Post on 04-Jun-2018
8/14/2019 Paretto analysis.ppt
1/26
By carrying out a Pareto Analysis, themanager is able to focus on training as an
issue, rather than spreading effort overtraining, taking on new staff members,and possibly installing a new computersystem.
1
8/14/2019 Paretto analysis.ppt
2/26
2. FlowchartsFlow charts are easy-to-understand
diagrams showing how steps in a
process fit together. This makes them useful tools for
communicating how processes work,and for clearly documenting how aparticular job is done.
Furthermore, the act of mapping aprocess out in flow chart format helpsyou clarify your understanding of theprocess, and helps you think aboutwhere the process can be improved.
2
8/14/2019 Paretto analysis.ppt
3/26
A flow chart is used to
Define and analyze processes;
Build a step-by-step picture of the processfor analysis, discussion, or communication;and
Define, standardize or find areas forimprovement in a process
3
8/14/2019 Paretto analysis.ppt
4/26
How to make a flow chart
Most flow charts are made up of threemain types of symbol:
Elongated circles, which signify the start orend of a process;
4
8/14/2019 Paretto analysis.ppt
5/26
Rectangles, which show instructions oractions; and
Diamonds, which show decisions thatmust be made
5
8/14/2019 Paretto analysis.ppt
6/26
Within each symbol, write down what thesymbol represents.
This could be the start or finish of theprocess, the action to be taken, or thedecision to be made.
Symbols are connected one to the other
by arrows, showing the flow of theprocess.
6
8/14/2019 Paretto analysis.ppt
7/26
Points to note
Flow charts are simple diagrams thatmap out a process so that it can easilybe communicated to other people.
To draw a flowchart, brainstorm thetasks and decisions made during aprocess, and write them down inorder.
Then map these out in flow chartformat using appropriate symbols for
the start and end of a process, foractions to be taken and for decisions
7
8/14/2019 Paretto analysis.ppt
8/26
Finally, challenge your flow chart to makesure that its an accurate representation
of the process, and that that it representsthe most efficient way of doing the job
8
8/14/2019 Paretto analysis.ppt
9/26
3. Check sheets
The intent and purpose of collectingdata is to either control the productionprocess, to see the relationshipbetween cause-and-effect, or for thecontinuous improvement of thoseprocesses that produce any type of
defect or nonconforming product.
A Check Sheet is used for the purposeof collecting data to compile in such away as to be easily used, understoodand analyzed automatically.
9
8/14/2019 Paretto analysis.ppt
10/26
The Check Sheet, as it is beingcompleted, actually becomes a
graphical representation of the data youare collecting, thus you do NOT need anycomputer software, or spreadsheet torecord the data.
It can be simply done with pencil andpaper
10
8/14/2019 Paretto analysis.ppt
11/26
The main functions -
Checks
Production process distribution checks -where the distribution lies.
Defective item checks - to determinewhat kind of defects exist in the process.
Defect location checks - to determinewhere the common defects on a part are
located.
11
8/14/2019 Paretto analysis.ppt
12/26
Defective cause checks - type of defectand thus validate the cause thereof.
Check-up confirmation checks - finalphase of assembly to check the finishedproduct or work.
12
8/14/2019 Paretto analysis.ppt
13/26
4. Histograms
The common person believes that if apart is made in mass production froma machine, all of the parts will beexactly alike.
The truth is that even with the best of
machines and processes, no two parts are
exactly the same. The product will have a main or "mean"
specification limit, with plus/minus tolerance
that states that as long as the part is
produced within this range, to that range, it is
an acceptable part.
13
8/14/2019 Paretto analysis.ppt
14/26
The object is to hit the targetspecification, however, that is notalways totally possible.
The purpose of a Histogram is to takethe data that is collected from aprocess and then display it graphicallyto view how the distribution of thedata, centers itself around the mean,or main specification.
14
8/14/2019 Paretto analysis.ppt
15/26
The histogram will graphically
show
The center of the data.
The spread of the data.
Any data skewness (slant, bias or run atan angle).
The presence of outliers (product outsidethe specification range).
The presence of multiple modes (orpeaks) within the data.
15
8/14/2019 Paretto analysis.ppt
16/26
5. Scatter diagrams
The Scatter Diagram is another QualityTool that can be used to show the
relationship between "paired data",and can provide more usefulinformation about a productionprocess.
What is meant by "paired data"? The term "cause-and-effect"
relationship between two kinds of datamay also refer to a relationshipbetween one cause and another, orbetween one cause and several
16
8/14/2019 Paretto analysis.ppt
17/26
For example, you could consider therelationship between an ingredient
and the product hardness; betweenthe cutting speed of a blade and thevariations observed in length of parts;or the relationship between the
illumination levels on the productionfloor and the mistakes made in qualityinspection of product produced.
17
8/14/2019 Paretto analysis.ppt
18/26
6. Control charts
Control charts are generally used in aproduction or manufacturing environment
and are used to control, monitor andIMPROVE a process.
Common causes are always present andgenerally attributed to machines, material
and time vs. temperature.
18
8/14/2019 Paretto analysis.ppt
19/26
This normally takes a minor adjustmentto the process to make the correction
and return the process to a normaloutput.
However, when making a change to the
process, it should always be a MINOR
change.
If a plot is observed that shows a slightdeviation trend upward or downward,the "tweaking" adjustment should be a
slight change, and then another
19
8/14/2019 Paretto analysis.ppt
20/26
Too often people will over-correct bymaking too big of an adjustment which
then causes the process to dramaticallyshift in the other direction.
For that reason, all changes to theprocess should be SLIGHT and GRADUAL!
20
8/14/2019 Paretto analysis.ppt
21/26
Control Lines
A control chart is a graph or chart withlimit lines, called control lines.
There are basically three kinds of controllines:
the upper control limit (UCL),
the central line (actual nominal size ofproduct),
the lower control limit (LCL).
21
8/14/2019 Paretto analysis.ppt
22/26
The Xbar & R Control Chart
An Xbar & R Control Chart is onethat shows both the mean value (X ), and the range ( R ).
The Xbar portion of the chart
mainly shows any changes in themean value of the process, whilethe R portion shows any changes
in the dispersion of the process.
22
8/14/2019 Paretto analysis.ppt
23/26
This chart is particularly useful inthat it shows changes in meanvalue and dispersion of the
process at the same time, makingit a very effective method for
checking abnormalities within theprocess; and if charted while inprogress, also points out a problemin the production flow in real time
mode.
23
8/14/2019 Paretto analysis.ppt
24/26
7. Fishbone diagram
Cause & Effect Diagrams
Identifying the Likely Causes of Problems
Also called Fish or Fishbone Diagram andIshikawa Diagrams
24
8/14/2019 Paretto analysis.ppt
25/26
Cause and Effect analysis helps you tothink through causes of a problem
thoroughly. Their major benefit is that they push you to
consider all possible causes of theproblem, rather than just the ones that are
most obvious
25
8/14/2019 Paretto analysis.ppt
26/26
Conclusion.
26