Post on 12-Sep-2014
SPATER
DEPARTMENT OF AERONAUTICAL ENGINEERING
AE-1304
PROPULSION-1
SPATER
UNIT-1
FUNDAMENTALS OF GAS TURBINE ENGINES
SPATER
INTRODUCTION
• Comprehend the thermodynamic processes occurring in a gas turbine
• Comprehend the basic components of gas turbine engines and their basic operation
• Comprehend the support systems associated with gas turbine engines
SPATER
ADVANTAGES OF GTE’s
– Weight reduction of 70%– Simplicity– Reduced manning requirements– Quicker response time– Faster Acceleration/deceleration– Modular replacement– Less vibrations– More economical
SPATER
DISADVANTAGES OF GTE’s
• Many parts under high stress
• High pitched noise
• Needs large quantities of air
• Large quantities of hot exhaust (target)
• Cannot be repaired in place
SPATER
SPATER
SPATER
SPATER
SPATER
SPATER
SPATER
SPATER
SPATER
BRAYTON CYCLE
Unlike diesels, operate on STEADY-FLOW cycleOpen cycle, unheated engine1-2: Compression
2-3: Combustion
3-4: Expansion through Turbine and Exhaust Nozzle
(4-1: Atmospheric Pressure)
SPATER
BASIC COMPONENTS
SPATER
NUMBERING OF TURBINE ENGINES
intake compressor burner turbine afterburner (AB) nozzle (n)
(diffuser)
(e.g., turbofan)
SPATER
COMPRESSOR
• Supplies high pressure air for combustion process
• Compressor types– Radial/centrifugal flow compressor– Axial flow compressor
SPATER
SPATER
COMPRESSOR
• Radial/centrifugal flow– Adv: simple design, good
for low compression ratios (5:1)
– Disadv: Difficult to stage, less efficient
• Axial flow – Good for high
compression ratios (20:1)– Most commonly used
SPATER
THE THRUST EQUATION
SPATER
SPATER
SPATER
FACTORS AFFECTING THRUST
• PRESSURE• TEMPERATURE• DENSITY• HUMIDITY• ALTITUDE• FORWARD VELOCITY
SPATER
METHODS OF THRUST AUGMENTATION
• AFTER BURNING• INJECTION OF WATER & ALCOHOL MIXTURE• BLEED BURN CYCLE
SPATER
SPATER
UNIT-II
SUBSONIC & SUPERSONIC INLETS FOR JET ENGINES
SPATER
INTRODUCTION
Inlets are very important to the overall jet engine performance & will greatly influence jet engine thrust output.
The faster the airplane goes the more critical the inlet duct design becomes.
Engine thrust will be high only if the inlet duct supplies the engine with the required airflow at the highest possible pressure.
SPATER
The nacelle/duct must allow the engine to operate with minimum stall/surge tendencies & permit wide variation in angle of attack & yaw of the aircraft.
For subsonic aircraft, the nacelle shouldn’t produce strong shock waves or flow separations & should be of minimum weight for both subsonic & supersonic designs.
For certain military applications, the radar cross sectional control or radar reflectance is a crucial design requirements.
SPATER
Inlet ducts add to parasite drag skin friction+ viscous drag) & interference drag.
It must operate from static ground run up to high aircraft Mach number with high duct efficiency at all altitude, attitudes & flight speeds.
It should be as straight & smooth as possible & designed such a way that Boundary layer to be minimum.
It should deliver pressure distribution evenly to the compressor.
SPATER
Spring loaded , blow-in or such-in-doors are sometimes placed around the side of the inlet to provide enough air to the engine at high engine rpm & low aircraft speed.
It must be shaped such a way that ram velocity is slowly & smoothly decreases while the ram pressure is slowly & smoothly increases.
SPATER
DUCT EFFICIENCY
The duct pressure efficiency ratio is defined as the ability of the duct to convert the kinetic or dynamic pressure energy at the inlet of the duct to the static pressure energy at the inlet of the compressor without a loss in total pressure . It is in order of 98% if there is less friction loss.
SPATER
RAM RECOVERY POINT
The ram recovery point is that aircraft speed at which the ram pressure rise is equal to the friction pressure losses or that aircraft speed at which the compressor inlet total pressure is equal to the outside ambient air pressure.
A good subsonic duct has 257.4 km/h.
SPATER
SINGLE ENTRANCE DUCT
SPATER
SUBSONIC DUCTS
SPATER
VARIABLE GEOMETRY DUCT FOR SUPERSONIC A/C
SPATER
NORMAL SHOCK RELATION
SPATER
OBLIQUE SHOCK RELATIONS
SPATER
BOUNDARY LAYER
SPATER
UNIT-III
COMBUSTION CHAMBERS
SPATER
COMBUSTION CHAMBER
• Where air & fuel are mixed, ignited, and burned
• Spark plugs used to ignite fuel
• Types– Can: for small, centrifugal compressors– Annular: for larger, axial compressors (LM
2500)– Can-annular: for really large turbines
SPATER
SPATER
SPATER
SPATER
SPATER
UNIT-IV
NOZZLES
SPATER
INTRODUCTION
• The primary objective of a nozzle is to expand the exhaust stream to atmospheric pressure, and form it into a high speed jet to propel the vehicle. For air breathing engines, if the fully expanded jet has a higher speed than the aircraft's airspeed, then there is a net rearward momentum gain to the air and there will be a forward thrust on the airframe.
SPATER
• Many military combat engines incorporate an afterburner (or reheat) in the engine exhaust system. When the system is lit, the nozzle throat area must be increased, to accommodate the extra exhaust volume flow, so that the turbo machinery is unaware that the afterburner is lit. A variable throat area is achieved by moving a series of overlapping petals, which approximate the circular nozzle cross-section.
SPATER
• At high nozzle pressure ratios, the exit pressure is often above ambient and much of the expansion will take place downstream of a convergent nozzle, which is inefficient. Consequently, some jet engines (notably rockets) incorporate a convergent-divergent nozzle, to allow most of the expansion to take place against the inside of a nozzle to maximise thrust. However, unlike the fixed con-di nozzle used on a conventional rocket motor, when such a device is used on a turbojet engine it has to be a complex variable geometry device, to cope with the wide variation in nozzle pressure ratio encountered in flight and engine throttling. This further increases the weight and cost of such an installation.
SPATER
• The simpler of the two is the ejector nozzle, which creates an effective nozzle through a secondary airflow and spring-loaded petals. At subsonic speeds, the airflow constricts the exhaust to a convergent shape. As the aircraft speeds up, the two nozzles dilate, which allows the exhaust to form a convergent-divergent shape, speeding the exhaust gasses past Mach 1. More complex engines can actually use a tertiary airflow to reduce exit area at very low speeds. Advantages of the ejector nozzle are relative simplicity and reliability. Disadvantages are average performance (compared to the other nozzle type) and relatively high drag due to the secondary airflow. Notable aircraft to have utilized this type of nozzle include the SR-71, Concorde, F-111, and Saab Viggen
SPATER
SPATER
NOZZLE
SPATER
1-D ANALYSIS OF GAS
SPATER
SPATER
MASS FLOW RELATION
SPATER
UNIT-V
COMPRESSORS
SPATER
• Compressor– Draws in air & compresses it
• Combustion Chamber– Fuel pumped in and ignited to burn with
compressed air
• TurbineTurbine– Hot gases converted to work– Can drive compressor & external load
SPATER
COMPRESSOR
• Controlling Load on Compressor– To ensure maximum efficiency and allow for
flexibility, compressor can be split into HP & LP sections
– Vane control: inlet vanes/nozzle angles can be varied to control air flow
• Compressor Stall– Interruption of air flow due to turbulence
SPATER
USE OF COMPRESSED AIR
• Primary Air (30%)– Passes directly to combustor for combustion
process
• Secondary Air (65%)– Passes through holes in perforated inner shell
& mixes with combustion gases
• Film Cooling Air (5%)– Insulates/cools turbine blades
SPATER
SPATER
VELOCITY TRIANGLE
SPATER
THANK U