Post on 15-Mar-2021
Machinery CatalogMachinery Catalog
52 Race Street, Macungie PA 1806252 Race Street, Macungie PA 18062Phone: 1-800-808-0454Phone: 1-800-808-0454Email: buydirect@bdimachinery.netEmail: buydirect@bdimachinery.netwww.bdimachinery.netwww.bdimachinery.net
52 Race Street, Macungie PA 18062Phone: 1-800-808-0454Email: buydirect@bdimachinery.netwww.bdimachinery.net
Nursery EditionNursery EditionNursery Edition
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 1
The CIMA Advantage:The technological delivery system is able to treat more area of canopy with less water. The simple transmission requires less maintenance and the fan absorbs less horsepower than conventional air-blast sprayers. All CIMA’s can be fitted with a custom spray-head to target the treatment into the canopy with minimal over-spray.
LOW VOLUME AIR SPRAYERSLOW VOLUME AIR SPRAYERS
All CIMA spray heads can be easily adjusted to direct the spray into the crop with minimal overspray. Each spray outlet uses a venturi (no nozzle tips with air shear nozzle) to produce consistently fine 100-150u size droplets (no tips). Calibration only takes seconds since each spray head uses the CIMA quick change 15 position “dial-a-rate” calibration disc.
The Low Volume Venturi style sprayer makes droplets in the 100-150u Range. A high-pressure sprayer commonly makes droplets in the 250-400u range. Since droplets are three dimensional, when you break down a large droplet it has 8x smaller droplets inside of that large droplet, therefore you will have many available for better coverage. This type of spray method also allows you not to have to spray to a drip unlike typical high-pressure sprayers. The venturi style delivery system coats all surfaces of the canopy with air speeds around 170-200 mph. Achieving a better quality of coverage, and yielding a cleaner crop.
Better Coverage with Less Water
Targeted Spray
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-04542
LOW VOLUME AIR SPRAYERSLOW VOLUME AIR SPRAYERS
3 Point Sprayers
CIMA’s featured ergonomic design makes it possible to use smaller versatile tractor. Choice of several target heads to treat any canopy. All models are standard with internal mixing basket and a safety fresh water tank. Calibration is easy and quick with CIMA’s “Dial-a-rate” along with target control head, and air shear delivery system you will use minimal active chemical to achieve great coverage.
The 5x5 head is ideal for close rows or a dense canopy that needs to get coverage deep into the canopy.
MODEL/GAL. HP LBS CONTROLS
P42/80 20 397 ManualP45/100 35 419 ManualP50/100 45 497 ManualP50/165 50 550 ManualP55/165 70 596 ElectricEMV/P – Electric motor valves upgrade for P42/45/50
SPECS FOR ALL CIMA SPRAYERSSPECS FOR ALL CIMA SPRAYERS
P42 P45, & T45 P50, S50, & T50 P55, & T55AIR VOLUME (CFM) 2354 3178 4444 9123AIR SPEED (MPH) 180-185 180-185 180-185 180-185FAN DIAMETER 18” 18” 20” DUAL WIDE 22”FAN RPMS 4000 4500 4000 3900
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 3
LOW VOLUME AIR SPRAYERSLOW VOLUME AIR SPRAYERS
Trailer Sprayers
CIMA’s trailer sprayers range from 200-525 gallons, and have a spray head available for virtually any crop. Low volume atomization delivery system will treat more canopy with 2/3 less water than conventional high-pressure sprayers. Low pressure also means low maintenance. The 2Q4CEH Head shown covers 4 rows and features a hydraulic remote control, making it ideal for nurseries.
T55 with 2Q4CEH
MODEL/GAL HP LBS CONTROLS
T45/200 35 838 electricT45/300 40 926 electricT45/400P2 45 1212 electricT50/300 55 992 electricT50/400P2 60 1212 electricT55/300 70 1109 electricT55/400P2 75 1280 electricT55/525P2M 75 1340 electric
Swivel Sprayers
CIMA’s swivel sprayers 300 and 400 gallons trailer, and have a spray head available for virtually any crop.
S50 with 2Q2C
MODEL/GAL HP LBS CONTROLS
S50/300 55 959 electricS50/400 55 959 electric
4
DISTRIBUTION HEADSDISTRIBUTION HEADS
The spray-heads can be used on:
• Almond Trees• Apple• Apricot• Cherry• Hop Plant• Jujube Trees• Nectarine• Peach• Pear Trees• Pomegranate• Canopy Vineyard• Kiwi• Pergola Vineyard• Plum
CIMA Heads 4x4
5x5
6 Duals
2Q4C
Fishtail/Hops Heads
CIMA offers a wide range of interchangeable spray heads designed to deliver spray droplets that are optimum for coverage. Using different size Venturi to change air volume and the adjustable orientation feature directs air flow to targeted canopy that ensures excellent penetration and treatment. The combination of targeted spray and anti-drip device there is minimal over spray, waste of chemical and is friendlier to the environment.
4x4 for all sprayers
5x5 for all sprayers
2Q4C for P/S/T45, P/S/T50, & P/S/T55
6 Duals for P42, P/S/T45
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
2Q2Q
2Q2Q for 45’s, 50’s, & 55’s
2Q4CEH
2Q4CEH for P/S/T45, P/S/T50, & P/S/T55
CIMA’s Tower Spray HeadsCIMA’s Tower spray heads are designed for a targeted approach for disease and pest control, even with tall canopies. Spray nozzles can be adjusted manually or by remote control for various height crops or a sloped terrain.
Row Cannon Low or High Mount
TOWER SPRAY HEADSTOWER SPRAY HEADS
5
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-04546
CIMA’s Multi-Row Spray HeadsCIMA manufactures several custom on target multi row delivery heads for your needs. Simply match up your specific growing conditions to the configurations below, you will have an ideal sprayer to complement your needs.
Configurations Chart A B C D E E
Optional 4 NozzleHand instead of upper cannon
Five way electric over hydraulic controls
MULTI-ROW SPRAY HEADSMULTI-ROW SPRAY HEADS
Rob 3 Wrap-A-Round
Evolution of a “Wrap-A-Round” boom. Coming to your farm.• Mounted on a S55 3-point hitch CIMA with 300 or
400-gallon trailing tank.• The center turret mount with transformer like arms
will quickly fold and unfold with one movementto spray 3 complete rows with one pass. Up to 9 ft.wide rows.
• Each side will be treated with spray from CIMAtargeted atomizer heads.
7Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
MULTI-ROW SPRAY HEADSMULTI-ROW SPRAY HEADS WRAP-A-ROUND SPRAYERWRAP-A-ROUND SPRAYER
This head is for the S55 300 Gal & 400 Gal.
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-04548
SMALL ACRE SPRAYERSSMALL ACRE SPRAYERS
BDi Small Acre Sprayer
BDi’s P35 is just the right size for the small acres, or start up growers. The Cifarelli blower produces 200 MPH air flow, with droplets range from 100-150 microns in size. Perfect for disease and insect control at low GPA rates. The CIMA fan-tail spray head is ideal for close dense crops, with an adjustable up/down to best target different crop heights. The 30-gallon tank is just the right size to cover about one acre per fill up. The 12V pump supplies liquid to the spray head and agitates the mixture in the tank. On/off controls are mounted near the operator. The frame is multi-use, with 3PT to attach to a small tractor, a base/skid can sit on the back of a gator or golf cart, or the optional wheel kit bolts on.
2 step calibration made simple, with Teejet quick-change orifice, and pressure regulator for fine tune adjustments.
WHEEL KIT
P30 Shown with wheel kit.“This mini-sprayer offers features of full-size sprayers, with the flexibility to mount on many small vehicles.”
Bolts-on to the standard frame to pull-behind tractors or ATVs
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 9
Cifarelli backpack sprayers have a 5HP engine and a large 4 1/2 gallon tank. With a 40’ vertical and over 50’ horizontal sprays are unparalleled. Standard equipment includes lumbar pad, optional dusting attachment, and louvered tip for veggie crops.
Additional Options• Booster Pump• Filling Pump• Accessory for powders andgranular materials
• Kit 3 louvered ends for veggiecrops
• ULV system - With thisaccessory it is possible toperform ultra-low volumetreatments(with droplets of reducedsize) and accuratelydispense the product. 70 Mu, fortunneland greenhouses
BACKPACKS & HELMETS BACKPACKS & HELMETS SMALL ACRE SPRAYERSSMALL ACRE SPRAYERS
CIFARELLI’S Backpack Sprayers
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045410
BDi PH 60 Weed Sprayer
The PH 60 is a versatile 12 volt, 3 point hitch, herbicide sprayer, rubber domes, with adjustable spray booms with tilt control as well as a separate hose line and wand nozzle for spot spraying. This unit will adapt to the area in which it is utilized, with the easy access controls this makes it easy and convenient to use for the operator.
Features• 60 Gallon Capacity• 5 GPM / 60 PSI 12V Pump• Jet agitation• Adjustable spray boom
(In & Out) 6’ Min 8’ Max• Dual 20” rubber cones.
24” or 12” spray pattern• Anti drip nozzle holder.• Safety kickback spring
joints.• Separate hose line with
wand gun.
PH 60 WEED SPRAYERPH 60 WEED SPRAYER
BETTERBETTERMADEMADEFARMINGFARMING
ONE MACHINE AT A TIME...ONE MACHINE AT A TIME...
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
TREE DIGGERSTREE DIGGERS
HZC 25
The HZC 25 is a compact machine that can work where rows and plant spacing are very close. The turning blades allow you to dig out where other machines can’t fit. This is a great solution for high density growers. The Narrow 33” wide track with patented single action in/out to 48” and forward 14” insures balance in any condition. It will dig 2 1/2 times more tree’s in the same time as other brands. This is possible with the 3 separate pump actions, horizontal 70 degrees right and left turn and 4000 vibrations per minute blade. This combination will allow a faster approach, faster digging, and faster bag & basket time. Travel speed variable from 0 to 4 mph forward and reverse, 2 ranges are controlled on the go.
The blade change is simplified with blade support for 9 different blades from 10” to 28”.
Features• 3 Separate pump actions: approaching tree faster to place in digging position.• Vertical tip back blade lifts root ball.• Horizontal turn blade right and left. 70 Degree, aides in quicker time to bag.• Adjustable rubber tracks: Move Simultaneously for less stress or single movement in/out, and forward/back. *Patented System*• 4000 Vibrations per minute blade, for better and smoother operation, It will dig 2 1/2 times more trees same time as other brands.• Forward or reverse speed 0 to 4 mph High / low range switch. Independent turn levers.• Roll over protection (ROP) & Seat belt.
Specifications- 35 HP Kubota water cooled 4 Cylinder engine- Track adjustment (33” to 48”) In-Out- Track adjustment from center to forward 14” for better balance- Two Speed (2 mph) to (4 mph) variable- Balance weight with rear jack stand- Weight – 3,440 lbs.- Choice of 9 different size blades (from 10” to 28”).
Options- Work Lights - - Hydraulic assist to quickly change blade
11
12
TREE DIGGERSTREE DIGGERS TREE DIGGERSTREE DIGGERS
HZC 30
The HZC 30 is a tree digger which includes a series of innovations. Vertical tip back and vertical lift system for lifting the root ball out of the ground, horizontal turn of the blade/vibrator of 70 degrees right and left, and independent opening/forward track system. The Narrow 33” wide track with patented single action in/out to 51” and forward 14” insures balance in any condition. It will dig 2 1/2 times more tree’s in the same time as other brands. This is possible with the 3 separate pump actions, this will allow a faster approach, faster digging, and faster bag & basket time. Travel speed variable from 0 to 4 mph forward and reverse, 2 ranges is controlled on the go. Unlike other brands in this class the HZC 30 standard with 14” vertical lift to keep the tree more stable when lifting.
The blade change is simplified with blade support for 12 different blades from 10” to 40”.
Features• 3 Separate pump actions: approaching tree faster to place
in digging position.• Horizontal turn blade right and left. 70 Degree,
aides in quicker time to bag.• Vertical lift vibrator and blade 14” aides in
stabilizing tree and tip back.• Centralized greaser: easier for maintenance.• Adjustable rubber tracks: Move Simultaneously
for less stress or single movement in/out, andforward/back. *Patented System*
• 4000 Vibrations per minute blade, for better andsmoother operation, It will dig 2 1/2 times more trees same time as other brands.
• Forward or reverse speed 0 to 4 mph High / low range switch. Independent turn levers.• Roll over protection (ROP) & Seat belt.• Work lights front and rear.
Specifications- 35 HP Kubota water cooled 4 Cylinder engine- Track adjustment (33” to 51”) In-Out- Track adjustment from center to forward 14” for better balance- Two Speed (2 mph) to (4 mph) variable- Balance weight with rear jack stand- Weight – 4,080 lbs.- Choice of 12 different size blades (from 10” to 40”)
Options- Additional Lights- Hydraulic assist to quickly change blade
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045413
TREE DIGGERSTREE DIGGERS
HZC 40
The HZC 40 is a larger tree digger which includes a series of innovations. Standard vertical tip back system for lifting the root ball out of the ground. The Narrow 41” wide track with patented single action in/out to 60” and forward 14” insures balance in any condition. It will dig more tree’s in the same time as other brands. This is possible with the 3 separate pump actions, this will allow a faster approach, faster digging, and faster bag & basket time. Travel speed variable from 0 to 4 mph forward and reverse, 2 ranges is controlled on the go. The blade change is simplified with blade support for 12 different blades from 16” to 55”.
Features• 3 Separate pump actions: approaching tree faster to place in digging position.• Centralized greaser: easier for maintenance.• Adjustable rubber tracks: Move Simultaneously for less stress or single movement in/out, and forward/back. *Patented System*• 4000 Vibrations per minute blade, for better and smoother operation.• Forward or reverse speed 0 to 4 mph High / low range switch. Independent turn levers.• Roll over protection (ROP) & Seat belt.• Work lights front and rear.
Specifications- 50 HP Kubota water cooled 4 Cylinder engine- Track adjustment (41” to 60”) In-Out- Track adjustment from center to forward 16” for better balance- Two Speed (2 mph) to (4 mph) variable- Balance weight with rear jack stand- Weight – 5,180 lbs.- Choice of 12 different size blades (from 16” to 55”).
Options- Horizontal turn blade right and left. 70 Degree, aides in quicker time to bag (Adds 1,566 lbs.)- Crane System- Additional Work Lights
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
TREE DIGGERSTREE DIGGERS TREE DIGGER ACCESSORIESTREE DIGGER ACCESSORIES
Blades/Gyro Kart
14
Please note: these are the same model, the right one is just showing the handle extended.
Lifts all containers 2 gallon to 25 gallon
Holmac BladesHolmac blades are made from Weldox® steel, which is the standard for abrasion resistant steel. Weldox® is a tough steel for aggressive environments.
Blade Extensions*-25 cm (10”) Blade Extension (3 hole) HZC 40-25 cm (10”) Blade Extension (3 hole) HZC 30-25 cm (10”) Blade Extension (1 hole) HZC 25
*Required to extend bladeto outer end of support armand a deeper dig.
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045415
Infaco Electrocoup F3015
The ELECTROCOUP F3015 electric pruning shears will once again set new bench marks in the industry. A tool designed for pruning professionals, the F3015 has evolved from its predecessors to be a more reliable and high-quality tool, preferred by users throughout the world. High quality materials have been selected with the utmost care in developing this new model. Infaco’s extended research and development has helped achieve an even lighter and more compact body. The new tool has been designed to run on a new brushless motor technology powered by a cutting-edge Lithium-ion battery. The aluminium body (made of a special alloy used in aeronautics) holds and keeps together components in the pruning shear and is now covered by a lifetime warranty.Compact & Light: 1.74 lbs
Performances: Exceptional Power and Efficiency
High Cutting Capacity:
• 40mm / 1.57 in. Standard Kit
• 45mm / 1.77 in. Medium Kit
• 55mm / 2.17 in. Maxi Kit
Ergonomic Design
Soft and Comfortable Grip
Very Accurate Progressiveness
Trigger Control
ULTRA-COMPACT LITHIUM ION BATTERYThe Lithium-ion Cobalt battery weighs only 1.79 lbs. The storage cells of the battery have been chosen for their reliability and capacity to deliver intense current. 120Wh LITHIUM Battery Weight: 1.79 lbs. Full-day complete autonomy 9hrs* Battery with storage cells protection and management electronic system (BMS) High storage capacity lithium cells. High power and long life intelligent battery technology.
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 16
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES PRUNERS & ACCESSORIESPRUNERS & ACCESSORIESBlades
F3015 STANDARD KITTO BE USED ON WOOD UP TO 40MM / 1.57’’ - IDEAL FOR CUTTING VINES AND CAN BE ADAPTED FOR CERTAIN APPLICATIONS IN TREE PRUNING. THIS KIT HAS THE BEST RATIO BETWEEN CUTTING RATE AND POWER.Pruning shear weight 1.74 lbs.Blade opening (mm) 60 mm / 2.36”Cutting capacity (mm) 40 mm / 1.57”
F3015 MEDIUM KITTO BE USED ON WOOD UP TO 45MM / 1.77’’ - WITH THE MEDIUM KIT, INCREASE THE CUTTING CAPACITY OF YOUR TOOL WITHOUT SACRIFICING SPECIALLY DESIGNED FOR TREE LOPPING, FORESTRY WORK AND PARKS & GARDENS. WORKING SPEED. SPECIALLY DESIGNED FOR CUTTING SMALL TO MEDIUM SIZED BRANCHES IDEAL FOR USE IN ORCHARDS, PARKS, AND FORESTRY WORK.Pruning shear weight 1.89 lbs.Blade opening (mm) 70 mm / 2.76”Cutting capacity (mm) 45 mm / 1.77”
F3015 MAXI KITTO BE USED ON WOOD UP TO 55MM / 2.17’’ - Specially designed for cutting medium to large size branches Ideal for coppicing vines and transforming fruit trees.The Maxi kit will give your F3015 unrivaled cutting power and capacity.Pruning shear weight 2.79 lbs.Blade opening (mm) 100 mm / 3.94”Cutting capacity (mm) 55 mm / 2.17”
P8T120 – 47” – 2.4 lbs. P8F120 – 47” – 1.5 lbs. P8T210 – 6’ 10” – 3.3 lbs. P8F210 – 6’10” – 2.2 lbs.
SHARPEN YOUR BLADES IN RECORD TIMEThanks to its 3-pad connection, the new A48v3 electric sharpener is now with batteries of all ELECTROCOUP models F3005 – F3010 – F3015.
It allows you to save significant time on daily sharpening. Optimize your blades for a higher yield from your ELECTROCOUP with the A48V3. The sharpener can be plugged directly into the 48-volt battery to sharpen your blades making it portable and easy to carry.
A48V3 48 Volt Electric Sharpener
Extention Poles
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
A3M V2 Electrical Tying Device
The A3M V2.0 is an electrical tying device that makes vine tying easy. This machine is highly versatile for single or double Guyot or bowed vine training.
A soft steel wire is used for greater flexibility. Strong enough to hold until harvesting, it is easy to destroy after a year, at pruning time. It is available in several diameters 0.40 - 0.46 - 0.50 and 0.55 mm. Larger diameter wire results in longer life of wire against elements.
Two models are available: 12V or 48V
A3MV2 12V-NiMH battery-Battery weight with belt: 30.34 oz.-7000 tie autonomy-Wire diameter: 0.40, 0.46 and 0.50 mm
A3MV2 48V-Lithium battery-F3015 battery weight: 28.57 oz.-12,500 tie autonomy-Wire diameter: 0.40, 0.46, 0.50 and 0.55 mm-Operates with the battery for Electrocoup F3015 pruning shears
Ultra Fast Wire Roll Change Located on the tool and easy to access, the wire roll can be changed in just a few seconds.
Wire Tightening Adjustment Set the number of twists and the tie tension according to the required result.
TECHNICAL SPECIFICATIONSWeight of the tie machine alone 22.93 oz.Weight of the battery alone 28.57 oz. (F3015) Weight of the wire roll 3.53 oz.Opening diameter 30 mmWire diameters (available with the 12V version) 0,40 - 0,46 - 0,50 mmWire diameters (available with the 48V version) 0,40 - 0,46 - 0,50 - 0.55 mm Battery voltage 12v or 48vCharger Feed Voltage 230V 50Hz / 110V 60HzBattery autonomy 12,500 ties (F3015) 7,000 ties
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
17
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 18
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
POWERCOUP PW2
1 MOTOR = 6 TOOLS WITH OR WITHOUT POLE EXTENSION
Thanks to electronic recognition, the speed automatically adapts to the connected tool. This patented system is used to adjust the motor performance and thereby define the best power/speed/torque for the tool being used. The “flat” Brushless technology motor gives an output that is higher than that of a classic DC motor. It is compact, lightweight and is compatible with each tool. For tools with which there is a risk of cuts (hedge-trimmer, chain saw and reciprocal saw), it has added safety which stops the tool movement very quickly when the trigger is released.
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Versatile tool
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045419
Pneumatic Shears
Lisam pneumatic shears are produced in magnesium alloy casting to allow the operator to use these shears even at low temperatures with out any power variations. They can be fitted onto extension poles, to reach higher branches.SLY Super SLY
Sly is a professional shear to prune fruit trees, Super Sly Pneumatic shears are integrate light and easy to use. Sly pneumatic shears with extension rod, for easily height pruning can be integrated with extension rods. They are suitable for pruning citrus and olives.
SANA SLY SLY DT
Sana Sly is an unique pneumatic shear: Sly Dt, the pneumatic shears with double- it disinfects the blade after each cut. edged blades, for a clean, precise cut that To control the orchard and prevent leaves no residue on the trees and promotoes the transmission of plant diseases. healing of the branches.
4 WIN
4 Win: effective pruning shears for the vine, light, functional and comfortable for the operator.
SKY SAW
Sky Pneumatic saw attaches to extension pole via quick coupler, available with 10” or 8” narrow point bar. And weighs 2.2 lbs., requires 15 cfm.
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Narrow Tip Shown
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 20
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Extension Rods
Telescopic Extension RodFor all Lisam pneumatic tools
The telescopic extension arm is extremely practical and manoeuvrable for pneumatic shears, pneumatic saws and pneumatic combs. Quick coupling ends available.
Available in the following sizes:–AT01 MT.1.00-1.50 1.00m to 1.50m / 3.2 ft. to 4.9 ft.–AT02 MT.1.45-2.25 1.45m to 2.25m / 4.7 ft. to 7.3 ft.–AT03 MT.1.85-3.10 1.85m to 3.10m / 6 ft. to 10 ft.–AT04 MT.2.50-4.00 2.50m to 4.00m / 8.2 ft. to 13.1 ft.
Extension with Quick CouplingTo quickly switch from schears to saw
Quick release connector extensions are yet another example of how Lisam is committed to improving your productivity: the connector means that you can switch between different pneumatic pruning tools quickly and easily.
pneumatic shears pneumatic saws
Available in the following sizes:–AB/125 MT.1.25 1.25m / 4.1 ft.–AB/150 MT.1.50 1.50m / 4.9 ft.–AB/200 MT.2.00 2.00m / 6.5 ft.–AB/300 MT.3.00 3.00m / 9.8 ft.
21
Adapters for Pneumatic Tools
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
CODE ITEM
X2019 Double barb fitting 6x8 (no hose clamp required)
X2020 Double barb fitting 8x10 (no hose clamp required)
9056 Connection 30 degree extension rapid fised for saw and pruner
9064 Quick release telescopic extension adjustable angle connector for saw
9066 Telescopic screw on extension adjustable angle arm connector for shears (SLY9030)
9068 Telescopic screw on extension adjustable angle arm connector for shear (SuperSly 9037, 9038)
9045 Leather sheath for pneumatic shears
CODE ITEM 9110 M.100’ 6X8 or M. 50 8X109111 M.150’ 6X8 or M. 100 8X109112 M.200’ 6X8 or M. 150 8X10
CODE ITEM X2900 Winding 6x8 - Per MeterX2901 Winding 8x10 - Per Meter
CODE ITEM
X2001 6X8 quick coupling with spring X2002 8X10 quick coupling with spring
X2003 6X8 rotating connection with spring X2004 8X10 rotating connection with spring
X2040 6X8 quick cock with spring X2041 8X10 quick cock with spring
X2043 “Y” Splitter with spring X2044 “Y” Splitter with spring
X2053 “Y” Splitter quick coupling no spring
X2011 male X2042 female
Bulk Hoses & Reels
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Quick coupling 1/4
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
22
PRUNERS & ACCESSORIESPRUNERS & ACCESSORIESPRUNERS & ACCESSORIESPRUNERS & ACCESSORIES PRUNERS & ACCESSORIESPRUNERS & ACCESSORIES
Compressors
CODE ITEM BAR/PSI VOLUME(LPM) VOLUME (CFM) TANK LT. TANK GAL.
9106 LM 300/10 11/159 300 10.6 10 2.6
CODE ITEM BAR/PSI VOLUME(LPM) VOLUME (CFM) TANK LT. TANK GAL.
9102 LM 600/30 11/159 600 21 10/10 2.6 + 2.6
CODE ITEM # SHEAR BAR/PSI VOLUME(LPM) VOLUME (CFM) TANK LT. TANK GAL. WEIGHT KG/LBS
9250 Ecoline 510 4 11/159 510 18 20 5 94/207 9251 Ecoline 600 5 11/159 600 21 20 5 99/218 9252 Ecoline 980 9 11/159 980 34 20 5 116/255 9253 Ecoline 1500 14 11/159 1500 52 20 5 150/330
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045423
Introducing Anvil cutters technology... the next generation in shredding brush and cutting weeds
ANVIL BRUSH & WEED SHREDDERANVIL BRUSH & WEED SHREDDER
Anvil ShredderSide Discharge
Normal Work Speed 4 MPH
Anvil ShredderGreen Off Set
Anvil Shredder
Features
One machine does both, shreds light clippings and mows at 4 MPH homologous shredding. Anvils reduce brush and weeds to organic matter, PTO drive 3 point hitch swivel trailing models with trailing gauge wheels. Patterned front dual pick up feed fingers.
Optional Models Available: — Side discharge row mulching models — Large capacity trailer collections system — Offset with hydraulic in/out
— Front 3-point hitch PTO drive models for cuttings up to 6 inches
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 24
ANVIL BRUSH & WEED SHREDDERANVIL BRUSH & WEED SHREDDER
Single-purpose heavy duty single or dual arm
Features
• Direct PTO drive(no belts and not hydraulic motors)
• Anti-scalp 47 inch low clearance mower• 3 blade disc mower• Adjustable rear free pivot depth gauge wheel• Hydraulic in/out and tension control
DRAG MOWER (BETWEEN TREES/POSTS)DRAG MOWER (BETWEEN TREES/POSTS)
Optional Models Available: — Dual arm with a 20’ spread and 59” mowers — Rubber guide wheel for under guard-rail maintain — Outer throw shield for guard-rail models
25
CULTIVATORSCULTIVATORS
CM Deep Tine Cultivator
Cultivator “CM” with special supports “Stone-Jumper” of working groups equipped with anti-shock springs, the frame is width adjustable and cylinder for vertical hydraulic lifting available. The optional rear cage roller adjusts the working depth between 6” to 10”.
MODEL WIDTH HP LBS
CM7 110 43”-61” 65 925CM7 150 59”-76” 65 970CM9 150 59”-76” 80 1080CM9 200 78”-96” 80 1124CM11 190 74”-92” 95 1234CM11 250 98”-116” 95 1278
S Tine Shallow Cultivator The Vigneto spring tine “S” cultivator has a lot of action and is recommended for shallow cultivation in a nice soil. But not all “S” tine cultivators are equal. The Vigneto is standard with a dual upper spring support at the mount. The result is less breakage of the tines. Tines are standard with reversible points, sweeps are available by request.
MODEL # TINES WIDTH HP LBS
VI 80 9 31-51” 15 282VI 110 11 43-73” 20 472VI 130 15 51-91” 25 591055-201 Opt. Steel wheels055-202 Opt. Plant protector guards.
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net
CULTIVATORSCULTIVATORS MIDDLES MANAGEMENTMIDDLES MANAGEMENTFRP Tandem DiscsTandem Mounted 20” disc harrows FRP is perfect for work between rows. They are very strong machines with hydraulic or manual sidesoil leveling. Both rear sections are interchangeable with fixed spade 16-20-24 discs.
MODEL DISC WIDTH HP LBS
FRP 16D 16 71” 55 1410FRP 20D 20 87” 65 1630FRP 24D 24 102” 80 1800
ARP Ripper & Sub SoilerThe ARP is ideal for relieving compaction in nurseries. The unique wing design relieves hardpan and nicely prunes roots, and central straight spade are available.
MODEL WIDTH HP LBS
ARP 130 51” 60-80 55104280 Opt. Rear Cage Roller04281 Opt. Central Straight Spade
FRM Disc HarrowsDisc harrow model “FRM” with 24” cutting disc. supports “Stone-Jumper” of working groups equipped with antishock springs, the frame is width adjustable and cylinder for vertical hydraulic lifting available in order to reduce the overall and easier the movements. The rear roller adjusts the working depth between 3 and 6 inches. Available model with 8-10-12-16-20 discs. Open feed model available.
MODEL WIDTH HP LBS
FRM8D 45”- 59” 50-70 1180FRM10D 47”- 61” 55-75 1488FRM12D 59”- 73” 60-75 1798FRM16D 79”- 93” 75-90 1962FRM20D 98”- 112” 90-100 2337
26
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045427
CULTIVATORSCULTIVATORS
EL Inter Plant Cultivator
Tractor 3 Pt. PTO gear drive of the working tool and the hydraulic pump which in turn controls the touch bar. The counter rotating vertical tines ensure optimum cultivating while keeping the soil level and not cause hardpan. Ideal for stony conditions and can handle tall weeds.
Hydraulic tilt standard. Requires 20” between vines, trees, posts, etc. and 12-14” below first wire. Standard with manual retracting override; hydraulicand electro-hydraulic retracting override are optional.
MODEL WORK WIDTH ROW WIDTH HP
EL 090 6”,13”,20”,26” 48-80” 30EL 115 6”,13”,20”,26” 60-98” 30EL 140 6”,13”,20”,26” 80-118” 30EL 170 6”,13”,20”,26”- or 39” 98”-150” 30EL 200 6”,13”,20”,26”- or 39” 118-178” 40EL 225 6”,13”,20”,26”- or 39” 138-240” 4018030 Opt. Electrohydraulic Emergency Control18020 Opt. Hydraulic Emergency Control with lever
EL 140
Optional Wheel KitEL-70EL-90EL-115EL-140EL-170 Std.
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 28
DIGGER & WIGGLE HOEDIGGER & WIGGLE HOEBRMBush cutter equipment with cutting bar for tree prunings up to 1 1/4” diameter. The new versatile frame (push and pull) performs a perfect cut on both tractor’s sides.
Additional Option
• Electro-hydraulic controls withproportional joystick 4+1 for tractorswith cabin
• Auto Leveling both vertical & horizontal.
(Only 150 and 200 model)
BREThe hedge trimmer ranges increases with the model BRE for miniloader and BRG for lawn mower. Booth machines use a joystick control very precise and easy to use.
TRIMMERSTRIMMERS
MODEL A B C D E F G
BRM 120 39” 55” 67” 102” 161” -- -- BRM 150 33” 59” 94” 150” 236” 94” 75” BRM 200 33” 59” 94” 150” 236” 94” 75”
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-0454
Deep Spade Tillage
Spaders are the preferred tool for initial deep tillage and cultivation while doing the least soil structure damage. The working motion does not beat or mix soil layers and will fracture the plow pan. Cover crop is pushed downwards throughout the soil profile and the soil is broken by being forced backwards against raked tailgate. Can be used in wet soil conditions, backwards spade motion pushes the tractor forward preventing any tractor problem in wet soil.
MODEL CM/INC. HP KW N. KG/LBSmin/max
M80-4 80/32 15/35 11/26 4 245/540M90-4 90/35 15/35 11/26 4 250/550M100-4 100/39 15/35 11/26 4 255/561M120-6 120/47 18/35 13/26 6 315/693M130-6 130/51 20/35 14/26 6 320/704M145-6 145/57 25/35 18/26 6 330/726
MODEL CM/INC. HP KW N. KG/LBSmin/max
J80-4 80/32 20/45 14/33 4 335/739J90-4 90/35 20/45 14/33 4 340/750J100-4 100/39 20/45 14/33 4 345/761J110-4 110/43 22/45 16/33 4 355/783J120-6 120/47 25/45 18/33 6 430/948J130-6 130/51 25/45 18/33 6 440/970J145-6 145/57 28/45 20/33 6 450/992J160-6 160/63 30/45 23/33 6 460/1014J160-8 160/63 32/45 23/33 8 520/1147J180-8 180/71 35/45 26/33 8 540/1191
MODEL CM/INC. HP KW N. KG/LBSmin/max
W90-4 90 25/75 18/55 4 380W100-4 100 25/75 18/55 4 390W110-4 110 25/75 18/55 4 400W130-6 130 35/75 26/55 6 490W145-6 145 35/75 26/55 6 500W160-6 160 35/75 26/55 6 510W180-8 180 40/75 29/55 8 620W200-8 200 40/75 29/55 8 640
120-35120-35
120-45120-45
120-75120-75
10” DEEP
10” DEEP
10” DEEP
29
SPADERSSPADERS
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 30
MODEL CM/INC. HP KW N. KG/LBSmin/max
M80-4 80/32 15/35 11/26 4 245/540M90-4 90/35 15/35 11/26 4 250/550M100-4 100/39 15/35 11/26 4 255/561M120-6 120/47 18/35 13/26 6 315/693M130-6 130/51 20/35 14/26 6 320/704M145-6 145/57 25/35 18/26 6 330/726
MODEL CM/INC. HP KW N. KG/LBSmin/max
J80-4 80/32 20/45 14/33 4 335/739J90-4 90/35 20/45 14/33 4 340/750J100-4 100/39 20/45 14/33 4 345/761J110-4 110/43 22/45 16/33 4 355/783J120-6 120/47 25/45 18/33 6 430/948J130-6 130/51 25/45 18/33 6 440/970J145-6 145/57 28/45 20/33 6 450/992J160-6 160/63 30/45 23/33 6 460/1014J160-8 160/63 32/45 23/33 8 520/1147J180-8 180/71 35/45 26/33 8 540/1191
MODEL CM/INC. HP KW N. KG/LBSmin/max
W90-4 90 25/75 18/55 4 380W100-4 100 25/75 18/55 4 390W110-4 110 25/75 18/55 4 400W130-6 130 35/75 26/55 6 490W145-6 145 35/75 26/55 6 500W160-6 160 35/75 26/55 6 510W180-8 180 40/75 29/55 8 620W200-8 200 40/75 29/55 8 640
POWER HARROWSPOWER HARROWS
Power Harrows
The POWER HARROWS are the preferred tillage tool to work the soil shallow or deeply without turning layers of soil -- topsoil stays on top. The machine can also be set for shallow cultivation. Rotor heads are inter-linked and gear driven for long life and a consistent work quality. The vertical tines counter rotate and reduce clods to a small size. An optional rear mesh roller controls depth and leaves a fine seedbed ready for seeding. Used in conjunction with spaders these tools can do all your mechanical tillage and soil cultivation in a manner that best preserves your soil life and structure. Maintenance is quick and simple. Surface rocks are less of a problem for a power harrow than they are for a tiller.
MODEL DEPTH WIDTH HP LBS
Alfa 110 8 3/4” 43” 20 495 Alfa 130 8 3/4” 51” 25 559 Alfa 150 8 3/4” 4.9’ 30 627 Sirio 150 10 1/4” 4.9’ 30 781 Sirio 170 10 1/4” 5.9’ 35 856 Sirio 190 10 1/4” 6.3’ 40 924 Sirio 210 10 1/4” 6.9’ 45 999 Beta 205 11 3/4” 6.8’ 60 1408 Beta 230 11 3/4” 7.6’ 70 1496 Beta 250 11 3/4” 8.3’ 80 1584 Beta 300 11 3/4” 10’ 90 1760 Omega 250 11 3/4” 8.3’ 80 1727 Omega 300 11 3/4” 10’ 90 1914 Gamma 300 11 3/4” 10’ 100 2888 Gamma 350 11 3/4” 11.6’ 120 3175 Gamma 400 11 3/4” 13.3’ 140 3461
SPADERSSPADERS
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045431
STONE AND SOD BURIERSSTONE AND SOD BURIERS
Stone and Sod Burier
The SA and SB tillage machines are designed for working in stony soils and for preparing sowed middles for replanting. Basically, this tillage machine does primary secondary and finish tillage in one pass. This is possible by the reverse rotation of a standard tiller that picks up stones and/or sod clumps and deposits them at the bottom of the furrow while leaving the fine soil on top as the mesh cage roller firms the finish seed bed. To renovate vineyard middles, choose the optional seed box to complete the final task of replanting the cover crop before the mesh caged roller firms the new seed bed. Your row middles will have a finished look and the level rows will make it easier for traveling during regular operations.
MODEL DEPTH WIDTH HP LBS
SA100R 5” 39” 20-45 829 SA120R 5” 46” 30-45 900SA135R 5” 52” 35-45 983SB120R 7” 47” 30-75 1177SB140R 7” 55” 35-75 1283SB165R 7” 64” 40-75 1388SB185R 7” 72” 50-75 1494SB205R 7” 80” 60-75 1599Opt SEED BOX
BDi Machinery Sales, Inc. - 52 Race Street, Macungie PA 18062 - Phone: 1-800-808-045432
SHREDDERS/MOWERSSHREDDERS/MOWERS
TRF & TRF-A Mower/Shredder
The TRF is suitable for mid-size pruning up to 2 inches of pruning’s, and is ideal for small jobs. The TRF-A features an adjustable rear gate and roller, and comes standard with hammers. Optional Y-flails, manual or hydraulic side shifting is available.
MODEL WIDTH HP LBS
TRF085 33” 20 353TRF100 39” 20 462TRF115 45” 24 529TRF130 51” 28 617TRF150 59” 32 661TRF165 65” 36 750TRF180 71” 40 838-A Opt Openable rear gate for discharge.
TRF165
TRF-A
Nursery Edition - www.bdimachinery.net - buydirect@bdimachinery.net 33
SHREDDERS/MOWERSSHREDDERS/MOWERS SHREDDERS/MOWERSSHREDDERS/MOWERS
TRL & TRL-B
The TRL’s hammer action shredder is ideal for grass and pruned branches with a diameter of up to 3 1/4”. The TRL-B low profile is ideal for reaching under the cordon in vineyards. Both models come standard with rakes. Optional hydraulic side shift is available on the TRL model only.
MODEL WIDTH HP LBS
TRL125* 49” 35 992 TRL150* 59” 40 1080 TRL175* 69” 45 1168 TRL200* 79” 50 1256 TRL225* 89” 55 1388TRL-B125 49” 35 881TRL-B150 59” 40 970TRL-B175 69” 45 1058TRL-B200 79” 50 1146*Opt Hydraulic Side Shift
TRL175
TRL-B (LOW PROFILE)
MODEL WIDTH HP LBS
TRF085 33” 20 353TRF100 39” 20 462TRF115 45” 24 529TRF130 51” 28 617TRF150 59” 32 661TRF165 65” 36 750TRF180 71” 40 838-A Opt Openable rear gate for discharge.
BDi Machinery Sales, Inc. | 52 Race Street, Macungie PA 18062 | Phone: 1-800-808-0454
BETTERBETTERMADEMADEFARMINGFARMING
ONE MACHINE AT A TIME...ONE MACHINE AT A TIME...