Post on 24-Dec-2015
M. Zaharna Clin. Chem. 2009
What is Quality Control?What is Quality Control?
Quality Control in the clinical laboratory is a system designed to increase the probability that each result reported by the laboratory is valid and can be used with confidence by the physician making a diagnostic or therapeutic decision.
M. Zaharna Clin. Chem. 2009
Quality Control ProgramsQuality Control ProgramsThe goal of a well-defined QC system is to detect
immediate errors in an analytical run while minimizing the number of false rejections.
The simplest type of QC procedure uses one rule to reject the analysis based on QC results falling outside of a range such as the 95% range.
These facts are based on probability that the correct decision was made 95% of the time when results that fall within this range are accepted.
When testing is qualitative—that is, positive or negative—a simple one-rule policy is acceptable.
M. Zaharna Clin. Chem. 2009
Control Of The Analytical Control Of The Analytical Quality Using Stable Control Quality Using Stable Control MaterialsMaterialsThe performance of analytical methods can
be monitored by analyzing specimens whose concentrations are known and then by comparing the observed values with known values.
The known values are usually represented by an interval of acceptable values, or upper and lower limits for control (control limits)
When the observed values fall within the control limits – analysis is working properly
When the observed value fall outside the control limits the analyst should be alerted to the possibility of problems in the analysis.
M. Zaharna Clin. Chem. 2009
Control Of The Analytical Control Of The Analytical Quality Using Stable Control Quality Using Stable Control MaterialsMaterialsQA includes analyzing known samples
called quality control (QC) samples along with unknown (patient) samples to test for analytical problems.
When QC samples do not produce accurate and precise results, it can be assumed that any patient results obtained at the same time are also erroneous.
Following a set of guidelines for acceptance or rejection of patient results based on the QC results helps to assure reliability of the analysis.
M. Zaharna Clin. Chem. 2009
Standards and ControlsStandards and ControlsStandard
A substance that has an exact known value and that, when accurately measured, can produce a solution of an exact concentration
Not usually used on a daily basis Used to calibrate new instruments,
recalibrate instruments after repair, at manufacturer’s recommended intervals, or if a method is out of control
M. Zaharna Clin. Chem. 2009
ControlControlA solution that contains the same
constituents as those being analyzed in the patient sample
Most are commercially produced from pooled sera
The manufacturer has analyzed each lot of serum for a variety of test components and the expected range of assay values for each component is provided to the laboratory when shipped
M. Zaharna Clin. Chem. 2009
Control Control Controls are analyzed with each
patient test or batch of tests and the results are compared with the manufacturer’s range of values
For most tests, a “normal” control and an “abnormal” control are analyzed with each patient test or batch of tests
Results are plotted on a QC record called a Levey-Jennings Chart
M. Zaharna Clin. Chem. 2009
Quality control (QC) Quality control (QC) proceduresprocedures
Quality control (QC) procedures function by detecting analytical errors; ◦ideally any error large enough to
invalidate the medical usefulness of laboratory results should be detected.
The measurement of QC samples will detect problems of precision and accuracy over time.
Interpretation of control results is based on using specific rules for acceptance and rejection of QC results, documenting results and decisions, and having a process for resolving problems that result in rejection of results.
The mean (X) is the sum of the control observations (x1, x2, ... xi) divided by the number (n) of observations:
Practice calculating the mean of the
following five results: 45, 44, 45, 48, 39(n 5). (45 44 45 48 39)/5
221/5 44.2The standard deviation (SD or s) is the
measure of the dispersion of a group of values around the mean. It is derived from the curve of normal distribution. It is used to assess precision.
Practice calculating the SD of the following results: 45, 44, 45, 48, 39 (n 5).
SD (s) = 3.3
Statistical CalculationsStatistical Calculations
M. Zaharna Clin. Chem. 2009
Standard Deviation (SD)Standard Deviation (SD)It is the commonly used measure
of dispersionGives a measurement of
dispersion around the meanCalculation:
◦X ± 1SD includes 68% observations◦X ± 2SD includes 95% observations◦The higher the SD, the more the
observation varies (deviates) from the mean.
M. Zaharna Clin. Chem. 2009
Percentage Coefficient of Percentage Coefficient of Variation (%CV) Variation (%CV)
Measures level of imprecisionAssess the reliability of a given
method based on preset values
% CV =
S dard D evia tion
M ean
tan1 0 0
M. Zaharna Clin. Chem. 2009
Gaussian Probability Gaussian Probability DistributionDistribution
It is very important in statistics
When the distribution of values around the mean are plotted graphically and are symmetrical this is referred to as a Gaussian curve.
Statistical procedures are based on Gaussian probability distribution.
M. Zaharna Clin. Chem. 2009
68-95-99.7 Rule68-95-99.7 RuleFor any normal curve with
mean mu and standard deviation sigma:
68 percent of the observations fall within one standard deviation sigma of the mean.
95 percent of observation fall within 2 standard deviations.
99.7 percent of observations fall within 3 standard deviations of the mean.
How Are These Values How Are These Values Used?Used?Mean and SD are calculations that
assess the accuracy and precision of the analysis statistically.
Errors of accuracy may be assessed by examining changes in the measured concentration of the control over time and comparing these concentration values to mean and SD ranges of the control.
By contrast, an imprecision problem will be demonstrated by an increase in the SD and %CV of results of the control concentration over time.
Control charts are simple graphical displays in which the observed values are plotted versus the time when the observations are made.
The control limits are calculated from the mean (x) and standard deviations (s)
General Principles Of Control Charts
The most commonly used charts indicate day or run number on the X-axis and observed QC concentration, indicating mean, and SD ranges on the Y-axis
One example of a QC chart is the Levey-Jennings control chart.
By plotting the daily QC results, one can visualize the deviation of the results from the mean, typically noting when the results are greater than 2 SD from the mean on a daily basis.
General Principles Of Control Charts
Control RulesControl RulesThe criteria used to determine
acceptability of each control measurement are termed control rules, or QC rules.
Westgard defined QC rules based on the earlier work of Shewhart, Levey, and Jennings.
Use of multiple control rules (commonly referred to as Westgard rules) can improve the performance of the control system.
M. Zaharna Clin. Chem. 2009
Control RulesControl RulesIndividual rules have different
capabilities for detecting different types of analytical error.
A control rule or control decision is used to judge whether analysis is performing well.
Ranges can be tighter if clinical requirements are more demanding, but the SD limit should not be set so narrow that excessive time and resources are wasted checking false rejections.
Errors in Laboratory TestingErrors in Laboratory Testing
Random or Systematic Random Errors – cannot be absolutely
identified (Ex. Differences in techniques between workers, specimen characteristics, etc.)
Systematic Errors – variation that may make results consistently higher or lower than the mean value for a control (Ex. Trouble with the instrument, deteriorated reagents, etc.)
QC can be achieved through:
Internal Quality Control (IQC)External Quality Assessment
(EQA)
Types of Quality ControlTypes of Quality Control
M. Zaharna Clin. Chem. 2009
Internal Quality Control Internal Quality Control Program Program
• An internal quality control program depend on the use of:
• internal quality control (IQC) specimens,
• LJ Control Charts,
• and the use of statistical methods for interpretation.
Impact of Internal Quality Impact of Internal Quality ControlControlContinuous detection and rectification
of the Analytical Process.◦Reagent-Equipment-Personnel-Specimen◦Ensure the degree of both precision &
accuracy of your results◦Assure the quality and clinical applicability
of your laboratory reports◦Generate objective evidence of your
analytical performance.
External Quality Assessment External Quality Assessment (EQA)(EQA)Inter laboratoryComplimentary to IQCMaintain the long-term
accuracy of the analytical process.
Impact of External Quality Impact of External Quality AssessmentAssessmentContinuous quality improvementIndependent laboratory auditObjective evidence of a laboratory
analytical performanceAssess the results which the
laboratory deliversEncourages the search for the root
cause of unacceptable performance.