Post on 28-Feb-2019
pellenc s.a.Route de Cavaillon
B.P. 4784122 PERTUIS cedex
(France) Tel : +33(0)4 90 09 47 00 Fax : +33(0)4 90 09 64 09E-mail : pellenc.sa@pellenc.com
www.pellenc.com
54_74976_J - 12/2014
POLETELESCOPIC
USER GUIDE
ENGTranslation of the original user guide
CONTENTS:
READ THE USER GUIDE CAREFULLY BEFORE USING THE TOOL
• A hedge trimmer without blade• A power cord for the battery• A torx screwdriver• A user guide• 1 armband• 3 spare screws (cutting head)• The warranty card• 2 carrying kits (Helion Telescopic only)
2
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3GENERAL SAFETY INSTRUCTIONS FOR THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SAFETY WARNING FOR THE HEDGE TRIMMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5SAFETY MEASURES FOR THE CHARGER AND THE BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY INDICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6SAFETY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6SAFETY INDICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6ACCESSORIES SUPPLIED WITH THE BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DESCRIPTION AND TECHNICAL CHARACTERISTICS “POLE” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7TECHNICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DESCRIPTION AND TECHNICAL CHARACTERISTICS “TELESCOPIC”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8TECHNICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PUTTING THE TOOL INTO SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9USING THE HANDLE TRIGGERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9POSITION OF THE FRONT HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9ANGLE OF THE CUTTING HEAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9ADJUSTING THE TELESCOPIC POLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10STARTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11HOLDING THE TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
STARTING AND USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12SPEED SELECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12TRIMMER BLADE PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12CHOICE OF TRIMMER BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13SERVICING SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14PELLENC TOOL MAINTENANCE RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14GREASING THE TRIMMER BLADE REDUCTION GEAR (LEVEL 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15TIGHTENING THE BLADES (LEVEL 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15SHARPENING THE BLADES (LEVEL 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15LUBRICATING THE BLADES (LEVEL 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16ACCESSORIES AND CONSUMABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16STORAGE OUT OF SEASON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16REPLACING THE TRIMMER BLADE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
INCIDENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
«PELLENC SA» TERMS OF WARRANTY AND NON-RESPONSIBILITY CLAUSE . . . . . . . . . . . . . . . . . . . . . . . 20
"EC" DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table of contents
3
INTRODUCTION
ENVIRONMENTAL PROTECTIONYour equipment comprises numerous materials which can be valorised or recycled. Entrust these to your reseller or to an approved service centre so that they can be processed.
Comply with the regulations in force in your country as concerns environmental protection associated with your activity.
All through this user guide you will find advisory notes and information entitled: REMARK, CAUTION / WARNING.
A REMARK provides additional information, clarifies a point or explains a step to be followed in detail.
The CAUTION and WARNING advisories are used to define a procedure which, if neglected or incorrectly performed, may lead to serious damage to the equipment and/or personal injury.
This advisory: G indicates that if the procedures or instructions are not complied with, any damage will not be covered by the warranty and the owner will be responsible for the repair costs.
Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify and read these indications before using the tool. Immediately replace any indications that may become partially illegible or deteriorated.
Refer to the «SAFETY INDICATIONS» heading in order to identify the location of the safety indications on the tool.
No part of this manual may be reproduced without the written consent of PELLENC S.A.. The technical characteristics and the illustrations given in this manual are for information purposes and are in no way contractual. PELLENC S.A. reserves the right to make any modification or improvement to its products as deemed necessary without informing customers already in possession of a similar model. This manual forms an integral part of the tool and must accompany the tool if it changes hands.
SAFETY INSTRUCTIONS
You must read THE WHOLE of this user guide before using the tool or before carrying out servicing operations.Comply scrupulously with the instructions and illustrations given in this document.
KEEP THESE INSTRUCTIONSThis manual contains important information and operating instructions for the following tool : HELION Pole & Telescopic
4
SAFETY INSTRUCTIONS
• The HELION hedge trimmer is a professional tool reserved exclusively for trimming bushes and hedges.• PELLENC S.A. declines all responsibility in case of damage caused by improper use and use other than for which it is intended.• PELLENC S.A. also declines all responsibility in case of damage caused by the use of non-genuine parts or accessories.
GENERAL SAFETY INSTRUCTIONS FOR THE TOOL
CAUTION Read all the safety measures and all the instructions.Retain all the safety measures and instructions for later reading.
Work area safetya. Keep the work area clean and well lit. b. Do not use electric tools in an explosive atmosphere, for example in the presence of flammable
liquids, gases or dust. c. Keep children and persons present away when using the tool.
Electrical safetya. The plugs of the electric tool must be adapted to the base. Never modify the plug in any way
whatsoever. Do not use adaptors with grounded tools. b. Avoid any body contact with grounded surfaces such as pipes, radiators, cookers and refrigerators. c. Do not expose tools to rain or damp conditions. d. Do not misuse the power cord. Never use the power cord to carry, pull or disconnect the tool. Keep
the power lead away from heat, lubricant, sharp edges or moving parts. e. When using a tool outdoors, use an extension adapted to outdoor use. f. If you must use a tool in a damp place, use power supply protected by a residual current device
(RCD). Personal safety
a. Remain vigilant, watch what you are doing and use common sense when using the tool. Do not use a tool if you are tired or under the influence of drugs, alcohol or medication.
b. Wear safety equipment. Always wear eye protection.c. Avoid any untimely starting of the device. Make sure the switch is in the off position before connecting
the tool to the mains and/or battery pack, picking it up or carrying it. d. Remove any adjustment key before starting the tool. e. Do not rush. Adopt a suitable position and remain balanced at all times.f. Wear appropriate clothing. Do not wear loose clothing or jewellery.g. Keep hair, clothing and gloves away from moving parts. h. If systems are provided to connect dust extraction and recovery equipment, make sure these
systems are connected and properly used.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or preliminary instructions by a person responsible for their safety.
KEEP THESE INSTRUCTIONS
5
56_1
0_01
6A
SAFETY MEASURES FOR THE CHARGER AND THE BATTERY
Refer to the Pellenc tools battery manual.
SAFETY INSTRUCTIONS
SAFETY WARNING FOR THE HEDGE TRIMMER
1– Keep the cutting blade away from all parts of your body. Do not remove the cut material or hold the material to be cut when the blades are moving. Make sure that the switch is closed when removing the stuck material.2– Carry the hedge trimmer by the handle with the cutting blade off. Always fit the protective sheath on the cutting device during transport or storage of the hedge trimmer.3– Hold the tool by the isolated gripping areas only because the cutting blade can get in contact with the hidden wiring or the own hedge trimmer power cord.4– Keep the cable away from the cutting area.
WARNING:Before working on the tool, check that the On / Off switch is in the off position «0» and disconnect the battery power lead.
Tool usage and maintenancea. Do not force the tool. Use a tool suited to your application. b. Do not use the tool if the switch does not allow it to be switched on and off. c. Disconnect the plug of the power supply source and/or battery pack from the tool prior to any
adjustment, change of accessories or before putting the tool away. d. When not in use, keep tools out of reach of children, and do not allow persons to use the tool if they
do not know how to use it and if they have not read these instructions. e. Comply with tool servicing instructions. Check that the moving parts are not misaligned or jammed,
that there are no broken parts or that there is no other condition which could affect the operation of the tool. In the event of damage, have the tool repaired before using it.
f. Keep the cutting components sharp and clean. g. Use the tool, accessories, blades etc., in accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of battery-operated tools and usage precautions.
a. Only recharge using the charger specified by the manufacturer.b. Only use the tools with specifically designated battery packs.c. When a battery pack is not used, store it away from other metal objects such as paper clips, coins,
keys, nails, screws or other small items which can form a connection from one terminal to another.d. In poor conditions, liquid can be ejected from the battery; avoid any contact. In the event of accidental
contact, clean with water. If the liquid gets into your eyes, seek medical help.Maintenance and upkeep
a. Have the tool serviced by a qualified repairer using only identical spare parts.
6
1 5
2 6
3 7
4 8
54_08_038C
1
2
3
4
5
6
7
SAFETY INDICATIONS
SAFETY EQUIPMENT
Protective equipment Wearing is1 Helmet Recommended2 Visor Recommended3 Hard-wearing gloves Mandatory4 Safety footwear Recommended5 Ear protection Mandatory6 Safety goggles Mandatory7 Safety jacket or over-sleeves Recommended8 Work trousers Recommended
SAFETY INDICATIONS
1– LwA sound power level guaranteed.2– Read the user guide.3– Goggles and ear defenders are compulsory.4– Gloves are compulsory.5– Risk of burns (motor).6– Electrically conductive materials. Stay at least 10 meters (33 ft) away from all electrical sources.7– Do not expose to rain.
- One grease tube - 3 x M5x30 screws - Protective sheath - Assembly instructions - The blade's certificate of conformity
ACCESSORIES SUPPLIED WITH THE BLADE
7
54_10_002B
1
2
3
7 965
4
11
10
8
DESCRIPTION AND TECHNICAL CHARACTERISTICS “POLE”
TECHNICAL CHARACTERISTICS
1– Handle2– Starting trigger3– Safety trigger4– Speed selector5– Power ON light and speed indicator6– Front handle7– Motor
8– Pole9– Blade guide and blades10– Anti-kickback fitting11– Head orientation knob
PoleModel HP 27 HP 51 HP 63 HP 75 HP 63 DPower 1200 WattsWeight 3.4 Kg (7.5 lb) 3.6 Kg (7.9 lb) 3.7 Kg (8.2 lb) 3.8 Kg (8.4 lb) 3.8 Kg (8.4 lb)Dimensions (L x w x H) in mm 1425
*85*1301665
*85*1301785
*85*1301905
*85*1301785
*145*130
Useful cutting length / Blade guide 270 mm 510 mm 630 mm 750 mm 630 mm
Distance between teeth 33 mmTooth height 24 mmBlade speed 3200 to 3800 strokes/mnTilting cutting head 130° (-45° / +85°)Working capacity (time) According to use and battery type
Vibration emission value as per EN 60745-2-15 :2009handle ah = 5,5 m/s²
uncertaintyKd = 1,5 m/s²
Determining the sound levels and vibration rates is based on the operating conditions at the maximum nominal rating.
Maximum A-weighted sound pressure level (ref. 20 µPa) at the position of the user LpA = 87 dB(A) K = 3 dB(A)
C-weighted peak sound pressure (ref. 20 µPa) at the position of the user LpC < 130 dB(C)
Values defined as per sound measurement standards NF EN ISO 11201 and NF EN ISO 3744.
Symbol Value Unit Reference Comment
LWAm 95,3 dB(A) 1 pW Measured sound power level
LWAg 96 dB(A) 1 pW Guaranteed sound power level The recording of the measured sound power level and of the guaranteed sound power level has been performed according to a procedure in accordance with directive 2000/14/CE appendix V.
8
54_14_001A
1
2
3
7 96
548
11 12
10
DESCRIPTION AND TECHNICAL CHARACTERISTICS “TELESCOPIC”
TECHNICAL CHARACTERISTICS
1– Handle2– Starting trigger3– Safety trigger4– Speed selector5– Power ON light and speed indicator6– Front handle7– Motor
8– Pole lock9– Blade guide and blades10– Anti-kickback fitting11– Pole12– Head orientation knob
TelescopicModel HT 27 HT 51 HT 63 HT 75 HT 63 DPower 1200 WattsWeight 3.8 Kg (8.4 lb) 4.2 Kg (8.8 lb) 4.3 Kg (9 lb) 4.5 Kg (9.3 lb) 4.4 Kg (9.3 lb)Dimensions (L x w x H) in mm 1610
*85*1301850/2300
*85*1301970/2420
*85*1302090/2540
*85*1301970/2420*145*130
Useful cutting length / Blade guide 270 mm 510 mm 630 mm 750 mm 630 mm
Distance between teeth 33 mmTooth height 24 mmBlade speed 3200 to 3800 strokes/mnTilting cutting head 130° (-45° / +85°)Working capacity (time) According to use and battery type
Vibration emission value as per EN 60745-2-15 :2009handle ah = 3,9 m/s²
uncertaintyKd = 1,5 m/s²
Determining the sound levels and vibration rates is based on the operating conditions at the maximum nominal rating.
Maximum A-weighted sound pressure level (ref. 20 µPa) at the position of the user LpA = 83 dB(A) K = 3 dB(A)
C-weighted peak sound pressure (ref. 20 µPa) at the position of the user LpC < 130 dB(C)
Values defined as per sound measurement standards NF EN ISO 11201 and NF EN ISO 3744.
Symbol Value Unit Reference Comment
LWAm 91,5 dB(A) 1 pW Measured sound power level
LWAg 96 dB(A) 1 pW Guaranteed sound power level The recording of the measured sound power level and of the guaranteed sound power level has been performed according to a procedure in accordance with directive 2000/14/CE appendix V.
9
54_08_037A
1
2
1
2
3
54_08_021A
56_1
0_01
6A
G
G
G
54_13_003A
3
1
2
1
PUTTING THE TOOL INTO SERVICE
A. Press the safety trigger (1) with the palm of your hand.B. Press the starting trigger (2).C. Release the starting trigger (2) to stop the tool motor.
USING THE HANDLE TRIGGERS
WARNING:Check that the safety devices operate correctly before starting work.
POSITION OF THE FRONT HANDLE
A. Loosen the locking thumb-wheel.B. Position the head in the desired working position.C. Retighten the locking thumb-wheel.
ANGLE OF THE CUTTING HEAD
WARNING:Never work without the locking thumb-wheel fully tightened.
WARNING: Never disable the tool safety devices.
ASSEMBLY:• Install the adjuster knob (2) and front handle (3) with the 2 delta (1).
• Lock the adjustment wheel (2) to block the position of the front handle on the tool.
DISASSEMBLY:• Unlock the adjuster knob (2).
• Unscrew the 2 delta (1) and remove the front handle (3) and adjuster knob (2).
10
!
51_1
1_00
1A
ADJUSTING THE TELESCOPIC POLE
Release the locking thumb-wheel.
Adjust the pole to the desired length.
Keep the head of the hedge trimmer in line with the handle.
Fully tighten the locking thumb-wheel.
Always make sure that the switch is in the OFF position «0» and that the battery is disconnected before adjusting the pole.
PUTTING THE TOOL INTO SERVICE
11
54_08_013C
21
54_08_014A
G
G
PUTTING THE TOOL INTO SERVICE
A. Put the tool into its working position. Remove the protector from the trimmer blade.B. Set the Pellenc tool battery ON/OFF switch to the ON position «I».
From this moment the tool is supplied with electrical power and it is ready to operate.
C. Press the starting trigger (1) and the safety trigger (2).The trimmer blade then operates as long as you keep the starting trigger (1) pressed.
STARTING
WARNING! Never cut anything other than vegetation.
CAUTION:Blade run-in must be carried out for 1 minute off-load at each change-over.Check the tightness of the trimmer blade after running in.
HOLDING THE TOOL
CAUTION:Never disconnect the electrical lead from the battery without checking that the ON/OFF switch is in the OFF position «0».
Your tool is equipped with a Pellenc-designed electric motor. This motor keeps the speed constant off load and when working.Let the hedge trimmer work without over-forcing.Always start the motor before bringing the trimmer blade into contact with the wood.
If at least 1 light on the handle is lit, the tool is suppied with electrical power.
1– Hold the tool by the rear and front handles and check that nothing is touching the trimmer blade.2– Attach the power cord to the arm using the armband supplied.3– The hedge trimmer is in its starting position.
12
54_08_036A
x1 x2
x3 x4
54_08_022A
56_1
0_01
6A
54_10_001B
56_1
0_01
6A
STARTING AND USE
SPEED SELECTOR
TRIMMER BLADE PROTECTION
CHOICE OF TRIMMER BLADE
Reduce the speed for a longer working capacity or when at least one light fl ashes.
The choice of trimmer blade depends on the desired work as regards cutting quality.
H27 / H51 / H63 / H75
Upkeep and fi ne trimming
H63D Increased hedge trimming cleanliness
There exist four blade lengths and a single rake blade with baffl e plate.
Fit the trimmer blade protector when transporting, adjusting, handling and storing the tool.
Your tool is equipped with a speed selector system. The speed selector is located on the handle and allows you to optimize the desired quality of work.Four lights located on the handle indicate the selected speed level.These lights may fl ash when the temperature of the tool approaches the safe temperature limit.
1 light lit Speed 1 (3200 strokes / mn)
2 lights lit Speed 2 (3400 strokes / mn)
3 lights lit Speed 3 (3600 strokes / mn)
4 lights lit Speed 4 (3800 strokes / mn)
13
SERVICING
SERVICING SCHEDULE
Diffi
culty
leve
l:1
= C
an b
e pe
rform
ed b
y th
e us
er2
= C
an b
e pe
rform
ed b
y ap
prov
ed d
istri
buto
r
Ele
men
ts c
once
rned
Ope
ratio
ns
Freq
uenc
y
Diffi
culty
Not
es
Prio
r to
each
us
eA
fter e
ach
use
Eve
ry 5
0 ho
urs
Whe
n ne
cess
ary
Gen
eral
app
eara
nce
Visu
al in
spec
tion
XX
1
Cle
anin
gX
1
Bla
de
Cle
anin
gX
1Ve
ry im
porta
nt D
irect
ly a
ffect
s co
nsum
ptio
n (a
uton
omy)
.U
se P
ELL
EN
C c
lean
er re
f. 73
974
Lubr
icat
ion
XX
1
Scr
ews
X1
Bla
de s
crew
s: 3
.0 N
.m3
fixin
g sc
rew
s: 4
.0 N
.m (5
.0 N
.m m
ax)
Sha
rpen
ing
X2
45°
Adj
ustm
ent
X2
Hei
ght o
f the
pos
ts
Red
uctio
n ge
arG
reas
ing
X1
20g
max
. of P
ELL
EN
C g
reas
e re
f. 74
588
(sup
plie
d w
ith th
e cu
tter b
ar) o
r ref
: 115
174
Han
dles
/ Tr
igge
rsO
pera
tion
X1
Har
dwar
e (e
xclu
ding
bl
ade)
Tigh
teni
ngX
1
Bat
tery
Ple
ase
refe
r to
the
batte
ry o
pera
ting
inst
ruct
ions
14
54_08_016B
54_10_003A
56_1
0_01
6A56
_10_
016A
G
G
G
SERVICING
Keep your tool clean by cleaning it frequently with a damp cloth and compressed air. Pay particular attention to the parts in contact with the wood (blades and guide).
CLEANING
CAUTION:Never use solvents (Trichlorethylene, White-Spirit, gasoline, etc) to clean the tool.
CAUTION:The trimmer blade must be cleaned with a biodegradable PELENC spray product (P/N 73974) before and after use.
PELLENC TOOL MAINTENANCE RECOMMENDATIONS
• Read the user guide thoroughly before any intervention.• Disconnect the battery before any intervention.• Use products recommended by PELLENC.• Ask you approved PELLENC distributor in case of any problems.
Frequently clean vegetation residue from the guide pins
REMARK: Send the hedge trimmer for overhaul every 200 hours or at least once per year.When the tool is stored, it must be clean and the battery must be charged.
These parts must be replaced as a precautionary measure or at least once a year: - Protective plate ref. 71297 - Hardware kit ref. 75905 - Anti-rebound bumper, ref 108881 - Strip for cutterbar ref. 115233 (H 51), ref. 115234 (H 63 + H63D) ref. 115235 (H 75). - Seal, ref. 71306
15
20gr
54_08_017B
54_08_020A
56_1
0_01
6A56
_10_
016A
56_1
0_01
6A
SERVICING
GREASING THE TRIMMER BLADE REDUCTION GEAR (LEVEL 1)
TIGHTENING THE BLADES (LEVEL 1)
SHARPENING THE BLADES (LEVEL 2)
The trimmer blade reduction gear must be greased after 25 hours of use and every 50 hours.
WARNING! Always disconnect the hedge trimmer from the battery before working on the blades.
WARNING! Always disconnect the hedge trimmer from the battery before working on the blades.
Sharpen the blades little but often.Check the sharpness of the blades regularly during the first hours of work in order to determine the necessary sharpening frequency.
Ensure an angle of 45° on the blade during sharpening.
Unscrew the screw located under the trimmer blade reduction gear using a Torx 25 screwdriver.
Apply 20 grams of Pellenc grease (P/N 115174).
PELLENC recommends using the grease pump ref. 68518.
Check the tightness of the blades on a regular basis.
Tighten the screws to 3 Nm.
The clearance obtained between the blades must be between 0.2 and 0.4 millimeters.
16
54_08_018B
X1
X1
X2
X2
11 22
33 44
55 66
8877
54_13_002B
56_1
0_01
6A
G
SERVICING
LUBRICATING THE BLADES (LEVEL 1)
STORAGE OUT OF SEASON
• Make sure the tool is clean when it is stored.• Make sure the blade is sharp when the tool is stored.• Make sure the reduction gear is greased when the tool is stored.• Fit the blade protector during transport and storage.
Lubricate the cutting blades 2 times a day using an oil can.
WARNING:Never use solvents (Trichlorethylene, White Spirit, petrol etc.) to lubricate the cutting blades.
HELION armband = ref.74338Harness carrying kit = ref.79297PELLENC Grease cartridge 400g = ref. 115174Belt carrying kit = ref.74668PELLENC biodegradable cleaner = ref. 73974Counterweight = ref.8666910.3 m extension = ref. 100994grease pump = ref. 68518
ACCESSORIES AND CONSUMABLES
COMMENT:PELLENC recommends using biodegradable chain oil in compliance with RAL-UZ-48 norm (ref. 85920 or, by default, any oil in compliance with RAL-UZ-48 norm)
17
54_08_039A54_08_039A
4 Nmmax.
G
SERVICING
REPLACING THE TRIMMER BLADE
WARNING:Before working on the tool, check that the ON/OFF switch is set to the OFF position «0» and disconnect the power supply lead from the battery.
Disconnect the power supply lead after moving the switch to the off position.
Unscrew the 3 screws using a Torx 25 screwdriver.
Fit the desired trimmer blade.
Torque tighten the 3 retaining screws to 4 Nm.
WARNING:Never use a trimmer blade other than the one specifi ed by PELLENC. Failure to do so will result in a risk of personal injury.
18
Rep
aire
d by
Use
r
App
rove
d P
ELL
EN
C
dist
ribut
or
Use
r
App
rove
d P
ELL
EN
C
dist
ribut
or
App
rove
d P
ELL
EN
C
dist
ribut
or
App
rove
d P
ELL
EN
C
dist
ribut
or
Solu
tions
Pre
ss th
e ba
ttery
sw
itch
(9)
Cha
nge
the
cord
Rec
harg
e th
e ba
ttery
Cha
nge
elec
troni
cs
boar
d if
the
diod
es
stay
off
afte
r tur
ning
on
and
che
ckin
g pr
evio
us p
oint
s
Cha
nge
the
trigg
er o
r se
nsor
Cha
nge
the
elec
troni
cs b
oard
Che
cks
Bat
tery
sw
itch
(9)
Che
ck th
e co
nditi
on o
f th
e co
rd
Che
ck th
at th
e ba
ttery
is
not
com
plet
ely
disc
harg
ed
At a
ppro
ved
PE
LLE
NC
dis
tribu
tor
prem
ises
At a
ppro
ved
PE
LLE
NC
dis
tribu
tor
prem
ises
At a
ppro
ved
PE
LLE
NC
dis
tribu
tor
prem
ises
Prob
able
cau
se
Bat
tery
off
The
pow
er c
ord
is c
ut
Bat
tery
Ele
ctro
nics
boa
rd
A tri
gger
no
long
er
wor
ks
Ele
ctro
nics
boa
rd
Con
ditio
n of
dio
des
Off
Off
On
Con
ditio
n of
bat
tery
on
/off
switc
h
0 I
Sym
ptom
s
The
tool
doe
s no
t sta
rt
INCIDENTS
19
Rep
aire
d by
Use
r
App
rove
d P
ELL
EN
C
dist
ribut
or
App
rove
d P
ELL
EN
C
dist
ribut
or
Use
r
Use
r
Sto
p, th
en re
star
t the
bat
tery
and
refe
r to
the
"Too
l doe
s no
t sta
rt" p
arag
raph
if n
eces
sary
.
Solu
tions
Cle
an th
e gu
ide
pins
Tigh
ten
to 3
.0N
.m
max
.
Cha
nge
the
casn
g
Red
uce
blad
e sp
eed
or p
ause
for a
whi
le
Allo
w th
e to
ol to
co
ol d
own
for
appr
oxim
atel
y 5
min
utes
Che
cks
Che
ck th
e co
nditi
on
of th
e gu
ide
pins
Tigh
ten
to 3
.0N
.m
max
.
Che
ck th
e sc
rew
st
uds
on th
e ca
sing
Flas
hing
dio
des
The
batte
ry b
eeps
4
times
Prob
able
cau
se
Clo
gged
gui
de p
ins
Tigh
teni
ng o
f bla
de
scre
w
Bro
ken
casi
ng
The
tool
is c
lose
to
its te
mpe
ratu
re li
mit
The
tool
has
reac
hed
its te
mpe
ratu
re li
mit
Con
ditio
n of
dio
des
On
Flas
hes
Off
Con
ditio
n of
the
batte
ry o
n/of
f sw
itch
I I I
Sym
ptom
s
The
blad
e m
akes
an
unus
ual n
oise
and
/or o
ff-lo
ad c
onsu
mpt
ion
exce
eds
200W
h af
ter 1
min
ute
of
oper
atio
n
The
diod
es fl
ash
durin
g us
e
The
tool
sto
ps d
urin
g us
e
INCIDENTS
20
«PELLENC SA» TERMS OF WARRANTY AND NON-RESPONSIBILITY CLAUSEMACHINE RANGE FOR OEP
In the event of failure of a mechanical part and subject to normal, rational use and maintenance in compliance with the maintenance manual, PELLENC S.A. guarantees its products for a period of ONE YEAR as of delivery; this time shall not exceed a period of 18 months following departure from the factory of the equipment under warranty : on one hand in accordance with the conditions stipulated in the warranties of PELLENC S.A. and on the other hand subject to the delivery report indicating the commissioning date was made known to PELLENC S.A.
In the event of an accident and total or partial destruction of the product, PELLENC S.A.’s warranty can only be granted, and their responsibility engaged, if the party claiming the warranty can provide technical proof specifying the origin of the accident, a defect in materials or a structural defect and the product components which are the cause of it.
This contractual warranty excludes any other responsibility of PELLENC S.A., whether implicit or explicit. For this reason, the responsibility of PELLENC S.A. can not exceed the limits defined above and covers, to a limited extent, repair or replacement, as chosen by PELLENC S.A., of parts recognized to be defective and, when applicable, the labour required to perform the repair or replacement on the basis of warranty time as defined by PELLENC S.A..
Any maintenance or repair work whatsoever carried out during the warranty period shall mandatorily be performed by PELLENC S.A. or by a PELLENC S.A. authorized dealer, under penalty of forfeiture of the warranty.
All costs arising from the immobilization, movement, approach and transport shall be, in all events, for the sole account of the purchaser.
As concerns parts or equipment that are not manufactured by PELLENC S.A., in particular ball screw, battery, etc., the warranty is limited to that of the suppliers to PELLENC S.A.. Normal wear parts worn out as the result of use are never under warranty.
PELLENC S.A. and the authorized dealer shall not be liable in the following cases:• Malfunctions due to faulty servicing, user inexperience or abnormal use.• Failure to perform overhauls and checks in accordance with manufacturer’s instructions.• Replacement of genuine parts or accessories with parts of accessories of another origin, or when the machine sold has been transformed or modified.
This warranty is explicitly limited to the terms defined above. PELLENC S.A. shall not be liable, under any circumstances, for payment of any indemnity for any reason whatsoever.
However, it is specified, in compliance with the provisions of decree No. 78.464 dated March 24th 1978, that this contractual guarantee does not replace the legal guarantee which obliges the seller to guarantee the buyer against the consequences of defects or hidden defects of the object sold.
21
MACHINES DIRECTIVE 2006/42/CE, APPENDIX IIA.
(ONLY CONCERNS EUROPE)
WE HEREBY DECLARE THAT THE EQUIPMENT HEREINAFTER REFERRED TO AS:
GENERIC DENOMINATION ELECTRIC POLE HEDGE TRIMMER
FUNCTION BATTERY POWERED ELECTRIC HEDGE TRIMMER INTENDED FOR PRUNING BUSHES / HEDGES
COMMERCIAL NAME HELION
TYPE HELION P/T
MODEL HELION POLE HELION TELESCOPIC
SERIAL No. 54P00001 - 4900054P50000 - 99999
COMPLIES WITH THE PERTINENT PROVISIONS OF THE MACHINES DIRECTIVE (2006/42/CE)
AND COMPLIES WITH THE PROVISIONS OF THE FOLLOWING OTHER EUROPEAN DIRECTIVES:2004/108/CE ; 2000/14/CE ; 2002/44/CE
Sound Level at the maximum operating rating
THE FOLLOWING HARMONIZED EUROPEAN STANDARDS WERE USED:EN ISO 10517 : 2009 ; EN 60745-1 : 2009 ; EN 60745-2-15 : 2009 ; EN 50260-1 : 2005
CONCLUDED AT PERTUIS, DATED 01/12/2014ROGER PELLENCCHIEF EXECUTIVE OFFICER
MANUFACTURER PELLENC S.A.ADDRESS QUARTIER NOTRE-DAME
ROUTE DE CAVAILLON - B.P. 4784122 PERTUIS CEDEX (FRANCE)
PERSON/ENTITY AUTHORISED TO COMPILE THE TECHNICAL DOSSIER
PELLENC S.A.
ADDRESS QUARTIER NOTRE-DAMEROUTE DE CAVAILLON - B.P. 4784122 PERTUIS CEDEX (FRANCE)
"EC" DECLARATION OF CONFORMITY
Model Symbol Value Unit Reference Comment
Pole LWAm 95.3 dB(A) 1 pW Measured sound power level
Pole LWAg 96 dB(A) 1 pW Guaranteed sound power level
Telescopic LWAm 91.5 dB(A) 1 pW Measured sound power level
Telescopic LWAg 96 dB(A) 1 pW Guaranteed sound power level The recording of the measured sound power level and of the guaranteed sound power level has been performed according to a procedure in accordance with directive 2000/14/CE appendix V.