Post on 02-Oct-2021
Sprinter Technical Data
Panel Van (FWD and RWD), Cab Chassis and Dual Cab Chassis (RWD) | Euro VIJanuary 2020
Sprinter | Drivetrain2
Drivetrain availability across the Sprinter rangePanel Van Cab Chassis Dual Cab Chassis Transfer Minibus
FWD RWD FWD RWD FWD RWD FWD RWDSWB311 CDi (84 kW) • - - - - - - -314 CDi (105 kW) • - - - - - - -MWB311 CDi (84 kW) • • - - - - - -314 CDi (105 kW) • • - - - - - -316 CDi (120 kW) - • - - - - - -319 CDi (140 kW) - • - - - - - -411 CDi (84 kW) - - - - - - - -414 CDi (105 kW) - • - - - - - •416 CDi (120 kW) - • - - - - - •419 CDi (140 kW) - • - - - - - -516 CDi (120 kW) - • - • - • - -519 CDi (140 kW) - - - • - - - -LWB314 CDi (105 kW) - • - - - - - -316 CDi (120 kW) - • - - - - - -319 CDi (140 kW) - • - - - - - -414 CDi (105 kW) - • - - - - - -416 CDi (120 kW) - • - - - - - -419 CDi (140 kW) - • - - - - - -516 CDi (120 kW) - • - • - • - -519 CDi (140 kW) - • - • - • - -ELWB316 CDi (120 kW) - • - - - - - -416 CDi (120 kW) - • - - - - - -516 CDi (120 kW) - • - - - - - -
Engine Specification84 kW (114hp) at 3800 rpm | 4 cylinders | Diesel2 | Engine OM651 | Twin-TurbochargedEuro VI | 2143 cc | 300 Nm at 1,400-2,400 rpm | Fuel Tank Capacity 71l Eco Gear 360 6-speed manual transmission (RWD)84 kW (114 hp) at 3800 rpm | 4 cylinders | Diesel2 | Engine OM651 | Single-Turbocharged Euro VI | 2143 cc | 300 Nm at 1200-2200 rpm | Fuel Tank Capacity 65l 6-speed manual transmission (FWD)105 kW (143hp) at 3800 rpm | 4 cylinders | Diesel2 | Engine OM651 | Twin-Turbocharged Euro VI | 2143 cc | 330 Nm at 1200–2400 rpm | Fuel Tank Capacity 71l | Eco Gear 360 6-speed manual transmission (RWD)105 kW (143hp) at 3800 rpm | 4 cylinders | Diesel2 | Engine OM651 | Single-Turbocharged Euro VI | 2143 cc | 330 Nm at 1200–2400 rpm | Fuel Tank Capacity 65l | 6-speed manual transmission (FWD)120 kW (163hp) at 3800 rpm | 4 cylinders | Diesel2 | Engine OM651 | Twin-Turbocharged Euro VI | 2143 cc | 360 Nm at 1400–2400 rpm | Fuel Tank Capacity 71l Eco Gear 360 6-speed manual transmission (RWD)140 kW (190hp) at 3800 rpm | 6 cylinders/V 72° | Diesel2 | Engine OM642 | Single-Turbocharged Euro VI | 2987 cc | 440 Nm at 1400–2400 rpm | Fuel Tank Capacity 71l | 7G-TRONIC automatic transmission (RWD)
Standard Equipment Panel Van - FWD and RWD
ExteriorRadiator grille frame in vehicle colour Electrically foldable exterior mirrorsExterior mirror heated and electrically adjustableSide marker lightsFront mud flapsRear mud flapsWindow in tailgate / Rear hinged doorsRear door step
InteriorKeyless StartPaddle Gear Shifter (where applicable)Entrance handle on RH rear corner pillarGrab handles for driver's and co-driver's doorsMultifunction steering wheelHeight and rake adjustable steering wheelMBUX multimedia system with 7-inch touch screenRear mirror insideShelf above windscreenCup holders frontHinged lid for stowage compartmentStowage compartment underneath cockpitHeat-insulating glass with band filter on windscreenHeated rear window (FWD only)Air conditioning semi-autom. controlled TEMPMATICInstrument cluster with colour displayOverhead control panel with 2 reading lampsAdjustable driver and passenger seatFabric Caluma blackLashing eyelets
SafetyActive Brake AssistBlind Spot AssistLane Keeping AssistATTENTION ASSISTADAPTIVE Electronic Stability Program (ESP9i) incorporates:- Hill-Start Assist- Acceleration Skid Control (ASR)- Brake Assist (BAS)- Anti-locking Braking System (ABS)- Crosswind Assist - Electronic Brake Force Distribution (EBD)- Brake Disc Wipers- Electronic Brake Prefill- Enhanced Understeer Control (EUC)- Load Adaptive Control (LAC)- Roll-Over Mitigation (ROM)- Roll Movement Intervention (RMI)- ESP Trailer Stabilisation (TSA)- Easy Lane Change (ELC)Reversing cameraSeat belt reminder for co-driver seatSeat belt warning for driver's seatIllumination for traffic driving on leftHeadlight assistant3rd brake lightAdaptive brake lightCruise controlAirbag front driver and co-driver's seatWindowbags for driver and co-driverDaytime running lights
TechnicalHeavy-duty batteryPre-installations electrical system PSMTerminal strip for electrical connectionStarting aid contactCharging package dashboardMulti-button radio remote controlTemperature indicatorTank 65 Litre (FWD) | 71 Litre (RWD)Filler cap diesel in redExhaust straight to chassis rearFuel filter with water separatorECO start/stop functionLongitudinal member reinforcement6-speed manual transmission (FWD)ECO Gear 360 6-speed manual transmission (RWD)7G-TRONIC automatic transmission (319, 419, 519)Engine Power take-off at front with carrier for additional refrigerant Compressor (RWD only)
LoadElectrical components for trailer socketSliding door leftRear Barn Doors on ELWBTowing eye rear (RWD)
Warranty3 year/200,000km24 hour roadside assist support package, see MBVRoadCare booklet for full details
3Sprinter | Standard Equipment
Standard Equipment Cab Chassis - RWD | Dual Cab Chassis - RWD
ExteriorRadiator grille frame in vehicle colour Electrically foldable exterior mirrorsExterior mirror heated and electrically adjustablePreparation for side marker lightsFront mud flaps
InteriorKeyless StartPaddle Gear Shifter (where applicable)Grab handles for driver's and co-driver's doorsMultifunction steering wheelHeight and rake adjustable steering wheelMBUX multimedia system with 7-inch touch screenRear wall windowRear mirror insideShelf above windscreenCup holders frontHinged lid for stowage compartmentStowage compartment underneath cockpitHeat-insulating glass with band filter on windscreenAir conditioning semi-autom. controlled TEMPMATICInstrument cluster with colour displayOverhead control panel with 2 reading lampsCo-driver's seat double seat (Only on Cab Chassis)Adjustable driver and passenger seatFabric Caluma blackMultifunction box on two-seater stowable (Only on Cab Chassis)*
SafetyActive Brake AssistLane Keeping AssistATTENTION ASSISTADAPTIVE Electronic Stability Program (ESP9i) incorporates:- Hill-Start Assist- Acceleration Skid Control (ASR)- Brake Assist (BAS)- Anti-locking Braking System (ABS)- Crosswind Assist - Electronic Brake Force Distribution (EBD)- Brake Disc Wipers- Electronic Brake Prefill- Enhanced Understeer Control (EUC)- Load Adaptive Control (LAC)- Roll-Over Mitigation (ROM)- Roll Movement Intervention (RMI)- ESP Trailer Stabilisation (TSA)- Easy Lane Change (ELC)Multi-button radio remote controlSeat belt reminder for co-driver seatSeat belt warning for driver's seatIllumination for traffic driving on leftHeadlight assistant3rd brake lightAdaptive brake lightCruise controlAirbag front driver and co-driver's seatWindowbags for driver and co-driverDaytime running lights
TechnicalHeavy-duty batteryPre-installations electrical system PSMTerminal strip for electrical connectionStarting aid contactCharging package dashboardProvision electrics reversing aidTemperature indicator71 Litre (RWD)Filler cap diesel in redFuel filter with water separatorECO start/stop functionLongitudinal member reinforcementSpare wheel bracket below frame endSpare wheelECO Gear 360 6-speed manual transmission (RWD)7G-TRONIC automatic transmission (419, 519)Engine Power take-off at front with carrier for additional refrigerant Compressor (RWD only)
LoadElectrical components for trailer socket
Warranty3 year/200,000km24 hour roadside assist support package, see MBVRoadCare booklet for full details
Sprinter | Standard Equipment4
5Sprinter | Standard Equipment
Transfer Minibus Standard Equipment (RWD)
ExteriorRadiator grille frame in vehicle colourElectrically foldable exterior mirrors Exterior mirror heated and electrically adjustableSide marker lights Front mud flaps Rear mud flaps Window in tailgate/Rear hinged doors Rear door step Chrome grille (Only on 416)Light and rain sensor (Only on 416)Fog Lamps with cornering light function (Only on 416)High beam Assist (Only on 416)16” light alloy wheels (Only on 416)LED High Performance headlamps (Only on 416)Electric Left hand side sliding door (Only on 416)Intermediate detent for load compartment sliding door (Only on 414)Left Hand Sliding door closing door assist (Only on 414)
TechnicalHeavy-duty battery Terminal strip for electrical connection Starting aid contact Charging package dashboard Temperature indicator Tank 71 Litre (RWD) Filler cap diesel in red Exhaust straight to chassis rear Fuel filter with water separator ECO start/stop function Longitudinal member reinforcement 7G-TRONIC automatic transmission Engine Power take-off at front with carrier for additional refrigerant Compressor
InteriorSeating capacity for 12 ( Seating Configuration 3+2+3+4)Keyless Start Paddle Gear Shifter Entrance handle on RH rear corner pillar Grab handles for driver's and co-driver's doors Multifunction steering wheel Height and rake adjustable steering wheel MBUX multimedia system with 7-inch touch screen Rear mirror inside Shelf above windscreen Cup holders front Hinged lid for stowage compartment Stowage compartment underneath cockpit Heat-insulating glass with band filter on windscreen Roof-mounted air conditioning system, basic (no heating function)Air conditioning semi-auto. controlled TEMPMATIC Instrument cluster with colour display Overhead control panel with 2 reading lamps (Only on 414)Comfort overhead control panel (Only on 416)Window pillar panelling (Only on 416)Comfort driver seat Co-driver's seat double seatInterior panelling luxuryPanelling under roof2 Way loudspeakers front and rearLumbar Support driver seatMultifunction box on two-seater
LoadElectrical components for trailer socket Sliding door left Towing eye rear (RWD)
SafetyActive Brake Assist Blind Spot Assist Lane Keeping Assist ATTENTION ASSIST ADAPTIVE Electronic Stability Program (ESP9i) incorporates: - Hill-Start Assist - Acceleration Skid Control (ASR) - Brake Assist (BAS) - Anti-locking Braking System (ABS) - Crosswind Assist - Electronic Brake Force Distribution (EBD) - Brake Disc Wipers - Electronic Brake Prefill - Enhanced Understeer Control (EUC) - Load Adaptive Control (LAC) - Roll-Over Mitigation (ROM) - Roll Movement Intervention (RMI) - ESP Trailer Stabilisation (TSA) - Easy Lane Change (ELC) Reversing camera Parameterizable special module (PSM)Multi-button radio remote control Electric side step for rear passenger compartmentSeat belt reminder for co-driver seat Seat belt warning for driver's seat Illumination for traffic driving on left Headlight assistant 3rd brake light Adaptive brake light Cruise controlAirbag front driver and co-driver's seat Windowbags for driver and co-driver
Warranty3 year/200,000km 24 hour roadside assist support package, see MBV RoadCare booklet for full details
6 Panel Van | Technical Data
Designation VS30 SprinterBody Style FWD Panel VanVariant 311 SWB 314 SWB 311 MWB 314 MWBModel Type / Baumuster 91063123 91063123 91063323 91063323Engine 651 651 651 651Capacity [cc] 2143 2143 2143 2143Max. Power [kW] 84 105 84 105Fuel Capacity [liter] 65 65 65 65Length [mm] 5267 5267 5932 5932Width [mm] 2020 2020 2020 2020Height (Std. Roof) [mm] 2356 2356 2351 2351Cargo Vol. (Std. Roof) [m3] 7.8 7.8 9.5 9.5Height (High Roof) [mm] 2642 2642 2638 2638Cargo Vol. (High Roof) [m3] 8.8 8.8 11 11Ground Clearance [mm] 143 143 143 143Wheelbase [mm] 3259 3259 3924 3924Overhang [mm] 996 996 996 996Transmission 6MT 9AT 6MT 9AT 6MT 9AT 6MT 9ATMaximum Towing [kg] 2000 2000 2000 2000 2000 2000 2000 2000GCM1 [kg] 5550 5550 5550 5550 5550 5550 5550 5550GVM2 [kg] 3550 3550 3550 3550 3550 3550 3550 3550Front Axle Mass Limit3 [kg] 1750 1750 1750 1750 1750 1750 1750 1750Rear Axle Mass Limit [kg] 2100 2100 2100 2100 2100 2100 2100 2100Payload4 [kg] 1541 1523 1541 1523 1474 1456 1474 1456Unladen Mass5 [kg] 2009 2027 2009 2027 2076 2094 2076 2094EU Kerb Mass6 [kg] 2079 2097 2079 2097 2146 2164 2146 2164Tare Mass7 [kg] 1963 1981 1963 1981 2030 2048 2030 2048
Technical Data FWD Panel Van | Euro VI | 3.55t
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupantsWeights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Technical Data RWD Panel Van | Euro VI | 3.55t
Designation VS30 Sprinter Body Style Euro VI RWD Panel VanVariant 311 MWB 314 MWB 316 MWB 319 MWB 314 LWB 316 LWB 319 LWB 316 EXLModel Type / Baumuster 90763323 90763323 90763323 90763323 90763523 90763523 90763523 90763723Engine 651 651 651 642 651 651 642 651Capacity [cc] 2143 2143 2143 2987 2143 2143 2987 2143Max. Power [kW] 84 105 120 140 105 120 140 120Fuel Capacity [liter] 71 71 71 71 71 71 71 71Length [mm] 5932 5932 5932 5932 6967 6967 6967 7367Width [mm] 2020 2020 2020 2020 2020 2020 2020 2020Height (Std. Roof) [mm] 2331 2331 2331 2331 na na na naCargo Vol. (Std. Roof) [m3] 9 9 9 9 na na na naHeight (High Roof) [mm] 2620 2620 2620 2620 2616 2616 2616 2643Cargo Vol. (High Roof) [m3] 10.5 10.5 10.5 10.5 14 14 14 15.5Height (Super High Roof) [mm] na na na na 2831 2831 2831 2855Cargo Vol. (Super High Roof) [m3] na na na na 15.5 15.5 15.5 17.0Ground Clearance [mm] 162 162 162 162 161 161 161 188Wheelbase [mm] 3665 3665 3665 3665 4325 4325 4325 4325Overhang [mm] 1246 1246 1246 1246 1621 1621 1621 2021Transmission 6MT 7AT 6MT 7AT 6MT 7AT na 7AT 6MT 7AT 6MT 7AT na 7AT 6MT 7ATAxle Ratio 4.182 4.182 3.923 3.923 3.923 3.692 na 3.692 3.923 3.923 3.923 3.692 na 3.692 3.923 3.692Maximum Towing [kg] 2000 2000 2000 2000 2000 2000 na 2000 2000 2000 2000 2000 na 2000 2000 2000GCM1 [kg] 5550 5550 5550 5550 5550 5550 na 5550 5550 5550 5550 5550 na 5550 5550 5550GVM2 [kg] 3550 3550 3550 3550 3550 3550 na 3550 3550 3550 3550 3550 na 3550 3550 3550Front Axle Mass Limit3 [kg] 1650 1650 1650 1650 1650 1650 na 1650 1650 1650 1650 1650 na 1650 1650 1650Rear Axle Mass Limit [kg] 2250 2250 2250 2250 2250 2250 na 2250 2250 2250 2250 2250 na 2250 2250 2250Payload4 [kg] 1398 1380 1398 1380 1398 1380 na 1356 1219 1201 1219 1201 na 1177 1172 1154Unladen Mass5 [kg] 2152 2170 2152 2170 2152 2170 na 2194 2331 2349 2331 2349 na 2373 2378 2396EU Kerb Mass6 [kg] 2221 2239 2221 2239 2221 2239 na 2263 2400 2418 2400 2418 na 2442 2447 2465Tare Mass7 [kg] 2101 2119 2101 2119 2101 2119 na 2143 2280 2298 2280 2298 na 2322 2327 2345
7Panel Van | Technical Data
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupantsWeights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.
Panel Van |Technical Data8
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.
Technical Data RWD Panel Van | Euro VI | 4.10t
Designation VS30 Sprinter Body Style Euro VI RWD Panel VanVariant 414 MWB 416 MWB 419 MWB 414 LWB 416 LWB 419 LWB 416 EXLModel Type / Baumuster 90764323 90764323 90764323 90764523 90764523 90764523 90764723Engine 651 651 642 651 651 642 651Capacity [cc] 2143 2143 2987 2143 2143 2987 2143Max. Power [kW] 105 120 140 105 120 140 120Fuel Capacity [liter] 71 71 71 71 71 71 71Length [mm] 5932 5932 5932 6967 6967 6967 7367Width [mm] 2020 2020 2020 2020 2020 2020 2020Height (Std. Roof) [mm] 2378 2378 2378 na na na naCargo Vol. (Std. Roof) [m3] 9 9 9 na na na naHeight (High Roof) [mm] 2667 2667 2667 2663 2663 2663 2662Cargo Vol. (High Roof) [m3] 10.5 10.5 10.5 14 14 14 15.5Height (Super High Roof) [mm] na na na 2878 2878 2878 2873Cargo Vol. (Super High Roof) [m3] na na na 15.5 15.5 15.5 17.0Ground Clearance [mm] 163 163 163 163 163 163 162Wheelbase [mm] 3665 3665 3665 4325 4325 4325 4325Overhang [mm] 1246 1246 1246 1621 1621 1621 2021Transmission 6MT 7AT 6MT 7AT na 7AT 6MT 7AT 6MT 7AT na 7AT 6MT 7ATAxle Ratio 4.182 3.923 3.923 3.692 na 3.692 4.182 3.923 3.923 3.692 na 3.692 3.923 3.692Maximum Towing [kg] 2000 2000 2000 2000 na 2000 2000 2000 2000 2000 na 2000 2000 2000GCM1 [kg] 6100 5500 5500 5500 na 6100 6100 5500 5500 5500 na 6100 5500 5500GVM2 [kg] 4100 4100 4100 4100 na 4100 4100 4100 4100 4100 na 4100 4100 4100Front Axle Mass Limit3 [kg] 1860 1860 1860 1860 na 1860 1860 1860 1860 1860 na 1860 1860 1860Rear Axle Mass Limit [kg] 2430 2430 2430 2430 na 2430 2430 2430 2430 2430 na 2430 2430 2430Payload4 [kg] 1939 1921 1939 1921 na 1897 1760 1742 1760 1742 na 1718 1713 1695Unladen Mass5 [kg] 2161 2179 2161 2179 na 2203 2340 2358 2340 2358 na 2382 2387 2405EU Kerb Mass6 [kg] 2230 2248 2230 2248 na 2272 2409 2427 2409 2427 na 2451 2456 2474Tare Mass7 [kg] 2110 2128 2110 2128 na 2152 2289 2307 2289 2307 na 2331 2336 2354
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupantsWeights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Technical Data RWD Panel Van | Euro VI | 4.49t
Designation VS30 Sprinter 4.49t Body Style Euro VI RWD Panel VanVariant 516 MWB 516 LWB 519 LWB 516 EXLModel Type / Baumuster 90765323 90765523 90765523 90765723Engine 651 651 642 651Capacity [cc] 2143 2143 2987 2143Max. Power [kW] 120 120 140 120Fuel Capacity [liter] 71 71 71 71Length [mm] 5932 6967 6967 7367Width [mm] 2020 2020 2020 2020Height (Std. Roof) [mm] 2422 na na naCargo Vol. (Std. Roof) [m3] 8.9 na na naHeight (High Roof) [mm] 2710 2706 2706 2703Cargo Vol. (High Roof) [m3] 10.4 13.9 13.9 15.4Height (Super High Roof) [mm] na 2917 2917 2912Cargo Vol. (Super High Roof) [m3] na 15.4 15.4 16.9Ground Clearance [mm] 176 176 176 176Wheelbase [mm] 3665 4325 4325 4325Overhang [mm] 1246 1621 1621 2021Transmission 6MT 7AT 6MT 7AT na 7AT 6MT 7ATAxle Ratio 4.182 4.182 4.182 4.182 na 3.923 4.182 4.182Maximum Towing [kg] 3500 3500 3500 3500 na 3500 3500 3500GCM1 [kg] 6490 6490 6490 6490 na 6490 6490 6490GVM2 [kg] 4490 4490 4490 4490 na 4490 4490 4490Front Axle Mass Limit3 [kg] 1850 1850 1850 1850 na 1850 1850 1850Rear Axle Mass Limit [kg] 3200 3200 3200 3200 na 3200 3200 3200Payload4 [kg] 2145 2127 1953 1935 na 1911 1916 1898Unladen Mass5 [kg] 2345 2363 2537 2555 na 2579 2574 2592EU Kerb Mass6 [kg] 2414 2432 2606 2624 na 2648 2643 2661Tare Mass7 [kg] 2294 2312 2486 2504 na 2528 2523 2541
Panel Van | Technical Data 9
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupantsWeights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
10 Panel Van |Technical Data
Technical Data RWD Panel Van | Euro VI | 5.0t
Designation VS30 Sprinter HD 5.0tBody Style Euro VI RWD Panel VanVariant 516 MWB 516 LWB 519 LWBModel Type / Baumuster 90765323 90765523 90765523Engine 651 651 642Capacity [cc] 2143 2143 2987Max. Power [kW] 120 120 140Fuel Capacity [liter] 71 71 71Length [mm] 5932 6967 6967Width [mm] 2020 2020 2020Height (Std. Roof) [mm] 2422 na naCargo Vol. (Std. Roof) [m3] 8.9 na naHeight (High Roof) [mm] 2710 2706 2706Cargo Vol. (High Roof) [m3] 10.4 13.9 13.9Height (Super High Roof) [mm] na 2917 2917Cargo Vol. (Super High Roof) [m3] na 15.4 15.4Ground Clearance [mm] 176 176 176Wheelbase [mm] 3665 4325 4325Overhang [mm] 1246 1621 1621Transmission 6MT 7AT 6MT 7AT na 7ATAxle Ratio 4.182 4.182 4.182 4.182 na 3.923Maximum Towing [kg] 3500 3500 3500 3500 na 3500GCM1 [kg] 7000 7000 7000 7000 na 7000GVM2 [kg] 5000 5000 5000 5000 na 5000Front Axle Mass Limit3 [kg] 1850 1850 1850 1850 na 1850Rear Axle Mass Limit [kg] 3500 3500 3500 3500 na 3500Payload4 [kg] 2655 2637 2463 2445 na 2421Unladen Mass5 [kg] 2345 2363 2537 2555 na 2579EU Kerb Mass6 [kg] 2414 2432 2606 2624 na 2648Tare Mass7 [kg] 2294 2312 2486 2504 na 2528
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupantsWeights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Cab Chassis | Technical Data 11
Technical Data RWD Cab Chassis | Euro VI | 4.49t
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)Factory Tray option increases kerb mass by 300-500 kg.Factory Tray option decreases payload by 300-500 kg.All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.Weights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Designation VS30 SprinterBody Style RWD Single Cab ChassisVariant 516 MWB 519 MWB 516 LWB 519 LWBModel Type / Baumuster 90715323 90715323 90715523 90715523Engine 651 642 651 642Capacity [cc] 2143 2987 2143 2987Max. Power [kW] 120 140 120 140Fuel Capacity [liter] 71 71 71 71Length [mm] 6104 6104 6864 6864Width [mm] 2020 2020 2020 2020Height [mm] 2360 2360 2351 2351Ground Clearance [mm] 176 176 176 176Wheelbase [mm] 3665 3665 4325 4325Overhang [mm] 1418 1418 1518 1518Transmission 6MT 7AT na 7AT 6MT 7AT na 7ATAxle Ratio 4.182 4.182 na 3.923 4.182 4.182 na 3.923Maximum Towing [kg] 3500 3500 na 3500 3500 3500 na 3500GCM1 [kg] 6490 6490 na 6490 6490 6490 na 6490GVM2 [kg] 4490 4490 na 4490 4490 4490 na 4490Front Axle Mass Limit3 [kg] 1850 1850 na 1850 1850 1850 na 1850Rear Axle Mass Limit [kg] 3200 3200 na 3200 3200 3200 na 3200Payload4 [kg] 2417 2399 na 2375 2379 2361 na 2337Unladen Mass5 [kg] 2073 2091 na 2115 2111 2129 na 2153EU Kerb Mass6 [kg] 2142 2160 na 2184 2180 2198 na 2222Tare Mass7 [kg] 2022 2040 na 2064 2060 2078 na 2102Body Style RWD Single Cab with TrayLength [mm] 6246 6246 6946 6946Width [mm] 2199 2199 2199 2199Height (std) [mm] 2348 2348 2337 2337Overhang [mm] 1560 1560 1600 1600
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupants
Cab Chassis | Technical Data12
NOTE: ass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)Factory Tray option increases kerb mass by 300-500 kg.Factory Tray option decreases payload by 300-500 kg.All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.Weights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Designation VS30 SprinterBody Style RWD Single Cab ChassisVariant 516 MWB 519 MWB 516 LWB 519 LWBModel Type / Baumuster 90715323 90715323 90715523 90715523Engine 651 642 651 642Capacity [cc] 2143 2987 2143 2987Max. Power [kW] 120 140 120 140Fuel Capacity [liter] 71 71 71 71Length [mm] 6104 6104 6864 6864Width [mm] 2020 2020 2020 2020Height [mm] 2360 2360 2351 2351Ground Clearance [mm] 176 176 176 176Wheelbase [mm] 3665 3665 4325 4325Overhang [mm] 1418 1418 1518 1518Transmission 6MT 7AT na 7AT 6MT 7AT na 7ATAxle Ratio 4.182 4.182 na 3.923 4.182 4.182 na 3.923Maximum Towing [kg] 3500 3500 na 3500 3500 3500 na 3500GCM1 [kg] 7000 7000 na 7000 7000 7000 na 7000GVM2 [kg] 5000 5000 na 5000 5000 5000 na 5000Front Axle Mass Limit3 [kg] 1850 1850 na 1850 1850 1850 na 1850Rear Axle Mass Limit [kg] 3500 3500 na 3500 3500 3500 na 3500Payload4 [kg] 2927 2909 na 2885 2889 2871 na 2847Unladen Mass5 [kg] 2073 2091 na 2115 2111 2129 na 2153EU Kerb Mass6 [kg] 2142 2160 na 2184 2180 2198 na 2222Tare Mass7 [kg] 2022 2040 na 2064 2060 2078 na 2102Body Style RWD Single Cab with TrayLength [mm] 6246 6246 6946 6946Width [mm] 2199 2199 2199 2199Height (std) [mm] 2348 2348 2337 2337Overhang [mm] 1560 1560 1600 1600
Technical Data RWD Cab Chassis | Euro VI | 5.0t
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupants
13Dual Cab Chassis | Technical Data
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)Factory Tray option increases kerb mass by 300-500 kg.Factory Tray option decreases payload by 300-500 kg.All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.Weights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Technical Data RWD Dual Cab Chassis | Euro VI | 4.49t
Designation VS30 SprinterBody Style RWD Dual Cab ChassisVariant 516 MWB 516 LWB 519 LWBModel Type / Baumuster 90725323 90725523 90725523Engine 651 651 642Capacity [cc] 2143 2143 2987Max. Power [kW] 120 120 140Fuel Capacity [liter] 71 71 71Length [mm] 6104 6864 6864Width [mm] 2020 2020 2020Height [mm] 2358 2345 2345Ground Clearance [mm] 176 176 176Wheelbase [mm] 3665 4325 4325Overhang [mm] 1418 1518 1518Transmission 6MT 7AT 6MT 7AT na 7ATAxle Ratio 4.182 4.182 4.182 4.182 na 3.923Maximum Towing [kg] 3500 3500 3500 3500 na 3500GCM1 [kg] 6490 6490 6490 6490 na 6490GVM2 [kg] 4490 4490 4490 4490 na 4490Front Axle Mass Limit3 [kg] 1850 1850 1850 1850 na 1850Rear Axle Mass Limit [kg] 3200 3200 3200 3200 na 3200Payload4 [kg] 2245 2227 2207 2189 na 2165Unladen Mass5 [kg] 2245 2263 2283 2301 na 2325EU Kerb Mass6 [kg] 2314 2332 2352 2370 na 2394Tare Mass7 [kg] 2194 2212 2232 2250 na 2274Body Style RWD Dual Cab Chassis with TrayLength [mm] 6156 7056 7056Width [mm] 2199 2199 2199Height (std) [mm] 2345 2345 2345Overhang [mm] 1470 1710 1710
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupants
14 Dual Cab Chassis | Technical Data
Technical Data RWD Dual Cab Chassis | Euro VI | 5.0t
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)Factory Tray option increases kerb mass by 300-500 kg.Factory Tray option decreases payload by 300-500 kg.All-wheel drive option increases kerb mass by 140-200 kg.All-wheel drive option decreases payload by 140-200 kg.Weights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupants
Designation VS30 Sprinter HDBody Style RWD Dual Cab ChassisVariant 516 MWB 516 LWB 519 LWBModel Type / Baumuster 90725323 90725523 90725523Engine 651 651 642Capacity [cc] 2143 2143 2987Max. Power [kW] 120 120 140Fuel Capacity [liter] 71 71 71Length [mm] 6104 6864 6864Width [mm] 2020 2020 2020Height [mm] 2358 2345 2345Ground Clearance [mm] 176 176 176Wheelbase [mm] 3665 4325 4325Overhang [mm] 1418 1518 1518Transmission 6MT 7AT 6MT 7AT na 7ATAxle Ratio 4.182 4.182 4.182 4.182 na 3.923Maximum Towing [kg] 3500 3500 3500 3500 na 3500GCM1 [kg] 7000 7000 7000 7000 na 7000GVM2 [kg] 5000 5000 5000 5000 na 5000Front Axle Mass Limit3 [kg] 1850 1850 1850 1850 na 1850Rear Axle Mass Limit [kg] 3500 3500 3500 3500 na 3500Payload4 [kg] 2755 2737 2717 2699 na 2675Unladen Mass5 [kg] 2245 2263 2283 2301 na 2325EU Kerb Mass6 [kg] 2314 2332 2352 2370 na 2394Tare Mass7 [kg] 2194 2212 2232 2250 na 2274Body Style RWD Dual Cab Chassis with TrayLength [mm] 6156 7056 7056Width [mm] 2199 2199 2199Height (std) [mm] 2345 2345 2345Overhang [mm] 1470 1710 1710
Transfer Minibus | Technical Data 15
Technical Data RWD Transfer Minibus | Euro VI | 4.10t
NOTE: Mass variations (mass ranges provided depend upon individual model - see your dealer for more information if required)
Weights are intended as a guide only. For accuracy, the actual vehicle should always be weighed to determine the exact weight for the specifications ordered. Weight tolerance of +/- 5% in production, and additional weight of optional equipment must be taken in consideration.
Disclaimer1 Gross Combination Mass (GCM) is the total permissible combined weight of the vehicle including occupants, fuel, cargo plus trailer being towed if any.2 Gross Vehicle Mass (GVM) is the total permissible weight of the vehicle including occupants, fuel and cargo.3 Front Axle Mass Limit without A50.4 Payload = GVM - Unladen mass⁵ Unladen mass = vehicle with all standard equipment, 100% fuel and no occupants6 EU Kerb Mass = Mass of the unladen vehicle with a 75kg driver, 90% fuel and 100% of all other fluids7 Tare Mass = 10 litres fuel, no occupants
Designation VS30 SprinterBody Style Euro VI (MP6) RWD Transfer MinibusVariant 414 MWB 416 MWBModel Type / Baumuster: 90764323 90764323Engine 651 651Capacity [cc] 2143 2143Max. Power [kW] 105 120Fuel Capacity [liter] 71 71Length [mm] 5932 5932Width [mm] 2020 2020Height (std) [mm] 2578 2578Cargo Vol. (std) [m3] 9 9Height (D03) [mm] 2867 2867Cargo Vol. (D03) [m3] 10.5 10.5Height (D06) [mm] na naCargo Vol. (D06) [m3] na naGround Clearance [mm] 163 163Wheelbase [mm] 3665 3665Overhang [mm] 1246 1246Seating standard, including driver 12 (9+2+1) 12 (9+2+1)Transmission 7AT 7ATAxle Ratio 3.923 3.692Maximum Towing [kg] 2000 2000GCM1 [kg] 5500 5500GVM2 [kg] 4100 4100Front Axle Mass Limit3 [kg] 1860 1860Rear Axle Mass Limit [kg] 2430 2430Payload4 [kg] 1465 1455Unladen Mass5 [kg] 2635 2645EU Kerb Mass Total6 [kg] 2704 2714Tare Mass7 [kg] 2584 2594
Panel Van | Technical Drawings16
Technical Drawings Panel Van - Short Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH1/FWD 4x2/3500
910631 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A7,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143576
laden unladen2356
410N/A
143433
2222
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH2/FWD 4x2/3500
910631 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
144572
laden unladen2642
410N/A
143433
2511
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH1/FWD 4x2/3500
910631 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A7,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143576
laden unladen2356
410N/A
143433
2222
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH2/FWD 4x2/3500
910631 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
144572
laden unladen2642
410N/A
143433
2511
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH1/FWD 4x2/3500
910631 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A7,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143576
laden unladen2356
410N/A
143433
2222
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH2/FWD 4x2/3500
910631 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
144572
laden unladen2642
410N/A
143433
2511
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
FWD, 3.55T, Standard Roof
FWD, 3.55T, High roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH1/FWD 4x2/3500
910631 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A7,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143576
laden unladen2356
410N/A
143433
2222
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA1LH2/FWD 4x2/3500
910631 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,8
12,2N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
144572
laden unladen2642
410N/A
143433
2511
344N/A
4,357
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
17Panel Van | Technical Drawings
Technical Drawings Panel Van - Medium Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/FWD 4x2/3500
910633 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9,5
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143569
laden unladen2351
403N/A
143433
2220
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/FWD 4x2/3500
910633 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A11
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143566
laden unladen2638
402N/A
143433
2511
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/FWD 4x2/3500
910633 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9,5
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143569
laden unladen2351
403N/A
143433
2220
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/FWD 4x2/3500
910633 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A11
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143566
laden unladen2638
402N/A
143433
2511
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/FWD 4x2/3500
910633 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9,5
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143569
laden unladen2351
403N/A
143433
2220
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/FWD 4x2/3500
910633 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A11
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143566
laden unladen2638
402N/A
143433
2511
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/FWD 4x2/3500
910633 12.12.2019
D93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9,5
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143569
laden unladen2351
403N/A
143433
2220
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/FWD 4x2/3500
910633 12.12.2019
D03 high roofD93 omission of partitionMR6 low-emissions vehicle Euro 6c Gr. IIIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A11
14,4N/A
17502100
Optional equipment: Important notes:
Front axleRear axle
225/65 R16CBase tyres:
225/65 R16C
143566
laden unladen2638
402N/A
143433
2511
343N/A
5,539
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
FWD, 3.55T, Standard roof
FWD, 3.55T, High roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Panel Van | Technical Drawings18
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/3500
907633 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162628
laden unladen2331
406N/A
158520
2227
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/3500
907633 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162626
laden unladen2620
405N/A
158520
2518
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/3500
907633 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162628
laden unladen2331
406N/A
158520
2227
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/3500
907633 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162626
laden unladen2620
405N/A
158520
2518
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/3500
907633 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162628
laden unladen2331
406N/A
158520
2227
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/3500
907633 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162626
laden unladen2620
405N/A
158520
2518
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/3500
907633 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162628
laden unladen2331
406N/A
158520
2227
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/3500
907633 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
16502250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162626
laden unladen2620
405N/A
158520
2518
351N/A
5,081
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 3.55T, Standard roof
RWD, 3.55T, High roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Panel Van - Medium Wheelbase
Panel Van | Technical Drawings 19
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/4100
907643 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163675
laden unladen2378
446N/A
160559
2266
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/4100
907643 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163673
laden unladen2667
445N/A
160559
2556
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/4100
907643 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163675
laden unladen2378
446N/A
160559
2266
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/4100
907643 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163673
laden unladen2667
445N/A
160559
2556
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/4100
907643 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163675
laden unladen2378
446N/A
160559
2266
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/4100
907643 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163673
laden unladen2667
445N/A
160559
2556
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/4100
907643 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A9
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163675
laden unladen2378
446N/A
160559
2266
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/4100
907643 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,5
12,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163673
laden unladen2667
445N/A
160559
2556
375N/A
5,081
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.1T, Standard roof
RWD, 4.1T, High roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Panel Van - Medium Wheelbase
Panel Van | Technical Drawings20
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/5000
907653 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,9
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176720
laden unladen2422
473N/A
173594
2300
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/5000
907653 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,4
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176718
laden unladen2710
472N/A
173594
2590
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/5000
907653 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,9
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176720
laden unladen2422
473N/A
173594
2300
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/5000
907653 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,4
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176718
laden unladen2710
472N/A
173594
2590
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/5000
907653 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,9
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176720
laden unladen2422
473N/A
173594
2300
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/5000
907653 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,4
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176718
laden unladen2710
472N/A
173594
2590
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH1/RWD 4x2/5000
907653 12.12.2019
D93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A8,9
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176720
laden unladen2422
473N/A
173594
2300
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA2LH2/RWD 4x2/5000
907653 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A10,4
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176718
laden unladen2710
472N/A
173594
2590
406N/A
4,741
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49 and 5T, Standard roof
RWD, 4.49 and 5T, High roof
Technical Drawings Panel Van - Medium Wheelbase
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Panel Van | Technical Drawings 21
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Panel Van - Long Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/3500
907635 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2616
398N/A
158521
2519
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/3500
907635 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2831
397N/A
158521
2742
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/3500
907635 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2616
398N/A
158521
2519
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/3500
907635 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2831
397N/A
158521
2742
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/3500
907635 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2616
398N/A
158521
2519
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/3500
907635 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2831
397N/A
158521
2742
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/3500
907635 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2616
398N/A
158521
2519
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/3500
907635 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161621
laden unladen2831
397N/A
158521
2742
351N/A
6,9
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 3.55T, High roof
RWD, 3.55T, Super high roof
Panel Van | Technical Drawings22
Technical Drawings Panel Van - Long Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/4100
907645 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2663
438N/A
160561
2558
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/4100
907645 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2878
437N/A
160561
2779
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/4100
907645 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2663
438N/A
160561
2558
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/4100
907645 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2878
437N/A
160561
2779
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/4100
907645 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2663
438N/A
160561
2558
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/4100
907645 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2878
437N/A
160561
2779
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/4100
907645 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A14
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2663
438N/A
160561
2558
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/4100
907645 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
163669
laden unladen2878
437N/A
160561
2779
374N/A
6,9
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.1T, High roof
RWD, 4.1T, Super high roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Panel Van | Technical Drawings 23
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/5000
907655 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A13,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176713
laden unladen2706
462N/A
173595
2595
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/5000
907655 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176712
laden unladen2917
461N/A
173595
2812
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/5000
907655 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A13,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176713
laden unladen2706
462N/A
173595
2595
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/5000
907655 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176712
laden unladen2917
461N/A
173595
2812
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/5000
907655 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A13,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176713
laden unladen2706
462N/A
173595
2595
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/5000
907655 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176712
laden unladen2917
461N/A
173595
2812
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH2/RWD 4x2/5000
907655 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A13,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176713
laden unladen2706
462N/A
173595
2595
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA3LH3/RWD 4x2/5000
907655 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176712
laden unladen2917
461N/A
173595
2812
405N/A
6,552
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49 and 5T, High roof
RWD, 4.49 and 5T, Super high roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Panel Van - Long Wheelbase
Panel Van | Technical Drawings24
Technical Drawings Panel Van - Extra Long Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/3500
907637 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162617
laden unladen2613
399N/A
158522
2521
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/3500
907637 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161617
laden unladen2825
399N/A
158522
2737
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/3500
907637 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162617
laden unladen2613
399N/A
158522
2521
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/3500
907637 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161617
laden unladen2825
399N/A
158522
2737
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/3500
907637 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162617
laden unladen2613
399N/A
158522
2521
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/3500
907637 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161617
laden unladen2825
399N/A
158522
2737
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/3500
907637 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162617
laden unladen2613
399N/A
158522
2521
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/3500
907637 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602250
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
161617
laden unladen2825
399N/A
158522
2737
351N/A
7,606
3500
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 3.55T, High roof
RWD, 3.55T, Super high roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Panel Van | Technical Drawings 25
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/4100
907647 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162667
laden unladen2662
439N/A
160564
2561
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/4100
907647 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162666
laden unladen2873
439N/A
160564
2776
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/4100
907647 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162667
laden unladen2662
439N/A
160564
2561
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/4100
907647 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162666
laden unladen2873
439N/A
160564
2776
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/4100
907647 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162667
laden unladen2662
439N/A
160564
2561
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/4100
907647 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162666
laden unladen2873
439N/A
160564
2776
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/4100
907647 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,5
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162667
laden unladen2662
439N/A
160564
2561
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/4100
907647 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A17
14,4N/A
18602430
Optional equipment: Important notes:
Front axleRear axle
235/65 R16CBase tyres:
235/65 R16C
162666
laden unladen2873
439N/A
160564
2776
374N/A
7,606
4100
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.1T, High roof
RWD, 4.1T, Super high roof
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Panel Van - Extra Long Wheelbase
Panel Van | Technical Drawings26
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/5000
907657 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176709
laden unladen2703
464N/A
173598
2596
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/5000
907657 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A16,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176708
laden unladen2912
464N/A
173598
2810
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/5000
907657 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176709
laden unladen2703
464N/A
173598
2596
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/5000
907657 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A16,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176708
laden unladen2912
464N/A
173598
2810
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/5000
907657 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176709
laden unladen2703
464N/A
173598
2596
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/5000
907657 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A16,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176708
laden unladen2912
464N/A
173598
2810
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH2/RWD 4x2/5000
907657 12.12.2019
D03 high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A15,4
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176709
laden unladen2703
464N/A
173598
2596
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Panel vanA4LH3/RWD 4x2/5000
907657 12.12.2019
D05 super-high roofD93 omission of partitionMP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatT19 sliding door, leftT93 loading compartment sliding door deletedXZ0 model generation
N/A16,9
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176708
laden unladen2912
464N/A
173598
2810
405N/A
7,273
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49, High roof
RWD, 4.49, Super high roof
Technical Drawings Panel Van - Extra Long Wheelbase
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Cab Chassis | Technical Drawings 27
RWD, 4.49 and 5T, without tray
RWD, 4.49 and 5T, with tray
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176831
laden unladen2360
471N/A
173669
2273
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761024
laden unladen2348
471N/A
173890
2273
406N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176831
laden unladen2360
471N/A
173669
2273
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761024
laden unladen2348
471N/A
173890
2273
406N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176831
laden unladen2360
471N/A
173669
2273
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761024
laden unladen2348
471N/A
173890
2273
406N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176831
laden unladen2360
471N/A
173669
2273
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA2LH1/RWD 4x2/5000
907153 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761024
laden unladen2348
471N/A
173890
2273
406N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Cab Chassis - Medium Wheelbase
Cab Chassis | Technical Drawings28
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176827
laden unladen2351
461N/A
173668
2271
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2337
461N/A
173889
2271
405N/A
9,198
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176827
laden unladen2351
461N/A
173668
2271
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2337
461N/A
173889
2271
405N/A
9,198
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176827
laden unladen2351
461N/A
173668
2271
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2337
461N/A
173889
2271
405N/A
9,198
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
ChassisA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176827
laden unladen2351
461N/A
173668
2271
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Single cab with loading platformA3LH1/RWD 4x2/5000
907155 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS23 two-seater passenger seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2337
461N/A
173889
2271
405N/A
9,198
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49 and 5T, without tray
RWD, 4.49 and 5T, with tray
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Technical Drawings Cab Chassis - Long Wheelbase
Dual Cab Chassis | Technical Drawings 29
Technical Drawings Dual Cab Chassis - Medium Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2358
464N/A
173669
2267
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2345
464N/A
173891
2267
406N/A
5,782
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2358
464N/A
173669
2267
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2345
464N/A
173891
2267
406N/A
5,782
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2358
464N/A
173669
2267
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2345
464N/A
173891
2267
406N/A
5,782
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2358
464N/A
173669
2267
406N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA2LH1/RWD 4x2/5000
907253 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
12,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761019
laden unladen2345
464N/A
173891
2267
406N/A
5,782
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49 and 5T, without tray
RWD, 4.49 and 5T, with tray
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
Dual Cab Chassis | Technical Drawings30
Technical Drawings Dual Cab Chassis - Long Wheelbase
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2345
455N/A
173668
2264
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761015
laden unladen2332
455N/A
173890
2264
405N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2345
455N/A
173668
2264
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761015
laden unladen2332
455N/A
173890
2264
405N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2345
455N/A
173668
2264
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761015
laden unladen2332
455N/A
173890
2264
405N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Crew cabA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
176821
laden unladen2345
455N/A
173668
2264
405N/A
N/A
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
We reserve all rights for this drawing. The drawing may neither be copied nor passed on to any third person. Dimensions are subject to a tolerance of up to +/- 3%.
- It is the responsibility of the bodybuilder to ensure that the vehicle is suitable for homologation after the body has been mounted.
- The drawing is simplified to some extent and is not legally binding.- Please check whether the drawing specification complies with the chassis
configuration of your order.- Optional equipment codes not listed here, KW-codes and changes resulting
from feasibility checks are not included in the drawing.- Our instructions for the manufacture of superstructures must be observed,
when planning to fit bodies of other than Mercedes-Benz manufacture.
All dimensions refer to the standard version and the base tyres.In laden condition all axles are fully loaded (see table).
Double cab with loading platformA3LH1/RWD 4x2/5000
907255 12.12.2019
MP6 engine version Euro VIP02 steel loading platform with aluminium wallsS02 driver seatS04 adjustable co-drivers seatXZ0 model generation
N/AN/A
14,3N/A
18503500
Optional equipment: Important notes:
Front axleRear axle
195/75 R16CBase tyres:
195/75 R16C
1761015
laden unladen2332
455N/A
173890
2264
405N/A
7,703
5000
Cargo volume [m³]Cargo area [m²]
Gross vehicle weight [kg]
Luggage volume [l]
Dimensions & weights:
Permissable front axle load [kg]Permissable rear axle load [kg]
Luggage area [m²]
Turning clearance circle - curb to curb [m]
Minimal ground clearance [mm]Rear lift in height [mm]
Vehicle height [mm]
Driver‘s door step height [mm]Side cargo step height [mm]
RWD, 4.49 and 5T, without tray
RWD, 4.49 and 5T, with tray
Note: Drawings are general arrangement drawings only and should not relay upon. Contact your local dealer if you require more specific information.
IMPORTANT! This brochure has been compiled by Mercedes-Benz Australia/Pacific Pty Ltd to provide a general indication of the models available in Australia. Some of the features, optional extras and/or colours shown may not be available in Australia or may only be available in a different specification. Additionally, some models, features, optional extras and/or colours may only be available in combination with others. Some equipment depicted either on vehicle illustrations or separately may be non standard or options and may, where applicable, be available at an additional cost. For current information on the availability, design features and prices of all models, features, optional extras and/or colours available in Australia, you should contact your authorised Mercedes-Benz Vans Dealer at www.mercedes-benz.com.au/dealers or go to www.mercedes-benz.com.au/vans
All of the information contained in this brochure was correct as at January 2020. However, the manufacturer reserves the right to discontinue, make changes to design and specifications to vehicles or optional equipment without notice. The and the words Mercedes-Benz are registered trademarks of Daimler AG, Stuttgart, Germany.
Mercedes-Benz Australia/Pacific Pty Ltd, ABN 16 618 413 362. Lexia Place, Mulgrave, Victoria 3170. Telephone: (03) 9566 9266. Facsimile: (03) 9562 6282.