Post on 03-Jul-2018
Physics Course
Questions
Advanced Higher
8097
.
November 2000
HIGHER STILL
Physics Course Questions
Advanced Higher
Support Materials
This publication may be reproduced in whole or in part for educational purposes provided that no profit
is derived from the reproduction and that, if reproduced in part, the source is acknowledged.
First published 2000
Higher Still Development Unit
PO Box 12754
Ladywell House
Ladywell Road
Edinburgh
EH12 7YH
INTRODUCTION
Course assessment will require candidates to respond to questions which integrate the
work studied across the component units as well as to questions which are less
structured and set in less familiar and more complex contexts (Advanced Higher
Physics, National Course Specification page 19, Second edition - December 1999).
A unit assessment in Advanced Higher Physics contains questions designed to assess
achievement of the performance criteria associated with that unit and is not intended
to grade or rank the candidates. The course assessment is designed to grade, hence
certain questions, or parts of questions, are designed to assess the attainment of the
candidate against the Grade descriptions for the award at ‘A’.
Generating evidence for estimates of performance and for appeals
The unit assessments cannot be used on their own to provide an estimate of
performance or as evidence for appeals. Course type questions are required for these
purposes. These questions must emulate the demands of the external course
assessment. This pack provides examples of this type of question. The questions,
provided in the specimen question paper, are further sources.
A prelim paper attempted after the completion of two units can provide useful
evidence for appeals. Such a paper might reflect the format and duration of the final
examination paper and provide useful practice of examination technique. For this
paper to be a suitable basis on which to submit an appeal, it must be able to persuade
the Principal Assessor that it:
has not been seen by the candidate
offers a suitable level of demand
allows for a demonstration of the criteria associated with the Grade
descriptions for the “C” and “A” awards.
The test paper can contain questions which are in the public domain. It is not intended that all staff across Scotland should construct new questions when there are
valid past paper questions available from previous years. However the use of a
complete paper e.g. that of the previous year or so, is unlikely to prove acceptable to
SQA in that there is a high probability that the candidate has seen these questions.
A prelim paper consisting of a variety of questions of suitable demand from a range of
sources should be set. The paper should include questions that require candidates to
integrate across at least two units. Such a prelim would be supplemented by evidence
of attainment in the remaining unit, for example, by a short test of course type
questions on that unit.
Although the prelim is a preferred method in many centres, this is not a requirement
of SQA and a number of appropriate shorter tests of suitable demand makes a possible
alternative.
The questions
Many of the questions in this pack are based on previous CSYS questions. These
have been selected and adapted to reflect the demands of the Advanced Higher
syllabus.
Physics: Course Questions (Advanced Higher) 1
Solutions and marking scheme
Brief solutions to all questions have been provided at the end of this pack. These
solutions are designed to be of assistance to staff in marking student’s scripts.
The general instructions for markers issued by SQA in 1999 should be used as an
additional guide for awarding marks. Comments have been made to assist marking
and highlight specific points.
For questions involving calculations where two marks are allocated, the following
general rule for the award of partial marks should be applied:
{½} for the formula, {½} for substitution,
{1} for final answer. If the unit in final answer is wrong or missing deduct {½}.
This is denoted in the marking scheme as [standard marking].
Where a question involving a calculation has more than two marks allocated,
comment is provided to assist in awarding marks. In some cases alternative methods
of responding to the question have been identified.
For questions calling for a description or an explanation a brief solution has been
provided. Professional judgement should be applied in giving credit for alternative
correct answers.
Credit should be given for correct physics. Wrong physics is always penalised.
It is appropriate to emphasise that in any external examination paper, markers attend a
‘marker’s meeting’ where marking of the individual questions are discussed.
Decisions are then made on any finer points and markers all agree to apply these
decisions in their individual marking in order to ensure uniformity across the scripts.
In addition at the ‘standardisation’ the examining team cross mark a selection of
scripts from each marker to ensure that there is a uniformity of marking. Any
‘excessive strict’ or ‘excessive lenient’ marking is adjusted accordingly.
Physics: Course Questions (Advanced Higher) 2
MECHANICS
1. A child of mass 40 kg swings in a horizontal circle of radius 2.0 m by holding
the end of a rope attached to a vertical post as shown in the figure below.
The child completes one revolution in 4.0 s
(a) Find:
(i) the speed of the child
(ii) the horizontal component of tension in the rope
(iii) the vertical component of tension in the rope
(iv) the angle made by the rope with the pole. 8
(b) The child lets go when his feet are 0.50 m above the ground. Calculate
how far from the post he lands. State any assumption you made. 4
(12)
Physics: Course Questions (Advanced Higher) 3
2. A solid wheel and axle is allowed to roll from rest at AA/ down an inclined
set of rails as shown in Figure 1.
Figure 1
The following information is given:
Mass of wheel and axle assembly = 1.4 kg
Height of AA/
above BB/
= 0.40m
Distance between AA/
and BB/
= 2.0 m Diameter of axle = 1.0 cm
Time to travel from AA/
to BB/
= 30 s
(a) Calculate the speed of the solid wheel when it reaches BB/.
2
(b) Calculate the angular velocity of the solid wheel at BB/.
2
(c) (i) Write down an expression for the total rotational and translational
kinetic energy of the wheel at BB/.
(ii) Find the moment of inertia of the wheel. 3
(d) The experiment is repeated with a spoked wheel as shown in Figure 2.
The spoked wheel is mounted on an identical axle and has the same mass
as the solid wheel. The radius of the spoked wheel is greater than that of
the solid wheel.
Figure 2
(i) State and explain how the moment of inertia of the spoked wheel
compares with the moment of inertia of the solid wheel.
(ii) State and explain how the time taken for the spoked wheel to reach
BB/
compares with the time taken for the solid wheel to reach BB/. 4
(11)
Physics: Course Questions (Advanced Higher) 4
3. (a) State the mathematical expression of the inverse square law of gravitation 1
(b) (i) Show that the speed, v, of a satellite in orbit around the Earth is given by
v GM E
. r
(ii) In the above expression state the meaning of the symbols G, ME
and r. 3
(c) A satellite of mass 120 kg is placed in orbit 600 km above the Earth.
(i) Calculate the kinetic energy of the satellite
(ii) State the expression for the gravitational potential at a distance r
from a mass M.
(iii) Due to the work done by friction the orbit of the satellite decreases to
580 km above the Earth. Calculate the loss of potential energy of the satellite.
(iv) State and explain what happens to the kinetic energy of the satellite
when the orbit decreases. 7
(11)
4. (a) State what is meant by the moment of inertia of a rigid oject about an
axis of rotation.
1
(b)
The rotor of an electricity generator in a power station can be considered
as a uniform cylinder rotating about its axis. The manufacturer quotes the
following data for such a rotor:
Rotor diameter = 3.6 m
Rotor mass = 210 103
kg
Moment of inertia of rotor = 3.4 105
kg m2
“Running Speed” = 600 revolutions per minute Time to reach running speed from rest = 30 s
(i) Calculate the angular acceleration of the rotor as it is brought from
rest to its running speed. You may assume that the acceleration is
uniform.
(ii) Calculate the torque exerted on the rotor.
(iii) What is the kinetic energy of the rotor at its “running speed”?
(iv) Due to the motion of the rotor, a nut on the surface of the rotor
experiences a force. The mass of the nut is 0.80 kg. The rotor is
turning at its designed running speed. Calculate the size of the force
experienced by the nut.
(v) Explain why there is a limit to the safe running speed of the rotor. 9
(10)
Physics: Course Questions (Advanced Higher) 5
1
5. When a car is moving at a steady speed, it may be assumed that each piston in
the engine moves with simple harmonic motion.
(a) A piston has a mass of 0.35 kg and a stroke (twice the amplitude) of
7.6 cm. When the engine is turning at 3000 revolutions per minute, find:
(i) the maximum acceleration of the piston
(ii) the position or positions where the maximum acceleration occurs
(iii) the maximum force exerted on the piston
(iv) the maximum speed of the piston
(v) the maximum kinetic energy of the piston. 9
(b) Explain, in terms of the physical principles involved, the effects of over
revving the engine. 2
(11)
6. (a) In a particle accelerator, protons can be made to travel at speeds
approaching the speed of light. Using the relationship:
m m
0
1
v 2 2
c 2
(i) determine the speed of a proton, when its relativistic mass is double
its rest mass
(ii) calculate the relativistic energy of a proton travelling at this speed. 4
(b) In a hydrogen atom, the angular momentum of the electron is quantised.
(i) Calculate the lowest value for the angular momentum of the
electron.
(ii) When the electron has its lowest angular momentum, the orbital
radius of the electron is 5.3 10-11
m. Calculate the linear momentum of the electron in this case.
(iii) Calculate the de Broglie wavelength of the electron in a hydrogen
atom when it has its lowest angular momentum. 6
(10)
Physics: Course Questions (Advanced Higher) 6
7. The figure below shows a Ferris wheel, at a fun fair, which rotates in a
vertical plane about a horizontal axis.
Data for the Ferris wheel is given below.
Moment of inertia of the wheel empty = 8.8 105
kg m2
Maximum passenger mass per chair = 200 kg
Number of chairs = 16
Radius of the wheel = 10 m
The Ferris wheel is loaded to a maximum. When rotating at its maximum
angular speed, the period of rotation of the wheel is 30 s
(a) Calculate the moment of inertia of the fully loaded Ferris wheel. 2
(b) Calculate the rotational kinetic energy of the loaded wheel at this
maximum angular speed. 2
(c) With the driver motor switched off and no application of the brakes, the
system decelerates uniformly to rest from its maximum speed. The
wheel takes 20 revolutions to come to rest.
(i) Calculate the angular deceleration of the wheel.
(ii) Calculate the frictional torque which causes this deceleration. 4
(d) A passenger will experience a force exerted by the seat. When the seat is
at the highest position, this force is a minimum.
(i) Explain why this is the case.
(ii) Calculate the value of this force experienced by a 50 kg passenger. 4
(12)
Physics: Course Questions (Advanced Higher) 7
8. (a) An ice skater changes her angular velocity in a spin by pulling in her
outstretched arms (Figure 1(a)) until they are close to her body (Figure
1(b)).
Figure 1(a) Figure 1(b)
(i) State what happens to her angular velocity
(ii) Explain the change produced, taking into account that her body mass
does not alter and that no external torque is applied. 3
(b) A turntable is in the form of a disc with a moment of inertia about the
central vertical axis of 0.024 kg m2. The turntable rotates in the
horizontal plane on very low friction bearings about its centre. The
angular velocity of the turntable is 8.0 rad s-1
. A small dart of mass 0.15 kg is now dropped from rest just above the
turntable. The dart sticks into the turntable at a distance of 0.14 m from
its centre as shown in Figure 2.
Figure 2
(i) Calculate the moment of inertia of the dart and turntable together.
(ii) Calculate the new angular velocity of the system.
(iii) Calculate:
(A) the kinetic energy of the turntable before the dart is dropped
(B) the kinetic energy of the turntable and dart after the dart has
been dropped.
(iv) Account for the change in kinetic energy. 8
(11)
Physics: Course Questions (Advanced Higher) 8
Ex
ten
sio
n/m
m
9. In an experiment to measure the gravitational acceleration g, a mass was
suspended from a spiral spring. The resulting extension of the spring was
measured. The mass was then pulled down a little further, released, and
allowed to oscillate. The periodic time of the oscillations was measured.
This was repeated for a number of different masses.
The graph of extension against mass from the readings obtained is shown
below.
160
120
80
40
0
0 0.1 0.2 0.3 0.4 0.5
Mass/kg
Physics: Course Questions (Advanced Higher) 9
(a) From the graph:
(i) obtain a value for the spring extension per unit mass
(ii) find the uncertainty in this value
(iii) what mass would produce an extension of 1 m? 5
(b) When the mass is displaced from its equilibrium position, the restoring
force is given by:
F ky
where k is the force per unit extension or spring constant measured in
N m-1.
(i) Show that the periodic time T of the oscillation is given by:
M T 2
k
where M is the mass suspended from the spring.
(ii) The values obtained for the periodic time of the oscillations for
different masses are shown below.
Mass M / kg
0.10
Periodic time T / s
0.38
0.20 0.53
0.30 0.63
0.40 0.74
0.50 0.82
(A) Plot a straight line graph to verify the relationship between T
and M.
(B) Use the gradient of your graph to find a value for k.
(C) From your value for k and your answer to (a) (iii), obtain a
value for g, the gravitational acceleration. 8
(12)
Physics: Course Questions (Advanced Higher) 10
10. (a) (i) State what is meant by ‘escape velocity’.
(ii) Show that the expression for the escape velocity from a planet of
mass M is given by:
2GM v
r
where the symbols have their usual meaning.
(iii) Calculate the escape velocity from the Moon. The radius of the
Moon is 2.6 106 m. 5
(b) It is believed that stars which are sufficiently massive may collapse to
form a black hole when their nuclear fuel is exhausted at the end of their
life. A star with a mass three times the mass of the Sun could collapse to
form a black hole of radius less than 10 km.
What is meant by a ‘black hole’? 1
(6)
Physics: Course Questions (Advanced Higher) 11
2
11. A disc is mounted on a bearing as shown in the figure below.
Hanging weight
The hanging weight produces a constant torque on the disc. The disc rotates
with a uniform angular acceleration, .
The disc is released from rest and the time taken for five complete rotations
while accelerating is measured with a stopclock. The experiment is repeated
seven times and the readings are shown below.
Experiment
1
Time t for five rotations / s
9.80
2 9.42
3 9.66
4 9.93
5 9.92
6 9.35
7 9.63
(a) Find the mean time t and the approximate random uncertainty in the
mean. 3
(b) The equation for the angular displacement of an object accelerating
uniformly from rest is given by
1 t 2 .
(i) Use the mean time t to calculate the angular acceleration .
(ii) Calculate the uncertainty in from the uncertainty in t. 4
(c) The moment of inertia I of the disc is given by
mgr I .
d
where m is the mass of the hanging weight, g is the acceleration due to
gravity, r is the radial arm of the accelerating torque, and d is the
angular deceleration of the moving disc due to the frictional torque after
the hanging mass is removed.
Calculate the value of I and the uncertainty in I given that:
m = 0.011 0.001 kg
r
d
g
= 0.012 0.002 m
= 0.050 0.003 rad s-2
= 9.81 0.01 m s-2.
4
(11)
Physics: Course Questions (Advanced Higher) 12
ELECTRICAL PHENOMENA
12. (a) Air ceases to be an effective insulator at an electric field strength of
3.0 106
V m-
1.
(i) Write down an expression for the electric field strength E between
parallel plates separated by a distance d when the potential
difference between the plates is V.
(ii) Two parallel plates are separated by a distance of 1.5 mm. Calculate the
p.d. between the plates when insulation of the air between plates breaks
down. 2
(b) An uncharged spherical conducting sphere is placed in the region
between two charged plates as shown in the figure below.
_ +
(i) State the nature of the electric field inside the sphere.
(ii) Copy the diagram.
(A) Show the distribution of charge on the sphere.
(B) Sketch the electric field in the region between the plates. 4
(c) (i) The electrostatic potential V at a distance r from a point charge Q is
Q V .
4o r
Write down an expression for the potential at the surface of a
conducting sphere of radius R and charge Q.
(ii) Calculate the charge on a conducting sphere of diameter 100 mm
when the potential of the sphere is 1.8 kV. 3
(9)
Physics: Course Questions (Advanced Higher) 13
13. (a) (i) Draw an arrangement of point charges which gives a point in space
where the electrostatic potential is zero and the electric field strength
is non zero. Indicate the point concerned.
(ii) Draw an arrangement of point charges which gives a point in space
where the electrostatic potential is non zero and the electric field intensity is zero. Indicate the point concerned. 4
(b) Two protons are separated by a very large distance. They are projected
towards each other along the same straight line with equal speeds.
(i) The protons are momentarily at rest at a minimum separation rmin .
Write down an expression for the electrostatic potential at one
proton due to the field of the other.
(ii) Hence write down an expression for the electrostatic potential
energy when the separation is rmin
(iii) Given that rmin is 5.0 10-15
m find the initial speed of the
protons, stating any principle that you use in your calculation.
(iv) Calculate the potential difference required to accelerate protons in a
linear electrostatic accelerator in order to achieve the speed determined in (b) (iii). 7
(11)
14. (a) An electron moving with a constant speed of 2.0 106
m s-1
enters a
region of space where there is a uniform magnetic field. The magnetic
induction of the magnetic field is 0.50 mT. The path of the electron
makes an angle of 30 with the direction of the magnetic field as shown
in the figure below.
(i) Explain why the resultant movement of the electron must be helical.
(ii) Calculate the component of the electron’s velocity perpendicular to
the field.
(iii) Write down an expression equating the force on the electron with the
central force required for circular motion.
(iv) Find the time for the electron to complete one turn of the helical
path. 7
(b) The speed of the electron is doubled. Explain the effect on the time
calculated in (a) (iv)? 2
(9)
Physics: Course Questions (Advanced Higher) 14
15. (a) The force F on a current carrying conductor in a magnetic field is given
by:
F I l B sin .
Derive the relationship for the magnitude of the force acting on a charge
q moving with speed v perpendicular to a magnetic field B. 2
(b) A beam of positively charged particles enters through slit X into a region
where there is a uniform magnetic induction B and uniform electric field
strength E.
Z
X Y
Each particle has a mass m, charge q and speed v.
Plate Z is made positive with respect to the earthed plate.
(i) State the directions of the electric and magnetic fields when the
particles pass through the region undeflected to leave by slit Y.
(ii) Write down an expression equating the forces due to the electric and
magnetic fields.
(iii) Derive an expression which shows the relationship between v, E,
and B.
(iv) The potential difference between the plates is 550 V. The plate
separation is 0.12 m.
(A) Calculate the electric field strength between the plates.
(B) The charged particles travelling undeflected between X and Y
have a speed of 1.2 103
m s-1
.
Calculate the magnetic induction of the magnetic field. 7
(9)
Physics: Course Questions (Advanced Higher) 15
16. (a) (i) State what is meant by electric field strength E at a point.
(ii) Write down an expression for the force F which acts on a charge q in
an electric field of strength E. 2
(b) In an oscilloscope, electrons travelling at a speed of 1.5 107
m s-1
enter midway between the y-plates as shown in the figure below. The
length and separation of the plates are shown. The potential difference
between the plates is 40 V.
0.050 m
0.020 m
(i) Describe the motion of the electrons as they pass between the plates.
(ii) Calculate the vertical displacement y of the electrons as they leave
the region between the plates.
(iii) By considering horizontal and vertical components of velocity, or
otherwise, calculate the angle between the horizontal and the path
of the electrons as they emerge from the field between the plates. 7
(9)
17. (a) A solenoid is connected to a d.c. supply as shown in the diagram below.
S
The switch S is closed.
(i) Draw a graph to show how the current varies with time.
(ii) Explain the shape of the graph. 3
(b) A coil of inductance 6.0 H and resistance 4.0 is connected to a 24 V
d.c. supply of negligible internal resistance.
Calculate:
(i) the maximum current in the circuit
(ii) the maximum potential difference across the coil
(iii) the maximum rate of change of current in the coil. 5
(8)
Physics: Course Questions (Advanced Higher) 16
18. In the apparatus shown in the figure below, a beam of singly charged positive ions enters an evacuated chamber at A. The ions travel between plates P1 and
P2 before passing through slit S, normal to XY.
The whole apparatus is in a uniform magnetic field of magnetic induction 0.60 T. The potential difference between plates P1 and P2 is 3000 V. The
distance between P1 and P2 is 20 mm. The deflected ions form lines on a
photographic plate W.
(a) Show in a sketch, the polarity of plates P1 and P2 and the direction of the
magnetic field which will make the ions follow the path shown. 2
(b) (i) Show that ions passing through the slit S have a velocity v given by
E v
B
where the symbols have their usual meaning.
(ii) Explain what will happen to ions which have a speed greater than
this value. 2
(c) Calculate the velocity of ions passing through S. 2
(d) Describe and account for the shape of the path of the ions after passing
through S. 2
(e) Some ions form a trace on W at a point R. R is 190 mm from S.
Calculate the mass of one of these ions. 3
(11)
Physics: Course Questions (Advanced Higher) 17
19. A battery of e.m.f. 10V and negligible internal resistance is connected to a
data capturing device and a coil of wire as shown in the circuit diagram
below.
S
data capture device to
measure the current
When the switch is closed, the data capturing device measures the current at
intervals of 0.1 ms.
The current in the circuit is found to vary over the first millisecond as shown
in the graph below.
Physics: Course Questions (Advanced Higher) 18
19. continued
(a) Switch S is closed. The coil produces a back e.m.f.
(i) State the size of the back e.m.f. at this time.
(ii) Explain why the back e.m.f. opposes the battery e.m.f. 2
(b) Use the graph to determine:
(i) the initial rate of change of current
(ii) the self inductance of the coil 4
(c) The final steady current in the circuit is 25 mA.
(i) Find the resistance of the coil.
(ii) Calculate the energy stored in the inductor when the current is at its
maximum. 4
(d) A coil of negligible resistance is connected to a variable frequency
sinusoidal a.c. supply. Sketch a graph showing how the current in the
coil varies with frequency. The amplitude of the output voltage from the
supply is constant. 1
(11)
20. (a) The magnetic induction B at a distance r from an infinitely long straight
wire carrying a current I is given by
I B
0
2 r
Derive the expression for the force per unit length between two long
parallel wires carrying currents I1 and I2 at a distance r apart. 2
(b) A long horizontal cable P lying in a North-South direction provides the
electricity supply to an industrial process. The cable carries a current of 200 A in the direction from North to South. The vertical component of
the Earth’s magnetic field is 4.36 10-5
T.
(i) What is the size and direction of the force per unit length acting on
the wire due to the vertical component of the Earth’s magnetic field?
(ii) A second identical cable Q is laid parallel to and at a distance of
1.5 m from cable P in the same horizontal plane. Cable Q carries a
current of the same size and in the same direction as the current in P.
What is the size and direction of the force per unit length acting on P
due to Q? 6
(8)
Physics: Course Questions (Advanced Higher) 19
0
21. (a) Two point charges Q1 and Q2 are separated in air by a distance r.
Write down an expression for the force acting on charge Q2. 1
(b) A negative pion is made up of a d quark and a u antiquark. The electric
charge on the d quark is 1/3 e and that on the u antiquark is 2/3 e where e
is the charge on an electron.
(i) The distance between the quark-antiquark pair is 1.0 10-15
m.
Calculate the electric force between the quark-antiquark pair in the
pion.
(ii) Name the force which holds this quark-antiquark pair together. 3
(c) The figure below shows a charge q travelling directly towards a fixed
stationary charge Q. Charge q is initially travelling with a velocity v.
+ v +
q Q
Show that, for a head on collision, the distance of closest approach, rc is
given by
rc
2 mv 2
where m is the mass of charge q and 0 is the permittivity of free space. 2
(d) An alpha particle of mass 6.7 10-27
kg is moving with an initial
velocity of 1.0 107
m s-1
directly towards a fixed stationary gold nucleus. The atomic number of gold is 79.
Find the distance of closest approach of the alpha particle to the gold
nucleus. 2
(e) (i) Explain why the radii of all atomic nuclei are very tiny.
(ii) Name the force associated with beta decay in radioactive nuclei. 3
(11)
Physics: Course Questions (Advanced Higher) 20
WAVE PHENOMENA
22. (a) (i) Explain what is meant by a stationary wave.
(ii) State the differences between a travelling wave and a stationary
wave. 3
(b) (i) Explain why the relationship
x y a sin 2
ft
represents a travelling wave.
(ii) A travelling sound wave is represented by the expression
p 2 sin 330t x
where p is the pressure variation in pascals and the other symbols
have their usual meanings.
Find
(A) the wave frequency
(B) the wavelength
(C) the wave speed. 6
(10)
23. (a) A source of sound waves of frequency f is moving towards a stationary
observer. Show that the frequency detected by the stationary observer is
given by
f f v
. v vs
where v is the speed of sound in the medium and vs is the speed of the
source of sound waves relative to the observer. 2
(b) A car has a siren emitting a note of frequency 550 Hz. The car is
travelling at 45 m s-1
towards a stationary observer.
(i) Calculate the frequency of the sound heard by the observer as the car
approaches.
(ii) What frequency will be heard by the observer after the car has
passed the observer? 4
(c) In a gas discharge tube, moving gas atoms emit light after being put into
an excited state by passing a current through the gas.
(i) State the effect on the frequency of the light observed by a stationary
observer in
(A) the direction in which the atom producing the light is moving
(B) the direction opposite to that in which the atom producing the
light is moving.
(ii) Explain briefly why cooling the discharge tube would have the effect
of making the light emitted more monochromatic. 3
(9)
Physics: Course Questions (Advanced Higher) 21
24. (a) (i) State the conditions for two light beams to be coherent.
(ii) The conditions for coherence are usually more difficult to satisfy for
light than for sound.
Explain why this is so. 2
(b) Interference fringes may be formed by division of amplitude when light
from an extended source is incident normally on a thin wedge shaped
film.
(i) State what is meant by ‘division of amplitude’.
(ii) There is no coherence between light waves originating from
different points on an extended source. Explain why an extended
source can be used to produce interference fringes.
(iii) Show that the distance x between fringes formed by a thin film
whose thickness increases by an amount D over a length L is given
by
x
L
2nD
where is the wavelength of the light in a vacuum (or air) and n is
the refractive index of the medium of the film. 5
(c) Two optically flat glass plates of length 125 mm are separated at one end
by a hair as shown in the figure below. This forms a thin air wedge.
hair
Light of wavelength 589 nm illuminates the plates from above.
At the line of contact of the glass plates there is a dark fringe.
A further 55 dark fringes are counted in a distance of 50.3 mm.
(i) Explain why there is a dark fringe at the point of contact of the glass
plates.
(ii) Calculate the thickness of the hair.
(iii) State what would happen to the fringes if the space between the
glass plates was filled with water, rather than air. 5
(12)
Physics: Course Questions (Advanced Higher) 22
25. White light is reflected normally from one part of a soap film with
surfaces A and B as shown in Figure 1. The refractive index of the soap
film is 1.38.
Figure 1
The light is then focussed on to the slit of a spectrometer as shown in
Figure 2.
Figure 2
The first order spectrum observed has a dark band with a minimum intensity
at an angle corresponding to a wavelength (in air) of 578 nm.
(a) (i) State what is meant by the optical path difference between waves
reflected from the two surfaces A and B of the film.
(ii) Explain how the absence of light at 578 nm can be accounted for by
interference effects in the thin film.
(iii) Calculate the minimum thickness of soap film consistent with a dark
band at 578 nm. 5
(b) White light is reflected normally from a different part of the film and the
position of the dark band in the first order spectrum is found to be closer
to the red end of the spectrum.
Explain what information this gives about the difference in film
thickness between the two positions used for reflection. 2
(e) After the conclusion of the experiment it was noticed that a black band
formed across the film at the top of the film and increased in width until
it extended over most of the film just before the film broke.
Explain this observation. 2
(9)
Physics: Course Questions (Advanced Higher) 23
26. The figure below shows a non reflective coating for a lens. This coating
produces destructive interference of the reflected beams at normal
incidence.
(a) Derive a relationship between the minimum thickness d of the coating,
the wavelength of the light in air and the refractive index n of this
coating. 2
(b) Magnesium fluoride is used as a non reflective coating for a lens. The
refractive index of magnesium fluoride for a wavelength of 550 nm is
1.38. Calculate the thickness of magnesium fluoride required to produce
destructive interference for light of wavelength 550 nm. 2
(c) Explain what effect the coating will have on the intensity of transmitted
light. 2
(d) The lens is illuminated with white light and viewed in the reflected light.
Describe and explain the appearance of the lens 2
(8)
27. When unpolarised light is incident on the surface of water at the Brewster
angle, the reflected light is polarised.
(a) Explain what is meant by ‘light is polarised’. 1
(b) Explain why sound is not polarised by reflection. 1
(c) Calculate Brewster’s angle for monochromatic light reflected from water.
The refractive index of water is 1.33 for this light.
2
(d) Suggest why polarising sunglasses might be of use to a trout fisherman. 1
(5)
Physics: Course Questions (Advanced Higher) 24
28. A source of monochromatic light is placed behind two narrow slits
separated by 0.25 mm. A light detector, 2.5 m in front of the slits, is
moved from X to Y as shown in the figure below.
As the detector moves from X to Y, a series of maximum and minimum
readings is observed.
The distance of the detector from X for each maximum reading is recorded
in Table I.
Table 1
Order of maximum reading 0th
1st
2nd
3rd
4th
5th
Distance from X/mm
0
6.9
14.1
21.0
27.9
35.0
(a) (i) Show that the fringe spacing x for an experimental arrangement
of this type is given by the expression
D x
d
where the symbols have their usual meaning.
(ii) Calculate the wavelength of light used in the experiment. 4
(b) The experiment is repeated using a different colour of light and the
results are shown in Table 2.
Table 2
Order of maximum reading 0th
1st
2nd
3rd
4th
5th
Distance from X/mm
0
6.0
12.0
17.9
24.0
30.1
(i) State how the wavelength of this light compares with that used in
the original experiment.
(ii) Suggest one way in which the experimental arrangement could be
changed so that the separation of the maximum readings returned
to those in Table I. 2
(6)
Physics: Course Questions (Advanced Higher) 25
DATA
Common Physical quantities
QUANTITY
SYMBOL
VALUE
Gravitational acceleration Radius of Earth
Mass of Earth
Mass of Moon
Mean radius of Moon orbit Universal constant of gravitation
Speed of light in vacuum
Speed of sound in air
Mass of electron
Charge on electron
Mass of neutron
Mass of proton
Planck’s constant
Permittivity of free space
Permeability of free space
Refractive index of water
of perspex
g
RE
ME
MM
G
c v
me
e
mn
mp
h
0
0
n
n
9.8 m s-2
6.4 x 106
m
6.0 x 1024
kg
7.3 x 1022
kg
3.84 x 108
m
6.67 x 10-11
m3
kg-1
s-2
3.0 x 108
m s-1
3.4 x 102
m s-1
9.11 x 10-31
kg
-1.60 x 10-19
C
1.675 x 10-27
kg
1.673 x 10-27
kg
6.63 x 10-34
J s
8.85 x 10-12
F m-1
4 x 10-7
H m-1
1.33
1.5
The solutions to the questions use the data values given above.
Physics: Course Questions (Advanced Higher) 34