Post on 21-Mar-2018
4 GEARS December 2014
One of the most problematic transmissions on the road today is AW55-50SN. This
transmission has been fitted to differ-ent vehicles from different manufactur-ers, including General Motors, Volvo, Saturn, Nissan, and Saab (These aren’t interchangeable as they have opera-tional differences).
The AW55-50SN is a 5-speed,
electronically controlled transmission. The TCM (transmission control mod-ule) sends signals to the solenoids to achieve the best possible ratio. The TCM also controls line pressure and the apply and release pressure for the torque converter clutch.
There have been some major prob-lems these transmissions, including valve body and solenoids wear. But
one problem can occur as a result of a simply fluid change. Here’s where the do-it-yourselfer (or even the transmis-sion professional) can find themselves in big trouble. That’s because the fill plug and band anchor look almost alike (figure 1). Loosening the anchor by mistake releases the band (resulting in no 3rd gear).
Figure two shows the band out of
AW55-50N/AF33-23/RE5F22A:No 3rd after Servicing
STREET SMART
by Mike Brownmembers.atra.com
Figure 1
Fill Band Anchor
1brown1214.indd 4 12/5/14 2:27 PM
GEARS December 2014 5
position once you remove the anchor. You can move the anchor back in place (figure 3) but as soon as you release it, the band moves out of place again.
The factory approved repair for this requires removing the transmission to install the band anchor correctly. And that’s an expensive proposition.
Just look up the R&I time on the vehicle you’re working on. For exam-ple a 2002 Volvo V-70 calls for 8.4 hours. At a labor rate of $89 an hour, that comes to $747.60, and that’s just R&I time. A lot of money for a self-inflicted wound.
But there’s some good news: You can repair this problem in less than an hour without removing the transmis-sion. I’m pretty sure your customer will be happy about that!
The repair involves creating an access point in the case that allows you to hold the band in place while you reinstall the anchor.
To make the repair, you’ll need:• 15/64” drill• 1/16”-27 NPT tap• 1/16” NPT plug
Figure 2
... most do-it-yourselfers don’t
know how to check and fill this
transmission
Figure 3
Moving Band Back Into Place
This Is What The Band Will Look Like When Out Of Place
1brown1214.indd 5 12/5/14 2:27 PM
6 GEARS December 2014
Here’s the procedure:1. Drill a 15/64” hole in the spot
marked with an “X” (figure 4). Hold the hose from a running shop vacuum by the case while you drill to keep any metal chips from getting into the transmis-sion.
2. Move the band back into place with the screwdriver, and slide a pick into the hole you drilled to hold the band in place.
3. Remove the screwdriver and install the band anchor.
4. Tap the hole so you can seal it with the plug; put a little grease on the tap to catch any shavings to keep them from getting into the transmission.
5. Install the plug with a drop or two of Loctite on the threads to help hold it in place (figure 5).
That’s all there is to it: problem solved! And all this in less than an hour.
Part of our job as transmission professionals is to minimize the amount of time it takes to make repairs, so as to keep the cost down for the custom-er. As simple procedure like this can save your customer a bundle, especially when they blunder a service like this. And that’s not just smart! That’s street smart!
Figure 4
The factory approved repair for this requires
removing the transmission to install the band anchor
correctly. And that’s
an expensive proposition.
Figure 5
X Marks The Spot
x
AW55-50N/AF33-23/RE5F22A: No 3rd after Servicing
1brown1214.indd 6 12/5/14 2:27 PM
2014 Parts Ads - REVISIONS2014 Ford Parts Ad - Badge- REVISION
Fonts: Ford Antenna (Medium, Black), Ford Antenna Cond (Medium)
Inks: Cyan, Magenta, Yellow, Black
Client:Ad #:
Agency #:Park #:
Live:Trim:
Bleed:
Ford Customer Service Div.FMQC1509000Afpvpw 1060282FCSD-006726.75” x 9.75”7.75” x 10”8.75” x 11.25”This document utilizes the Pantone + color library
Links: Park_QC Steps.eps (100%), Bullet.eps (100%), _DSC8062_V3_PPK.psd (CMYK; 300 ppi; 100%), FGBR_12GoFurther_4C_VtHt_R01.eps (32%), FCSD_FPcom_Wdmrk_Rv_R01.eps (31%)
Park ADD:Park Designer:
Park PM:Park Prod Artist:
NoneT. McCaffreyE. Luckhardtkozikowski, mark
Direct Mail Ops:Art Producer:
Account Super:Account Exec:
J. SparrowC. TalbotS. France
Legal:Product Info:Copy Editor:
Traffic:
N. Sulla
C. Oyama
Creative Director:Art Director:
Writer:Print Producer:
L. SimonciniT. Moy-MillerK. Pohl
Date: 11-6-2014 3:14 PM Rev: 2 Galley: 1File: FCSD00672_FMQC1509000A_Badge_PgAd_R02.indd
Engraver:Doc Scale:
Output Size:Media/Type:
None100%100%Magazine
Note:
S:6.75”
S:9.75”T:7.75”
T:10”B:8.75”
B:11.25”
With FordParts.com, a simple VIN grants you 24-hour access to the exact parts you need. And, while you’re there, you’ll fi nd it’s the fastest, easiest way to get assembly diagrams, shipping and delivery options, business tools and so much more. No matter what your name is, let VIN fi nd the right part. So get cleared for access.
THE NAME OF THE GAME IS FINDING THE RIGHT PART.
ford 1214.indd 2 12/8/14 1:24 AM