Post on 28-Jan-2022
TECHNICAL SPECIFICATION DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS
FOR DENTAL MOBILE VAN Name of Project
Instructions: Bidders must state in the column under Statement of Compliance the word either “Comply” or “Not Comply” against each of the individual parameters of each Specification stating the corresponding performance parameter of the equipment offered. Statements of “Comply” must be supported by evidence in a Bidders Bid and cross-referenced to that evidence. Evidence shall be in the form of manufacturer’s un-amended sales literature, unconditional statements of specification and compliance issued by the manufacturer, samples, independent test data etc., as appropriate. A statement that is not supported by evidence or is subsequently found to be contradicted by the evidence presented will render the Bid under evaluation liable for rejection. A statement either in the Bidders statement of compliance or the supporting evidence that is found to be false either during Bid evaluation, post-qualification or the execution of the Contract may be regarded as fraudulent and render the Bidder or supplier liable for prosecution subject to the provisions of ITB Clause 3.1(a)(ii) and/or GCC Clause 2.1(a)(ii). Bidder may submit offer which provides for superior specifications and /or better terms and conditions to the government at no extra cost. However, these shall not be given any bonus, credit or premium in the bid evaluation
Prepared by Technical Working Group
Republic of the Philippines Department of Health Regional Office No. XI
SOUTHERN PHILIPPINES MEDICAL CENTER J.P. Laurel Avenue, Davao City
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
General Description
The supplier shall supply, install and commission one (1) Digital X-ray Machine into the Dental Bus of the hospital
The X-ray machine can be operated using the
power supply of the Dental Bus provided by its generator.
The x-ray system must be provided with vertical
cassette holder with stationary grid of high ratio and not showing any grid lines.
The digital radiography system must be Picture Archiving Communication System- (PACS) ready and able to retrieve and send imaging studies to the SPMC PACS through wireless and wired LAN. It can also be integrated with the RIS of the hospital. The machine can store images in Dicom format It should have a system and monitor screen that
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
allows the operator to log into the software and displays the patient work list.
The machine shall be provided with technique selector and digital display for KV, mA and or mAs, exposure time and microprocessor controlled anatomical programming function keys
The system must be capable of integrating with the existing PACS/RIS at no extra cost.
The machine provided with ID barcode reader
The X-Ray Generator of the machine shall have the following capability:
High frequency inverter type generator • Maximum KV setting up to 125kVp or higher
Maximum tube current of 250 mA or higher
mAs setting up to 100 mAs or higher
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
maximum power of not more than 20KW The X-ray Tube must be of the following specification Dual focus or Single Focus Effective focus size not more than 1.2mm
Maximum Anode Heat Capacity not less than
140kHU
The X-ray Tube Support must have the following
specification:
With electromagnetic locking system
Vertical movement 770 – 1670mm or higher
Crosswise movement of X-ray focus 235mm or
higher
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
The x-ray tube support or tube stand shall be
installed in the dental bus in such a way that
upright x-ray examination can be performed.
The X-ray system must be have a Digital Acquisition
Workstation with the following features:
With latest 7th generation Intel i-Core Processor
with Windows 10 operating software.
Minimum of 8 GB RAM, minimum of 1.0TB HDD. 21 inch or bigger Medical Grade LED/LCD Monitor. Supported by all necessary software for all various Digital Radiography functions. Provision for all accessories like mouse, keyboard, power cable. Dicom support such as Print Management (SCU),
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
Storage(SCU), Modality Worklist
Management, Modality Performed Procedure Step, Grey Scale Standard Display Function (print out), and Networking capability with RIS/HIS/PACS. The machine shall be provided with its latest technology of wireless flat panel detector that made up of Cesium Iodide as its capture element or scintillator. The active pixel dimensions of the flat panel
detector should not more than 140 um The cassette/s or detector/s provided shall be 14”
X 17” Wireless FPD with at least 7.5 million pixels.
Grayscale 14 bits or better. Image acquisition time
3sec or less
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
The detector complies with IPX3 standard
Provided with detachable battery and charger if necessary. Capable of the following administrative system
Can create/modify user log-on and password and generate reports of user and patient logs
Can create/modify output printer configurations Can manage image output queue Can re-send image output Can manage local database [view/delete patient
image files] Can protect selected patient/image files from
reclamation Can create/modify technologist comments
The Imaging Processing Software
. Can process image to increase latitude while preserving detail contrast in both over-
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
penetrated and under-penetrated areas. Can process and deliver diagnostic quality images to PACS .
Contain independent controls within the user interface for the user for image adjustments
Have means to minimize the noise in areas of low-exposure to capture high-quality diagnostic details
The system have means to reduce radiation dose while retaining good image quality Can define area of interest automatically, and allow manual selection of complex anatomical structures Can facilitate automatic transfer of patient and procedure data to hospital HIS/RIS system. ) It must be DMWL (DICOM modality worklist) compliant to access patient and study data from HIS or RIS.
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
Other Terms and Conditions
It must have post processing features viz. geometric corrections, window level algorithms, annotation like markers, predefined text, drawing lines and geometrical shapes, multi-scale image processing, measuring distance and angles, shuttering, histograms, zoom, grey scale reversal, edge enhancement, noise reduction, indication of gray scale saturation level, latitude reduction. The supplier shall provide the following Radiation Protection devices and accessories such as:
a) One (1) set of contact gonadal shield b) One pc of upright gonad shield
c) Two (2) full body lead aprons d) One (1) pair of lead gloves e) One (1) Caliper The dental bus shall be provided by the supplier with adequate radiation shielding from transmitted
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
and scattered radiation. The walls and windows of the x-ray facility shall be lined with lead of at least 1.5 mm thick. The radiologic technologist must be provided with protective barrier lined with 1.5 mm thick lead with a lead glass Warranty for 2 years stating free repair services and replacement of parts or units within the period. The supplier, if given the award, shall submit a duly notarized preventive maintenance schedule upon delivery of the equipment. Must provide operation and instruction manuals with parts listings, tube rating chart and anode cooling chart.
Supplier must provide orientation training for users and maintenance personnel of the hospital.
The supplier shall assist the hospital management in
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
ensuring that the site intended for the ceiling mounted x-ray machines will be in accordance with the manufacturer’s standard requirements.
The supplier shall be responsible in providing the necessary equipment and/or devices needed for moving-in of the x-ray machines into the project site, if necessary. All cost associated with connectivity of the system to hospital PACS and HIS/RIS is the responsibility of the supplier
The manufacturer of the equipment being offered must conform with international safety and or quality standard as proven by the following certificates of conformance: a) IEC 60601 Medical Electrical Equipment b)ISO for Medical Equipment Quality
Management System and ISO Quality Management System, or US FDA Approved.
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
The brand of the equipment being offered by the supplier must be in existence in the Philippine market carrying the x-ray machine for at least ten years.
The supplier shall provide a certificate of Dicom Conformance for the x-ray machines. The supplier or its principal can provide trained
service personnel/s for preventive and corrective maintenance of the x-ray machines.
The supplier shall provide a certificate of Dicom
Conformance for its digital system The supplier must be the exclusive or authorized
distributor of the principal company of the equipment and the necessary consumables in the Philippines.
The supplier must have a technical support from its
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
principal by providing Service Engineer or Technical personnel to the supplier of its equipment
The factory trained Service Engineers employed by
the supplier or its Principal should be based in Davao City for preventive and corrective maintenance of the x-ray machines during the warranty period.
The service personnel referred in its bid must be the employee of the supplier or its principal for the past three (3) years has experience in maintaining a digital radiography x-ray system for the same length of time. It can be proven by submission of its training certificates, record of employment and SSS remittances for three years. It must be submitted together with its proposed technical specification as part of its technical bid.
TECHNICAL SPECIFICATION
DIGITAL RADIOGRAPHY X-RAY IMAGING SYSTEMS FOR DENTAL MOBILE VAN
Name of Project The bidder is required to complete its Statement of Compliance demonstrating how its items complied with the specification. Non- completion of Statement of Compliance for the item included in its bid shall be considered non- responsive for that item.
Item Procuring Entity’s Specification Bidder’s Specification as
Technical Offer
Statement of
Compliance
________________________________________
Name and Signature of Authorized Representative
e. It can respond within 24-48hrs should the existing equipment breaks down. In case of machine downtime, the supplier is given 3 days to do remedial action (repair). On the 4th day, if the unit is not operational, a penalty shall be imposed in accordance with the General Condition of the Contract of the bidding document. The equipment / machine must be able to comply with its installation and operation qualification which would be conducted in the presence of SPMC Biomedical Technician, End-user and the Company Engineer.
The bidder may submit offer which provides for superior specification and/or better terms and conditions to the government. However, these shall not be given any bonus, credit or premium in the bid evaluation.