Post on 23-Apr-2022
Burr-Brown Audio
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
™ Low Noise and Distortion, General-Purpose, FET-InputAUDIO OPERATIONAL AMPLIFIERS
Check for Samples: OPA1652, OPA1654
1FEATURES DESCRIPTIONThe OPA1652 (dual) and OPA1654 (quad) FET-input
234• Low Noise: 4.5 nV/√Hz at 1 kHzoperational amplifiers achieve a low 4.5 nV/√Hz noise• Low Distortion: 0.00005% at 1 kHz density with an ultralow distortion of 0.00005% at 1
• Low Quiescent Current: kHz. The OPA1652 and OPA1654 op amps offer2 mA Per Channel rail-to-rail output swing to within 800 mV with 2-kΩ
load, which increases headroom and maximizes• Low Input Bias Current: 10 pAdynamic range. These devices also have a high• Slew Rate: 10 V/μs output drive capability of ±30 mA.
• Wide Gain Bandwidth: 18 MHz (G = +1)These devices operate over a very wide supply range
• Unity Gain Stable of ±2.25 V to ±18 V, or +4.5 V to +36 V, on only 2 mA• Rail-to-Rail Output of supply current per channel. The OPA1652 and
OPA1654 op amps are unity-gain stable and provide• Wide Supply Range:excellent dynamic behavior over a wide range of load±2.25 V to ±18 V, or +4.5 V to +36 Vconditions.
• Dual and Quad Versions AvailableThese devices also feature completely independent• Small Package Sizes:circuitry for lowest crosstalk and freedom fromDUAL: SO-8 and MSOP-8 interactions between channels, even when overdriven
QUAD: SO-14 and TSSOP-14 or overloaded.
The OPA1652 and OPA1654 temperature ranges areAPPLICATIONSspecified from –40°C to +85°C. SoundPlus™
• Analog and Digital Mixers• Audio Effects Processors• Musical Instruments• A/V Receivers• DVD and Blu-Ray™ Players• Car Audio Systems
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2SoundPlus is a trademark of Texas Instruments Incorporated.3Blu-Ray is a trademark of Blu-Ray Disc Association.4All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2011, Texas Instruments IncorporatedProducts conform to specifications per the terms of the TexasInstruments standard warranty. Production processing does notnecessarily include testing of all parameters.
1
2
3
4
8
7
6
5
V+
OUT B
-IN B
+IN B
OUT A
-IN A
+IN A
V-
A
B
Out A
-In A
+In A
V+
+ In B
-In B
Out B
1
2
3
4
5
6
7
14
13
12
11
10
9
8
DA
B C
Out D
-In D
+In D
V-
+ In C
-In C
Out C
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled withappropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be moresusceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE INFORMATION (1)
PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR PACKAGE MARKING
SO-8 D OP1652OPA1652
MSOP-8 DGK OUPI
SO-14 D OP1654OPA1654
TSSOP-14 PW OP1654
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TIweb site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range (unless otherwise noted).
OPA1652, OPA1654 UNIT
Supply Voltage VS = (V+) – (V–) 40 V
Input Voltage (V–) – 0.5 to (V+) + 0.5 V
Input Current (All pins except power-supply pins) ±10 mA
Output Short-Circuit (2) Continuous
Operating Temperature –55 to +125 °CStorage Temperature –65 to +150 °CJunction Temperature 200 °C
Human Body Model (HBM) 2 kV
ESD Ratings Charged Device Model (CDM) 1 kV
Machine Model (MM) 200 V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods maydegrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyondthose specified is not supported.
(2) Short-circuit to VS/2 (ground in symmetrical dual supply setups), one amplifier per package.
PIN CONFIGURATIONS
OPA1652: D AND DGK PACKAGESOPA1654: D AND PW PACAKGESSO-8 AND MSOP-8
SO-14 AND TSSOP-14(TOP VIEW)(TOP VIEW)
2 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
ELECTRICAL CHARACTERISTICS: VS = ±15 VAt TA = +25°C, RL = 2 kΩ, and VCM = VOUT = midsupply, unless otherwise noted.
OPA1652, OPA1654
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
AUDIO PERFORMANCE
0.00005 %THD+N Total harmonic distortion + noise
G = +1, f = 1 kHz, VO = 3 VRMS –126 dB
0.00005 %SMPTE/DIN Two-Tone, 4:1(60 Hz and 7 kHz) –126 dB
0.00005 %G = +1, DIM 30 (3-kHz square waveIMD Intermodulation distortion VO = 3 VRMS and 15-kHz sine wave) –126 dB
0.00005 %CCIF Twin-Tone(19 kHz and 20 kHz) –126 dB
FREQUENCY RESPONSE
GBW Gain-bandwidth product G = +1 18 MHz
SR Slew rate G = –1 10 V/μs
Full power bandwidth (1) VO = 1 VP 1.6 MHz
Overload recovery time G = –10 1 μs
Channel separation (dual and quad) f = 1 kHz –120 dB
NOISE
en Input voltage noise f = 20 Hz to 20 kHz 5.4 μVPP
Input voltage noise density f = 1 kHz 4.5 nV/√Hz
In Input current noise density f = 1 kHz 0.5 pA/√Hz
OFFSET VOLTAGE
VS = ±2.25 V to ±18 V ±0.5 ±1.5 mVVOS Input offset voltage
VS = ±2.25 V to ±18 V, TA = –40°C to +85°C (2) 2 8 μV/°C
PSRR Power-supply rejection ratio VS = ±2..25 V to ±18 V 3 8 μV/V
INPUT BIAS CURRENT
IB Input bias current VCM = 0 V ±10 ±100 pA
IOS Input offset current VCM = 0 V ±10 ±100 pA
INPUT VOLTAGE RANGE
VCM Common-mode voltage range (V–) + 0.5 (V+) – 2 V
CMRR Common-mode rejection ratio 100 110 dB
INPUT IMPEDANCE
Differential 100 || 6 MΩ || pF
Common-mode 6000 || 2 GΩ || pF
OPEN-LOOP GAIN
AOL Open-loop voltage gain (V–) + 0.8 V ≤ VO ≤ (V+) – 0.8 V, RL = 2 kΩ 106 114 dB
OUTPUT
VOUT Voltage output RL = 2 kΩ (V–) + 0.8 (V+) – 0.8 V
IOUT Output current See Typical Characteristics mA
ZO Open-loop output impedance f = 1 MHz See Typical Characteristics Ω
ISC Short-circuit current (3) ±50 mA
CLOAD Capacitive load drive 100 pF
POWER SUPPLY
VS Specified voltage ±2.25 ±18 V
IOUT = 0 A 2.0 2.5 mAQuiescent currentIQ (per channel) IOUT = 0 A, TA = –40°C to +85°C (2) 2.8 mA
(1) Full-power bandwidth = SR/(2π × VP), where SR = slew rate.(2) Specified by design and characterization.(3) One channel at a time.
Copyright © 2011, Texas Instruments Incorporated 3
Product Folder Link(s): OPA1652 OPA1654
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
ELECTRICAL CHARACTERISTICS: VS = ±15 V (continued)At TA = +25°C, RL = 2 kΩ, and VCM = VOUT = midsupply, unless otherwise noted.
OPA1652, OPA1654
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TEMPERATURE
Specified range –40 +85 °C
Operating range –55 +125 °C
THERMAL INFORMATION: OPA1652OPA1652
THERMAL METRIC (1) D (SO) DGK (MSOP) UNITS
8 PINS 8 PINS
θJA Junction-to-ambient thermal resistance 143.6 218.9
θJCtop Junction-to-case (top) thermal resistance 76.9 78.6
θJB Junction-to-board thermal resistance 61.8 103.7°C/W
ψJT Junction-to-top characterization parameter 27.8 14.6
ψJB Junction-to-board characterization parameter 61.3 101.8
θJCbot Junction-to-case (bottom) thermal resistance N/A N/A
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
THERMAL INFORMATION: OPA1654OPA1654
THERMAL METRIC (1) D (SO) PW (TSSOP) UNITS
14 PINS 14 PINS
θJA Junction-to-ambient thermal resistance 90.1 126.9
θJCtop Junction-to-case (top) thermal resistance 54.8 46.6
θJB Junction-to-board thermal resistance 44.4 58.6°C/W
ψJT Junction-to-top characterization parameter 19.9 5.5
ψJB Junction-to-board characterization parameter 44.2 57.8
θJCbot Junction-to-case (bottom) thermal resistance N/A N/A
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
Time (1 s/div)
Voltage N
ois
e (
500 n
V/d
iv)
G002
1
10
100
1 10 100 1k 10k 100kFrequency (Hz)
Vol
tage
Noi
se (n
V/
Hz
)
G001
0
2
5
8
10
12
15
18
20
10k 100k 1M 10MFrequency (Hz)
Out
put V
olta
ge (
V)
VS = ± 15 V
VS = ± 2.25 V
G004
1
10
100
1k
10k
100 1k 10k 100k 1M
Resistor Noise
OPA166x
OPA165x
Source Resistance ( )W
Voltage N
ois
e (nV
/H
z)
Eo
2= e
n
2+ (inRS)
2+ 4KTRS
G003
RS
EO
10 100 1k 10k 100k 1M 10M 100M−20
0
20
40
60
80
100
120
140
0
45
90
135
180
Frequency (Hz)
Gai
n (d
B)
Pha
se (
°)
GainPhase
CL = 10 pF
G005
−20
0
20
40
100k 1M 10M 100MFrequency (Hz)
Gai
n (d
B)
Gain = −1 V/VGain = +1 V/VGain = +10 V/V
CL = 10 pF
G006
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
TYPICAL CHARACTERISTICSAt TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
INPUT VOLTAGE NOISE DENSITYvs FREQUENCY 0.1Hz TO 10Hz NOISE
Figure 1. Figure 2.
VOLTAGE NOISE vs SOURCE RESISTANCE MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
Figure 3. Figure 4.
GAIN AND PHASE vs FREQUENCY CLOSED-LOOP GAIN vs FREQUENCY
Figure 5. Figure 6.
Copyright © 2011, Texas Instruments Incorporated 5
Product Folder Link(s): OPA1652 OPA1654
0.00001
0.0001
0.001
0.01
20 100 1k 10k 20kFrequency (Hz)
TH
D+
N (
%)
G = 10 V/V, RL = 600 ΩG = 10 V/V, RL = 2 kΩG = +1 V/V, RL = 600 ΩG = +1 V/V, RL = 2 kΩG = −1 V/V, RL = 600 ΩG = −1 V/V, RL = 2 kΩ
VOUT = 3 VRMS
BW = 80 kHz
G007
0.00001
0.0001
0.001
0.01
20 100 1k 10k 20k
Frequency (Hz)
TH
D+
N (
%)
RS = 0 W
RS = 30 W
RS = 60 W
RS = 1 kW
VOUT = 3 VRMS
BW = 80 kHz
G008
OPA1652
+15V
-15V RL
RSOURCE
0.00001
0.0001
0.001
0.01
20 100 1k 10k 100kFrequency (Hz)
TH
D+
N (
%)
G = 10 V/V, RL = 600 ΩG = 10 V/V, RL = 2 kΩG = +1 V/V, RL = 600 ΩG = +1 V/V, RL = 2 kΩG = −1 V/V, RL = 600 ΩG = −1 V/V, RL = 2 kΩ
VOUT = 3 VRMS
BW = 500 kHz
G009
0.00001
0.0001
0.001
0.01
20 100 1k 10k 100k
Frequency (Hz)
TH
D+
N (
%)
RS = 0 W
RS = 30 W
RS = 60 W
RS = 1 kW
VOUT = 3 VRMS
BW = 500 kHz
G010
OPA1652
+15V
-15V RL
RSOURCE
0.00001
0.0001
0.001
0.01
1m 10m 100m 1 10 20Output Amplitude (Vrms)
TH
D+
N (
%)
G = 10 V/V, RL = 600 ΩG = 10 V/V, RL = 2 kΩG = +1 V/V, RL = 600 ΩG = +1 V/V, RL = 2 kΩG = −1 V/V, RL = 600 ΩG = −1 V/V, RL = 2 kΩ
f = 1 kHzBW = 80 kHzRS = 0 Ω
G011
0.00001
0.0001
0.001
0.01
100m 1 10 20Output Amplitude (Vrms)
TH
D+
N (
%)
DIM 30: 3 kHz − Square Wave, 15 kHz Sine WaveCCIF Twin Tone: 19 kHz and 20 kHzSMPTE / DIN: Two −Tone 4:1, 60 Hz and 7 KHz
G = +1 V/V
G012
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
TYPICAL CHARACTERISTICS (continued)At TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
THD+N RATIO vs FREQUENCY THD+N RATIO vs FREQUENCY
Figure 7. Figure 8.
THD+N RATIO vs FREQUENCY THD+N RATIO vs FREQUENCY
Figure 9. Figure 10.
INTERMODULATION DISTORTION vsTHD+N RATIO vs OUTPUT AMPLITUDE OUTPUT AMPLITUDE
Figure 11. Figure 12.
6 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
−160
−140
−120
−100
−80
100 1k 10k 100kFrequency (Hz)
Cro
ssta
lk (
dB)
VOUT = 3 VRMS
Gain = +1 V/V
G013
0
20
40
60
80
100
120
140
100 1k 10k 100k 1M 10M 100MFrequency (Hz)
CM
RR
, PS
RR
(dB
)
+PSRR−PSRRCMRR
G014
Time (0.2 s/div)m
Voltage (
25 m
V/d
iv)
VIN
VOUT
G = +1 V/VCL = 100 pF
G015 Time (0.2 s/div)m
Voltage (
25 m
V/d
iv)
VIN
VOUT
G = −1 V/VCL = 100 pF
G016
Time (1 s/div)m
Voltage (
2.5
V/d
iv)
VIN
VOUT
G = + 1V/VRF = 2 kW
CL = 100 pF
G017 Time (1 s/div)m
Voltage (
2.5
V/d
iv)
VIN
VOUT
G018
G = −1 V/VCL = 100 pF
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)At TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
CHANNEL SEPARATION vs FREQUENCY CMRR AND PSRR vs FREQUENCY (Referred to Input)
Figure 13. Figure 14.
SMALL-SIGNAL STEP RESPONSE SMALL-SIGNAL STEP RESPONSE(100mV) (100mV)
Figure 15. Figure 16.
LARGE-SIGNAL STEP RESPONSE LARGE-SIGNAL STEP RESPONSE
Figure 17. Figure 18.
Copyright © 2011, Texas Instruments Incorporated 7
Product Folder Link(s): OPA1652 OPA1654
0
5
10
15
20
25
30
35
40
45
50
0 50 100 150 200 250 300 350 400
Capacitance (pF)
Ove
rsh
oo
t (%
)
RS = 0 W
RS = 25 W
RS = 50 W
VOUT = 100 mVPP
G = +1 V/V
G019
+15 V
-15 V
RS
CL
OPA1652
RL
0
5
10
15
20
25
30
35
40
45
50
0 50 100 150 200 250 300 350 400
Capacitance (pF)
Ove
rsh
oo
t (%
)
RS = 0 W
RS = 25 W
RS = 50 W
VOUT = 100 mVPP
G = −1 V/V
G020
OPA1652
R =I 2 kW
RS
CL
RF = 2 kW
+15 V
-15 V
−1
0
1
2
3
4
−40 −15 10 35 60 85 110 135Temperature (°C)
AO
L (µ
V)
RL = 2 kΩ
G022
0
5
10
15
20
25
0 1 2 3 4 5
Capacitance (pF)
Overs
hoot (%
)
VOUT = 100 mVPP
G = −1 V/VRS = 0 W
G021
OPA1652
R =I 2 kW
RS
CL
CF
RF = 2 kW
+15 V
-15 V
−2000
−1600
−1200
−800
−400
0
400
800
1200
−40 −15 10 35 60 85 110 135Temperature (°C)
Ib a
nd Io
s C
urre
nt (
pA)
IbnIbp
Ios
G023
−8
−6
−4
−2
0
2
4
6
8
−18 −15 −12 −9 −6 −3 0 3 6 9 12 15 18Common − Mode Voltage (V)
Ib a
nd Io
s C
urre
nt (
pA)
Ibp
IbnIos
G024
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
TYPICAL CHARACTERISTICS (continued)At TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
SMALL-SIGNAL OVERSHOOT SMALL-SIGNAL OVERSHOOTvs CAPACITIVE LOAD vs CAPACITIVE LOAD
Figure 19. Figure 20.
SMALL-SIGNAL OVERSHOOTvs FEEDBACK CAPACITOR (100mV Output Step) OPEN-LOOP GAIN vs TEMPERATURE
Figure 21. Figure 22.
IB AND IOS vs TEMPERATURE IB AND IOS vs COMMON-MODE VOLTAGE
Figure 23. Figure 24.
8 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
0
0.5
1
1.5
2
2.5
3
−40 −15 10 35 60 85 110 135Temperature (°C)
Sup
ply
Cur
rent
(m
A)
G025
0
0.5
1
1.5
2
2.5
3
0 4 8 12 16 20 24 28 32 36Supply Voltage (V)
Sup
ply
Cur
rent
(m
A)
G026
−40
−30
−20
−10
0
10
20
30
40
0 5 10 15 20 25 30 35 40 45 50 55 60Output Current (mA)
Out
put V
olag
e S
win
g (V
)
−40 C−25 C0 C25 C85 C125 C
G029
−100
−80
−60
−40
−20
0
20
40
60
80
100
−40 −15 10 35 60 85 110 135Temperature (°C)
Isc
(mA
)
+Isc−Isc
G028
0
10
20
30
40
50
60
70
80
90
0 50 100 150 200 250 300 350 400Capacitance (pF)
Pha
se M
argi
n (°
)
G = +1 V/V
G031
0
10
20
30
40
50
0 50 100 150 200 250 300 350 400Capacitance (pF)
Ove
rsho
ot (
%)
VS = ± 2.25 VVS = ± 18 V
G = +1 V/VVIN = 100 mVPP
G032
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
TYPICAL CHARACTERISTICS (continued)At TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
SUPPLY CURRENT vs TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE
Figure 25. Figure 26.
OUTPUT VOLTAGE vs OUTPUT CURRENT SHORT-CIRCUIT CURRENT vs TEMPERATURE
Figure 27. Figure 28.
PHASE MARGIN vs CAPACITIVE LOAD PERCENT OVERSHOOT vs CAPACITIVE LOAD
Figure 29. Figure 30.
Copyright © 2011, Texas Instruments Incorporated 9
Product Folder Link(s): OPA1652 OPA1654
Time (0.4 s/div)m
Ou
tpu
t V
olta
ge
(5
V/d
iv)
VIN
VOUT
G = −10 V/V
G033
2 kW
20 kW
VIN
VOUTOPA1652
G = 10-
+18 V
-18 V
Time (0.4 s/div)m
Outp
ut V
oltage (
5 V
/div
)
VIN
VOUT
G = −10 V/V
G027
2 kW
20 kW
VIN
VOUTOPA1652
G = 10-
+18 V
-18 V
G = +1 V/V
−20
−15
−10
−5
0
5
10
15
20
Time (125 s/div)m
Vo
lta
ge
(V
)
VIN
VOUT
G034
+18 V
-18 V
37VPP
Sine Wave
( 18.5 V)±
OPA1652
10
100
1k
10 100 1k 10k 100k 1M 10M 100MFrequency (Hz)
Impe
danc
e (Ω
)
G030
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
TYPICAL CHARACTERISTICS (continued)At TA = +25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
NEGATIVE OVERLOAD RECOVERY POSITIVE OVERLOAD RECOVERY
Figure 31. Figure 32.
OPEN-LOOP OUTPUT IMPEDANCE vsFREQUENCY NO PHASE REVERSAL
Figure 33. Figure 34.
10 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
VBIAS1
Class AB
Control
Circuitry
VBIAS2
V +IN
V+
V-
V -IN
VO
TailCurrent
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
APPLICATION INFORMATION
applications do not require equal positive andThe OPA1652 and OPA1654 are unity-gain stable, negative output voltage swing. With the OPA165xprecision dual and quad op amps with very low noise. series, power-supply voltages do not need to beApplications with noisy or high-impedance power equal. For example, the positive supply could be setsupplies require decoupling capacitors close to the to +25 V with the negative supply at –5 V.device pins. In most cases, 0.1-μF capacitors areadequate. Figure 35 shows a simplified schematic of In all cases, the common-mode voltage must bethe OPA165x (one channel shown). maintained within the specified range. In addition, key
parameters are assured over the specifiedtemperature range of TA = –40°C to +85°C.OPERATING VOLTAGEParameters that vary significantly with operating
The OPA165x series op amps operate from ±2.25 V voltage or temperature are shown in the Typicalto ±18 V supplies while maintaining excellent Characteristics.performance. The OPA165x series can operate withas little as +4.5V between the supplies and with up to+36 V between the supplies. However, some
Figure 35. OPA165x Simplified Schematic
Copyright © 2011, Texas Instruments Incorporated 11
Product Folder Link(s): OPA1652 OPA1654
1
10
100
1k
10k
100 1k 10k 100k 1M
Resistor Noise
OPA166X
OPA165X
Source Resistance (Ω)
Vol
tage
Noi
se (n
V/
Hz
)
Eo2 = en
2 + (inRS)2 + 4KTRS
G003
OPA165x Output
RF
Input
-
+RI
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
INPUT PROTECTION The equation in Figure 37 shows the calculation ofthe total circuit noise, with these parameters:
The input terminals of the OPA1652 and OPA1654• en = Voltage noiseare protected from excessive differential voltage with• in = Current noiseback-to-back diodes, as Figure 36 illustrates. In most
circuit applications, the input protection circuitry has • RS = Source impedanceno consequence. However, in low-gain or G = +1 • k = Boltzmann’s constant = 1.38 × 10–23 J/Kcircuits, fast ramping input signals can forward bias • T = Temperature in Kelvins (K)these diodes because the output of the amplifiercannot respond rapidly enough to the input ramp. Ifthe input signal is fast enough to create this forwardbias condition, the input signal current must be limitedto 10 mA or less. If the input signal current is notinherently limited, an input series resistor (RI) and/ora feedback resistor (RF) can be used to limit thesignal input current. This resistor degrades thelow-noise performance of the OPA165x and isexamined in the following Noise Performance section.Figure 36 shows an example configuration when bothcurrent-limiting input and feeback resistors are used.
Figure 37. Noise Performance of the OPA165x inUnity-Gain Buffer Configuration
BASIC NOISE CALCULATIONS
Design of low-noise op amp circuits requires carefulconsideration of a variety of possible noisecontributors: noise from the signal source, noisegenerated in the op amp, and noise from theFigure 36. Pulsed Operationfeedback network resistors. The total noise of thecircuit is the root-sum-square combination of all noisecomponents.NOISE PERFORMANCE
The resistive portion of the source impedanceFigure 37 shows the total circuit noise for varyingproduces thermal noise proportional to the squaresource impedances with the op amp in a unity-gainroot of the resistance. Figure 37 plots this equation.configuration (no feedback resistor network, andThe source impedance is usually fixed; consequently,therefore no additional noise contributions).select the op amp and the feedback resistors to
The OPA165x (GBW = 18 MHz, G = +1) is shown minimize the respective contributions to the totalwith total circuit noise calculated. The op amp itself noise.contributes both a voltage noise component and a
Figure 38 illustrates both inverting and noninvertingcurrent noise component. The voltage noise isop amp circuit configurations with gain. In circuitcommonly modeled as a time-varying component ofconfigurations with gain, the feedback networkthe offset voltage. The current noise is modeled asresistors also contribute noise. The current noise ofthe time-varying component of the input bias currentthe op amp reacts with the feedback resistors toand reacts with the source resistance to create acreate additional noise components. The feedbackvoltage component of noise. Therefore, the lowestresistor values can generally be chosen to makenoise op amp for a given application depends on thethese noise sources negligible. The equations forsource impedance. For low source impedance,total noise are shown for both configurations.current noise is negligible, and voltage noise
generally dominates. The voltage noise of theOPA165x series op amps makes them a betterchoice for source impedances greater than or equalto 1 kΩ.
12 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
R1
R2
EO
R1
R2
EOR
S
VS
RS
VS
A) Noise in Noninverting Gain Configuration
B) Noise in Inverting Gain Configuration
Noise at the output:
Where e =S
4kTRS
4kTR1
4kTR2
= thermal noise of RS
= thermal noise of R1
= thermal noise of R2
e =1
e =2
Noise at the output:
E =O
21 +
R2
R + R1 S
R2
R + R1 S
2 22
Where e =S
4kTRS
4kTR1
4kTR2
= thermal noise of RS
= thermal noise of R1
= thermal noise of R2
e =1
e =2
R2
R + R1 S
2
1 +R
2
R1
1 +R
2
R1
2
R2
R1
2
e + e +1 2
2 2E =
O
2e +
n
2e
s
2
e + e +1 2
2 2e
s
2e +
n
2
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
Note: For the OPA165x series of op amps at 1kHz, en = 4.5nV/√Hz.
Figure 38. Noise Calculation in Gain Configurations
Copyright © 2011, Texas Instruments Incorporated 13
Product Folder Link(s): OPA1652 OPA1654
R2
OPA165x
R1
Signal Gain = 1+
Distortion Gain = 1+
R3 V = 3 VO RMS
GeneratorOutput
AnalyzerInput
Audio Precision
System Two(1)
with PC Controller
SIGNAL
GAIN
DISTORTION
GAIN R1
R2
R3
¥
4.99 kW
1 kW
4.99 kW
10 W
49.9 W
+1
-1
101
549 W 4.99 kW 49.9 W+10 110
101R2
R1
R2
R II R1 3
Load
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
TOTAL HARMONIC DISTORTION The validity of this technique can be verified byMEASUREMENTS duplicating measurements at high gain and/or high
frequency where the distortion is within theThe OPA165x series op amps have excellent measurement capability of the test equipment.distortion characteristics. THD + noise is below Measurements for this data sheet were made with an0.0002% (G = +1, VO = 3 VRMS, BW = 80 kHz) Audio Precision System Two distortion/noisethroughout the audio frequency range, 20 Hz to 20 analyzer, which greatly simplifies such repetitivekHz, with a 2-kΩ load (see Figure 7 for characteristic measurements. The measurement technique can,performance). however, be performed with manual distortion
measurement instruments.The distortion produced by the OPA165x series opamps is below the measurement limit of manycommercially available distortion analyzers. However, CAPACITIVE LOADSa special test circuit (such as Figure 39 shows) can
The dynamic characteristics of the OPA1652 andbe used to extend the measurement capabilities.OPA1654 have been optimized for commonly
Op amp distortion can be considered an internal error encountered gains, loads, and operating conditions.source that can be referred to the input. Figure 39 The combination of low closed-loop gain and highshows a circuit that causes the op amp distortion to capacitive loads decreases the phase margin of thebe gained up (refer to the table in Figure 39 for the amplifier and can lead to gain peaking or oscillations.distortion gain factor for various signal gains). The As a result, heavier capacitive loads must be isolatedaddition of R3 to the otherwise standard noninverting from the output. The simplest way to achieve thisamplifier configuration alters the feedback factor or isolation is to add a small resistor (RS equal to 50 Ω,noise gain of the circuit. The closed-loop gain is for example) in series with the output.unchanged, but the feedback available for error
This small series resistor also prevents excess powercorrection is reduced by the distortion gain factor,dissipation if the output of the device becomesthus extending the resolution by the same amount.shorted. Figure 19 illustrates a graph of Small-SignalNote that the input signal and load applied to the opOvershoot vs Capacitive Load for several values ofamp are the same as with conventional feedbackRS. Also, refer to Applications Bulletin AB-028without R3. The value of R3 should be kept small to(literature number SBOA015, available for downloadminimize its effect on the distortion measurements.from the TI web site) for details of analysistechniques and application circuits.
(1) For measurement bandwidth, see Figure 7 through Figure 12.
Figure 39. Distortion Test Circuit
14 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
5 kW
Device10 mA max
V+
VIN
VOUT
IOVERLOAD
OPA1652OPA1654
www.ti.com SBOS477 –DECEMBER 2011
POWER DISSIPATION
The OPA1652 and OPA1654 series op amps arecapable of driving 2-kΩ loads with a power-supplyvoltage up to ±18V and full operating temperaturerange. Internal power dissipation increases whenoperating at high supply voltages. Copper leadframeconstruction used in the OPA165x series op ampsimproves heat dissipation compared to conventionalmaterials. Circuit board layout can also help minimize Figure 40. Input Current Protectionjunction temperature rise. Wide copper traces helpdissipate the heat by acting as an additional heat An ESD event produces a short duration,sink. Temperature rise can be further minimized by high-voltage pulse that is transformed into a shortsoldering the devices to the circuit board rather than duration, high-current pulse as it discharges throughusing a socket. a semiconductor device. The ESD protection circuits
are designed to provide a current path around theELECTRICAL OVERSTRESS operational amplifier core to prevent it from beingdamaged. The energy absorbed by the protectionDesigners often ask questions about the capability ofcircuitry is then dissipated as heat.an operational amplifier to withstand electrical
overstress. These questions tend to focus on the When the operational amplifier connects into a circuit,device inputs, but may involve the supply voltage pins the ESD protection components are intended toor even the output pin. Each of these different pin remain inactive and not become involved in thefunctions have electrical stress limits determined by application circuit operation. However, circumstancesthe voltage breakdown characteristics of the may arise where an applied voltage exceeds theparticular semiconductor fabrication process and operating voltage range of a given pin. Should thisspecific circuits connected to the pin. Additionally, condition occur, there is a risk that some of theinternal electrostatic discharge (ESD) protection is internal ESD protection circuits may be biased on,built into these circuits to protect them from and conduct current. Any such current flow occursaccidental ESD events both before and during through ESD cells and rarely involves the absorptionproduct assembly. device.These ESD protection diodes also provide in-circuit, If there is an uncertainty about the ability of theinput overdrive protection, as long as the current is supply to absorb this current, external zener diodeslimited to 10 mA as stated in the Absolute Maximum may be added to the supply pins. The zener voltageRatings. Figure 40 shows how a series input resistor must be selected such that the diode does not turnmay be added to the driven input to limit the input on during normal operation.current. The added resistor contributes thermal noise
However, its zener voltage should be low enough soat the amplifier input and its value should be kept to athat the zener diode conducts if the supply pin beginsminimum in noise-sensitive applications.to rise above the safe operating supply voltage level.
Copyright © 2011, Texas Instruments Incorporated 15
Product Folder Link(s): OPA1652 OPA1654
I L+OUT
Audio DACwith Differential
CurrentOutputs
OPA165x
8200 pF
100 W
I L-OUT
OPA165x
0.1 Fm
2200 pF
820 W
0.1 Fm
2700 pF
-VA
( 15 V)-
+VA
(+15 V)
680 W 620 W
330 W
-VA
( 15 V)-
+VA
(+15 V)
0.1 Fm
0.1 Fm
330 W 2700 pFOPA165x
0.1 Fm
2200 pF
820 W
0.1 Fm
-VA
( 15 V)-
+VA
(+15 V) 680 W 620 W
L ChOutput
OPA1652OPA1654
SBOS477 –DECEMBER 2011 www.ti.com
APPLICATION CIRCUIT
An additional application idea is shown in Figure 41.
Figure 41. Audio DAC I/V Converter and Output Filter
16 Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s): OPA1652 OPA1654
PACKAGE OPTION ADDENDUM
www.ti.com 11-Apr-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status(1)
Package Type PackageDrawing
Pins PackageQty
Eco Plan(2)
Lead/Ball Finish MSL Peak Temp(3)
Op Temp (°C) Top-Side Markings(4)
Samples
OPA1652AID ACTIVE SOIC D 8 75 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OP1652
OPA1652AIDGK ACTIVE VSSOP DGK 8 80 Green (RoHS& no Sb/Br)
CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 OUPI
OPA1652AIDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAUAG Level-1-260C-UNLIM -40 to 85 OUPI
OPA1652AIDR ACTIVE SOIC D 8 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OP1652
OPA1654AID ACTIVE SOIC D 14 50 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA1654
OPA1654AIDR ACTIVE SOIC D 14 2500 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA1654
OPA1654AIPW ACTIVE TSSOP PW 14 90 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA1654
OPA1654AIPWR ACTIVE TSSOP PW 14 2000 Green (RoHS& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR -40 to 85 OPA1654
(1) The marketing status values are defined as follows:ACTIVE: Product device recommended for new designs.LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.PREVIEW: Device has been announced but is not in production. Samples may or may not be available.OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availabilityinformation and additional product content details.TBD: The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement thatlead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used betweenthe die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weightin homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 11-Apr-2013
Addendum-Page 2
(4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is acontinuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on informationprovided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken andcontinues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device PackageType
PackageDrawing
Pins SPQ ReelDiameter
(mm)
ReelWidth
W1 (mm)
A0(mm)
B0(mm)
K0(mm)
P1(mm)
W(mm)
Pin1Quadrant
OPA1652AIDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
OPA1652AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
OPA1654AIPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Apr-2013
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
OPA1652AIDGKR VSSOP DGK 8 2500 364.0 364.0 27.0
OPA1652AIDR SOIC D 8 2500 367.0 367.0 35.0
OPA1654AIPWR TSSOP PW 14 2000 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Apr-2013
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and otherchanges to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latestissue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of salesupplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s termsand conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessaryto support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarilyperformed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products andapplications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provideadequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, orother intellectual property right relating to any combination, machine, or process in which TI components or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty orendorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of thethird party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alterationand is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altereddocumentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or servicevoids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirementsconcerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or supportthat may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards whichanticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might causeharm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the useof any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is tohelp enable customers to design and create their own end-product solutions that meet applicable functional safety standards andrequirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the partieshave executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use inmilitary/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI componentswhich have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal andregulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use ofnon-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright © 2013, Texas Instruments Incorporated