Post on 13-Jan-2022
Industrial/Commercial Evaporative CoolersSpecification Guide
Industrial/Commercial Evaporative CoolersSpecification Guide
MODULARCONFIGURATIONS
The unique modular design of thedual inlet side- and down-draft
models are easy to reconfigure for difficult or customized
installations.
1. CONSTRUCTION – Heavy gauge galvanized steel isused for cabinet panels and other load bearing components. Vacuum-formed ABS plastic water reservoirs and thick polystyreneevaporative media shields keep water from coming into contact withthe steel cabinet for long-lasting durability.
2. EVAPORATIVE MEDIA – The cellulose paper of theevaporative media is treated to ensure a high water absorption rateand to resist biological degradation.
3. FINISH – All steel components (excluding the blower wheel,shaft, and pulley) are chemically treated and covered with anelectrostatically-applied polyester finish at a thickness of 1 to 1.5mil to protect the cooler from scratches and corrosion. This finishmeets or exceeds requirements for the following tests:• 1000-Hour Salt Spray Test-ASTM B117• Abrasion Resistance Test-ASTM 4060-84• Impact Resistance Test-ASTM D2794• 2400-Hour Imersion Test-ASTM D870• Adhesion Test-ASTM D3359
OINTSDVANTAGE
SAS/SAD 100SAS/SAD 10012SAS/SAD 150
AS/AD 150AS/AD 15012AS/AD/AU 20012
SAS/SAD 15012AS/AD 100AS/AD 10012
SPECIFICATION GUIDE FOR MODELS:
Double Inlet Configuration
Single Inlet Configurationconnect
BLOWER UNIT
BLOWER UNIT
INLET UNIT
INLET UNIT
INLET UNIT
rotateremove
BLOWER UNIT
INLET UNIT
PA
MASTERCOOL COOLERS ARE MADE BY THEBEST: CHAMPION COOLER
One of the largest manufacturers of evaporative coolers, ChampionCooler has produced evaporative coolers that deliver highperformance results and long-lasting durability for over 40 years.Champion’s engineering, design, and production efforts are directedat the continued manufacture of products that deliver maximumperformance with minimum maintenance.
The performance or Sensible Heat Capacity of any evaporative cooler isa function of both the CFM and the efficiency, which should be consideredas part of the sizing process. To help ensure proper sizing of a MasterCool,use the Index on the following page to locate Performance Data and SizingTables for a specific MasterCool model. Follow the procedure below todetermine the cooler size.
1. Determine design conditions.• Outside Dry-Bulb• Outside Wet-Bulb• Inside Dry-Bulb (TI)
2. Determine the design Sensible Heat Load (Btuh).3. Determine the cooler leaving air temperature (LAT) from the tables.
EXAMPLE
• Outside Dry-Bulb = 105• Outside Wet-Bulb = 65• Inside Dry-Bulb = 80Determine the number of AD100 UltraCool coolers with 2 horsepower
motors required to cool 125,000 Btuh heat load. Assume .5" (water) externalstatic pressure.
Using the Sizing Tables, the following information should be calculated:
LAT = 72CFM = 7368SHC = 1.08(80-72)7368 = 63,660 BtuhNumber of Coolers = 125,000/63,660 = 2
4. Determine CFM from the performance tables.5. Calculate Sensible Heat Capacity of cooler using: SHC =1.08(TI-LAT)CFM6. Determine the number of coolers by dividing the Sensible Heat Load by the Sensible Heat Capacity.
NSTRUCTIONSIZING
Q
D
E
E
A
F
G
X
D
S
QD
C
R
C
N
B
A
E E
N
T
W
H
UBPW
J
L
Y
M
J
SAD OUTLETSAD OUTLET
SASOUTLET
TOP VIEW WEIV EDISWEIV TNORF
* All measurements in inches.
D4545
48 1/4
48 1/4
H100W
10012W150W
15012W
WETMODULENUMBER
SAS/SAD 100BSAS/SAD 10012BSAS/SAD 150BSAS/SAD 15012B
BLOWERMODEL
NUMBERCABINET
W44445454
63 3/8
67 3/8
66 5/8
70 5/8
C(SAS)13 19/32
13 19/32
16 13/16
16 13/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
21 3/4
21 3/4
26 7/8
26 7/8
U(SAD)21 11/32
21 11/32
19 5/32
19 5/32
EP(SAD)11 5/8
11 5/8
10 11/16
10 11/16
1 29/32
1 29/32
2 7/32
2 7/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
12 1/2
16 1/2
12 1/2
16 1/2
X
MEDIADIMENSION
Y44 3/4
44 3/4
4848
36 5/8
36 5/8
46 3/8
46 3/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
S
ELECTRICSERVICE
T21 1/2
21 1/2
23 1/8
23 1/8
5 5/32
5 5/32
5 5/32
5 5/32
N4 3/4
4 3/4
4 3/4
4 3/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
42425252
DIMENSIONAL DATA*
PERFORMANCE Certified Air Delivery At Various Increments Of Static Pressure (Inches Static Pressure Water Gauge)INDEX TABLEINDEX TABLE
CFM
SAS/SAD 100PAGE 2
SAS/SAD 10012PAGE 4
SAS/SAD 150PAGE 6
SAS/SAD 15012PAGE 8
AS/AD 100PAGE 1
AS/AD 10012PAGE 3
AS/AD 150PAGE 5
AS/AD 15012PAGE 7
AS/AD/AU20012PAGE 9
MODEL& PAGE NO.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"
Performance shown is for installation type B - free inlet, ducted outlet. Power rating (BHP) does not includedrive losses. Performance ratings do not include the effects of appurtenances in the airstream.
CFM
537759186774
537159116767
707277838910N/AN/A
699777028817N/AN/A
774585249758
11569
743181789362
11099
11405130571548017719
11375130201543817672
16267192862207724301
CFM
512156846574
506456276513
6622737285489476N/A
6539728684559375N/A
753083339596
11463
725580249235
11001
10892126001508217364
10905126041508417360
15716188202167023929
CFM
486354516366
479453756286
6203698782059159N/A
6087687680919044N/A
727581099407
11285
705278429075
10868
10463122041473517050
10482122251474917060
15200183712127023562
CFM
460552156164
453651426076
5769660278708855N/A
5603645077348719N/A
700478689204
11121
683576498914
10736
10064118441441016756
10079118651443416777
14696179432088823204
CFM
433649805956
426949075872
5298619975338555N/A
5051599473598389N/A
672976188990
10950
661174508744
10598
9671114971410616479
9678115141413316505
14190175182051422866
CFM
405847345751
398546635666
4777576471828244N/A
4415547769618043N/A
646073688773
10773
637672448572
10457
9276111531381016214
9265111651383816242
13665170922014222528
375444795537
366743995456
4201528568127924N/A
37174893652576839377
619371238556
10592
613170308393
10313
8874108151352015947
8830108071354015983
13110166611976922190
0.8"
CFM
309739245095
295238095008
30414231599372369032
24973637552768698751
564666388124
10224
561065808024
10016
8006101131294815440
7867100581289915463
11886157521901521510
0.9"
CFM
--36194859
259134804755
25223699553768668741
20133085497664168407
535763897913
10039
5327634378279862
75309741
1265915188
73259651
1264015207
11194152721862921171
1.0"
CFM
--33074613
226131454497
20403199506764708436
15712609442559328046
5045613776989856
5031609576319709
70179361
1236114937
67539220
1232814947
10450147601822920823
0.7"
CFM
342942095320
331841155238
36074764641675929315
30584260605072939070
592368788340
10407
587768098209
10165
8456104671323415694
8366104401324615724
12521162111939521852
HOW TO USETHIS INDEX
Using the coolingrequirement variables ofCooling Feet per Minute
and External StaticPressure (shown as inches
of water), locate thespecific MasterCool model
required and itscorresponding page
number. Turn to theindicated page for specific
Performance Data andSizing Tables. Follow theSizing Instructions on the
front inside cover todetermine the MasterCool
product for any coolinginstallation.
AB
LE
IN
DE
X
AD OUTLETEE A
Q
XD
G
F
GD
S
QW
R
C
J JN
P
B
B
AL
MME E
N
Y
L
P
D
H
UB
T
AD OUTLET
C
TOP VIEW WEIV EDISWEIV TNORF BLOWERSECTION
AS OUTLET
AU OUTLET
* All measurements in inches.
D4545
48 1/4
48 1/4
60 1/4
H100W
10012W150W
15012W20012W
WETMODULENUMBER
AS/AD 100BAS/AD 10012BAS/AD 150BAS/AD 15012BAS/AD/AU 20012B
BLOWERMODEL
NUMBERCABINET
W44445454
59 1/4
8290
85 1/4
93 1/4
105 1/4
C(AS)13 19/32
13 19/32
16 13/16
16 13/16
18 11/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
U(AD)21 11/32
21 11/32
19 5/32
19 5/32
25 1/4
EP(AU)11 5/8
11 5/8
10 11/16
10 11/16
14 1/4
N/AN/AN/AN/A
24 29/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
30 1/8
12 1/2
16 1/2
12 1/2
16 1/2
16 1/8
X
MEDIADIMENSION
Y44 3/4
44 3/4
484860
36 5/8
36 5/8
46 3/8
46 3/8
51 5/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
18 5/8
S
ELECTRICSERVICE
T39 7/8
43 7/8
41 1/2
45 1/2
51 5/8
5 5/32
5 5/32
5 5/32
5 5/32
5 5/32
N23 1/4
27 1/4
23 1/4
27 1/4
27 1/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
4 3/4
42425252
57 1/4
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.
1-1/2 H.P. MOTOR / CFM-
OUTDOOR WET-BULB
2 H.P. MOTOR / CFM-SP*
OUTDOOR WET-BULB
3 H.P. MOTOR / CFM-SP*
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models AS/AD 100 include the affects of an 8 inch thick evaporative media on the inlet. & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
ASMODEL
BELTAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
20/11-106.6-6/3
24/13.2-127.5-6.8/3.410.6-9.6/4.8
16.7-7-15.2/7.6
7/87/87/87/81 1/81 1/8
131333
115/208-230208-230/460115/208-230208-230/460208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
111111
414049448387
110459110463-9110460
110464-9110465-9110466-9
1 1/21 1/2
2235
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8433455523590
443465533600
422445513580
412434502569
D8450D8450D8550D8600
A82B83B86B87
ASMODEL
BELTA76B77B80B81
ADMODEL
BELT7/87/8
1 1/81 1/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
1-1/2235
391414482549
401424492559
454475543610
464485553620
475495563630
485506574641
496516584651
506526594661
3DI-103DI-153DI-203DI-25
SHEAVEBORE
CHAMPION-ADPULLEY-BELT
KIT NO.3DI-303DI-353DI-403DI-45
CHAMPION-ASPULLEY-BELT
KIT NO.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 2 Required.
757711792282338444
OUTDOOR WET-BULB656922723374447654
5562336444
––––
757710792181318341
656921713173417551
5561316341––––
757710791981288338
656919712873387547
5561286338––––
11569 / 0 10773 / .5 9856 / 1.05 H.P. MOTOR / CFM-SP*
727581099407
11285
384418473555
373408465549
753083339596
11463
A76B77B80B81
A82B83B86B87
706710723739
1 1/2235
774585249758
11569
364400458543
700478689204
11121
397429482563
672976188990
10950
409441492570
646073688773
10773
422452502578
619371238556
10592
434464512587
564666388124
10224
460486532603
535763897913
10039
474498542612
5045613776989856
489510552620
592368788340
10407
447475522595
7577
8791580238231
656915702372317438
5560236231––––
75777
781380208126
656813702071267333
5560206126––––
7576
5781079168021
656810691670217226
5559166021––––
7745 / 0 6460 / .5 5045 / 1.0
7577
8791781258233
656917712572337442
5561256233––––
75777
791580228229
656915702272297437
5560226229––––
75776
781280198125
656812701971257331
5560196125
–––
8524 / 0 7368 / .5 6137 / 1.0
7577
9791981288338
656919712873387547
5561286338––––
7577
9791781268334
656917712673347443
5561266334––––
75778
791580238231
656915702372317438
5560236231
––––
9758 / 0 8773 / .5 7698 / 1.0
When the Cooler Model No, Motor H.P.,
Q
D
E
E
A
F
G
X
D
S
QD
C
R
C
N
B
A
E E
N
T
W
H
UBPW
J
L
Y
M
J
SAD OUTLETSAD OUTLET
SASOUTLET
TOP VIEW WEIV EDISWEIV TNORF
* All measurements in inches.
D4545
48 1/4
48 1/4
H100W
10012W150W
15012W
WETMODULENUMBER
SAS/SAD 100BSAS/SAD 10012BSAS/SAD 150BSAS/SAD 15012B
BLOWERMODEL
NUMBERCABINET
W44445454
63 3/8
67 3/8
66 5/8
70 5/8
C(SAS)13 19/32
13 19/32
16 13/16
16 13/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
21 3/4
21 3/4
26 7/8
26 7/8
U(SAD)21 11/32
21 11/32
19 5/32
19 5/32
EP(SAD)11 5/8
11 5/8
10 11/16
10 11/16
1 29/32
1 29/32
2 7/32
2 7/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
12 1/2
16 1/2
12 1/2
16 1/2
X
MEDIADIMENSION
Y44 3/4
44 3/4
4848
36 5/8
36 5/8
46 3/8
46 3/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
S
ELECTRICSERVICE
T21 1/2
21 1/2
23 1/8
23 1/8
5 5/32
5 5/32
5 5/32
5 5/32
N4 3/4
4 3/4
4 3/4
4 3/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
42425252
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
75775
791081158321
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
656910711573217526
5561156321
––––
75774
798
80128216
6569
8701272167421
5560126216––––
75762
775
797
809
6567
569
770
97112
55597
609––––
5435 / 0 4118 / .5 2197 / 1.0OUTDOORDRY BULB
TEMP.
3/4 H.P. MOTOR / CFM-SP*
75776
791182178422
OUTDOOR WET-BULB656911721774227628
5562176422
––––
7577
579
981148319
65699
711473197523
5561146319––––
7577
378
680
98113
6568
670
971137316
55609
6113––––
5983 / 0 4856 / .5 3092 / 1.01 H.P. MOTOR / CFM-SP*
75776
801382198425
OUTDOOR WET-BULB657013721974257732
5562196425
––––
7577
6791181178422
656911711774227628
5561176422––––
75774
799
81138318
65699
711373187522
5561136318
––––
6848 / 0 5942 / .5 4639 / 1.01-1/2 H.P. MOTOR / CFM-SP*
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models SAS/SAD 100 include the affects of an 8 inch thick evaporative media on the inlet. , & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table b elow.
RPMCFM RPM486354516366
376409463
RPM364398453
CFM512156846574
CFMB77B77B77
SASMODEL
BELTB83B83B83
SADMODEL
BELT480483498
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"
3/41
1 1/2
RPM537759186774
352388444
CFM RPM460552156164
389421472
CFM RPM433649805956
402432482
CFM RPM405847345751
415444492
RPM375444795537
430456502
0.8"CFM RPM
309739245095
469485524
0.9"CFM RPM
--36194859
--503536
1.0"CFM RPM
--33074613
--523548
0.7"CFM
342942095320
448470513
13.8/7.6-6.96.9
3.5-3.2/1.616/8
84.6-4.2/2.1
5/85/85/85/85/87/8
113113
115/208-230230
208-230/460115/230
230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
121121
242920282934
110455110456110461110457110458
110462-9
3/43/43/4111
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
20/11-106.6-6/3
7/87/8
13
115/208-230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
11
4140
110459110463-9
1 1/21 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8343455343455
353465353465
333445333445
323434323434
8350K8450K8350
8450K
B83B83B83B83
SASMODEL
BELTB77B77B77B77
SADMODEL
BELT5/8*5/8*7/8*7/8*
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
3/4, 13/4, 1
11, 1 1/2
303414303414
313424313424
364475364475
374485374485
384495384495
394506394506
404516404516
414526414526
3DI-903DI-95
3DI-1003DI-105
SHEAVEBORE
CHAMPION-SADPULLEY-BELT
KIT NO.3DI-1103DI-1153DI-1203DI-125
CHAMPION-SASPULLEY-BELT
KIT NO.
*When selecting 1 H.P. motor, be sure to select Pulley-Belt Kit with same pulley bore as shaft size of motor selected.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water.
Pumps - 1 Required.
When the Cooler Model No, Motor H.P.
LAT = Cooler Discharge Temperature.
AD OUTLETEE A
Q
XD
G
F
GD
S
QW
R
C
J JN
P
B
B
AL
MME E
N
Y
L
P
D
H
UB
T
AD OUTLET
C
TOP VIEW WEIV EDISWEIV TNORF BLOWERSECTION
AS OUTLET
AU OUTLET
* All measurements in inches.
D4545
48 1/4
48 1/4
60 1/4
H100W
10012W150W
15012W20012W
WETMODULENUMBER
AS/AD 100BAS/AD 10012BAS/AD 150BAS/AD 15012BAS/AD/AU 20012B
BLOWERMODEL
NUMBERCABINET
W44445454
59 1/4
8290
85 1/4
93 1/4
105 1/4
C(AS)13 19/32
13 19/32
16 13/16
16 13/16
18 11/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
U(AD)21 11/32
21 11/32
19 5/32
19 5/32
25 1/4
EP(AU)11 5/8
11 5/8
10 11/16
10 11/16
14 1/4
N/AN/AN/AN/A
24 29/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
30 1/8
12 1/2
16 1/2
12 1/2
16 1/2
16 1/8
X
MEDIADIMENSION
Y44 3/4
44 3/4
484860
36 5/8
36 5/8
46 3/8
46 3/8
51 5/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
18 5/8
S
ELECTRICSERVICE
T39 7/8
43 7/8
41 1/2
45 1/2
51 5/8
5 5/32
5 5/32
5 5/32
5 5/32
5 5/32
N23 1/4
27 1/4
23 1/4
27 1/4
27 1/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
4 3/4
42425252
57 1/4
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models AS/AD 10012 include the affects of a 12 inch thick evaporative media on the inlet. , & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
ASMODEL
BELTAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
20/11-106.6-6/3
24/13.2-127.5-6.8/3.4
10.6-9.6/4.816.7-15.2/7.6
7/87/87/87/81 1/81 1/8
131333
115/208-230208-230/460115/208-230208-230/460208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
111111
414049448387
110459110463-9110460
110464-9110465-9110466-9
1 1/21 1/2
2235
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8433455523590
443465533600
422445513580
412434502569
D8450D8450D8550D8600
A82B83B86B87
ASMODEL
BELTA76B77B80B81
ADMODEL
BELT7/87/8
1 1/81 1/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
1-1/2235
391414482549
401424492559
454475543610
464485553620
475495563630
485506574641
496516584651
506526594661
3DI-103DI-153DI-203DI-25
SHEAVEBORE
CHAMPION-ADPULLEY-BELT
KIT NO.3DI-303DI-353DI-403DI-45
CHAMPION-ASPULLEY-BELT
KIT NO.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 2 Required.
OUTDOOR WET-BULB
705278429075
10868
400436494581
390427487575
725580249235
11001
A76B77B80B81
A82B83B86B87
801805818834
1 1/2235
743181789362
11099
382421482571
683576498914
10736
411446502587
661174508744
10598
424457511594
637672448572
10457
437468520601
613170308393
10313
450480531609
561065808024
10016
477504551625
5327634378279862
492517562634
5031609576319709
507529672643
587768098209
10165
464492541617
75768
771778257934
656717682569347042
5558255934––––
7576
7771478217928
656714682169287035
5558215928––––
7576
6771177177822
656711671768226928
5557175822––––
7431 / 0 6376 / .5 5031 / 1.01-1/2 H.P. MOTOR / CFM-SP*
7576
9771878287937
656718682869377046
5558285937––––
7576
8771678247932
656716682469327040
5558245932––––
7576
7771378207927
656713682069276933
5558205927
–––
8178 / 0 7244 / .5 6095 / 1.02 H.P. MOTOR / CFM-SP*
757611772178327942
656721683269427053
5558325942––––
75769
771978287938
656719682869387047
5558285938––––
75768
771778257933
656717682569337042
5558255932
––––
9362 / 0 8572 / .5 7631 / 1.03 H.P. MOTOR / CFM-SP*
757612772578378049
656725683770497162
5558376049––––
757611772378347946
656723683469467157
5558345946
––––
757611772178327942
656721683269427053
5558325942
––––
11099 / 0 10457 / .5 9709 / 1.05 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H.P.
Q
D
E
E
A
F
G
X
D
S
QD
C
R
C
N
B
A
E E
N
T
W
H
UBPW
J
L
Y
M
J
SAD OUTLETSAD OUTLET
SASOUTLET
TOP VIEW WEIV EDISWEIV TNORF
* All measurements in inches.
D4545
48 1/4
48 1/4
H100W
10012W150W
15012W
WETMODULENUMBER
SAS/SAD 100BSAS/SAD 10012BSAS/SAD 150BSAS/SAD 15012B
BLOWERMODEL
NUMBERCABINET
W44445454
63 3/8
67 3/8
66 5/8
70 5/8
C(SAS)13 19/32
13 19/32
16 13/16
16 13/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
21 3/4
21 3/4
26 7/8
26 7/8
U(SAD)21 11/32
21 11/32
19 5/32
19 5/32
EP(SAD)11 5/8
11 5/8
10 11/16
10 11/16
1 29/32
1 29/32
2 7/32
2 7/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
12 1/2
16 1/2
12 1/2
16 1/2
X
MEDIADIMENSION
Y44 3/4
44 3/4
4848
36 5/8
36 5/8
46 3/8
46 3/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
S
ELECTRICSERVICE
T21 1/2
21 1/2
23 1/8
23 1/8
5 5/32
5 5/32
5 5/32
5 5/32
N4 3/4
4 3/4
4 3/4
4 3/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
42425252
DIMENSIONAL DATA*
AD
10
01
2
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
RPMCFM RPMRPMCFMCFM
SASMODEL
BELTSAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
13.8/7.6-6.96.9
3.5-3.2/1.616/8
84.6-4.2/2.1
5/85/85/85/85/87/8
113113
115/208-230230
208-230/460115/230
230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
121121
242920282934
110455110456110461110457110458
110462-9
3/43/43/4111
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
20/11-106.6-6/3
7/87/8
13
115/208-230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
11
4140
110459110463-9
1 1/21 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8343455343455
353465353465
333445333445
323434323434
8350K8450K8350
8450K
B83B83B83B83
SASMODEL
BELTB77B77B77B77
SADMODEL
BELT5/8*5/8*7/8*7/8*
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
3/4, 13/4, 1
11, 1 1/2
303414303414
313424313424
364475364475
374485374485
384495384495
394506394506
404516404516
414526414526
3DI-903DI-95
3DI-1003DI-105
SHEAVEBORE
CHAMPION-SADPULLEY-BELT
KIT NO.3DI-1103DI-1153DI-1203DI-125
CHAMPION-SASPULLEY-BELT
KIT NO.
*When selecting 1 H.P. motor, be sure to select Pulley-Belt Kit with same pulley bore as shaft size of motor selected.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will an amount equal to 10% of water consumption at any design condition is considered sufficient for average water.
LAT = Cooler Discharge Temperature.
Pumps - 1 Required.
479453756286
386420475
374410466
506456276513
B77B77B77
B83B83B83
527530545
3/41
1 1/2
537159116767
362359457
453651426076
397431484
426949075872
410441494
398546635666
423453503
366743995456
439465513
295238095008
481495534
259134804755
507514546
226131454497
534536560
331841155238
458479523
75766
771278177923
656712681769237029
5558175923
––––
7576
6771278127916
656712681769167020
5558135923––––
7576
276
577
778
9
65665
677
689
6811
55577
589––––
5377 / 0 4007 / .5 2120 / 1.0
7576
6771378197925
656713681969257132
5558195925––––
7576
6771078157920
656713681569207025
5558195920
––––
7576
577
778107813
656710681068136916
5558165813––––
5917 / 0 4712 / .5 2970 / 1.01 H.P. MOTOR / CFM-SP*
75767
771479228029
656714692270297136
5559226029––––
7576
6771278188025
656712681870257131
5558186025
––––
75765
771078157919
656710681569197024
5558155919
––––
6761 / 0 5761 / .5 4447 / 1.01-1/2 H.P. MOTOR / CFM-SP*3/4 H.P. MOTOR / CFM-SP*
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models SAS/SAD 10012 include the affects of a 12 inch thick evaporative media on the inlet. & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below. When the Cooler Model No, Motor H.P.
Use amperage shown on motor nameplate to determine motor protector.
vary with different water sources, but
AD OUTLETEE A
Q
XD
G
F
GD
S
QW
R
C
J JN
P
B
B
AL
MME E
N
Y
L
P
D
H
UB
T
AD OUTLET
C
TOP VIEW WEIV EDISWEIV TNORF BLOWERSECTION
AS OUTLET
AU OUTLET
* All measurements in inches.
D4545
48 1/4
48 1/4
60 1/4
H100W
10012W150W
15012W20012W
WETMODULENUMBER
AS/AD 100BAS/AD 10012BAS/AD 150BAS/AD 15012BAS/AD/AU 20012B
BLOWERMODEL
NUMBERCABINET
W44445454
59 1/4
8290
85 1/4
93 1/4
105 1/4
C(AS)13 19/32
13 19/32
16 13/16
16 13/16
18 11/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
U(AD)21 11/32
21 11/32
19 5/32
19 5/32
25 1/4
EP(AU)11 5/8
11 5/8
10 11/16
10 11/16
14 1/4
N/AN/AN/AN/A
24 29/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
30 1/8
12 1/2
16 1/2
12 1/2
16 1/2
16 1/8
X
MEDIADIMENSION
Y44 3/4
44 3/4
484860
36 5/8
36 5/8
46 3/8
46 3/8
51 5/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
18 5/8
S
ELECTRICSERVICE
T39 7/8
43 7/8
41 1/2
45 1/2
51 5/8
5 5/32
5 5/32
5 5/32
5 5/32
5 5/32
N23 1/4
27 1/4
23 1/4
27 1/4
27 1/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
4 3/4
42425252
57 1/4
DIMENSIONAL DATA*
D 1
50
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models AS/AD 150 include the affects of an 8 inch thick evaporative media on the inlet. & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
ASMODEL
BELTAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
24/13.2-127.5-6.8/3.410.6-9.6/4.8
16.7-15.2/7.624.2-22/11
7/87/81 1/81 1/81 3/8
13333
115/208-230208-230/460208-230/460208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
11111
49448387121
110460110464-9110465-9110466-9110470-9
2235
7 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8325381381437493
333390390446502
316373373429485
308364364420476
D8400D8450D8450D8550D8600
B96B96B100B100B101
ASMODEL
BELTB90B90B92B93B95
ADMODEL
BELT7/87/8
1 1/81 1/81 3/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
2235
7-1/2
291347347403459
299356356412468
342398398454510
350407407463519
359415415471527
367424424480536
376432432488544
384441441497553
3DI-503DI-523DI-563DI-603DI-65
SHEAVEBORE
CHAMPION-ADPULLEY-BELT
KIT NO.3DI-703DI-723DI-753DI-803DI-86
CHAMPION-ASPULLEY-BELT
KIT NO.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 2 Required.
OUTDOOR WET-BULB
10463122041473517050
338381446507
328373439500
10892126001508217364
B90B92B93B95
B96B100B100B101
854867883919
235
7 1/2
11405130571548017719
317363430492
10064118441441016756
347390454513
9671114971410616479
357398461520
9276111531381016214
367406468526
8874108151352015947
378415475532
8006101131294815440
403434489544
753097411265915188
418444496550
701793611236114937
436456504557
8456104671323415694
390424482538
757712792381358347
656923713573477459
5561356347––––
757710781980298239
656819702972397349
5560296239
––––
75777
781579228129
656815692271297237
5559226129––––
11902 / 0 9697 / .5 7347 / 1.02 H.P. MOTOR / CFM-SP*
757713792681398352
656926713973527566
5561396352––––
757711792381348246
656923713472467457
5561346246––––
757710792080298239
656920702972397449
5560296239––––
13626 / 0 11669 / .5 9775 / 1.03 H.P. MOTOR / CFM-SP*
757715793082468461
656930724674617676
5562466461––––
757714792881428355
656928714273557569
5561426355––––
757713792581388350
656925713873507563
5561386350––––
16154 / 0 14468 / .5 12915 / 1.05 H.P. MOTOR / CFM-SP*
757717803482518468
657034725174687785
5562516468
––––
757716803282488464
657032724874647679
5562486464––––
757715793082448459
656930724474597674
5562446459––––
18493 / 0 16996 / .5 15626 / 1.07-1/2 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H.P.,
Q
D
E
E
A
F
G
X
D
S
QD
C
R
C
N
B
A
E E
N
T
W
H
UBPW
J
L
Y
M
J
SAD OUTLETSAD OUTLET
SASOUTLET
TOP VIEW WEIV EDISWEIV TNORF
* All measurements in inches.
D4545
48 1/4
48 1/4
H100W
10012W150W
15012W
WETMODULENUMBER
SAS/SAD 100BSAS/SAD 10012BSAS/SAD 150BSAS/SAD 15012B
BLOWERMODEL
NUMBERCABINET
W44445454
63 3/8
67 3/8
66 5/8
70 5/8
C(SAS)13 19/32
13 19/32
16 13/16
16 13/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
21 3/4
21 3/4
26 7/8
26 7/8
U(SAD)21 11/32
21 11/32
19 5/32
19 5/32
EP(SAD)11 5/8
11 5/8
10 11/16
10 11/16
1 29/32
1 29/32
2 7/32
2 7/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
12 1/2
16 1/2
12 1/2
16 1/2
X
MEDIADIMENSION
Y44 3/4
44 3/4
4848
36 5/8
36 5/8
46 3/8
46 3/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
S
ELECTRICSERVICE
T21 1/2
21 1/2
23 1/8
23 1/8
5 5/32
5 5/32
5 5/32
5 5/32
N4 3/4
4 3/4
4 3/4
4 3/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
42425252
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models SAS/SAD 150 include the affects of an 8 inch thick evaporative media on the inlet. , & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
SASMODEL
BELTSAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
13.8/7.6-6.96.9
3.5-3.2/1.616/8
84.6-4.2/2.120/11-106.6-6/3
5/85/85/85/85/87/87/87/8
11311313
115/208-230230
208-230/460115/230
230208-230/460115/208-230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
12112111
2429202829344140
110455110456110461110457110458
110462-9110459
110463-9
3/43/43/4111
1 1/21 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
24/13.2-127.5-6.8/3.4
10.6-9.6/4.8
7/87/81 1/8
133
115/208-230208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
111
494483
110460110464-9110465-9
223
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8287381287381437437
296390296390446446
278373278373429429
269364269364420420
8350K8450K8350
8450K85508550
B96B96B96B96B96
B100
SASMODEL
BELTB90B90B90B90B90B92
SADMODEL
BELT5/8*5/8*7/8*7/8*
7/81 1/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
3/4, 13/4, 1
11, 1 1/2, 21 1/2, 2
3
253347253347403403
261356261356412412
304398304398454454
313407313407463463
321415321415471471
330424330424480480
338432338432488488
347441347441497497
3DI-1303DI-1353DI-1403DI-1453DI-1553DI-161
SHEAVEBORE
CHAMPION-SADPULLEY-BELT
KIT NO.3DI-1653DI-1703DI-1753DI-1803DI-1853DI-190
CHAMPION-SASPULLEY-BELT
KIT NO.
*When selecting 1 H.P. motor, be sure to select Pulley-Belt Kit with same pulley bore as shaft size of motor selected.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 1 Required.
6203698782059159N/A
298324365399N/A
287314356390N/A
6622737285489476N/A
B90B90B90B90B92
B96B96B96B96B100
584593608612624
3/41
1 1/223
707277838910N/AN/A
275302346N/AN/A
5769660278708855N/A
308333374406N/A
5298619975338555N/A
321343382414N/A
4777576471828244N/A
336355391421N/A
4201528568127924N/A
355369401430N/A
30414231599372369032
402406424448493
25223699553768668741
424427439459500
20403199506764708436
443448456471509
36074764641675929315
378386412438486
7577
7791481218328
656914712173287535
5561216328––––
75775
789
80148218
6568
9701472187323
5560146218
––––
7576
278
579
781
9
6568
569
771
97211
5559
761
9––––
7072 / 0 4777 / .5 2040 /1.03/4 H.P. MOTOR / CFM-SP*
75778
791582238430
656915722374307638
5562236430––––
7577
6791181178222
656911711772227428
5561176222––––
7576
378
779108114
6568
7691071147217
5559106114––––
7783 / 0 5764 / .5 3199 /1.01 H.P. MOTOR / CFM-SP*
75788
801782258434
657017722574347742
5562256434
––––
75777
791481208327
656914712073277534
5561206327
––––
75775
799
80148219
65689
701472197323
5560146219
––––
8910 / 0 7182 / .5 5067 / 1.01-1/2 H.P. MOTOR / CFM-SP*
7577
9801782268434
OUTDOOR WET-BULB657017722674347743
5562266434––––
75778
801582238431
657015722374317639
5562236431––––
75776
791281188324
656912711873247530
5561186324
––––
9476 /.1 8244 / .5 6470 / 1.02 H.P. MOTOR / CFM-SP*
75––––––––
OUTDOOR WET-BULB65––––––––
55––––––––
7577
9801782268434
657017722674347743
5562266434––––
7577
8801582238431
657015722374317639
5562236431––––
9315 / .7 8436 / 1.03 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H.P.
AD OUTLETEE A
Q
XD
G
F
GD
S
QW
R
C
J JN
P
B
B
AL
MME E
N
Y
L
P
D
H
UB
T
AD OUTLET
C
TOP VIEW WEIV EDISWEIV TNORF BLOWERSECTION
AS OUTLET
AU OUTLET
* All measurements in inches.
D4545
48 1/4
48 1/4
60 1/4
H100W
10012W150W
15012W20012W
WETMODULENUMBER
AS/AD 100BAS/AD 10012BAS/AD 150BAS/AD 15012BAS/AD/AU 20012B
BLOWERMODEL
NUMBERCABINET
W44445454
59 1/4
8290
85 1/4
93 1/4
105 1/4
C(AS)13 19/32
13 19/32
16 13/16
16 13/16
18 11/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
U(AD)21 11/32
21 11/32
19 5/32
19 5/32
25 1/4
EP(AU)11 5/8
11 5/8
10 11/16
10 11/16
14 1/4
N/AN/AN/AN/A
24 29/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
30 1/8
12 1/2
16 1/2
12 1/2
16 1/2
16 1/8
X
MEDIADIMENSION
Y44 3/4
44 3/4
484860
36 5/8
36 5/8
46 3/8
46 3/8
51 5/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
18 5/8
S
ELECTRICSERVICE
T39 7/8
43 7/8
41 1/2
45 1/2
51 5/8
5 5/32
5 5/32
5 5/32
5 5/32
5 5/32
N23 1/4
27 1/4
23 1/4
27 1/4
27 1/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
4 3/4
42425252
57 1/4
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP. OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models AS/AD 15012 include the affects of a 12 inch thick evaporative media on the inlet. determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
ASMODEL
BELTAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
24/13.2-127.5-6.8/3.4
10.6-9.6/4.816.7-15.2/7.6
24.2-22/11
7/87/81 1/81 1/81 3/8
13333
115/208-230208-230/460208-230/460208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
11111
49448387121
110460110464-9110465-9110466-9110470-9
2235
7 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8325381381437493
333390390446502
316373373429485
308364364420476
D8400D8450D8450D8550D8600
B96B96B100B100B101
ASMODEL
BELTB90B90B92B93B95
ADMODEL
BELT7/87/8
1 1/81 1/81 3/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
2235
7-1/2
291347347403459
299356356412468
342398398454510
350407407463519
359415415471527
367424424480536
376432432488544
384441441497553
3DI-503DI-523DI-563DI-603DI-65
SHEAVEBORE
CHAMPION-ADPULLEY-BELT
KIT NO.3DI-703DI-723DI-753DI-803DI-86
CHAMPION-ASPULLEY-BELT
KIT NO.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 2 Required.
OUTDOOR WET-BULB
10482122251474917060
324365427484
314356419477
10905126041508417360
B90B92B93B95
B96B100B100B101
967980996
1032
235
7-1/2
11375130201543817672
303346410470
10079118651443416777
335375435491
9678115141413316505
346384443498
9265111651383816242
356393450505
8830108071354015983
368403458512
7867100581289915463
394423474526
732596511264015207
409433482532
675392201232814947
426445490539
8366104401324615724
380413466519
757612772578377949
656725683769497061
5558375949––––
757610772078307940
656720683069407051
5558305940––––
7576
8771577237830
656715672368306938
5557235830
––––
11375 / 0 9265 / .5 6753 / 1.02 H.P. MOTOR / CFM-SP*
757614772878427956
656728684269567070
5558425956––––
757612772478367948
656724683669487060
5558365948––––
757610772078307940
656720683069407050
5558305940––––
13020 / 0 11165 / .5 9220 / 1.03 H.P. MOTOR / CFM-SP*
757616773378498066
656733684970667182
5558496066––––
757615773078457959
656730684569597074
5558455959––––
757613772778407953
656727684069537067
5558405953
––––
15438 / 0 13838 / .5 12328 / 1.05 H.P. MOTOR / CFM-SP*
757617773379508067
656733695070677183
5559506067––––
757617773379528069
656735695270697187
5559526069
––––
757616773278488064
656732684870647180
5558486064––––
17672 / 0 16242 / .5 14947 / 1.07-1/2 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H.P., & Blower Speed are
Q
D
E
E
A
F
G
X
D
S
QD
C
R
C
N
B
A
E E
N
T
W
H
UBPW
J
L
Y
M
J
SAD OUTLETSAD OUTLET
SASOUTLET
TOP VIEW WEIV EDISWEIV TNORF
* All measurements in inches.
D4545
48 1/4
48 1/4
H100W
10012W150W
15012W
WETMODULENUMBER
SAS/SAD 100BSAS/SAD 10012BSAS/SAD 150BSAS/SAD 15012B
BLOWERMODEL
NUMBERCABINET
W44445454
63 3/8
67 3/8
66 5/8
70 5/8
C(SAS)13 19/32
13 19/32
16 13/16
16 13/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
21 3/4
21 3/4
26 7/8
26 7/8
U(SAD)21 11/32
21 11/32
19 5/32
19 5/32
EP(SAD)11 5/8
11 5/8
10 11/16
10 11/16
1 29/32
1 29/32
2 7/32
2 7/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
12 1/2
16 1/2
12 1/2
16 1/2
X
MEDIADIMENSION
Y44 3/4
44 3/4
4848
36 5/8
36 5/8
46 3/8
46 3/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
S
ELECTRICSERVICE
T21 1/2
21 1/2
23 1/8
23 1/8
5 5/32
5 5/32
5 5/32
5 5/32
N4 3/4
4 3/4
4 3/4
4 3/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
42425252
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
2791012 11 6 5 4 3 1
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models SAS/SAD 15012 include the affects of a 12 inch thick evaporative media on the inlet. ., & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMCFM RPMRPMCFMCFM
SASMODEL
BELTSAD
MODELBELT
OPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
13.8/7.6-6.96.9
3.5-3.2/1.616/8
84.6-4.2/2.120/11-106.6-6/3
5/85/85/85/85/87/87/87/8
11311313
115/208-230230
208-230/460115/230
230208-230/460115/208-230208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
12112111
2429202829344140
110455110456110461110457110458
110462-9110459
110463-9
3/43/43/4111
1 1/21 1/2
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
24/13.2-127.5-6.8/3.410.6-9.6/4.8
7/87/81 1/8
133
115/208-230208-230/460208-230/460
H.P.VOLTS
BLOWER MOTORSSPEED
111
494483
110460110464-9110465-9
223
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.0
0.58
8287381287381437437
296390296390446446
278373278373429429
269364269364420420
8350K8450K8350
8450K85508550
B96B96B96B96B96B100
SASMODEL
BELTB90B90B90B90B90B92
SADMODEL
BELT5/8*5/8*7/8*7/8*
7/81 1/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/MOTOR SHEAVE 1/2 TURN DOWN
3/4, 13/4, 1
11, 1 1/2, 21 1/2, 2
3
253347253347403403
261356261356412412
304398304398454454
313407313407463463
321415321415471471
330424330424480480
338432338432488488
347441347441497497
3DI-1303DI-1353DI-1403DI-1453DI-1553DI-161
SHEAVEBORE
CHAMPION-SADPULLEY-BELT
KIT NO.3DI-1653DI-1703DI-1753DI-1803DI-1853DI-190
CHAMPION-SASPULLEY-BELT
KIT NO.
*When selecting 1 H.P. motor, be sure to select Pulley-Belt Kit with same pulley bore as shaft size of motor selected.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water. LAT = Cooler Discharge Temperature.
Pumps - 1 Required.
OUTDOOR WET-BULB OUTDOOR WET-BULB
6087687680919044N/A
289314353386N/A
278303345378N/A
6539728684559375N/A
B90B90B90B90B92
B96B96B96B96B100
645649665669681
3/41
1 1/223
699777028817N/AN/A
267294336N/AN/A
5603645077348719N/A
301324363394N/A
5051599473598389N/A
315336372402N/A
4415547769618043N/A
332349382411N/A
37174893652576839377
353364393420466
24973637552768698751
398404419440482
20133085497664168407
419425435452490
15712609442559328046
436444453465499
30584260605072939070
376383405430474
75768
771578237930
656715682369307038
5558235930––––
7576
4771078147919
65679
681469197024
5558135919––––
7576
276
476
576
7
65664
665
667
679
55565
567––––
6997 / 0 4415 / .5 1571 / 1.03/4 H.P. MOTOR / CFM-SP*
75768
771678258033
656716682570337141
5558256033––––
75766
771278187924
656712681869247030
5558185924––––
75763
766
789
7812
65666
679
68126815
5557
95812
––––
7702 / 0 5477 / .5 2609 / 1.01 H.P. MOTOR / CFM-SP*
75769
771979288037
656719692870377147
5559286037
––––
75767
771578227930
656715682269307037
5558225930
––––
75765
771078157919
656710681569197024
5558155919
––––
8817 / 0 6961 / .5 4425 / 1.01-1/2 H.P. MOTOR / CFM-SP*
757610772079308041
656720693070417151
5559306041
––––
7576
9771778268034
656717682670347143
5558266034––––
75766
771378197926
656713681969267032
5558195926––––
9375 / .1 8043 / .5 5932 / 1.02 H.P. MOTOR / CFM-SP*
75––––––––
65––––––––
55––––––––
757610772079308041
656720693070417151
5559306041
––––
7576
9771778268034
656717682670347143
5558266034––––
9377 / .6 8046 / 1.03 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H.P
AD OUTLETEE A
Q
XD
G
F
GD
S
QW
R
C
J JN
P
B
B
AL
MME E
N
Y
L
P
D
H
UB
T
AD OUTLET
C
TOP VIEW WEIV EDISWEIV TNORF BLOWERSECTION
AS OUTLET
AU OUTLET
* All measurements in inches.
D4545
48 1/4
48 1/4
60 1/4
H100W
10012W150W
15012W20012W
WETMODULENUMBER
AS/AD 100BAS/AD 10012BAS/AD 150BAS/AD 15012BAS/AD/AU 20012B
BLOWERMODEL
NUMBERCABINET
W44445454
59 1/4
8290
85 1/4
93 1/4
105 1/4
C(AS)13 19/32
13 19/32
16 13/16
16 13/16
18 11/16
A
DUCTOPENING
B21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
21 3/4
21 3/4
26 7/8
26 7/8
31 3/4
U(AD)21 11/32
21 11/32
19 5/32
19 5/32
25 1/4
EP(AU)11 5/8
11 5/8
10 11/16
10 11/16
14 1/4
N/AN/AN/AN/A
24 29/32
DUCTLOCATION
F
DRAINLOCATION
G22 1/2
22 1/2
24 1/8
24 1/8
30 1/8
12 1/2
16 1/2
12 1/2
16 1/2
16 1/8
X
MEDIADIMENSION
Y44 3/4
44 3/4
484860
36 5/8
36 5/8
46 3/8
46 3/8
51 5/8
WETMODULE
J18 1/2
22 1/2
18 1/2
22 1/2
22 1/2
L
WATERSERVICE
M5 7/8
5 7/8
5 7/8
5 7/8
5 7/8
14 5/8
18 5/8
14 5/8
18 5/8
18 5/8
S
ELECTRICSERVICE
T39 7/8
43 7/8
41 1/2
45 1/2
51 5/8
5 5/32
5 5/32
5 5/32
5 5/32
5 5/32
N23 1/4
27 1/4
23 1/4
27 1/4
27 1/4
Q
SKIDLOCATIONS
R4 3/4
4 3/4
4 3/4
4 3/4
4 3/4
42425252
57 1/4
DIMENSIONAL DATA*
SIZING TABLES
SHEAVE SELECTION
MOTOR SPECIFICATIONS
SPECIFICATIONS PERFORMANCE Certified Air Delivery At .1" Increments Of External Static Pressure (Inches Static Pressure Water Gauge)
24 1/25 1/267 6 1/2 4 3 1/2 3 2 1/2
OUTDOOR WET-BULB
LATGPHLATGPHLATGPHLATGPH
85
95
105
115
OUTDOORDRY BULB
TEMP.OUTDOOR WET-BULB OUTDOOR WET-BULB
Performance shown is for installation type B - Free inlet, Ducted outlet. Power rating (BHP) does not include drive losses. Models AS/AD/AU 20012 include the affects of a 12 inch thick evaporative media on the inlet. .P., & Blower Speed are determined from the SPECIFICATION table above, use this information to select the proper pulley-belt kit from the SHEAVE SELECTION table below.
RPMAU
BELTB92B92B93B93
CFM RPMRPMCFMCFMAS
BELTAD
BELTOPER.WGT. CFM
MAXB.H.P.
0" 0.1" 0.2" 0.3" 0.4" 0.5" 0.6"RPM CFM RPM CFM RPM CFM RPM RPM
0.8"CFM RPM
0.9"CFM RPM
1.0"CFM RPM
0.7"CFM
9.6/4.815.2/7.6
22/1128/14
1 1/81 1/81 3/81 3/8
3333
230/460230/460230/460230/460
H.P.VOLTS
BLOWER MOTORSSPEED
1111
8387121138
110465-9110466-9110470-9110482-9
35
7 1/210
PHASE MOTORAMPS*
SHAFTDIA.
MOTORWGT(LB)
MOTORPART NO.
*Amperage shown is from National Electrical Code. Use amperage shown on motor nameplate to determine motor protector.
WATTS7377
GPM (5 FT. HEAD)4.64.6
PUMP PART NO.110467110468
VOLTS115230
AMPS1.00.58
5291328392441
300338403450
281319381431
272310369422
D8350D8400D8450D8550
B92B92B93B93
AUMODEL
BELTB112B112B112B112
ASMODEL
BELTB100B100B103B103
ADMODEL
BELT1 1/81 1/81 3/81 3/8
MAUREYSHEAVE
MOTORH.P.
BLOWER RPM/TURNS OPEN OF MOTOR SHEAVE
35
7-1/210
253291347403
262300358412
309347414459
319356425469
328365437478
338375448488
347384459497
3DI-1953DI-2003DI-2033DI-205
3DI-2253DI-2303DI-2333DI-235
ASPULLEY-BELT
KIT NO.SHEAVE
BOREAD
PULLEY-BELTKIT NO.
3DI-2103DI-2153DI-2183DI-220
AUPULLEY-BELT
KIT NO.
* Static Pressure (inches of water). GPH = Water consumption at design conditions but does not include bleed-off amount. Amount of bleed-off will vary with different water sources, but an amount equal to 10% of water consumption at any design condition is considered sufficient for average water.
Pumps - 2 Required.
OUTDOOR WET-BULB
15200183712127023562
292341387423
284334380417
15716188202167023929
B100B100B103B103
B112B112B112B112
1249126412971326
35
7 1/210
16267192862207724301
276327374412
14696179432088823204
300348393429
14190175182051422866
308355399434
13665170922014222528
317361405440
13110166611976922190
325368410445
11886157521901521510
346383422456
11194152721862921171
358390428461
10450147601822920823
371399435467
12521162111939521852
335375416450
757618773678547972
656736685469727090
5558545972609061
107
757615773178467962
656731684669617077
555846596160766091
757612772477367848
656724673568476959
555735584759596071
16267 / 0 13655 / .5 10450 / 1.03 H.P. MOTOR / CFM-SP*
757621774378647985
6567426864698570
106
555863598460
10661
127
757619773878577976
656738685769767095
5558565975609461
113
757617773378507966
656733684969667082
555849596660826198
19286 / 0 17092 / .5 14760 / 1.05 H.P. MOTOR / CFM-SP*
757624774978737997
6567486872699771
121
555872599661
12062
144
757622774578677989
6567446867698970
111
555866598860
11061
133
757620774178617981
6567406861698170
101
555860598060
10061
121
22077 / 0 20142 / .5 18229 / 1.07-1/2 H.P. MOTOR / CFM-SP*
7576277753788079
107
656753688069
10671
133
55587959
10661
13262
159
757625775078747999
6567496874699971
123
555874599861
12362
147
757623774678697992
6567466869699270
115
555868599160
11461
137
24301 / 0 22528 / .5 20823 / 1.010 H.P. MOTOR / CFM-SP*
When the Cooler Model No, Motor H
This warranty is extended to the original purchaser of an evaporative cooler installed and used undernormal conditions. It does not cover damages incurred from accident, neglect, or abuse by the owner. Champion Cooler does not authorize any person or representative to assume for the Corporation anyother or different liability in connection with this product.
TERMS & CONDITIONS OF WARRANTYThis warranty includes lifetime limited coverage on water reservoir against any leakage due to defectsin material. From date of installation, if any original component part provided by Champion Cooler fails due to defect in material or factory workmanship only, Champion Cooler will provide the replacementparts as follows: • Cabinet components for one year from date of installation • Evaporative media for two years from date of installation
EXCLUSIONS TO THIS WARRANTY• Champion Cooler is not responsible for any incidental or consequential damage resulting from any malfunction.• Champion Cooler is not responsible for any damage received from the use of water softeners, chemicals, descaling material, plastic wrap, or if a motor of a higher horsepower than what is shown on the serial plate is used in the unit.• Champion Cooler is not responsible for the cost of service calls to diagnose cause of trouble, or labor charge to repair and/or replace parts.
HOW TO OBTAIN SERVICE UNDER THIS WARRANTYContact the Dealer where you purchased the evaporative cooler. If for any reason you are not satisfiedwith the response from the Dealer, write or call: Customer Service Department, Champion Cooler, 5800 Murray Street, Little Rock, AR 72209, 800-643-8341 or e-mail Champion at: info@championcooler.com.
This limited warranty applies to the original purchaser only.
CHAMPION COOLER certifies that the evaporative air coolers shown here are licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordancewith AMCA Publication 211 and comply with the requirements of the Certified Ratings Program.
The New MasterCool® by Champion Cooler, 5800 Murray, Little Rock, AR 72209 800 643-8341 www.championcooler.com
LIMITED WARRANTY
CSGB -MARCH 2009
Crafted with Pride in the USA