Post on 11-May-2015
description
Group Member ASIM ASHFAQ BSME-01113024
SUPER PLASTIC FORMING
EXPLOSIVE FORMING
SUPER PLASTIC FORMING
INTRODUCTION Super plastic Forming is a metalworking process for
forming sheet metal. It works upon the theory of super plasticity, which means that ” capability that some materials have to undergo large uniform elongation prior to necking and fracture tension”. Super plastic forming (SPF) of sheet metal has been used to produce very complex shapes and integrated structures that are often lighter and stronger than the assemblies they have to replace.
Titanium alloys and alloys of zinc-aluminum; when heated , they can elongate to many times their original length.
Some other materials which shows “superplasticity” are:1. Titanium alloys2. Aluminum alloys3. Bismuth-tin alloys4. Zinc-aluminum alloys5. Stainless steel6. Aluminum-lithium alloys
CONSTRUCTION
• PROCESS• The process typically conducted at high temperature and under
controlled strain rate, can give a ten-fold increase in elongation compared to conventional room temperature processes. Components are formed by applying gas pressure between one or more sheets and a die surface, causing the sheets to stretch and fill the die cavity. Specific alloys of titanium, stainless steel, and aluminum are commercially available with the fine-grained microstructure and strain rate sensitivity of flow stress that are necessary for Super plastic deformation.
• SPF can produce parts that are impossible to form using conventional techniques. During the SPF process, the material is heated to the SPF temperature within a sealed die. Inert gas pressure is then applied, at a controlled rate forcing the material to take the shape of the die pattern. Super plastic alloys can be stretched at higher temperatures by several times of their initial length without breaking.
EXAMPLES Construction of fuel Tanks
Muddy Guards of Motorcars
ADVANTAGES• The finished product has excellent precision and a fine
surface finish.• Products can also be made larger to eliminate
assemblies or reduce weight, which is critical in aerospace applications.
• Lower strength required and less tooling costs.
LIMITATIONS• The biggest disadvantage is its slow forming rate.• Materials must not be superplastic at Lower
temperatures.• It is usually used on lower volume products.
APPLICATION IN PAKISTANCompany: Super Plastic Doors & WindowsAddress: Suit #11,1st Floor, Fareed Plaza, 65 Shadman Market, Lahore, Punjab, Pakistan
EXPLOSIVE FORMING
DEFINITION
“Shaping metal parts in dies by using an explosive charge to generate forming pressure.”
OR“The shaping or modifying of metals by means of
explosions.”
VARIOUS TECHNIQUESExplosive Forming Operations can be divided into
two groups, depending on the position of the explosive charge relative to the work piece.
1. Stand Off Method2. Contact Method
STAND OFF MATHOD
In this method metal plate is placed over a die, with the intervening space evacuated by a vacuum pump, then whole assembly is placed underwater and explosive material is placed at an appropriate height above the plate. For complicated shapes, a segmented die can be used.
intervene: become involved
CONTACT MATHOD
In this method, the explosive charge is held in direct contact with the work piece while the detonation is initiated. The detonation produces interface pressures on the surface of the metal up to several million psi.
PROCESSThe rapid change in explosive in to gas produce a
shock wave. The pressure of this shock wave is sufficient to form metal sheet.
The peak pressure , p , due to explosion, generated in water, is given by expression
p = k(((w)^1/2)/R)^a
Where P is in psi. K is the constant depends on the type of explosive. W is the weight of Explosive in pounds. R is the distance of explosive from the work piece and a is the constant.
EXAMPLE
OTHER EXAMPLES
Rocket engine nozzle Space shuttle skin
ADVANTAGESo It can simulate a variety of other conventional metal
forming techniques such as stamp- or press-forming and spin-forming in a single operation.
o Explosive hydro-forming can efficiently form large parts – up to 4’ square or 10’ in diameter.
o It is particularly suitable for short production runs of a large parts such as occurs in aerospace applications.
o It Maintains precise tolerances and Eliminates costly welds.
DISADVANTAGES1. Low tooling costs, but high labor cost. 2. Suitable for low-quantity production.3. Due to shock waves and spillage of water it is not
suitable to carry out indoor.4. It should be done in open air.
COMPARISON
EXPLOSIVE FORMING• In Explosive forming an
explosive charge is used instead of a punch or press.
• It can be use for large size of metal sheets.
• No preheating required before the explosive forming
• Less production cost.• Any product size, shape and
sheet thickness is possible.
SUPERPLASTIC FORMING• In super plastic forming
punch or press is used to form metal sheet forming.
• It can be only used for limited die design.
• High production cost.• It can be used for definite
shape, size and sheet thickness .