga University
SUBMITTED BY:
2
Contents IntroductionTypes of StudiosProduction Control RoomProduction areaEditingMaster Switching RoomEarth StationTransmitterOutside broadcasting
3
Introduction• Part of the DD India• The largest television network in the world.• Power of 10KW covering range of 89-120 kms.• Better facilities for recording and transmission .• Separate studio for recording of north-east program.• Computerized earth station for networking.• Earth station is utilized for up-linking the Guwahati
Doordarshan program to entire country through INSAT-4B.
4
STUDIO
5
1) MAIN STUDIO• Dimension of 22x16.5 metres. • Fully digitalized with four cameras setup.• Equipped with different lights and microphones.• Mainly used for all major recordings.• Acoustic treatment.
6
Three main lights:• Key Light: It is hard light about 1KW of power. Used
as main source of power.• Fill Light: It’s cool light about 500W, used to remove
object formed due to key light.• Back Light: It’s hard light used to remove the back
shadow and separate the object form background which gives a 3D picture.
[Ratio 3:2:1 for monochrome and 3:2:2 for color]
7
Microphone
8
Classification on construction basis:
Carbon Microphone Crystal Microphone
2)1)
9
Ribbon Microphone
3)
Condenser Microphone
4)
Dynamic microphone
5)
10
Main Studio
11
Studio camera:• Lens Block• CCD Block• Electronic Block
*CCD and EB are collectively known as camera head.All the captured signals are transferred to and from the base station using a multiple core-Triax cable.
12
2) CB STUDIO:
• Dimension of 9.2x6 metres. • Fully digitalized with two cameras setup• Progams include discusion or anchoring are generated• Teleprompter.
13
CB Studio
Production control Room(PCR)
1
?
15
• Activities in this area are:- Minor editing. Direction to the production crew by the producer. Management of feed during a live program. Monitoring of output/off air signal.
Production Control Room
16
Production Control Room of DDK-Guwahati
17
Components of PCRPCR is house with :
1) Vision Mixer.2) Audio Mixer.3) Camera Control Unit(CCU).4) Character Generator .5) Tape Recorder.
Vision Mixer(video mixer)
Audio Mixer(Mixing desk)
18
Camera control unit(CCU) :
This unit includes :1) Focus.2) Zoom-in/out.3) Beam focus.4) Contrast.5) Brightness.
A color composite video signal(CCVS) isReceived from the studio camera through the Triax -able can be viewed in monitor.
Character Generator (CG):
Modern CG are computer based and charactercan be generated with the help of software.
Character may be static or animated (ex: news crawls and credits roles)
19
Video tape recorder :
It contain :1) Analog and digital processor servo system.
2) Microprocessor.
3) Memory etc.
Here a video tape recorder(VTR) or Video Cassette recorder (VCR) used for recording.
Recording is done in playback format.
Audio and video level can be adjust fromhere.
Quality of the recorded program are tested Immediately after recording and error is solved for better quality.
20
PRODUCTION AREA
21
Production Area:• Area where the actual production decision is made and the show
is created. This area includes the space for the director, producer and their assistants. One of the most significant parts of the production area is the monitor wall. It includes the following:
• Preview monitor• Live or on-air monitor• Camera monitors• VTR monitors• Graphics monitors• Still stores monitors• Routed monitors
22
Advantages of large programmable monitors:
• Compact• Light• Consume little power
Audio Area:It includes:• Audio mixing board• Patch panels• Video and audio monitors
23Audio Control
24
EDITING
25
EDITING
Two types of Editing:-
1) LINEAR EDITING(non-computerized)2) NON-LINEAR EDITING(computerized)
26
LINEAR EDITING
It is basically a mechanical process that employs the use to perform the edit functions are:- • Camcorders• VCRs • Edit controllers and• Mixers
27
This editing technique is performs in linear steps, one cut at a time (or a series of program cuts) to its conclusion. It is the process of assembling footage in a sequential fashion, from start to finish. This type of editing is generally carried out when working with video tapes. Video tapes can be cut into sections and spliced together. The content must be accessed sequentially.
CAMCORDERS VCRs
Video tapes
28
NON-LINEAR EDITING: Carried out on a computer with editing software. Gathering into the software, then cut, copy and paste it together in desired order. When the nonlinear sequence is ready, it is recorded onto the master tape. Possible to access any frame.
Non-Linear Editing
29
Some of the editing software available and used in DDK, Guwahati are:
Leitch- velocity DPS & Velocity HD (version 8 and 9).
Adobe Premiere pro CS-3 and CS-6.
Canopus-EDIUS-4.
ADVANTAGE OF NON-LINEAR EDITING The original source files are not lost or modified during editing. & one of the biggest adv. Compared to linear editing.
30
MASTER SWITCHING ROOM
31
Master Switching Room(MSR) It is used for transmission media. Room where all different sources from the outside studio comes here and enroots transmission to different destination like Tr & Earth station. Room comprises of routine switcher, video/audio distributor amplifier etc. So, it is called heart of the studio. Most of the switching electronics is kept here:-1. Camera base stations.2. Switcher main frame. 3. Sync pulse generator(SPG).4. Satellite Receivers etc. Signals is routed through MSR from various
to earth stations and can be monitored at various stages.
32
EARTH STATION
33
Earth Station
GROUND STATIONS
34
It is the terrestrial base of the system.Located either on the surface of the earth, or within Earth’s atmosphere.Communicates with the satellite (or spacecraft) by transmitting and receiving radio waves.Successful transmission of radio waves to a spacecraft (or vice versa), lead to establishment of telecommunication link. It is possible for a satellite to communicate with more than one Earth station at a time.
EARTH STATION
35
WHAT IS AN EARTH STATION?
UPLINK STATIONRECEIVE CENTRE
DOWNLINK FREQ: 6725MHzUPLINK FREQ: 6333MHz
36
Earth station involves the two terms which are basically the important parameters of the communication i.e., UPLINK & DOWNLINK.
1. Uplink:The process of gathering any information part & sending it to the satellite, running on specified frequency is termed as UPLINK. The uplink frequency is 6333MHz.
2. Downlink:The process by which satellite sends or received the signals to the controlling stations is termed as DOWNLINK. The downlink frequency is 3725MHz.
37
Major Components of Digital Earth Stations Some Major components are:- PDA(Parabolic Dish Antenna) Up converter Modulator Encoder IRD(Integrated Receiver Decoder)
38
TRANSMITTER
39
TRANSMITTER
• In DDK-Guwahati VHF Solid State NEC(Japan) TV transmitter is used.
• It is a digital transmitter.• Power rating is 10kw.• Main parts are:
o ExciteroAmplifier
TV TOWER(200M)
40
EARTHSTATION
TANSMITTER/RECEIVER
SATELLITE
DTHRECEIVER
TV
UPLINKINGDOWNLINKING
THE PROCESS OF TRANSMISSION
41
Picture IF : 38.9 MHzSound IF : 33.4 MHz
Uplink : 6333 MHzDownlink : 6725 MHz
42
OUTSIDE BROADCASTINGThis is shooting progrms outside the studios. It can be live or recorded programs. It involves two systems: OB van and ENG.
OB Van• Mobile unit • Mobile television control room• Equipped with a video switcher, intercom, graphics, audio, recorder/playback
decks and all the engineering equipment required to maintain a quality signal• Variety of sizes • Primary areas of OB van are:
o Production Areao Audio Areao Video Control/Transmission
43OB Van
44
Thank You