Post on 05-Aug-2020
1Z98SZZ002EN00 - 11-04-2019
OZ M0Orbital motors
Compact gerotor motors with radial distribution
Before use, carefully read the GENERAL INSTRUCTIONS FOR USE OF ORBITAL MOTORS.
2 Z98SZZ002EN00 - 11-04-2019
OZ M0
Displacement Pressure Torque Rotational speed
Max.flow rate
Max.outputpower
WeightContinuous Intermittent Peak Continuous Intermittent Peak
cm3/rev bar bar bar Nm Nm Nm min-1 l/min kW kg
08 8.2 100 140 200 11 15 21 1950 16 1.8 1.9
12 12.9 100 140 200 16 23 33 1550 20 2.4 2
20 19.9 100 140 200 25 35 51 1000 20 2.4 2.1
32 31.6 100 140 160 40 57 64 630 20 2.4 2.2
40 39.8 90 140 160 45 70 82 500 20 2.4 2.3
50 50.3 70 140 160 46 88 100 400 20 1.8 2.4
Intermittent conditions must not last more than 10% of each minute. Peak conditions must not last more than 1% of each minute.
HC_SUPERPART
HC_SUPERPART
HC_SUPERPART
HC_SUPERPART
HC_SUPERPART HC_SUPERPART
Displacement
Compact gerotor motor with radial distribution and axial roller bearings, suitable for use where high rotation speeds and small dimensions are required.
3Z98SZZ002EN00 - 11-04-2019
OZ M0
Flow ratel/min
Pressure bar
35 50 70 100 120 140
2 3228
5218
8206
10156
12111
1458
4 3474
5471
7463
11426
13391
15331
8 3953
5946
7926
11884
13855
15816
12 21444
51426
71402
101360
131324
151288
15 41912
71900
101861
121833
141780
20 62395
102350
112328
142281
Flow ratel/min
Pressure bar
30 50 70 85 100 120
2 1645
2740
3634
4428
5117
4 1696
2793
3785
4479
5265
6252
8 15197
26195
36182
44176
52166
63154
12 14293
25287
35282
43277
51268
62257
15 13371
24365
34360
42355
50347
62338
20 10497
21492
31487
39480
48472
59463
25 7622
19617
29612
37607
44600
56591
Flow ratel/min
Pressure bar
15 30 50 70 100
2 1137
2333
3627
5022
4 1176
2273
3668
5063
7055
8 11157
21154
35149
50145
71137
12 11237
20234
33231
49226
71218
15 10296
18295
32294
47288
69282
20 8395
14395
29393
44390
64381
25 4498
10496
25494
40490
59484
Flow ratel/min
Pressure bar
35 50 70 100 120 140
2 6140
8136
11119
1668
19111
4 6296
8289
12274
17229
19391
23145
8 5605
8596
12583
17543
20855
24469
12 5912
8905
11895
16859
201324
24784
15 51152
71144
111136
161102
191833
231036
20 31542
71532
101521
151500
192328
221437
25 21910
61891
91878
141848
181828
221788
08
20
40
12
32
50
PressureContinuous
PressureContinuous
PressureContinuous
PressureContinuous
Torque NmRotational speed min-1
Torque NmRotational speed min-1
Torque NmRotational speed min-1
Torque NmRotational speed min-1
PressureIntermittent
PressureIntermittent
PressureIntermittent
PressureIntermittent
Flow ratel/min
Pressure bar
17 35 50 70 100 120 140
2 399
996
1489
1974
2642
3021
4 4197
9191
14182
19178
26134
31112
3674
8 4398
9395
13391
19377
27340
31319
36288
12 3596
8594
13588
18579
26545
31523
37493
15 3745
8741
12738
17728
25695
30684
36660
20 1998
6995
11991
19985
24962
29916
35885
25 41247
91245
141242
231189
281180
331176
Flow ratel/min
Pressure bar
20 35 50 70 100 120 140
2 761
1557
2152
2847
4016
4 7126
15121
21114
29106
4182
4867
5749
8 7250
15244
21239
29231
41207
49194
58167
12 6378
13374
20369
28362
40338
48322
58297
15 4476
12472
18468
27462
39441
47429
57406
20 3633
10630
17627
25619
37601
46585
55566
25 1791
8789
15787
23783
35766
43753
52732
PressureContinuous
PressureContinuous
Torque NmRotational speed min-1
Torque NmRotational speed min-1
PressureIntermittent
PressureIntermittent
Performance
8.2 cm3/rev
19.9 cm3/rev
39.8 cm3/rev
12.9 cm3/rev
31.6 cm3/rev
50.3 cm3/rev
4 Z98SZZ002EN00 - 11-04-2019
OZ M0
The shafts come with anti-corrosion treatment as standard.
MK1
MP1 MP2
A
A
14
5 16 A-A
M6
Ø16 18Ø
17+0,0
06-0
,005
0 -0,1
3
5 0-0,03
0-0,0528,5
5 19,05
Ø17
14
0-0,0528,5
Ø15
.875
1/4-
28U
NF
0 -0,0
25
18-0
,10
-0,2
3
A-A 4,8 0-0,03
A
A
15
M6
Ø16
,5 0 -0
,11
Ø17
14 0-0,0528,5
A-A
A
A
Shaft profile
Grooved DIN 5482 17x14
Ø16 key DIN68885 A 5x5x16 5/8" key BS46 3/16"x3/16"x3/4"
Max. torque 39 Nm
Max. torque 46 Nm
Max. torque 39 Nm
5Z98SZZ002EN00 - 11-04-2019
OZ M0
C0
C0
mm mm
M08 3.5 104.5
M12 5.5 106.5
M20 8.5 109.5
M32 13.5 114.5
M40 17 118
M50 21.5 122.5
mm mm
M08 3.5 106
M12 5.5 108
M20 8.5 111
M32 13.5 116
M40 17 119.5
M50 21.5 124
The flanges come with anti-corrosion treatment as standard.
C1
mm mm
M08 3.5 104.5
M12 5.5 106.5
M20 8.5 109.5
M32 13.5 114.5
M40 17 118
M50 21.5 122.5
3-M6
5
10
L1L
4,5
34,5
45°
45°
Ø45
Ø31
,5
Ø60
±0,
2 0 -0,0
6
5L1
4,7
34,5 11,7
Ø60
±0,
2
Ø31
,5 0 -0
,06
45°
45°
L L
30,4
5 ±
0,15
3-M6
10Ø45
L1 4,5
Ø31
,5 0 -0
,06
45°
45°
34,5
5 L
Ø60
±0,
23-1/4”-28 UNFØ45
10
Flanges
EU rear ports
EU lateral ports
Type
Type
L
L
L1
L1
US rear portsType L L1
6 Z98SZZ002EN00 - 11-04-2019
OZ M0
C1
mm mm
M08 3.5 106
M12 5.5 108
M20 8.5 111
M32 13.5 116
M40 17 119.5
M50 21.5 124
The flanges come with anti-corrosion treatment as standard.
AI
AI
mm mm
M08 3.5 107
M12 5.5 109
M20 8.5 112
M32 13.5 117
M40 17 120.5
M50 21.5 125
mm mm
M08 3.5 108.5
M12 5.5 110.5
M20 8.5 113.5
M32 13.5 118.5
M40 17 122
M50 21.5 126.5
5L1
4,7
34,5 11,7Ø45
Ø60
±0,
245°
45°
L L
10
Ø31
,5 0 -0
,06
3-1/4”-28 UNF
32 5,5
L2 4,5L
Ø45
Ø80
Ø63
0 -0,0
5
Ø73,5 0-0,05
45°
45°
Ø60
±0,
2
2 ±0
,2
2-Ø9 ±0,2
Ø97
4,7
32 5,511,7
Ø63
0 -0,0
5
Ø60
±0,
2
LL2
2 ±0
,2
Ø45
45°
45°
2-Ø9 ±0,2
Ø80
Ø97
Ø73,5 0-0,05
US lateral portsType L L1
Flanges
Rear ports with flange
Lateral ports with flange
Type
Type
L
L
L2
L2
7Z98SZZ002EN00 - 11-04-2019
OZ M0
A-B T
3/8" BSPP 1/8" BSPP
A-B T
9/16" - 18 UNF 3/8" - 24 UNF
A-B T
3/8" BSPP 1/8" BSPP
Port combinations
Port
Port
Port
Port
Port
Port
MY1
MY2
MS1
TP(A,B)
15,2
±0,
3
10,5 ±0,15 ±0,1
15,2
±0,
3Ø
15,2
±0,
3
T
Ø15
,2 ±
0,3
P(A,B)
5 ±0,110,5 ±0,1
min
. 8m
in. 1
2
min
. 12
Ø17
Ø25 Ø25
BSPP 3/8”
BSPP 3/8”BSPP 3/8”
With rear ports
With rear ports
With lateral ports
8 Z98SZZ002EN00 - 11-04-2019
OZ M0
A-B T
9/16" - 18 UNF 3/8" - 24 UNF
Port combinations
Port Port
MY1 With lateral ports
min
. 8m
in. 1
2
min
. 12
Ø19
Ø25 Ø25
3/8”-24UNF
9/16”-18UNF9/16”-18UNF
9Z98SZZ002EN00 - 11-04-2019
OZ M0
0 L
A
B
B
A
A
B
B
A
Direction of rotation of shafts
Standard Reverse
When facing the motor shaft, rotation is: - Clockwise, when port A is pressurised- Counterclockwise, when port B is pressurised.
When facing the motor shaft, rotation is: - Counterclockwise, when port A is pressurised- Clockwise, when port B is pressurised.
10 Z98SZZ002EN00 - 11-04-2019
OZ M0 Permitted loads
Fa max 800 N
Fr
Axial load
Radial load
1400
1600
1800
200018001600140012001000800600400200
1000
800
600
400
200
0
1200
Fr (N)
min-1
0
10
20
3040
5060
7080
11Z98SZZ002EN00 - 11-04-2019
OZ M0Ordering instructions
1
2
4
5
3
Shaft profile
Thread ports A-B, T
08 8.2 cm3/rev
12 12.9 cm3/rev
20 19.9 cm3/rev
32 31.6 cm3/rev
40 39.8 cm3/rev
50 50.3 cm3/rev
MP1 Cylindrical Ø16 - Key DIN 68885 A 5x5x16 MP2 Cylindrical 5/8" - Key BS46
3/16"x3/16"x3/4" MK1 Grooved DIN 5482 17x14
C0 EU version rear and lateral ports C1 US version rear and lateral
ports AI Rear and lateral ports with flange
00 Standard
MY1 With rear ports3/8" BSPP, 1/8" BSPP MY2 With rear ports
9/16"-18 UNF, 3/8"- 24 UNF MS1 With lateral ports3/8" BSPP, 1/8" BSPP MS2 With lateral ports
9/16"-18 UNF, 3/8"- 24 UNF
Flanges
Special options
Displacement
6
0 Standard L Reverse
Direction of rotation of shafts
1 2 3 4 5 6
OZ M0