Post on 10-Jul-2022
JOLLY TA N K c o n c e a l e d c i s t e r n110 mm
or more
L (mm) X (mm)
200 400240 390300 360350 340400 300440 180
a
a
H I J
Ø38/46mm
Ø14/38mm
K
Fit the lid into place, taking care not to twist, kink or trap the cable.
Connect the fl exible fl ush pipe to the pan and the pan connector (not supplied with the cistern) to the waste outlet. Jollyfl ex is recommanded.
Position the control buttonon the right: for position see diagram and check against the measurements in box below.
Click the cable onto the pre-assembled button and clip the top fascia onto the unit. Fix the pan to the fl oor and seal with silicone as required. See trouble shooter in case of problem.
3 litre adjustment
6 litre adjustment
Test the complete cistern when installation is over
www.wirquin.comHELP
09/0
8 -
2124
44
340 mm
380
mm
130
mm
x1
Dual fl ush push button in chromed fi nishref: 19008101
Black cable for MW2 mechanismref: 10717443
Overfl ow washer for WIRQUIN fl ushing mechanismref: M25
TOPY fl oat valveref: 16300501
TOPY diaphragm washerref: 19066001
1
2
B CA
D
0
0
+45 mm MINI
+87 mm MAXI-69 mm MAXI-27 mm MINI
+21 mm MINI
+63 mm MAXI
40 mm mini
F
G
E
Unscrew the nut of the Topy inlet valve. Rotate the head of the inlet valve and screw the nut back on.
Fix the Topy inlet valve onto the isolation valve.
NOTE: Turn the TOPY fl oat to the right if connection is on the left, or to the left if connection is on the right.
1
1
2
2
1
12
Screw the 2 cistern wall supports to the back of the unit. NOTE: 3 options of positioning the brackets on the unit or wall.
WARNING: The positioning of the cistern must be 40mm minimum from the underside of the furniture or worktop. Horizontal adjustment of the cistern is possible after installation on the brackets.
Connect the fl ush pipe.NOTE: it is possible to connect to the cistern without the vertical tube.Also it is possible to connect to the cistern with use of the vertical section of the fl ushpipe (if installation space is tight).
Take off the sticky protection paper from the foam pad.Position the foam pad on the back of the cistern (see picture above)
NOTE: If the bottom part of the cistern is on a wall, use two foam pads.
12
x1 x1 x1 x1
x1
x1
x1
x1
x1
x1
x1
x2 x2
x1
x2
x2
x1
1
2
B CA
D
0
0
+45 mm MINI
+87 mm MAXI-69 mm MAXI-27 mm MINI
+21 mm MINI
+63 mm MAXI
40 mm mini
F
G
E
Unscrew the nut of the Topy inlet valve. Rotate the head of the inlet valve and screw the nut back on.
Fix the Topy inlet valve onto the isolation valve.
NOTE: Turn the TOPY fl oat to the right if connection is on the left, or to the left if connection is on the right.
1
1
2
2
1
12
Screw the 2 cistern wall supports to the back of the unit. NOTE: 3 options of positioning the brackets on the unit or wall.
WARNING: The positioning of the cistern must be 40mm minimum from the underside of the furniture or worktop. Horizontal adjustment of the cistern is possible after installation on the brackets.
Connect the fl ush pipe.NOTE: it is possible to connect to the cistern without the vertical tube.Also it is possible to connect to the cistern with use of the vertical section of the fl ushpipe (if installation space is tight).
Take off the sticky protection paper from the foam pad.Position the foam pad on the back of the cistern (see picture above)
NOTE: If the bottom part of the cistern is on a wall, use two foam pads.
12
x1 x1 x1 x1
x1
x1
x1
x1
x1
x1
x1
x2 x2
x1
x2
x2
x1
JOLLY TA N K c o n c e a l e d c i s t e r n110 mm
or more
L (mm) X (mm)
200 400240 390300 360350 340400 300440 180
a
a
H I J
Ø38/46mm
Ø14/38mm
K
Fit the lid into place, taking care not to twist, kink or trap the cable.
Connect the fl exible fl ush pipe to the pan and the pan connector (not supplied with the cistern) to the waste outlet. Jollyfl ex is recommanded.
Position the control buttonon the right: for position see diagram and check against the measurements in box below.
Click the cable onto the pre-assembled button and clip the top fascia onto the unit. Fix the pan to the fl oor and seal with silicone as required. See trouble shooter in case of problem.
3 litre adjustment
6 litre adjustment
Test the complete cistern when installation is over
www.wirquin.comHELP
09/0
8 -
2124
44
340 mm
380
mm
130
mm
x1
Dual fl ush push button in chromed fi nishref: 19008101
Black cable for MW2 mechanismref: 10717443
Overfl ow washer for WIRQUIN fl ushing mechanismref: M25
TOPY fl oat valveref: 16300501
TOPY diaphragm washerref: 19066001