Post on 16-Nov-2021
1
Installation Instructions for 920E4 -LED AIC
Round or Square 4”
E4_-L_AI 1.5
Install the Housing with Adjustable Bars
1
2
3
Slide the inner adjustable bar completely through thethree housing clasps. Make sure the nail is on top.
Slide and push the outer adjustable bar completely ontothe inner adjustable bar so that the tab clicks into placebehind the stop point.This will prevent the adjustable barsfrom coming apart.
Repeat steps 2 & 3 for the other side of the housing.
HOUSING CLASP
HOUSING1A INNER ADJUSTABLE BAR
OUTER ADJUSTABLE BAR
TAB
STOP POINT
2
3
NAIL
1
1D
1B
COLLAR
NAIL
JOISTNAIL
4 4
5
5
NOTE: The adjustable bars can be mounted to
joists that are spaced 16" - 24" apart.
Align the bottom of the end plates with the bottom of theceiling joists.
Level the adjustable bars and, with a hammer, tap the nailscompletely into the joists to secure the adjustable bars inplace.
4
5
4
5
Type Adjustable HousingICwith LampLED
CAUTION RISK OF FIRE-
This product must be installed in accordance withthe applicable installation code by a person familiarwith the construction and operation of the productand the hazards involved.
Use minimum 90°c supply conductors.
G P I :ENERAL RODUCT NFORMATION
This product is suitable for indoor locations.
This product can be dimmed with a standard electronic dimmer.
This instruction shows a typical installation.
2
COLLAR
8
8
Adjust the collar position (horizontal position) by slidingthe housing on adjustable bars.
When the desired location is achieved, tighten the two #6self tapping screws to lock the housing onto the adjustablebars.
7
8
NOTE: See step 3 to align multiple housings
using the notches.
Carefully cut and remove the zip ties to remove theshipping plate.
6
1C
PRESSTOUNLOCKTILTZIP TIE
SHIPPING PLATE
HOUSINGADJUSTABLE BAR
7
COLLAR
NOTCH
1D
PRESSTOUNLOCKTILT
PR
ES
STO
UN
LOC
KTIL
T
3
Slightly loosen the wing nut to slide the butterfly bracketup or down.
After achieving the proper location, tighten the wing nutto secure the butterfly bracket in place.
Repeat steps 1 and 2 for the other butterfly bracket.
Utilize the butterfly brackets to install the housing inaccordance with local electrical codes.
BUTTERFLYBRACKET
COLLAR
WING NUT
1
2
NOTCH
Install the Housing with ButterflyBrackets
2A
1
2
3
4
NOTE: Skip this section if installing the housing
with adjustable bars.
3
NOTE: See step 3 to align multiple housings
using the notches.
PRESSTOUNLOCKTILT
3A 2x THUMB NUT
ADJUSTMENTNOTCH
Align Multiple Housings (Optional)
1
1
3
3
2
The alignment of the collars may be adjusted by reachinginto the housing and loosening the two thumb screws.Note: Adjustment of the lamp and heat sink may benecessary to access the thumb nuts. See Section 6
Rotate the collar (up to 45°) and align with other fixturesusing the notches in the collar with a laser or string.
Re-tighten the two thumb screws.
1
2
3
4
Connect Power to the Housing
Install the conduit to the housing electrical box.
Run the power line wires into the housing electrical box.
2
WARNING: RISK OF FIRE: When using the
housing electrical box for power feed through,
use 4 - #12 , or 6 - #14 branchMAX AWG AWG
circuit wires.
3
Push up on the tabs on the electrical box and remove theelectrical box cover.
1
4A
TABS
ELECTRICALBOX COVER
1
4B
3
2
5
Connect the neutral power line wire to the whitetransformer wire with a wire nut.
Connect the hot power line wire to the black thermalprotector wire with a wire nut.
Make sure that housing is grounded in accordance withlocal electrical codes.
For models with a 0-10V dimming driver, use the purpleand gray wire to connect to a compatible dimmer.
Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.
Skip to section 5.
4
6
5
7
8
4C
For Citizen and Xicato see section 4CLED
For Lumenetix Warm Color Dimming see section 4DLED
For Lumenetix Programmable White see section 4ELED
4D
Connect the neutral power line wire to the whitetransformer wire with a wire nut.
Connect the hot power line wire to the black transformerwire with a wire nut.
Make sure that housing is grounded in accordance withlocal electrical codes.
For dimming, use the purple and gray wire to connect to acompatible dimmer.
Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.
Skip to section 5.
10
12
11
13
14
15
13
11
12
10
75
46
Connect the neutral power line wire to the whitetransformer wire with a wire nut.
Connect the hot power line wire to the black transformerwire with a wire nut.
Make sure that housing is grounded in accordance withlocal electrical codes.
For dimming, use the purple and gray wires to connect to acompatible dimmer.
For white CCT (Color Control), use the blue and white wiresto connect to a compatible dimmer, see wiring diagram inSection 8.
For remote CCT (Color Control), hue, and saturation control,use the LCT handheld unit (Light Commissioning Tool soldseparately) and tie the blue and white wires together.
For DMX control wiring, use the following wires:
�Orange/White (DMX +)�Orange (DMX -)�Brown (Gnd)� Tie the Purple, Grey, and White wires together.
Replace the electrical box cover. Make sure that the topedge of the cover snaps under the tab.
16
18
17
19
20
21
22
4E
16
21
19
2121
18
20
17
9
6
CUT OUT
Insert the plaster ring completely into the collar/ceilingand secure them in place with the provided set screws andAllen wrench.
1
ROUND PLASTER RING SQUARE PLASTER RING
CUT OUT
NOTE: Longer set screws have been provided for
instances where the plaster ring does not reach the
collar and must be secured to the inside of the ceiling
cutout. Use the short set screws if the trim is installed in
the collar.
6A
PRESSTOUNLOCKTILT
PRESSTOUNLOCKTILT
PRESSTOUNLOCKTILT
SET SCREW
ALLENWRENCH
1
SHORT SET SCREW
TAB
TRIM HOLDER
LONG SET SCREW
TAB
CEILING
Install Drywall
5A
4-1/2"
ROUND COLLAR SQUARE COLLAR
For round trims, mark a 4-1/2" diameter circle on drywall.Cut out the marked section.For square trims, mark a 4-1/2" square on drywall. Cut outthe marked section.
1
4-1/2"
Align the cut out section of drywall with the collar andinstall drywall.
2
5B
2
DRYWALL COLLAR JOIST
PRESSTOUNLOCKTILT
PRESSTOUNLOCKTILT
Install Plaster Ring(For Flangeless Versions)
7
LE
NS
LO
CK
LE
NS
LO
CK
Plug the collar with the provided dust shield.
Properly plaster onto the plaster ring and drywall.
2
6C
Finish around the collar to match drywall.4
4 4
3
6B
LE
NS
LO
CK
PRESSTOUNLOCKTILT
PRESSTOUNLOCKTILT
22
PRESSTOUNLOCKTILT
Adjust the Lamp Position
BUCKETHANDLE
1
7A
BUCKETHANDLE
1 Push up the and heat sink to ensure that they are inLEDthe highest position.
LE
NS
LO
CK
PRESS TOUNLOCK TILT
7B
2TILT ADJUSTMENTLEVER
INDICATOR
2
010
203040
o
o
o
oo
2 For proper wall wash positioning, unlock the tiltadjustment lever by pressing where indicated using afinger or screwdriver to tilt until 15° angle is reached.
PRESSTOUNLOCKTILT
7C
ROTATION LOCK 3
4
NOTE: Lamp housing can rotate 361° horizontally.
3 Pull the rotation lock down to unlock the lamp housing.
Rotate the lamp housing horizontally.When the desiredposition is achieved push the rotation lock up to lock thelamp housing in place.
4
8
Wiring Diagrams for Lumenetix LED
8AE
lem
en
t4"
LE
D–
Lu
men
eti
x–
Warm
Dim
&P
rog
ram
mab
le W
hit
e
for
sin
gle
0-1
0v
Dim
me
r
Exte
rna
l H
ot
-Bla
ck
Exte
rna
l C
om
mo
n
-W
hite
Vio
let
Wire
0-1
0v D
imm
ing
Gre
y W
ire
Com
mon
White W
ire
Blu
e W
ire
Red W
ire
-Positiv
e12v
Blu
e W
ire
-Negative
12v
Blu
e W
ire
-Ne
ga
tive
12
v
Blu
e W
ire
-Negative
12v
L.T.F
Dimmable LED D r i v e r
255LEDD*20W12V
Exte
rna
l G
rou
nd
-G
ree
nG
rou
nd
pro
vid
ed
in e
ach
ho
usin
g
-
+V
iole
t
Wire
Gre
y
Wire
Sw
itched
hot
L.T.F
Dimmable LED D r i v e r
255LEDD*20W12V
L.T.F
Dimmable LED D r i v e r
255LEDD*20W12V
DM
X C
ontr
ol Lin
es
Org
/Wht
=D
MX
+
Ora
nge
=D
MX
-
Bro
wn
=S
ign G
nd
Red W
ire
-Positiv
e12v
Re
d W
ire
-Po
sitiv
e1
2v
DM
X C
on
tro
l L
ine
s
Org
/Wh
t=
DM
X+
Ora
ng
e=
DM
X-
Bro
wn
=S
ign
Gn
d
DM
X C
on
tro
l L
ine
s
Org
/Wh
t=
DM
X+
Ora
ng
e=
DM
X-
Bro
wn
=S
ign
Gn
d
Wh
ite
Wire
Blu
e W
ire
White W
ire
Blu
e W
ire
9
8B4
10
Notes
11
Notes
12
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, 60077IL
847.410.4400
www.element-lighting.com© 2016 Tech Lighting, L.L.C. All rights reserved.The "Element" graphicis a registered trademark of Element. Element reserves the right tochange specifications for product improvements without notification.
A Generation Brands Company