RUTGERS INTELLIGENT TRANSPORTATION

SYSTEMS INSPECTION AND MAINTENANCE

SOFTWARE(RITSIMS)

03.12-13.200803.12-13.2008

NJDOT TRAINING CASE STUDY

Inspection for a CCTV:

1. Pre-Construction Electric Service

2. Service Poles and Electrical Feed

Inspection

• A new CCTV equipment is to be installed at I-287 Intersection on Route 1.

•It should be checked if it satisfies the inspection criteria.

Inspection

• The trainer checks the location and details of the camera at the office and consults his supervisor.

• With his laptop or tablet PC, and/or printed documents, he is ready to for the site inspection.

User Manual (How to Open RITSIMS?)

• Find the RITSIMS.exe on your desktop and just click on the application.

User Manual (How to Open RITSIMS?)

• As an alternative, locate the RITSIMS software folder.

• Find the MTSOFT.exe and just click on the application.

User Interface

User Manual (User Name and Password)

Select user1 as Username

Write 1234 for Password

User Manual (Starting the Applications)

Select “Start Inspection or Maintenance Applications”

User Manual (Equipment Selection)

Select “Closed Circuit

Television Systems”

User Manual (Option Selection)

Select “Inspection”

Option

User Manual (Location Selection)

Select EquipmentLocation

User Manual (Previous History Check)

As this is the first time

inspection, observe that there is no previous history.Click on “NEXT”

User Manual (Equipments)

Select “Preconstructi

on Electric Service”.Click on “START

APPLICATION”

User Manual (Questions)

Answer the eight

questions as instructed in

your handout

User Manual (Questions)

Then, click on “Next Component”

User Manual (Equipments)

Select “Service Poles and Electrical

Feed”.Click on “START

APPLICATION”

User Manual (Questions)

Answer the five

questions as instructed in

your handout

User Manual (Questions)

Click on “Exit” to see

the Final Report

User Manual (Inspection Report)

See the inspection report and

write comments if

needed!

User Manual (Inspection Report)

Change the “FAIL” answers

to “PASS”! When finished, click on “END”.

User Manual (Inspection Report)

Click on “SAVE AND CLOSE”!

Maintenance for the same CCTV:

Conduit and Cables

Maintenance • It has been a month since the installation and acceptance of the new CCTV equipment.

•It now should be checked if it works properly through the preventive maintenance checklists.

Maintenance• The trainer is getting ready for the preventive maintenance checks for the CCTV equipment.

• With his laptop or tablet PC, and/or printed documents, he is ready to for the site maintenance checks.

User Manual (How to Open RITSIMS?)

• Find the RITSIMS.exe on your desktop and just click on the application.

User Manual (How to Open RITSIMS?)

• As an alternative, locate the RITSIMS software folder.

• Find the MTSOFT.exe and just click on the application.

User Manual (User Name and Password)

Select user1 as Username

Write 1234 for Password

User Manual (Starting the Applications)

Select “Start Inspection or Maintenance Applications”

User Manual (Equipment Selection)

Select “Closed Circuit

Television Systems”

User Manual (Option Selection)

Select “Maintenanc

e”Option

User Manual (Previous History Check)

Observe the previous

inspection performed.

Click on “NEXT”

User Manual (Options/Components)

Select “Preventive/Routine”Maintenance

Option.Select “CCTV Conduit and

Cables”Click on “START APPLICATION”

User Manual (Questions)

Answer the eight

questions as instructed in

your handout

User Manual (Questions)

Then, click on “Exit” to See the

Final Report

User Manual (Maintenance Report)

See the maintenance

report and write

comments if needed!

User Manual (Maintenance Report)

Change the “Not

Completed” Answers to

“Completed”! When finished, click on “END”.

User Manual (Maintenance Report)

Click on “SAVE AND CLOSE”!

Database Synchronization – Updating Master

Database

User Manual (User Name and Password)

Select user1 as Username

Write 1234 for Password

User Manual (Database Synchronization)

Select “Update Master Database”

User Manual (Database Synchronization)

Select “Inspection

Master Database”

User Manual (Database Synchronization)

Locate the Master Database Fileand Click on it

User Manual (Database Synchronization)

Select “Maintenanc

e Master Database”

User Manual (Database Synchronization)

Locate the Master Database Fileand Click on it

User Manual (Database Synchronization)

Select “Copy to Master Database”

User Manual (Database Synchronization)

Observe the transferred records. Click on “Close”.

History Checks/Queries

User Manual (User Name and Password)

Select user1 as Username

Write 1234 for Password

User Manual (History Option)

Select “History”

option

User Manual (History Option)

Select “Inspection

History”, and Click on “LOAD”

User Manual (History Option)

Select the Inspection

Details, and Click on “GET INSPECTION

REPORT”

User Manual (History Option)

You can make changes for the questions any

time if necessary