Post on 11-Dec-2021
EK-6
800-839-8823 www.creform.com
SV-22
I.D. Deburring Cutter
ID/OD DEBUR
I.D/O.D. Deburring Tool
CreformTools
G-�
se
CTIo
N
G
Creform Pipe should always be cut using a pipe cutter, band saw or chopsaw — never use a hand saw to cut pipe as this will frequently result in pipe sections not cut to the required lengths and pipe ends out of square.
These conditions can effect the fit and strength of your Creform structures.
Please read all instructions and familiarize yourself with proper procedures prior to using the Creform EPC Pipe Cutter or EK-1 Manual Pipe Cutter. ALWAYS WEAR APPROPRIATE EYE PROTECTION.
When cutting, always hold the longest length of pipe.
Electric ø28 Pipe Cutter
EPC1
EK-1
Manual ø28 & ø32 Pipe Cutter
EK-1A
Manual Pipe Cutter Blade Set
Electric Pipe Cutter Blade
EPC1A
SV-22A Replacement Blade
EK-6A Replacement Blade
I.D. Deburring Cutter for Drill
Manufacturer:Jet
Creform P/N:Bandsaw J1
Our Price:$445.00
UL listed single phase motor●
Exclusive design heavy-duty 14 gauge stand●
Large diameter wheels and built-in handle allowseasy movement
●
Front legs have adjustable leveling pads●
Ball bearing supported blade wheel●
Full adjustable ball bearing blade guides●
Heat treated and ground steel worm gear withbronze drive gear
●
Three blade speeds to choose from●
Automatic shut-off after cut●
Standard EquipmentVertical work table●
Carbon steel blade●
Adjustable material stop●
SpecificationsModel HVBS-56MStock Number 414458Round Capacity at 90 degrees (in): 5Round Capacity at 45 degrees (in): 3Rectangle Capacity at 90 degrees (in):5 x 6Rectangle Capacity at 45 degrees (in):5 x 3Throat Depth (in): 6Vertical Workable (in): 9-5/8 x 9-1/2Vise Swivels: 45 degreesBlade Size (in) 1/2 x .025 x 64-1/2Blade Wheel Diameter (in): 7-3/8Blade Speeds (SFPM): 80, 120, 200Blade Height (in): 25-1/2Floor Space Required (in): 19 x 44Motor: 1/2 HP, 1 Ph 115/230V Prewired 115VNet Weight (lbs): 115
Power Saw for Cutting Creform Pipe and Conveyor
Creform Corporation, PO Box 830, Greer, SC 29652-0830 www.Creform.comPhone:864-877-7405 Fax:964-877-3863
M6-L
6mm Hex Wrench
M6-L
6mm Hex Wrench, T-Handle
5MTM
Metric Tape Measure
Adhesive Bellows with Needle
BELLOW
CW-32
Caster Wrench for ESC Casters
800-839-8823 www.creform.com
CreformTools
G-2
se
CTIo
N
G
RTK1
Caster Wrench for YGR Casters
EK-20
NDL-1
Needle Spout, Adhesive
EY-204
Adhesive Bottle with Needle
5mm Hex Wrench
M5-L
Rubber Mallet
RM-01
5mm Hex Wrench, T-Handle
M5-T
In addition to the EPC Pipe Cutter and the EK-1 Manual Pipe cutter, the tools below are available from Creform, intended to make fabrication and construction of Creform Structures easier and faster.
RTK1C
RTK1A
RTK1B
Set: Ratchet Handle, 13mm Socket, 5mm Hex Bit
EK-6A
EK-6 EK-4BEK-4A
SU7-4000-SUS
EK-4
EK-3EK-2
ø28 Length(mm)
EK-2A EK-3A
800-839-8823 www.creform.comESD anti static
I-7
se
ctIo
n
I
Notes:• High temperature applications up to 300°F
(140°C).• Higher chemical resistance uses since material
is 304SS.• The pipe is grooved at joint locations to add
strength.
Stainless Steel Pipe
Material: Polished 304 Stainless Steel.Used to Form: General Creform Structures. Carts, workstations, flow racks, etc.Note: ø27 pipe. Standard length 4M.
Creform Standard 27mm Pipe Strength
* Proportional Limit refers to the point where any further force would permanently deform the pipe.
A Dimension Proportional Limit 900mm (2'11") 97kg (213 lbs.)
• The pipe rests freely at room temperature on two supports• A force is applied at 1/2 A at a speed of 50mm/min
Experimental Conditions
Manual Pipe Cutter for SUS Pipe
Manual Pipe Cutter Blade Set
Manual Grooving Cutter for SUS Pipe
Manual Grooving Cutter Blade Set
Electric Pipe Cutter - Groover for SUS Pipe
Dimensions are in millimeters.
creform
stAInLess steeL PIPe - 27mm
Electric SUS Pipe Cutter Blade Set
Electric SUS Pipe Grooving Cutter Blade Set
ID Deburring Tool for Electric Drill
Replacement Blade