Post on 31-Mar-2021
Rothe Erde® Turntablesfor vehicle trailers.Brochure LK 254/13.
A ThyssenKruppTechnologies
companyRothe Erde
TK
2 Rothe Erde.Technology Made-to-measure.
Our product range comprisesball and roller bearings, turn-tables and seamless rolled ringsmade from steel and non-fer-rous metals.
We at Rothe Erde put qualityfirst. All of our service and pro-duction areas from applicationsconsulting to design and manu-facturing, including compre-hensive customer service, arebased on the international DINEN ISO 9001 quality standard.
Rothe Erde Turntables –Products of proven quality
Rothe Erde turntables havebeen developed exclusively forinstallation in vehicle trailers.Their purpose is to transmitboth the axial load, thrust andtraction forces. None of theirparts is susceptible to wear.
The standard series turntablesshown in this brochure are theresult of many years’ designand manufacturing experiencein the field of bogie steeringsystems.
Rothe Erde turntables are builtto the highest manufacturingstandards and are designed tomeet extremely high perform-ance requirements.
Each turntable consists of twosteel rings designed for flangemounting. The raceways aremachined so as to ensure thatthe load transmission is favour-ably directed between the antifriction bearing steel ballsthat are fitted. An initial filling ofgrease protects the racewaysystem.
3
4Bearing Configurations and Bearing Tables.Types 16 L · 16 · 80
Type 16 Lcapable for farmtrucks and carts
of up to 25 km/h
Type 16 capable for light
goods vehicletrailers and farm
trucks of over25 km/h
Type 80capable
for two- andthree-axle trailersof over 25 km/h
4 grease nipplesH1/S-8x1≈ equispaced
H
10
9
ø La
ø B
ø Da
ø U
ø Da1
ø Bø Li
ø Di
ø Da
ø La
ø Di
ø Li
ø U
ø O
4 grease nipplesH1a≈ equispaced
H
8
8
4 grease nipplesH1a≈ equispaced
H
8
8
ø Di
ø Li
ø O
ø Da
ø La
ø U
Drawing Number · Type
310.16.0300.000 · Type 16 L/400
310.16.0400.000 · Type 16 L/500
310.16.0500.000 · Type 16 L/650
310.16.0600.000 · Type 16 L/750
310.16.0700.000 · Type 16 L/850
310.16.0800.000 · Type 16 L/950
310.16.0900.000 · Type 16 L/1050
320.16.0400.000 · Type 16/500
320.16.0500.000 · Type 16/650
320.16.0600.000 · Type 16/750
320.16.0700.000 · Type 16/850
320.16.0800.000 · Type 16/950
320.16.0900.000 · Type 16/1050
330.16.0500.000 · Type 80/685
330.16.0700.010 · Type 80/880
330.16.0900.000 · Type 80/1000
330.16.1000.010 · Type 80/1090
5
236
336
486
586
686
786
886
42
42
42
42
42
42
42
375
475
625
725
825
925
1025
260
360
510
610
710
810
910
–
–
–
–
–
–
–
4
4
4
4
4
4
4
–
–
–
–
–
–
–
346
446
596
696
796
896
996
294
394
544
644
744
844
944
16
16
16
16
16
16
16
7.5
9.0
15.0
18.0
25.0
30.0
35.0
–
–
–
–
–
–
–
1.1
1.1
1.1
1.1
1.1
1.1
1.1
0.7
0.7
0.7
0.7
0.7
0.7
0.7
315
465
565
665
765
865
48
48
48
48
48
48
475
625
725
825
925
1025
340
490
590
690
790
890
–
–
–
–
–
–
4
4
4
4
4
4
–
–
–
–
–
–
434
584
684
784
884
984
381
531
631
731
831
931
16
16
16
16
16
16
18.0
25.0
30.0
35.0
40.0
45.0
–
–
–
–
–
–
1.0
1.0
1.0
1.0
1.0
1.0
0.7
0.7
0.7
0.7
0.7
0.7
567
762
882
972
80
80
80
80
671
866
984
1074
657
852
970
1060
–
16
–
18
4
4
4
4
696
891
1011
1101
–
–
–
–
583
778
898
988
16
16
16
16
35.0
55.0
65.0
70.0
30.0
50.0
60.0
65.0
1.0
1.0
1.0
1.0
0.7
0.7
0.7
0.7
* For different axle combinations, please contact us.
Di[mm]
H[mm]
Li[mm]
La[mm]
B[mm]
Da1[mm]
O[mm]
U[mm]
d[mm]
axial[mm]
radial[mm]
2 axles[kN]
Permissible axial load*
more than2 axles
[kN]n1
320
420
570
670
770
870
970
11
15
20
23
27
30
34
404
504
654
754
854
954
1054
17
23
26
30
34
39
500
650
750
850
950
1050
38
48
58
63
721
916
1036
1126
408
558
658
758
858
958
599
794
914
1004
DL[mm] [kg]
Da[mm]
Rac
e tr
ack
diam
eter
Wei
ght
(app
rox.
)
Out
er d
iam
eter
Inne
r di
amet
er
Ove
rall
heig
ht
Out
er h
ole
circ
ledi
amet
er
Inne
r ho
le c
ircle
diam
eter
Bor
e di
amet
er
Num
ber
of g
reas
eni
pple
s
Dia
met
er
Dia
met
er
Dia
met
er
Bal
l dia
met
er
Bea
ring
clea
ranc
es u
p to
6 Bearing Configurations and Bearing Tables.Types 90 · 90 WA · 90 S
90
ø Daø La
ø Di
ø Da1
ø Li
ø U
ø B
ø B
1010
6 grease nipplesH 1/S 8x1≈ equispaced
90
ø Daø La
ø Di
ø Da1
ø Li
ø U
ø B
ø B
1010
6 grease nipplesAM 8x1, DIN 71412≈ equispaced
Type 90capable for two-
and three-axletrailers of over
25 km/h
Type 90 WAcapable for two-
and three-axletrailers of over
25 km/h
Type 90 WA –low-maintenance turntables
� Raceway systems protectedby seals at upper and lowerbearing gaps.
� Maintenance-free for aminimum of 3 years or amileage of 300,000 kms
360.18.0800.000 · Type 90/1000.18
360.20.0800.000 · Type 90/1000.20
360.22.0800.000 · Type 90/1000.22
360.24.0800.000 · Type 90/1000.24
360.18.0900.010 · Type 90/1100.18
360.20.0900.010 · Type 90/1100.20
360.22.0900.010 · Type 90/1100.22
360.24.0900.010 · Type 90/1100.24
360.22.1000.010 · Type 90/1200.22
360.24.1000.010 · Type 90/1200.24
360.22.1100.010 · Type 90/1300.22
360.22.0955.010 · Type 90/1100.22 WA
360.24.0955.010 · Type 90/1100.24 WA
360.22.1055.010 · Type 90/1200.22 WA
360.24.1055.010 · Type 90/1200.24 WA
360.22.1155.010 · Type 90/1300.22 WA
Drawing Number · Type
370.20.0803.010 · Type 90 S/1000
370.20.0903.010 · Type 90 S/1100
370.20.1003.010 · Type 90 S/1200
370.20.1003.030 · Type 90 S/1200.12
370.24.1003.010 · Type 90 S/1200 SP
90
ø Da
ø La
ø Di
ø Da1
ø Li
ø Uø B
ø B
1010
6 grease nipplesH1/S-8x1≈ equispaced
Type 90 Scapable for two-
and three-axletrailers of over
25 km/h
7
under normal operatingconditions.Should exceptional environ-mental conditions prevailresp. should the turntablebe directly cleaned with a high-pressure equipmentit is necessary to regreasethe turntable untimely.
� Regreasing is necessaryafter the maintenance-freeoperating period has elap-sed.
� Torque:Due to the double seal atthe bearing gaps, a some-what increased torque may
894
894
894
894
994
994
994
994
1094
1094
1194
64
64
64
64
71
71
71
71
79
79
87
1008
1008
1008
1008
1108
1108
1108
1108
1208
1208
1308
854
854
854
854
954
954
954
954
1054
1054
1154
90
90
90
90
90
90
90
90
90
90
90
974
974
974
974
1074
1074
1074
1074
1174
1174
1274
960
960
960
960
1060
1060
1060
1060
1160
1160
1260
–
–
–
–
18
18
18
18
18
18
18
6
6
6
6
6
6
6
6
6
6
6
1000
1000
1000
1000
1100
1100
1100
1100
1200
1200
1300
–
–
–
–
–
–
–
–
–
–
–
885
885
885
885
985
985
985
985
1085
1085
1185
18
20
22
24
18
20
22
24
22
24
22
75.0
90.0
110.0
160.0
90.0
110.0
130.0
180.0
160.0
200.0
180.0
70.0
80.0
100.0
140.0
80.0
100.0
120.0
160.0
140.0
180.0
160.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
71
71
79
79
87
1108
1108
1208
1208
1308
954
954
1054
1054
1154
90
90
90
90
90
1074
1074
1174
1174
1274
1060
1060
1160
1160
1260
18
18
18
18
18
6
6
6
6
6
1100
1100
1200
1200
1300
–
–
–
–
–
985
985
1085
1085
1185
22
24
22
24
22
130.0
180.0
160.0
200.0
180.0
120.0
160.0
140.0
180.0
160.0
0.8
0.8
0.8
0.8
0.8
0.6
0.6
0.6
0.6
0.6
994
994
1094
1094
1194
DL[mm] [kg]
Da[mm]
Di[mm]
H[mm]
Li[mm]
La[mm]
B[mm]
Da1[mm]
O[mm]
U[mm]
d[mm]
axial[mm]
radial[mm]
n1
82
92
101
101
101
1000
1108
1208
1208
1208
834
942
1042
1042
1042
90
90
90
90
90
966
1074
1174
1174
1174
952
1060
1160
1160
1160
18
18
18
18
18
6
6
6
6
6
987
1095
1195
1195
1195
–
–
–
–
–
871
979
1079
1079
1079
20/16
20/16
20/16
20/16
24/16
160.0
200.0
200.0
200.0
300.0
160.0
200.0
200.0
200.0
300.0
1.0
1.0
1.0
1.0
1.0
0.7
0.7
0.7
0.7
0.7
880/ 870
988/ 978
1088/1078
1088/1078
1087/1078
* For different axle combinations, please contact us.
2 axles[kN]
Permissible axial load*
more than2 axles
[kN]
Rac
e tr
ack
diam
eter
Wei
ght
(app
rox.
)
Out
er d
iam
eter
Inne
r di
amet
er
Ove
rall
heig
ht
Out
er h
ole
circ
ledi
amet
er
Inne
r ho
le c
ircle
diam
eter
Bor
e di
amet
er
Num
ber
of g
reas
eni
pple
s
Dia
met
er
Dia
met
er
Dia
met
er
Bal
l dia
met
er
Bea
ring
clea
ranc
es u
p to
develop in comparison withthe normal version. Opera-tion is not impaired by this.
� Mounting dimensions, permissible loads, weightsand drilling patterns are asfor the standard designtype 90.
8
Delivery
The turntables are supplied as either undrilled or drilled bea-rings with the standard typebeing filled with lithium-saponi-fied grease of penetration grade2 and the low-maintenance typewith MOLYKOTE Longterm 2plus.
Type: 80/880
Hole diameter 16 mm.
Special drill holes upon request.
Types: 80/1090,
90/1100.18 to
90/1300.22,
Hole diameter 18 mm.
Special drill holes upon request.
20°
20°
20° 20°
20 °
20°20°
upper ring
20°
10°
17°17°
10°10°
10°
10°
10°
lower ring
type plate (filler plug)type plate (filler plug)
45° 45°
45° 45°
upper ring10
°10
°
16°
16° 16°
lower ring
16°
16°16°
lower ring
direction of travel
welded plate(upper and lower)
upper ring
Delivery.
Every turntable is coated with a primer and can therefore bepainted at the same time as thetrailer. The primer is based on asynthetic resin compound.Attention: if coloured, checkcompatibility with the coatingvarnish!
9
Mounting Holes
If the customer drills the moun-ting holes himself, the typeplate (filler plug) must be offsetto the direction of travel byapprox. 45° (for types 90 S and90 WA inside at the upper ring).Mounting holes are not allowedin the area around the typeplate.
Types: 90 S/1000
90 S/1100
90 S/1200
Hole diameter 18 mm.
Special drill holes upon request.
Types: 90 S/1200.12
90 S/1200 SP
Hole diameter 18 mm.
Special drill holes upon request.
45° 45°
45° 45°
upper ring
10°10°
16°
16°
16°
16°
16°16°
lower ring
type plate (filler plug)
type plate
20°
20°
20° 20°
20 °
20°20°
upper ring
20°
20°
34°
31,5
°
31,5°
lower ring
type plate (filler plug)
type plate
Types: 90/1100.22 WA to
90/1300.22 WA
Hole diameter 18 mm.
Special drill holes upon request.
10°
10°
16°
16° 16°
lower ring
45° 45°
45° 45°
upper ring
16°
16°16°
filler plug
type plate
Mounting Holes.
10 Installation.
Installation
Turntables must be mounted onthe flattest and most distortionproof structure possible. It isessential that at least 50% ofthe peripheral surfaces of theflanges are supported load bea-ring zones and that these latterare roughly equispaced in thedirection of travel and at rightangles to this.
The essential factor here is tosupport the profiled webs of theturntable, thus assuring directforce transmission into the ballraceways. Total out-of-flatness1.3 mm, permissible are forexample 0.8 mm up and 0.5mm down. Larger out-of-flat-nesses have to be compensa-ted by suitable measures(machining of the contact surfa-ces or captive shims in therespective contact area).
The turntable must be fastenedusing at least 8 Grade 8.8 boltsper ring. The bolt lockingsystem must comply with theTÜV’s (German Technical Con-trol Board’s) requirements orwith the prevailing approvalregulations.
The horizontal forces resultingfrom acceleration or decelera-tion must be transmitted by pla-tes welded to the mating struc-tures so as to relieve the load onthe bolts in the radial direction.
To prevent distortion fromoccurring, turntables mustnever be welded on to theirmating structures.
The load details and the boltconnection are only valid foroperation on roads and undertransport conditions as usual inWest Europe.
Table of Tolerances
Type H Flange Da Da1 Di O Uthick-ness
16 L/400and ± 2.0 +8 – +4
16 L/500 -5 -10
16 L/650± 3 ± 3 ± 3
to ± 1.5 +8 – +4
16 L/1050 -4 -10
16/500 ± 2.0 +8 – +4-5 -10
16/650± 3 ± 3 ± 3
to ± 1.5 +8 – +416/1050 -4 -10
80/685to ± 3 ± 1.5 +8 +8 ± 3 – ± 380/1090 -4 -4
90/1000.18to ± 3 ± 1.5 +8 +8 ± 3 – ± 390/1300.22 -4 -4
90/1100.22 WAto ± 3 ± 1.5 +8 +8 ± 3 – ± 390/1300.22 WA -4 -4
90 S/1000to ± 3 ± 1.5 -1.6 -1.6 ± 3 – ± 390 S/1200 SP
11Lubrication and Maintenance.Special Applications.
Lubrication and MaintenanceType 90 Turntables
Prior to installation, the turnta-ble must be regreased whilstturning the upper ring until agrease collar appears at all bea-ring gaps around the entirecircumference. A penetrationgrade 2 lithium-saponified gre-ase should be used for regrea-sing. Regreasing should also becarried out after installation,rotating the turntable to achieveuniform grease distribution. Theintervals for relubrication andexamination of the preload ofthe bolt connections are deter-mined by the installation requi-rements and operating condi-tions. However, the turntablemust be lubricated at least oncea month (please observe trafficauthority requirements, TÜV,etc.).
The “as-supplied“ bearing clea-rances shown in the bearingtables may be allowed to in-crease through wear by a maxi-mum of 3 mm axially andradially. Thereafter, the turnta-ble must be replaced.
MaintenanceType 90 WA Turntables
Our 90 WA turntables are provi-ded with long-term lubricationfor a maintenance-free periodof 3 years minimum or a mile-age of 300,000 kms.
This service period can beextended by relubrication withMolykote Longterm 2 plus (DowCorning, Wiesbaden).
In case of applications withextreme environmental condi-tions specific maintenanceinstructions have to be estab-lished.
The turntables are equippedwith grease fittings. Regreasingor a connection to the vehiclelubrication system is possible.
The preload check of the boltconnections is to be specifiedaccording to the prevailinginstallation requirements andoperating conditions (pleaseobserve traffic authority require-ments, TÜV, etc.).
We recommend to perform a clearance check in conjunctionwith acceptance procedures byTÜV or other accredited testingagencies. If the measurementshows an axial or radial clearan-ce in excess of 3 mm, the turn-table will have to be replaced.
Special Applications
If Types 16, 80 or 90 turntablesare installed in vehicles capableof reaching a speed of up to 25km/h, the permissible axialload may be increased byapprox. 40%, depending on thediameter of the turntable.Please contact us for moredetails.
Details of turntables for non-standard applications and loadcases are available upon speci-al request. Please also refer toour catalogue, “Rothe ErdeLarge Diameter Antifriction Bearings“, KD 210 series.
The contents of this brochureand all the data given hereinhave been meticulously compi-led and proof read.
However, we accept no respon-sibility for any errors or omis-sions.
We reserve the right to introdu-ce design changes or additionsresulting from any improve-ments which may be made.
Rothe Erde
Rothe Erde GmbHTremoniastrasse 5-11D-44137 DortmundPhone: +49 (2 31) 186 -0Fax: +49 (2 31) 186 -25 00E-mail: rotheerde@tkt-re.thyssenkrupp.comInternet: www.rotheerde.com
BerlinRothe Erde GmbHGeschäftsstelle BerlinWittestrasse 30 JD-13509 BerlinPhone: +49 (30) 89 79 14-18Fax: +49 (30) 89 79 14-33E-mail: rotheerde.gsberlin@
tkt-re.thyssenkrupp.com
BrazilRobrasa Rolamentos EspeciaisRothe Erde Ltda.Rua Lidia Blank, No. 48BRA-CEP 09913-010, Diadema, São PauloPhone: +55 (11) 40 57 48 77Fax: +55 (11) 40 55 38 92E-mail: robrasa@ibm.netInternet: www.robrasa.ind.br
ChinaXuzhou Rothe Erde Slewing Bearing Co., Ltd.Wanzhai, Northern Suburb,VRC-Xuzhou 221007, JiangsuPhone: +86 (5 16) 7 76 71 70Fax: +86 (5 16) 7 76 90 00E-mail: xuzhou_rothe_erde@
xreb.comInternet: www.xreb.com
FranceRoballo France S.à r. l.30, Boulevard BelleriveF-92566 Rueil Malmaison CEDEXPhone: +33 (1) 41 39 00 90Fax: +33 (1) 41 39 00 99E-mail: roballofra@wanadoo.fr
NorthRothe Erde GmbHGeschäftsstelle NordAm Pferdemarkt 31D-30853 LangenhagenPhone: +49 (5 11) 7 25 35 69-0Fax: +49 (5 11) 7 25 35 69-9E-mail: rotheerde.gsnord@
tkt-re.thyssenkrupp.com
SouthRothe Erde GmbHGeschäftsstelle SüdAm Ostkai 15D-70327 StuttgartPhone: +49 (7 11) 3 27 79 19-0Fax: +49 (7 11) 3 27 79 19-9E-mail: rotheerde.gssued@
tkt-re.thyssenkrupp.com
Great BritainRoballo Engineering Co. Ltd.Mill HillNorth West Industrial EstateGB-Peterlee, Co. Durham SR8 2HRPhone: +44 (1 91) 5 18 56 00Fax: +44 (1 91) 5 86 90 96E-mail: info@roballo.co.ukInternet: www.roballo.co.uk
IndiaRothe Erde GmbHLiaison Office IndiaC-16, Bhagat Singh MargOff Prabhu Marg Tilak NagarIND-Jaipur 302 004Phone: +91 (1 41) 2 62 42 47Fax: +91 (1 41) 2 62 42 30 E-mail: re_india@vsnl.netInternet: www.rotheerdeindia.com
ItalyRothe Erde-Metallurgica RossiS.p.A.Viale Kennedy, 56I-25010 Visano (Brescia)Phone: +39 (0 30) 95 20-1Fax: +39 (0 30) 95 20- 3 00E-mail: mri@rotheerde.itInternet: www.rotheerde.it
JapanNippon Roballo Co., Ltd.Fukide Bldg., 7th FloorToranomon 4-1-13J-Minato-Ku/TokyoZip: 1 05-00 01Phone: +81 (3) 34 34 43 41Fax: +81 (3) 34 34 43 40E-mail: info@roballo.co.jpInternet: www.roballo.co.jp
SpainRoteisaRothe Erde Ibérica S.A.Carretera Castellón, km. 7Polígono Industrial „La Cartuja“E-50720 La Cartuja Baja (Zaragoza)Phone: +34 (9 76) 50 04 80Fax: +34 (9 76) 50 01 54E-mail: roteisa@roteisa.esInternet: www.roteisa.es
USARotek Incorporated1400 South Chillicothe Rd.P.O. Box 312USA-Aurora, Ohio 44202Phone: +1 (3 30) 5 62 40 00Fax: +1 (3 30) 5 62 46 20E-mail: sales@rotek-inc.comInternet: www.rotek-inc.com
11.0
3/1.
0 Th
is p
ublic
atio
n m
ay n
ot b
e re
prod
uced
in w
hole
or
in p
arts
with
out
perm
issi
on.
All
right
s re
serv
ed.
Prin
ted
in G
erm
any.
Indi
vidu
al d
etai
ls o
f th
is in
form
atio
n sh
all o
nly
then
be
cons
ider
ed a
qua
lity
resp
. du
rabi
lity
guar
ante
e w
hen
each
suc
h ca
se is
exp
ress
ly c
onfir
med
by
us in
writ
ing.
Head Office
Offices in Germany
Subsidiaries
®