Post on 12-Mar-2020
INDUSTRIAL ACCESSORIES COMPANY
Engineered Solutions for the Cement Industrywww.iac-intl.com
1
Industrial Accessories Company is an industrial design/build and original equipment manufacturer of baghouses, flue gas desulfurization, heavy metal mitigating sorbent injection systems, dry bulk materials handling, and pneumatic conveying systems
PP030
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – IAC Provides APC compliment to newest USA plantwww.iac-intl.com
2
Drake Cement, LLC, located in Drake, Arizona, is one of the Southwest U.S.’ newest cement plants.
Drake focuses exclusively on the production of Type II/V (LA) Portland cement
Medium to high volatile coal is used as primary fuel
IAC provided 34 baghouses, air-to-air heater exchanger, screw conveyors, rotary valves, fans, dampers, and custom steel fabrication for the project
Drake Cement – IAC Provides APC compliment to newest USA plantwww.iac-intl.com
3
The plant includes a six stage precalciner/preheaterkiln with a rated capacity of 660,000 tons of clinker per year or 2,000 tons per day
Drake Cement – IAC Provides APC compliment to newest USA plantwww.iac-intl.com
4
Drake Cement must conform to very stringent emission limits. IAC provided Drake with guarantees to meet these limits
Drake Cement – IAC provided Clinker Cooler Baghouse and Stackwww.iac-intl.com
5
Several operating and pollution controls incorporated into the
plant are so advanced that they are found in only a few other
facilities throughout the world
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 1: Overland Conveyors from Quarry to Plantwww.iac-intl.com
6
Three overland conveyors with a total length of 3500 ft. transport limestone from the quarry to the plant. IAC provided Jet Pulse Filters at the discharges of the Primary Crusher and each of the three overland conveyors
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 1: Overland Conveyor termination Baghousewww.iac-intl.com
7
The raw material consists of 72% High Limestone and 26% Low Limestone materials mined from the Drake quarry. There is a 17 day covered storage reserve equivalent to approximately 51,000 tons
Drake Cement – Department 2: Transportation to Raw Material Siloswww.iac-intl.com
8
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 2: Transportation to Raw Material Siloswww.iac-intl.com
9
IAC provided Jet Pulse fabric filters to control dust at belt conveyor discharges and raw material and coal silos.
Eight 6 m bolted steel silos store High and Low limestone, iron ore, gypsum, clinker, Bauxite and raw coal
Drake Cement – Department 3: Raw Material, Coal and Gypsum Siloswww.iac-intl.com
10
Drake Cement – Department 3: Baghouses atop Raw Material Siloswww.iac-intl.com
11
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 3: Baghouses atop Raw Material Siloswww.iac-intl.com
12
IAC provided a total of 31 dust handling and nuisance dust filters on the project. Each had 8 ft. long bags
All were designed with 70 degree hoppers and were factory insulated to promote discharge of material, avoiding condensation effects due to dramatic shifts in the nighttime and daytime desert temperatures
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 4: Railroad and Truck Discharge Installationwww.iac-intl.com
13
Drake Cement has a railroad and truck discharge system to unload limestone from outside sources, as well as other raw materials and coal sourced from Colorado and neighboring Western states
The plant has a 32 day reserve of clinker storage which includes a covered clinker dome of 50,000 tons and an emergency stock silo of 13,800 tons
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 4: Railroad and Truck Discharge Installationwww.iac-intl.com
14
Shown are IAC Jet Pulse filters for collecting dust during transfer and discharge from the belt conveyors transporting raw coal, iron ore and Bauxite from Raw Material Receiving and for the discharge of Limestone and Raw Materials from covered stockpile to blending silos
Drake Cement – Department 5: Raw Material Grindingwww.iac-intl.com
15
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 5: Raw Material Grindingwww.iac-intl.com
16
A Raw Meal Grinding System with an output of 171 ton/hr includes high-pressure Roller Press, combined with a High Efficiency Separator configuration. Hot gases used in the crusher for drying are taken from the six stage Preheater of the kiln
IAC supplied the four 2.8 m de-dusting cyclones as primary dust collection for the Raw Mill and Crusher
IAC supplied its M-Pulse Jet Pulse baghouse for the final collection from the Raw Mill and the Kiln
Drake Cement – Department 5: Raw Mill / Kiln Baghousewww.iac-intl.com
17
Major M-Pulse baghouse product features include:
• Low 50 psi pulse pressure for gentle bag cleaning
• Unique inlet gas baffle plate design, which aids in particle collection before filter media is encountered and in gas flow distribution in each module
• Simplified service through easily accessed cleaning valves and controls
• Penthouse enclosure provides weather protection for baghouse maintenance with overhead electric hoist on monorail for lifting insulated module roof doors for ease of bag removal
• Long bag design, (6 and 7 meter), reducing equipment footprint and capital investment for customer
• Steep pyramidal hopper design for each module, which aids material flow and simplifies material collection
• Individual and separated inlet and outlet gas manifolds to promote even gas flow distribution into and out of each cleaning module
• Automation integration into centralized plant system control
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 5: Raw Mill / Kiln Baghousewww.iac-intl.com
18
Combined gas flow is 350,000 Actual cubic meter/hr at 250 F from the Raw Mill and the Kiln supplied to the IAC M-Pulse baghouse for final collection
After passing through the baghouse I.D. fan, the gases are directed to a 2 m diameter x 65 m tall stack provided by IAC
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 5: Raw Mill / Kiln Baghousewww.iac-intl.com
19
Steep pyramidal hopper design for each module aids material flow and simplifies material collection. Each hopper is equipped with a rotary airlock valve. Each hopper is insulated to prevent cooling and condensation of moisture inside the hopper
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 5: Raw Mill / Kiln Baghousewww.iac-intl.com
20
Steep M-Pulse pyramidal hopper design for each module aids material flow and simplifies material collection
Each is equipped with level detection, poke-hole, cut-off gate and rotary airlock valve suitable for high temperature service equipped with rotation detector
Drake Cement – Department 6: Blending Silowww.iac-intl.com
21
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 6: Blending Silowww.iac-intl.com
22
There is a three day storage reserve of raw meal held in the 9,000
ton blending and storage silo
The silo has a homogenizing
chamber which permits a continuous blending
of the raw meal simultaneously to the
silo feeding and discharge
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 7: Kiln Feedwww.iac-intl.com
23
The Raw Meal Feeding System for the Preheaterincludes airslides, weighing bin with load cells, flow meter and two high belt bucket elevators (one as a standby) with a design capacity of 170 ton/hr
IAC provided much of the ductwork, access towers and support steel for the Preheater for the kiln
Drake Cement – Department 8: Six Stage Preheater with Calcinerwww.iac-intl.com
24
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 8: Six Stage Preheater with Calcinerwww.iac-intl.com
25
The kiln is connected to a six stage Preheater Tower including a “state-of-the-art” low NOx Internal Line Calciner (ILC) working together with selective non-catalytic reduction (SCNR) for NOx reduction
The Preheater Tower takes most of its combustion air from the kiln hood through a tertiary air duct
Fuel consumption is 50-55% in the calciner and 45-50% in the kiln burner
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 9: Rotary Kilnwww.iac-intl.com
26
The rotary kiln is 3.81 m dia. x 45.7 m long,
supported on 2 bases
A Clinker Cooler with air beam technology is
employed for the 2000 ton/day production rate
The gases leaving the Cooler, going to the baghouse first pass
through an Air-to-Air Heat Exchanger provided by IAC
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 10: Cooler Heat Exchanger and Baghousewww.iac-intl.com
27
The Air-to-Air Heat Exchanger cools the hot clinker cooler vent gas prior to entering the dust collector and the vent fan
During upsets, the Air-to-Air Heat Exchanger aids to protect the downstream equipment so that it stays within design temperature limits
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 10: Air-to-Air Heat Exchangerwww.iac-intl.com
28
The tubes are shop welded to upper and lower tube sheets, with intermediate tube guides located between fan levels to guide the tubes. The lower tube sheet is welded to the frame, while the inlets of the tubes float to allow for thermal expansion
The dust that drops out of the gas stream passing through the Air-to-Air Heat Exchanger is collected in a bottom hopper and transported out by a screw conveyor. At the discharge of the screw conveyor, a rotary valve minimizes false air intake before passing the dust to the subsequent conveying system
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 10: Air-to-Air Heat Exchangerwww.iac-intl.com
29
The exhaust gas from the clinker cooler is vented to the Air-to-Air Heat Exchanger where it passes evenly through vertical parallel tubes. Cooling is accomplished by forced convection from cross-flow fans (not shown) moving ambient air over the outer surface of the tubes
The Air-to-Air Heat Exchanger reduces the temperature of the clinker cooler gas venting to the dust collecting system, thereby lowering the gas volume to be handled and fan horsepower requirements
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 10: Clinker Cooler Baghouse and Stackwww.iac-intl.com
30
IAC's M-Pulse, long bag, medium pulse pressure baghouse is designed for efficient operation and effective cleaning for this large process gas flow application of 167,000 cubic meters per hour
The M-Pulse baghouseis effective for both high dust loading and high temperature service
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 10: Clinker Cooler Baghouse and Stackwww.iac-intl.com
31
IAC supplied both the raw mill/kiln exhaust stack and the Clinker Cooler exhaust stack. Both were equipped with multiple access levels to allow ease of maintenance of the CEMS and for safety during stack testing
Raw Mill/Kiln Stack: 2 m dia. X 65 m tall
Clinker Cooler Stack: 1.9 m dia. X 65 m tall
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 11: Cooler Discharge Baghousewww.iac-intl.com
32
IAC provided a total of 31 dust handling and
nuisance dust filters on the project. Each had 8 ft.
long bags
All were designed with 70 degree hoppers and were
factory insulated to promote discharge of
material, avoiding condensation effects due
to dramatic shifts in the nighttime and daytime
desert temperatures
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 11: Clinker Transport to Clinker Domewww.iac-intl.com
33
The clinker discharged from the Cooler is transported towards the clinker dome with a hot pan conveyor which discharges the clinker either to the dome central tower or to a side belt conveyor which travels towards the emergency clinker silo
Drake Cement – Department 11: Clinker Storage Dome and Emergency Silowww.iac-intl.com
34
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 11: Clinker Transport to Grindingwww.iac-intl.com
35
In order to feed the cement grinding department with
clinker, an underground belt
conveyor collects the clinker from either the
dome or from the clinker silo
This belt feeds a second belt conveyor
towards the clinker silos which supply
clinker and gypsum to the cement grinding
department
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 12: Coal Grinding and Pneumatic Baghouseswww.iac-intl.com
36
Coal is pulverized by a Vertical Mill with a capacity of 15 tons per hour. The emissions control for the mill includes an IAC Jet Pulse filter equipped with explosion relief panels. The baghouse has a “walk-in” plenum, is structurally reinforced and insulated
Drake Cement – Department 12: Coal Grinding Baghousewww.iac-intl.com
37
Drake Cement – Department 13: Cement Grindingwww.iac-intl.com
38
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 13: Cement Grindingwww.iac-intl.com
39
The plant includes a “Combined Grinding”system consisting of a Roller Press in close circuit with a High Efficiency Separator, Dissaglomerator and Bucket Elevator to produce 100 tons per hour before being fed to a 2500 hp Ball Mill
Drake Cement – Department 13: Cement Grinding Baghouseswww.iac-intl.com
40
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 14: Cement Transport to Cement Silowww.iac-intl.com
41
A bucket elevator feeds the Cement Silo at a design rate of 180
ton/hr
The silo has a mixing silo process discharge
An IAC baghouseprovides dust capture
from the silo mixing air introduced into the silo
INDUSTRIAL ACCESSORIES COMPANY
Drake Cement – Department 14: Cement Silo and Baghousewww.iac-intl.com
42
A 10,000 ton storage Cement Silo provides a five day cement stock reserve for the plant
A Pneumatic Parallel Distributor with four discharge spouts then feeds the Silo
IAC provided the dust filter to collect the dust and discharges it into the Silo
INDUSTRIAL ACCESSORIES
COMPANY
Drake Cement – Department 14: Cement Loading to Trucks and Railcarswww.iac-intl.com
43
Cement dispatch can be done simultaneously to two bulk trucks and to one bulk railcar at the same time
An IAC baghouse atop the structure provides dust capture from the bucket elevator, airslide conveyor and silo discharge spouts
INDUSTRIAL ACCESSORIES COMPANY Products and Systems:
• OEM Baghouse and Pneumatic Conveyor Supplier• Technology for SOx, HCl and Hg Removal• Fly-ash & Dry Bulk Pneumatic Conveying Systems• Dry Bulk and Liquid Storage Tanks• Biomass Raw Material Storage and Distribution Facilities• Coal and Biomass Steam Generation for Heat and Power• Process Controls• Field Construction and Project Management• Engineering and Design Services• Assistance for Air Quality Permitting• On-site Sorbent Injection and Compliance Services• Annual or Semi-annual Inspection Services
www.iac-intl.com44
INDUSTRIAL ACCESSORIES COMPANY Project Execution:• Plant General Equipment and Facility Arrangement• Plant Process and Equipment Requirements Determination• Emission Compliance Requirements Determination• Project Scheduling, Procurement and Delivery Management• Engineering and Design• Fuel and Ash Handling Equipment Supply• APC and Combustion Equipment Supply• Construction Activities, Rentals and On-site Management• Mechanical Millwrights• Pipe Fitters• ASME Welders• Crane Operators• OSHA and MSHA Trained Field Staff• Engineering and Start-up Assistance
www.iac-intl.com45
THANK YOUINDUSTRIAL ACCESSORIES COMPANY
4800 LAMAR AVENUE
MISSION, KANSAS 66202
800.334.7431 or 913.384.5511
Email: iaccorp@iac-intl.com
www.iac-intl.com46