Post on 19-Apr-2022
I n vac a r e ®
Bed rail Selection chart
As the leading producer of bed systems and components (bed, mattress and rails) to the home and long-term care industries, Invacare strives to ensure patient safety. The importance of proper patient assessment, correct installation and the ongoing review and maintenance of the complete bed system should never be overlooked. With millions of bed systems in both home and long-term care environments, awareness of the potential for entrapment is vital.
Bed Rail Entrapment can occur from issues with the bed, the rail or the mattress. Please note that replacing these rails will only address certain zones for potential entrapment. It is up to you, the provider, to ensure that your bed systems meet the FDA’s guidelines. As such, you will need to evaluate your inventory of beds and mattresses as well for compliance with the guidelines, especially as the three components (bed, rail and mattress) work together as a system.
Bed rail designs have changed over the years. Our goal is to inform you of these changes and request that you review your inventory of Invacare bed rails. If you currently use an older design, we ask that you stop using these and replace them with a newer design. The following pages depict some of the options available to you.
Potential Part Numbers: 6650 Replace with 6629
Note: 3 different designs exist Note: 6629 Rails utilize 7/8" tubing
Potential Part Numbers: 6629
Replace with part number 6629
Note: pre 2004, rails had 3 cross bars
Note: 2004 to present, rails have 4 cross bars
10.96 11.96
Half Length RailsPotential Part Numbers: 6630 pre 2003
Replace with 6630 current production
Note: pre 2003 rails had different dimensions and no spindle; from 2003 to present, dimensions have changed and an additional spindle was added to close the gap.
Full Length Rails
Potential Part Numbers: 6628, 6628-TSS
Replace with 6628, 6628-TSS, or 6629
Note: pre-2004 rails had 3 cross bars; 2004 to present rails have 4 cross bars
Note: 6628 Rails utilize 1" tubing
Invacare HOMecare DIvISIOn
Pre 2004 2004 – Present
OUt DAteD ImpROveD DeSIgn
3 Bar Design 4 Bar Design
11" Height 12" Height
Potential Part Numbers: IH5822, IH6802, and IH6803
Replace with IH6803A
5 1/2 TYP.
Potential Part Numbers: IH5744, IH5748, and IH5749
Replace with IH6803A, IH6808A, IH6815A, IH6816A
Note: If you have rails with a 5 1/2" spacing you should replace these with a different rail.
Note: Nylasar rails manufactured before June, 2005 had a 5 1/2" spacing between the rail attachment bolts. After June, 2005 the spacing was decreased to 5 1/4". While 5 1/4" spacing rails are suggested for use, they are no longer manufactured. If you need to replace 5 1/2" rails and do not currently have 5 1/4" rails, please replace with one of the following: IH6801A, IH6803A, IH6815A, IH6808A
5 1/2 TYP.
5.50 TYP.
5 1/4 TYP.
5 1/4 TYP.
5.25 TYP.
Invacare cOnTInUInG care DIvISIOnInvacare/Huntco Specific
5 1/2" Spacing 5 1/4" Spacing
OUt DAteD ImpROveD DeSIgn
Potential Part Numbers: IH5813, IH6807
Replace with IH6808A
Potential Part Numbers: IH5814, IH6800
Replace with IH6801A
Potential Part Numbers: IH5820, IH5830, IH5831, IH6805, IH6815, IH5821 and IH6806
Replace with IH6815A and IH6816A
OUt DAteD ImpROveD DeSIgn
Potential Part Numbers:IHARRLFUL, IHECRLFULL, IHARRLPAR, IHECRLPAR
Replace with current production in addition to Kit 71
Note: Use corner adapter kit to modify your rails
Note: Use only with Invacare® Solace® Prevention 2000 Series and higher mattresses
9902RR1-000-07CARROLL ASSIST RAIL WELDMENT - RIGHT11
DWGSPECIFICATIONTITLEQTY.ITM
VERETON NOISIVERETAD BY ECO
807PGPCASKROWDILOS NI NWARDER70 42 TPES
BNI 1 ETALP ROHCNA NETROHS )2 .0.12 SAW 0.02 MID )140 20 NAJ BW 534
A5.12 SAW 0.12 MID - 1 METI ETADPU30 80 LUJ BW 522
LERESAELER GED TNIAP WEN20 11 TCO BW 422
9932
RR1-010-26
1 OF 1
AC+
10/11/2002
DIMENSION IN IN INCHES - DO NOT SCALE
DRAWN BY:CHECKED BY:
CARROLL ASSIST RAIL PAINT - RIGHT
1/2/2004CREATED:
LONDON, ONT. N6E 1P5
DWG DATE:
-B.WELCH
SHEET
994 HARGRIEVE RD.
PHONE (519)659-1395
ANGLE +/- 0.25DWG.TITLE:
MAT'L:
PART:
ASME Y14.5M-1994
REV.
TOLERANCE X.X +/- 0.030 X.XX +/- 0.010 X.XXX +/- 0.005 X X/X +/- 1/32
RELEASED PRODUCTION
FILM BUILD 1.8 - 3.0 MIL
OR HENTZEN P80023TPN CARROLL BEIGE EPOXYERIE POWDER COATING #E103-G7 CARROLL EPOXY
NOTE: COATING SPECIFICATIONS
SURFACE PREP:PRE-TREAT WITH ZINC PHOSPHATE
PAINT:POWDER COAT COLOUR: SEMI GLOSS BEIGE
1
26.50
20.00
1.00
Uncontrolled Copy
Potential Part Numbers: IH5814, IH6800
Replace with current production if your rail looks like one pictured on the left side
Invacare cOnTInUInG care DIvISIOncarroll Healthcare Specific
2002-Present with Kit 71
OUt DAteD ImpROveD DeSIgn
Pre 2002
Invacare CorporationUSAOne Invacare WayElyria, Ohio 44035-4190(800) 333.6900
Canada570 Matheson Blvd. E.,Unit 8Mississauga, OntarioL4Z 4G4 Canada(800) 668.5324
©2011 Invacare Corporation. All rights reserved. Trademarks are identified by the symbols ™ and ®. All trademarks are owned by or licensed to Invacare Corporation unless otherwise noted. Specifications are subject to change without notification.Form No. 11-122110512