Post on 29-Jan-2021
Less Info
Countries: CANADA, TAIWAN, UNITED STATES,
GUAM, KOREA, SOUTH KOREA
Document
ID: IK1201150
Availability: ISIS, FleetISIS Revision: 2
Major System: ENGINES Created: 6/24/2014
Current
Language: English
Last
Modified: 6/17/2015
Other
Languages: NONE Author:
Josh
Bowman
Viewed: 871
Hide Details Coding Information
Copy Link Copy Relative Link Bookmark Add to Favorites Print Provide Feedback Helpful Not Helpful
View My Bookmarks 2 0
Title : Maxxforce 15L Injector Sleeve Replacement
Applies To : 2011 Maxxforce 15L
CHANGE LOG:
2015/6/17 - Updated parts table and steps to use Loctite 515 instead of Loctite 620 compound
2014/10/28 - Updated format
2014/08/11 - Updated SRT information
2014/08/04 - Launch to field
DESCRIPTION:
This article provides the procedure for injector sleeve replacement on the Maxxforce 15L engine. If diagnosing one or more of the
symptoms listed below and you have determined that the injector sleeve is the root cause, follow the repair procedure below.
SYMPTOMS:
- Coolant leak to fuel
Fuel in coolant
Fuel in lube oil
- Compression to fuel
SPECIAL TOOLS:
Tool Description Tool Number
Maxxforce 15L Tool Kit - TL2900007 ZTSE5028
Injector Sleeve Kit ZTSE6095
Fuel Injector Kit ZTSE6102
SERVICE PARTS INFORMATION:
Kit Description Part Number Quantity Required Notes
Page 1 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
To prevent damage to the vehicle or engine, read all safety instructions in the Safety information section
of the Service and Diagnostic Manual for the application that is being serviced
Kit, Injector Sleeve 7092980C91 6 Remove Loctite 620 in kit - use Loctite 515
Kit, Injector Seal Kit 3014430C91 6
Tube Assy Rail to Injector 3007916C2 1
Tube Assy Rail to Injector 3007915C2 1
Tube Assy Rail to Injector 3007914C2 1
Tube Assy Rail to Injector 3007913C2 1
Tube Assy Rail to Injector 3007912C2 1
Tube Assy Rail to Injector 3007911C2 1
Loctite 515 PTX51531 1Replaces Loctite 620 that comes in Injector
Sleeve Kit
REPAIR PROCEDURE
To prevent personal injury or death, read all safety instructions in the Safety Information section of the
Service and Diagnostic Manuals for the application that is being serviced
REMOVAL:
1. Remove the rail to injector tube assembly, valve brake actuator assembly, rocker arm assembly and lost motion
pedestals, following the removal procedures in the EGES-510 Engine Service Manual. Discard the rail to injector tube assembly.
2. Remove the highpressure connector retaining nut
3. Remove high pressure connector from cylinder head
4. Remove the 3/8 -16 x 4 hex bolt, 9.8 x 15.85 x 37.6 spacer, and injector clamp for affected cylinders
Page 2 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 1: Installation of threaded legs into lost motion pedestal bolt holes
Item 1 - ZTSE6095-4 Threaded Legs
5. Install the two threaded legs (Figure 1, Item 1)--with wrench flats up--into lost motion pedestal bolt holes. Hand tighten
threaded legs.
Page 3 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 2: Installation of ZTSE6102-1 jaw puller assembly on fuel injector
Item 1 - ZTSE6102-1 Jaw Puller Assembly
Item 2 - Fuel Injector
6. Install the jaw puller assembly onto the fuel injector (Figure 2, Item 1).
Page 4 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 3: Installing ZTSE6095-3 threaded leg into injector hold-down bolt hole
Item 1 - ZTSE6095-3 Threaded leg
Item 2 - ZTSE6102-1 Jaw Puller Assembly Installed on fuel injector
7. Install ZTSE6095-3 threaded leg into the injector hold-down bolt hole. Hand tighten threaded leg.
Page 5 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 4: Installing Tee Plate
Item 1 - ZTSE6095-1 Tee plate
Item 2 - Threaded legs (ZTSE6095-3, ZTSE6095-4)
Item 3 - ZTSE6102-1 Jaw puller assembly
8. Install Tee plate ZTSE6095-1 over threaded legs and jaw puller assembly
9. Install three nuts on threaded legs and hand tighten
Page 6 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 5: Installed tee plate
Item 1 - Hand tightened nuts on threaded legs
Item 2 - 5/8 washer and 5/8-18 nut on ZTSE6102-1 jaw puller assembly
10. Install 5/8 washer and 5/8-18 nut onto jaw puller assembly ZTSE6102-1 and turn clockwise until injector is out.
11. Remove three nuts from threaded legs
Page 7 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 6: Removed Injector
Item 1 - ZTSE6102-1 Jaw puller assembly
Item 2 - Fuel injector
12. Lift Tee plate vertically and then remove injector assembly from jaw puller assembly
13. Place injector into fuel injector rack holder ZTSE4299B
Continue with procedure to remove fuel injector sleeve
14. Thread the sleeve puller (ZTSE6095-2) into the fuel injector sleeve.
15. Place the Tee plate (ZTSE6095-1) over the sleeve puller and threaded legs. Install the three nuts on threaded legs and hand
tighten.
16. Install the washer and large hex flange nut onto the sleeve puller. Turn the large hex flange nut clockwise until the fuel
injector sleeve is removed from cylinder head.
Page 8 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 7: Removal of injector sleeve
Item 1 - ZTSE6095-2 sleeve puller
Item 2 - Injector sleeve
Item 3 - ZTSE6095-1 Tee plate
Item 4 - Hand tightened nuts on threaded legs
17. Remove three nuts from the threaded legs. Lift the Tee plate (ZTSE6095-1) from sleeve puller and discard.
Page 9 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 8: Removed injector sleeve
Item 1 - ZTSE6095-1 Tee plate
Item 2 - ZTSE6095-2 sleeve puller
Item 3 - Injector sleeve
Item 4 - Injector sleeve O-Rings
INSTALLATION
1. Lubricate the upper O-rings on the new fuel injector sleeve with P-80.
2. Apply Loctite compound 515 to the bottom O-ring
3. Align the hole on side of fuel injector sleeve with hole in cylinder head for high-pressure connector and then place new fuel
injector sleeve into injector port in cylinder head.
4. Place injector sleeve installer assembly (ZTSE6095-5) into fuel injector sleeve. Ensure the spring pin on bottom of the sleeve
installer assembly aligns with groove on fuel injector sleeve. Place sleeve and installer in injector sleeve bore
Page 10 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 9: Spring pin alignment
Item 1 - Spring pin
Item 2 - Injector sleeve groove
5. If not already done, install two threaded legs ZTSE60954 into bolt holes for lost motion pedestal assembly, and one threaded
leg ZTSE6095- 3 into bolt hole for fuel injector clamp bolt.
6. Install Tee plate ZTSE6101-1 onto threaded legs and secure with three nuts hand tight.
There is a "U" shaped cutout on threaded leg ZTSE6095-3 that must be aligned with cup driver
7. Thread forcing screw assembly ZTSE6101-3 into Tee plate ZTSE6101-1 and turn clockwise until injector cup is completely
installed. Injector cup is completely installed when you cannot turn driving bolt anymore. (approx. 24.9 lbft)
8. Unscrew forcing screw assembly ZTSE61013 until it is not in contact with driver and remove the three nuts from the threaded
legs. Lift the Tee plate vertically and remove.
9. Remove threaded legs from cylinder head
10. Remove injector sleeve installer assembly (ZTSE6095-5).
Page 11 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
To prevent engine damage, align injector correctly with cylinder head so injector tube inlet port
aligns with pressure pipe holes in cylinder head; do not twist injector when inserting injector into
cylinder head
Figure 10: Fuel Injector
Item 1 Injector
Item 2 - O-ring
Item 3 - Combustion gasket
11. Remove and discard O-ring from each fuel injector
12. Install a new O-ring on each fuel injector. Lubricate O-ring with clean engine oil
13. Install a new combustion gasket on each fuel injector
14. Remove disposable air and fuel caps from cylinder head injector bore
15. Install injector using injector installer ZTSE4777. Push firmly until injector is seated all the way into injector sleeve.
16. Install injector clamp(s), 9.8 x 15.85 x 37.6 spacer(s) and 3/8 16 x 4 hex bolt(s). Tighten 3/8 16 x 4 hex bolt(s) hand tight.
Page 12 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Figure 11: High-pressure connector
Item 1 - High-pressure connector retaining nut (6)
Item 2 - High-pressure connector body (6)
Item 3 - 13 x 3 O-ring (6)
17. Lubricate the 13.5 x 3 O-rings on the high pressure connector bodies with clean engine oil.
18. Install six new high-press connector body and 13.5 x 3 O-ring assemblies.
19. Lubricate the high-pressure connector retaining nut threads with clean engine oil
20. Install high-pressure connector retaining nut(s). Tighten high-pressure connector retaining nut(s) to 55 N·m (40 lbf ·ft)and
then loosen completely. Tighten retaining nut(s) again 10 N·m (88 lbf·in).
21. Tighten 3/8-16 x 4 injector clamp hex bolts to 25 N·m (18 lbf·ft) + 90°.
22. Tighten highpressure connector retaining nuts to 20 N·m (15 lbf·ft) + 25°.
23. Re-install lost motion pedestal(s), rocker arm assembly(s) and valve brake actuator(s) following the service procedures in the
EGES510 service manual
WARRANTY INFORMATION:
Warranty Claim Coding:
Group: 12000 - Engine
Noun: 563 - Injector Unit (Electrical)
Page 13 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...
Hide Details Feedback Information
Viewed: 870
Helpful: 2
Not Helpful: 0
Staff
ID
Client
IDComments
Created
Date
DY46592
You received the following feedback From: dy46592 - Drew Harrison Email Address: drewh@gsindustrial.com Job Classification: SE008,
Service Technician Dealer: G & S INDUSTRIAL, INC. Feedback: could you guys include a part number for the high pressure connectors in
the parts break down?
6/29/2015
11:03:21 AM
Copyright © 2015 Navistar, Inc.
STANDARD REPAIR TIMES:
Hours Code Model Engine Qualifier 1
1.7FA12-7563O-2
Injector Sleeves, Replace 9900i |MAXXFORCE 15| Fuel Injector, Replace
Add On
1.7R12-7563O-2
Injector Sleeves, Replace ProStar |MAXXFORCE 15| Fuel Injector, Replace
Add On
1.7T12-7563O-2
Injector Sleeves, Replace 5000 |MAXXFORCE 15| Fuel Injector, Replace
Add On
1.7TC12-7563O-2
Injector Sleeves, Replace CAT CT660 |MAXXFORCE 15| Fuel Injector, Replace
Add On
OTHER RESOURCES:
EPA 2010 MaxxForce 11, 13, N13, and 15 Service Resource Center
MaxxForce® 15L Engine Service Manual (Supersedes EGES-510)
2011 MaxxForce® 15 Engine Diagnostic/Troubleshooting Manual (Revision 1)
Page 14 of 14IK1201150 Maxxforce 15L Injector Sleeve Replacement
7/1/2015https://evalue.internationaldelivers.com/service_kb/DocTool/ArticleViewer.aspx?ControlID...