Post on 04-Jun-2018
8/13/2019 Suitcase BoomBox
1/65
Suitcase BoomBox
8/13/2019 Suitcase BoomBox
2/65
8/13/2019 Suitcase BoomBox
3/65
The Suitcase Boombox is a vintage suitcase converted into a boombox, complete with two
subwoofers and four tweeters. The whole system is powered by two lead acid batteries
hooked up to a charge controller, so the boombox can be charged via an AC/DC power supply
or even a solar panel. The mini amplifier delivers 25 watts of power per channel, giving the
system a lot of volume, comparable to a car audio system. You could definitely take this out tothe park and start your own mini dance party or use it to play loud music in your room. What I
love most about this project is that no two suitcase boomboxes will ever look the same.
Depending on the type of suitcase you use and the size and configuration of your speaker
setup, there is plenty of room to apply your own personal style to the project and make
something truly unique.
Parts List:
(1x) Vintage Suitcase (I found mine on Etsy)
(2x) 12V/4Ah Sealed Lead Acid Battery Radioshack 55034004
(1x) Pioneer TS-D1720C 6.75" Component Speaker Package Radioshack 55032192
(1x) Pioneer TS-D1720C 5.25" Component Speaker Package Radioshack 55032190 (I ended up
only using the tweeters from this package and saving the 5.25" speakers for another project.
You can also replace this part with any other 4Ohm tweeter.)
(1x) Sunforce 30-Amp Digital Charge Controller Radioshack 277-110
(1x) Topping TP20-MK2 MKII TA2020 Class T-AMP Digital Stereo Amplifier Amazon
(1x) 3-Ft. 1/8" Stereo to Dual Phono (RCA) Plug Y-cable Radioshack 42-494
(1x) 1/8" Stereo In-Line Audio Jack Radioshack 274-274
(1x) 1/8" Stereo Panel-Mount Audio Jack Radioshack 274-249
(1x) 3-Ft. 1/8" Stereo Plug Cable Radioshack 42-223
(1x) 50-Ft. 16-Gauge Clear 2-Conductor Speaker Wire Radioshack 278-1267 (you will only need
about 15ft)
(1x) 22 Gauge stranded wire, multiple colors Radioshack 278-1224
(1x) black electrical tape Radioshack 64-2373
8/13/2019 Suitcase BoomBox
4/65
(1x) Size M Panel-mount Coaxial DC Power Jack Radioshack 274-1563
(1x) AC-DC 12V 1.5A Power Supply Radioshack 273-316
(1x) M type plug Radioshack 273-344
(1x) 3/16" battery terminal connectors Radioshack 64-3132
Additional Materials/Tools:
Wire Cutters/Strippers Radioshack 64-224
Rosin Core Solder Radioshack 64-009
Soldering Iron Radioshack 55027897
Razor Blade Cutting Tool (for cutting leather suitcase)
Power Drill
Dremel
Screws (be sure to get some that match the hardware on your suitcase)
Locknuts/nylon nuts (for areas of high vibration) and regular nuts
Small L-Brackets
Screwdriver
1/4" plywood - I needed this to add some structural support to my suitcase, if you use a hard
clamshell case, you may not require any additional support.
scrap wood (for mounting charge controller)
marking pen
metal file
wire crimper Radioshack 64-225
Step 1: Layout speakers
8/13/2019 Suitcase BoomBox
5/65
This step will vary from suitcase to suitcase. My suitcase was 20" wide and 11" tall, this was
enough space to mount two 6.75" subwoofers and four 1.75" tweeters. I cut out paper to help
visualize the layout of the speakers on the side of the case. Eventually I settled on a symmetric
layout, with the two subs in the bottom center, and the tweeters along the upper corners.
Step 2: Clean out suitcase
8/13/2019 Suitcase BoomBox
6/65
8/13/2019 Suitcase BoomBox
7/65
You'll want to clear out a lot of room to mount all your components to the inside of the
suitcase. Use a razor blade to cut out any excess material (cushions, fabric dividers) and
remove any extraneous hardware (clips, brackets) with a screwdriver.
Save these scraps, you might use them later in the project (I used them to make a pocket for
holding my iPod).
Step 3: Cut out suitcase lining
8/13/2019 Suitcase BoomBox
8/65
8/13/2019 Suitcase BoomBox
9/65
8/13/2019 Suitcase BoomBox
10/65
I used a blade again to cut out the lining of the suitcase, on the side where I planned on
mounting my speakers. I also cut out some warped, plastic corner pieces that were sticking up.
Step 4: Install structural supports (if necessary)
8/13/2019 Suitcase BoomBox
11/65
8/13/2019 Suitcase BoomBox
12/65
The walls of my suitcase are made of leather with a fabric lining, on their own they will not be
able to support the weight of 2 subs and 4 tweeters. I cut out a piece of 1/4" plywood so that it
could fit snugly against the wall of my suitcase and provide extra support. I used a laser cutter
to cut out the speaker mounting holes (pdf of cutlines attached below), these cuts could also becut with a jigsaw or Coping saw. I kept the tolerance of my support structure tight, so it
essentially press fit up against the suitcase wall.
Step 5: Trace cutlines on suitcase
8/13/2019 Suitcase BoomBox
13/65
8/13/2019 Suitcase BoomBox
14/65
8/13/2019 Suitcase BoomBox
15/65
I used my structural support as a guide to trace cutlines onto the inside surface of the suitcase
with a pen.
Step 6: Cut holes in suitcase wall
8/13/2019 Suitcase BoomBox
16/65
8/13/2019 Suitcase BoomBox
17/65
Carefully cut along the traces and create holes for mounting your speakers. I was able to get
away with using a razor blade cutter to get through the leather sides of my case. If a razor
blade cutter is not enough to get through your suitcase, a jigsaw or Coping saw will probably dothe trick.
Again, save these leather scraps, you might use them later in the project.
Step 7: Remove front panel from subwoofers
8/13/2019 Suitcase BoomBox
18/65
8/13/2019 Suitcase BoomBox
19/65
8/13/2019 Suitcase BoomBox
20/65
Step 8: Mount subwoofers
8/13/2019 Suitcase BoomBox
21/65
8/13/2019 Suitcase BoomBox
22/65
The Pioneer kit comes with hardware for mounting the speaker components. Use the eight
longest screws in the kit to mount the two subs to the front of the suitcase. Use a nylon nut to
secure to back end of the screws and prevent vibrational loosening. You might also considering
finding a screw with a matching locknut. File down the pointy edge of the screw so you don't
accidentally scratch yourself.
Step 9: Mount tweeters
8/13/2019 Suitcase BoomBox
23/65
8/13/2019 Suitcase BoomBox
24/65
I cut my backing wood panel with such a tight tolerance that the tweeters press fit into the side
of the suitcase enclosure. For added stability, I used the metal inserts and screws from the
pioneer kit to hold the tweeters in place from the inside of the suitcase (though this is not their
intended purpose, it worked really nicely for me). Depending on your setup, you might also
consider using some of the kit's other mounting options.
Step 10: Remove lining of back panel and reinforce with wood
8/13/2019 Suitcase BoomBox
25/65
As with the front panel, use a blade to clear out any loose material attached to the back panel.
Step 11: Layout remaining components
8/13/2019 Suitcase BoomBox
26/65
8/13/2019 Suitcase BoomBox
27/65
8/13/2019 Suitcase BoomBox
28/65
Organize the remaining components around the back panel and mark drill holes. I used two
pieces of 2' wood scrap to prop up my charge controller above the surface of the plywood
support. Make sure the case will close before you finalize your layout!
Step 12: Passive crossovers
The Pioneer kit comes with passive crossovers to split up each channel of audio from the
amplifier into a signal for the sub and a signal for the tweeters. Use screws to mount both
crossovers onto the side of the suitcase, opposite from the speakers. Note - nearly all of my
screws were screwed through the 1/4 plywood backer, but not through the suitcase enclose.
Step 13: Wire crossovers to amplifier
8/13/2019 Suitcase BoomBox
29/65
8/13/2019 Suitcase BoomBox
30/65
Cut and strip a 2-3' piece of speaker wire (long enough so you can easily open the suitcase
without putting tension on the wire) and use it to connect one crossover to the amp's left
output and other to the right output. Be sure to connect the + crossover input to the +
amplifier output.
Step 14: Wire woofers to crossover
8/13/2019 Suitcase BoomBox
31/65
8/13/2019 Suitcase BoomBox
32/65
Strip two 2-3' pieces of speaker wire and solder the ends of one wire on each of the subwoofer
terminals. Connect the other end to the screw terminals labelled "subwoofer" on that
channel's corresponding crossover. Make sure that you connect the + crossover output to the +
speaker terminal.
Step 15: Wire tweeters to crossover
8/13/2019 Suitcase BoomBox
33/65
8/13/2019 Suitcase BoomBox
34/65
Since the two tweeters have a resistance of 4Ohm, I wired them in series to the tweeter output
from the crossover. To do this, connect one tweeter's + lead to the + crossover terminal (you
may need to lengthen the wire). Then connect the - lead of second tweeter (of the same
channel) to the - crossover terminal. Connect the remaining two leads from the tweeters to
each other to wire them in series. Repeat this for the second channel.
Step 16: Secure batteries
8/13/2019 Suitcase BoomBox
35/65
8/13/2019 Suitcase BoomBox
36/65
8/13/2019 Suitcase BoomBox
37/65
Use small L brackets to secure the two batteries against the lower corners of the suitcase.
Step 17: Prepare amplifier power cable
8/13/2019 Suitcase BoomBox
38/65
8/13/2019 Suitcase BoomBox
39/65
Cut the power supply that came with the amplifier and strip the wire. The outside lead is - and
8/13/2019 Suitcase BoomBox
40/65
the inside lead is +. Connect the exposed leads to a piece of 1-2' speaker wire and cover the
connection with electrical tape. This wire will connect the amplifier to the charge controller.
Step 18: Prepare battery terminal clips
Cut two more pieces of 1-2' speaker wire and crimp a 3/16" quick disconnect connector on one
end of each wire. These wires will connect the batteries to the charge controller.
Step 19: Connections to charge controller "battery" terminals
8/13/2019 Suitcase BoomBox
41/65
8/13/2019 Suitcase BoomBox
42/65
8/13/2019 Suitcase BoomBox
43/65
Connect the + end of the two battery connections from the last step, and the amplifier power
supply wire and crimp with one of the terminals included with the charge controller. Do the
same for the - leads of these three wires. Screw the terminal connections to the + and -
terminals of the charge controller, on the side labelled "battery".
Step 20: Wire charge controller to batteries
8/13/2019 Suitcase BoomBox
44/65
Connect the quick disconnects from the charge controller to the batteries. Make sure to
connect the + from the charge controller to the + on the battery (and vice versa).
Step 21: Prepare external power supply cable
8/13/2019 Suitcase BoomBox
45/65
8/13/2019 Suitcase BoomBox
46/65
Cut a 1-2' piece of speaker wire and attach an M-type barrel plug to one end. Crimp the
remaining two terminal mounts from the charge controller to the other end of the wire. Then
screw the terminals onto the side of the charge controller labelled "array".
Step 22: Mount charge controller
8/13/2019 Suitcase BoomBox
47/65
8/13/2019 Suitcase BoomBox
48/65
Now that all the connections to the charge controller have been made, use wood glue and a
screw to mount two pieces of 2" wood block to the plywood panel. Once the wood glue is dry,
use screws to attach the charge controller to the front of these blocks.
Step 23: Remove amplifier front panel
8/13/2019 Suitcase BoomBox
49/65
8/13/2019 Suitcase BoomBox
50/65
8/13/2019 Suitcase BoomBox
51/65
Use a hex key to remove the four corners screws on the front panel of the amplifier. Use a tiny
hex key to loosen the set screw from the knob, and remove the knob from the panel. then use
pliers to unscrew the nut attached to the knob's underlying potentiometer. The front panel
should come off easily.
Step 24: Mount amplifier
8/13/2019 Suitcase BoomBox
52/65
8/13/2019 Suitcase BoomBox
53/65
8/13/2019 Suitcase BoomBox
54/65
Use a pencil to mark the place on the enclosure where you would like to mount your amplifier's
front panel. I mounted mine on the side of my suitcase. Drill out holes for the 4 corner screws,
potentiometer, switch, and blue LEDs.
My suitcase enclosure added about 1/2" of extra space between the front panel and the rest of
the amplifier. Since the original screws weren't long enough to cover this distance, I went to
the hardware store and found some ~1.25" 3mm screws to replace them.
Screw through the suitcase enclosure to mount the front panel on the amplifier. The amplifier
is light enough that it will support itself by the screws alone.
Step 25: Connect charge controller to amplifier
Make sure the amplifier is switched to the off position and plug in the connection from the
charge controller.
Step 26: Mount external power supply jack
8/13/2019 Suitcase BoomBox
55/65
8/13/2019 Suitcase BoomBox
56/65
8/13/2019 Suitcase BoomBox
57/65
Drill a hole in the suitcase and mount the M-type barrel plug. My enclosure's walls were so
thick that I couldn't use a nut to lock the plug in place, I supplemented with super glue. You canuse the 12V wall wart or even a 12V solar panel to trickle charge your batteries through this
jack.
Step 27: Connect RCA cable to amplifier
8/13/2019 Suitcase BoomBox
58/65
Plug the red and white ends of the RCA cable to the amplifier input.
Step 28: Mount external audio jack to suitcase
8/13/2019 Suitcase BoomBox
59/65
8/13/2019 Suitcase BoomBox
60/65
8/13/2019 Suitcase BoomBox
61/65
8/13/2019 Suitcase BoomBox
62/65
In case you want to access the audio in from the outside of the case, mount an 1/8" stereo jack
to the side of the suitcase. Use some 22 gauge wire to connect the leads from the jack to an
inline female 1/8" stereo jack. Use electrical tape to cover any exposed solder points.
This way, you can store your audio devices inside the suitcase by plugging them directly to the
1/8" stereo jack to RCA cable that is plugged directly into the amplifier. Or you can plug the
1/8" stereo/RCA cable into the inline jack, and use a male to male stereo cable to hook up to
the external 1/8" jack.
Step 29: Create iPod/phone mount on inside of suitcase
8/13/2019 Suitcase BoomBox
63/65
To make thing really fancy, I used some of the extra fabric I removed in step 2, to create a little
pocket for holding my phone/iPod inside the suitcase.
Step 30: Rock out
8/13/2019 Suitcase BoomBox
64/65
8/13/2019 Suitcase BoomBox
65/65
You're done! Have fun! Be sure to check the voltage readout on the charge controller
occasionally and make sure the battery doesn't get too drained (the charge controller won't be
able to charge the batteries if they are completely drained).