Post on 02-Jun-2018
8/10/2019 ppt on heat tratment process
1/20
8/10/2019 ppt on heat tratment process
2/20
> What is heat treatment process ?
> What are it effects?
8/10/2019 ppt on heat tratment process
3/20
> Why ? Toughness
Hardness
Ductility
Machineability
Refine Grain Structure
Residual Stresses
Wear Resistance
8/10/2019 ppt on heat tratment process
4/20
Aircraft Industry
Automobile Manufacturing
Defense Sector Forging
Foundry
Heavy MachineryManufacturing
Powder Metal Industries
> Application
8/10/2019 ppt on heat tratment process
5/20
Commonly Heat Treated Metals
> Ferrous Metals Steel Cast Iron Alloys Stainless Steel Tool Steel> Non-ferrous Metals Aluminum Copper
Brass Titanium
8/10/2019 ppt on heat tratment process
6/20
Types of heat treatment processes
Austempering Martempering Ausforming
8/10/2019 ppt on heat tratment process
7/20
Time-Temperature-Transformation(TTT)Curve
TTT diagram is a plot of temperatureversus the logarithmof time for a steel alloy of definite composition.
It is used to determine when transformations begin andend for an isothermal heat treatment of a previouslyaustenitizedalloy
TTT diagram indicates when a specific transformation starts and
ends and it also shows what percentage of transformation of
austeniteat a particular temperature is achieved.
8/10/2019 ppt on heat tratment process
8/20
Time-Temperature-Transformation (TTT)Curve
8/10/2019 ppt on heat tratment process
9/20
Continuous-cooling-tranformation(CCT)Curve
CCT diagram depends on composition of steel, nature ofcooling, austenite grain size, extent of austenitehomogenising, as well as austenitising temperature and time.
continuous cooling occurs through a series of isothermalsteps and the time spent at each of these steps depends onthe rate of cooling. The difference between successiveisothermal steps can be considered to approach zero.
The transformation at a temperature is not independent tocooling above it.
8/10/2019 ppt on heat tratment process
10/20
CCT diagram depends on composition of steel, nature ofcooling, austenite grain size, extent of austenitehomogenising, as well as austenitising temperature andtime.
continuous cooling occurs through a series of isothermalsteps and the time spent at each of these steps depends onthe rate of cooling. The difference between successiveisothermal steps can be considered to approach zero.
The transformation at a temperature is not independent tocooling above it.
8/10/2019 ppt on heat tratment process
11/20
Continuous-Cooling-Transformation(CCT)Curve
8/10/2019 ppt on heat tratment process
12/20
Critical-Cooling-Rate-(CCR)Curve
When cooling curve is tangent to the nose of TTT- curve, it is
called as critical cooling rate. It can be defined as in twoways:1) Slowest cooling rate at which unstable austenite can beconverted into martensite. OR
2) fastest cooling rate at which unstable austenite can beconverted into pearlite. CCR is a dividing line between martensite and pearlite
transformation.
Factors affecting on CCR:1) carbon content2) Austenitic temperature
8/10/2019 ppt on heat tratment process
13/20
Critical-Cooling-Rate-(CCR)Curve
8/10/2019 ppt on heat tratment process
14/20
>Ausforming It is a hardeningprocess that produces very high strength
steel. This process converts metastable austensite to martensite
by quenching, and increase in strength upto 50% without anyloss in ductility. due to this fine structure will also changes.
Strengthening is directly proportional to deformation.1) Process:
Steel is heated to austenitic region.Temperature ismaintained so that uniform structure from surfece tocore.coolingis done between the temperature Ms Andnose.At this temperature- forging/rollingthen cooled at
room teperature.2) Properties:Gives better combination of tensile strength of 3000 N/m^2.
3)Application:Aircraft and automotive craft.
8/10/2019 ppt on heat tratment process
15/20
> Ausforming
8/10/2019 ppt on heat tratment process
16/20
> Austempering
8/10/2019 ppt on heat tratment process
17/20
Austempering is an isothermal heat treatment that, when
applied to ferrous materials, produces a structure that is
stronger and tougher than comparable structures producedwith conventional heat treatments.
Conventional heat treaters heat the parts to "red heat" in acontrolled atmosphere and then quench them in a bath of oil
or water that is near room temperature. (Maybe even as highas a few hundred degrees Fahrenheit).
This produces a crystalline structure known as Martensite, a
hard, brittle phase. The parts are then tempered in anotherfurnace at 350F (177C) to 1100F (593C) to decrease the"brittleness.
During the process of quenching to Martensite, theMartensite reaction begins immediately.
8/10/2019 ppt on heat tratment process
18/20
> Martempering
8/10/2019 ppt on heat tratment process
19/20
Quenching from the austenitizing temperature into a hotfluid medium (hot oil, molten salt, molten metal, or afluidized particle bed) at a temperature usually above themartensite range (Ms point)
Holding in the quenching medium until the temperaturethroughout the steel is substantially uniform
Cooling (usually in air) at a moderate rate to prevent large
differences in temperature between the outside and thecenter of the section
8/10/2019 ppt on heat tratment process
20/20
Thank y ou..