Post on 25-Jul-2022
GLASS RAILINGAluminum Extrusions
- Designed for interior and exterior Railing Applications
- Tempered laminated glass with Sentryglas Interlayer
- Supports Surface Mount, Embed Mount, Inclined and Fascia Mounting Methods
- Fast and simple installation. Reduces Installation Labor Time by 50%
Copyright©-Product patented by Aluwind S.A
GLASS RAILING
aluwindus.com
K1-NOA #20-1021.03
TOP OF SLAB OPTIONS
Use proper glazing
Use proper glazing Use proper glazing Use proper glazing
Use proper glazing Use proper glazing
Aluminum Extrusions
Copyright©-Product patented by Aluwind S.A
Top mount base shoe (max. panel height 43”)
Top mount base shoe (max. panel height 43”)
LED housing
KIT: K1
Curved base shoe
KIT: K3
KIT: K4
LED housingKIT: K5
K1 UP TO 771lb (350Kg.)
K4 UP TO220lb (100Kg.)
Glass fence(max. panel height 118”)
KIT: K11 KIT: K14
KIT: K15
Top mount base shoe (max. panel height 59”)
K11 UP TO 1984lb (900Kg.)
K14 UP TO 1433lb (650Kg.)
K15 UP TO 1984lb (900Kg.)
Continuous and modular base shoe
Continuous and modular base shoe Continuous and modular base shoe
Continuous base shoe
Continuous base shoe
ExteriorInterior
F-Shaped Floor Mount(max. panel height 19”)Continuous base shoe
KIT: K16
K16 UP TO330lb (150Kg.)
4.72
” (1
20m
m)
2.6”(66.5mm)
3.18”(81mm)
3.92
”(99
.8m
m)
5.22
”(13
2.8m
m)
2.94”(74.8mm)
7.74
”(19
6.7m
m)
5.39”(137mm)
4.84
”(12
3mm
)
5.39”(137mm)
3.99”(101.5mm)
4.06
”(10
3.3m
m)
6063 AlloyT6 Temper
MODULE OPTIONS
Use proper glazing Use proper glazing
Use proper glazing Use proper glazing
Aluminum Extrusions
Copyright©-Product patented by Aluwind S.A
1.89”(48mm)
4.4
4”(1
13m
m)
Continuous and modular base shoe
Continuous base shoe Continuous base shoe
Continuous base shoe
Opciones FRENTE LOSA
HANDRAIL OPTIONS
LED Handrail
Square Handrail
Round Handrail
KIT: K7
KIT: K8
KIT: K9
Embedded in slab (max. panel height 43”)
KIT: K6
K6 UP TO 1322lb (600Kg.)
Fascia Mountmax. panel height 43”
Fascia Mountmax. panel height 43”
KIT: K12
K12 UP TO 1212lb (550Kg.)
Embedded in slab(max. panel height 19”)
KIT: K10
K10 UO TO330lb (150Kg.)
KIT: K17
K17 UP TO 330lb (150Kg.)
1.92”(48.9mm)
3.73
”(94
.9m
m)
2.90”(73.7mm)
5.35
”(13
6mm
)
5.23
”(13
3mm
)
2.16”(55mm)
1.49”(38mm)
2.28”(58mm)
1.69
”(43
mm
)1.
65”(
42m
m)
1.90
”(48
.3m
m)
2.92”(74.3mm)
6063 AlloyT6 Temper
Glass railingImperia
Aluminum Extrusions
Copyright©-Product patented by Aluwind S.A
ANG1
SPA1
1 to hold the handrail end against the wall
We recommend spacing theBrackets 39 inches apart
We recommend spacing theBrackets 39 inches apart
RLED LED String 5630 / 600 1,2A/m
ALUWIND
ALUWIND
ALUWIND
ALUWIND
ALUWIND
ALUWIND
ALUWIND
TRAN12v power adapter [1-5]Amper
ampere per meter
1[m]_____1[A] 2[m]_____2[A] 5[m]_____5[A]
SCL1
VID
INS
Silicone weather- proofing sealant
DOW CORNING 791
VIDRIOS CON SENTRYGLAS
INSTALACION
1
SKU DESCRIPTION SUPPLIER IMAGE QTY Unit Usage
1 Piece
1
Insert one per joint
Insert one per joint
Insert one per glasscorner joint
Insert one per glass linear joint
Insert one per glasscorner joint
Insert one per glass linear joint
1
Stainless steel angle
Stainless steel handrail bracket
ASP1 ALUWIND 1Stainless steel glass connector with handrail bracket
ESK9 K7/K9 aluminum corner joint
1
1
All along the handrail/led housing
1
1
Strip
HERR
GRAMPA DE AMURE GAK6 ALUWIND
Chock spatule
Stainless steel U folded channel for 10 mm-21mm tempered glass
1
1
9010/9012/9016/9020
AR10/AR12/AR16/AR20
Stainless steel 90° (folded) glass connector for 10mm-21mm tempered glass
ALUWIND 1YM16 YM16 glass connector (180°)
YM15 YM15 glass connector (90°)
ALUWIND
-
-
-
1ESK1 K1 / K8 aluminum corner joint
SPR1 We recommend spacing theBrackets 39 inches apart
ALUWIND 1Stainless steel squared wall bracket
ACCESSORIES
AI01 User-defined
User-defined
User-defined
User-defined
User-defined
User-defined
ALUWIND 1Suplemento de alto impacto 3mm
ADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
PieceADDITIONAL ACCESSORY
Glass railingImperia
Aluminum Extrusions
Copyright©-Product patented by Aluwind S.A
1
1TK04
TK01
K4 stainless steel end cap
Piece1
1 placed at the endof the profile.Used for aesthetic finish
K1 plastic end cap
K1+K3 stainless steel end cap
K6 stainless steel end cap with hose fitting
K6 stainless steel end capwith hose elbow
K5 stainless steel end capTK05
TK08
TK03
1
1
1K7 plastic end cap
K8 plastic end cap
K9 stainless steel end cap
TK07
SKU DESCRIPTION SUPPLIER IMAGE QTY Unit Usage
ALUWIND
ALUWIND
ALUWIND
ALUWIND
ALUWIND
ALUWIND
TK6R 1ALUWIND
TK6R 1ALUWIND
TK09 1ALUWIND
ACCESSORIES
K1+K3 (on both sides)stainless steel end capTK33 1ALUWIND
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Piece
Piece
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
1 placed at the endof the profile.Used for aesthetic finish
ADDITIONAL ACCESSORY
Glass railingImperia
Aluminum Extrusions
Copyright©-Product patented by Aluwind S.A
R010
R100
HDM5
R500
HITC
KHEZ
SIW2
CBAT
B22V
SKU DESCRIPTION SUPPLIER IMAGE Unit Usage
SKU DESCRIPTION SUPPLIER IMAGE Unit Usage
ACCESSORIES
ACCESSORIES
User-defined
User-defined
User-defined
User-defined
User-defined
User-defined
CHEMICAL ANCHOR
50pc100pcKH-EZ
(418059)
Screw anchor kh-ez(cod.418059) 3/8”x4”
SIW 22T-A 1/2"(405032)
Impact wrench 22v siw22T-A 1/2"(cod.405032)
B 22/5.2(2136396)
Compact 22v Battery pack (cod.2136396)
C 4/36-90 2026282
Multi-voltage compact charger for all Hilti Li-ion batteries (cod.2026282)
SCREW ANCHOR
HILTI USA
HILTI USA
HILTI USA
HILTI USA
HILTI USA
HILTI USA
HILTI USA
HILTI USA
HILTI USA
19.61 fl ozADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
ADDITIONAL ACCESSORY
RE-10(2142303)
Re-10 anchoring system (cod.2142303)injectable epoxy mortar for anchoring in concrete
Inject the anchor before inserting the threaded rod
Inject the anchor before inserting the threaded rod
Inject the anchor before inserting the threaded rod
11.16fl oz16.91 oz
RE-100(2123384)
Re-100 anchoring system (cod.2123384) High-performance injectable epoxy mortar
** Requires HIT-CB500 cartridge holdernot included.
** Requires HIT-CB500 cartridge holdernot included.
1x Paquete de lámina doble1x Mezclador
RE-500(2123404)
Re-500 anchoring system (cod.2123404)
Resina epóxico, alto rendimiento para conexiones barras/anclajes de altas cargas
Piece
Piece
Piece
Piece
HDM 500 (2005641)
Manual anchor adhesive dispenser hdm-500 (cod.2005641)
1 dispenser
1 cartridge holder
HDM 500 +HIT-CB
(3560133)
Manual dispenser with cartridge holder Hit-cb (COD.3560133)
RE-100RE-500
Glass railingImperia
TOP MOUNT BASE SHOE
4" M
IN. E
MB
EDM
ENT
AW 1001 Aluminum handrail
Plastic diffuser
Led strip
Stainless steel alignment bolt
Interior glazinggasket
Dow Corning Silicone
ABS chock
Plastic diffuser
Led strip
AW1003Mount aluminumLED profile housing
Dow Corning Silicone
Exterior
EXTERIOR
gasket
L Settingblock
AW 9100Base shoe
3/8" Stainless steelThreaded rod
3/8" Stainless steel
Rubber washer
Washer
3/8" Stainless steelNut
Hilti chemicalanchoring system
5mm Stainless steelalignment bolt
Dow Corning Silicone
Water drainage
Aluminium joint Corners
Rubber gasket
Aluminum Extrusions
* Optional mechanical anchor KH-EZMechanical anchors do not guaran-tee water tightness.It is recommended to use a rubber washer and seal the profile sides.5" MIN. EDGE DISTANCE
44”
(110
0mm
) MAX
.RA
ILIN
G H
EIG
HT
4.72
” (1
20m
m)
1.89”(48.2mm)
CONTINUOUS BASE SHOE100% of the glass width mustbe contained in the profile
NOT SUITABLE FOR MODULAR USE
0.060”(1.52mm) Sentryglas
Interlayer
1/4”(6mm)- 5/16”(8mm)- 3/8”(10mm) HEAT STRENGTHENED GLASS
FBC
TAS 201-94
TAS 202-94ANSI Z97.1
(Florida Builing Code 2020)K1-NOA #20-1021.03
Glass railingImperia
1- Place the profile and mark the concrete surface
*Align the Base Shoe and previously mark the required holes using Ø6mm drill bitin the concrete before drilling
Aluminum Extrusions
2-Drill 9cm into concrete slab and clean the dust
3.Inject chemical anchor
90
45
15
140
WARNING!
250
250
12
Drill bit must be buried minimum 90mm into slab. Take account of the floor binder as well as the profile thickness.
It is MANDATORY to clean the dust from the slab-holes before injecting the chemical anchor/ inserting the mechanichal anchor
It is VERY IMPORTANT to place the base shoe before inserting the threaded rod for proper alignment
Set Base Shoe in place, making sure the Base Shoe holes match the slab holes
3. Insert threaded rod
1. Inject chemical anchor
2. Place base shoe
CHECK THE PROFILE IS PERFECTLY LEVELLED otherwise the glass won’tbe perfectly vertical
VERY IMPORTANT!LEVEL THE SURFACE
Drill Ø12mm holes for threaded rod and chemical anchorDrill Ø10mm holes for mechanical anchor
Glass railingImperia
100
3/8” Nut
3/8” Washer
6- Tighten nuts and washers
5- Place all L setting blocks into the base shoecavity.
Note: Tighten until achieving6Kn of torque in a dried and cleancondition
14mm Socket wrench
Note: L gaskets must beplaced between anchoringsystem bolts.
250
Aluminum Extrusions
VERY IMPORTANT!The profile must always be in full contact with the surface
Glass railingImperia
Metal spatule
90°
Roll in exterior gasket
Put the glass above L setting Block
Roll in the Interior GlazinggasketPush the chock
into the profile’s cavity
250mm spacingbetween chocks
6- Glass Panel Installation
7- Plastic chocks installation
8- Use Installation/Removal Tool (spatule) to lock the glass securely in place
Make sure the glass is plumb and perfectly aligned with adjacent panels
Warning: keep the tool separeted fromthe glass when installing the chocks
Before installing the glass panels the L-Setting Blocks must be adhered onto the bottom of the base shoe
Aluminum Extrusions
Each chock must be placed right in front of an L
Glass railingImperia
Aluminum Extrusions
code 2749 (8+8mm)
Interior glazing gasket (varies)
code 2753(10+10mm)
AW D01Led profile housing
AW D04Top column
exterior rubber gasket
code 2821
Exterior glazinggasket code 2053
Diffuser
Chemicalanchoring
system
AW D02Bottom cover
3/8" stainlesssteel threaded rod3/8" stainless steelnut
3/8" stainless steelwasher.
AW D03Base shoe
Heat strenghtenedglass8+8/ 10+10
Sentryglasinterlayerde 0.89mm
ABS chock
LED
L settingblock
Screw M5X20mm
K11- GLASS FENCE7.
75” (
197m
m)
5.39” (137mm)3.54”(90mm)
Glass railingImperia
Aluminum Extrusions
Chemical anchoringsystem
3/8" stainlesssteel threaded rod
3/8" stainless steelnut
3/8" stainless steelwasher.
L settingblock
0.060”(1.52mm)
SentryglasInterlayer
1/4”(6mm)- 5/16”(8mm)- 3/8”(10mm)HEAT STRENGTHENED GLASS
Exterior glazinggasket code 2921
K12- FASCIA MOUNT
Interior rubber gasket (varies)
AW D07- U Channel
11x50 Angle
Plastic chock
AW D05Base shoe
AWD06 cover
2.91” (74mm.)
5.35
” (13
6mm
.)
3.54” (90mm.)
Glass railingImperia
Aluminum Extrusions
K12- Fascia Mount
Modular system (optional)
*module length 9.87” (250mm) or 19.68”(500mm)
500
250
250
250
Continuous
1/4”(6mm)- 5/16”(8mm)-3/8”(10mm)HEAT STRENGTHENED GLASS
Interior rubber gasket (varies)
Glass railingImperia
Aluminum Extrusions
4" (900mm)MIN. EMBEDMENT
ABS chockExteriorgasket
L Settingblock
3/8" Stainless steelThreaded rod
3/8" Stainless steelRubber washer
3/8" stainless steelwasher.
3/8" Stainless steel
3/8" stainless steelnut
Hilti chemicalanchoring system
5" MIN. EDGE DISTANCE
59”
(150
0mm
) MAX
.RA
ILIN
G H
EIG
HT
5.23
” (1
33m
m)
2.83”(72mm)
AW 1016Base shoe
AW 1017cover
K15- Top Mount base shoe(max. panel height 59”)
Exterior glazinggasket code 2921
Glass railingImperia
Aluminum Extrusions
Modular system (optional)
*module length 9.87” (250mm) or 19.68”(500mm)
Continuous
K15- SISTEMA SOBRE LOSA
500
250
250
250
Extruded Aluminum Glass railingImperia
Interior glazinggasket
Exterior gasket
L Setting
block
0.060”(1.52mm) Sentryglas
Interlayer
1122 Angle
Removeafter pouring the concrete slab
5" (110mm)
1.89”(48mm)
Rubber T gasket prevents the entry ofconcrete mix(optional)
2.16”(55mm)1.
69”(4
3mm
)Stainless steel alignment bolt
Aluminum joint
Handrail gasketAW1001LED Handrail
1/4”(6mm)- 5/16”(8mm)- 3/8”(10mm)HEAT STRENGTHENED GLASS
4.4
4”(1
13m
m) Plastic chock
AW1008 hidden base
Aluminumanchor
porcelain tile
5”MIN. EDGE DISTANCE (110mm)
HIDDEN BASE CHANNEL
CONTINUOUS BASE SHOE100% of the glass width mustbe contained in the profile
NOT SUITABLE FOR MODULAR USE
Extruded Aluminum Glass railingImperia
Water drainage
Drain connectionto ø14mm hose
Drain channel
Paste with transparent silicone sealant
Joint gap
Anchor point
Embedded aluminiumanchor
End cap with hose Elbow
End cap with hose fitting
Optional
Glass railingImperia
Aluminum Extrusions
LED SQUARE
KIT: K7 KIT: K8
ROUND
KIT: K9
Handrail installing
HANDRAIL systems
EPDM RUBBERGASKET
ALUMINUM HAND RAIL (K7/ K8/ K9)
*First place the rubber gasket on top of the glass and then press the aluminum profile over it.
**With 8+8 and 10+10 glazing, place the rubber gasket inside the aluminum profile and then press them over the glass.
55
EPDMgasket
Alignmentbolt
AW1001
10 to 21mmglazing
Attention! A little pressure is needed to push the handrail in its place.
10 mm heat’n strenghtened glass with Sentryglas interlayer 0.89mm (6+6 / 8+8 / 10+10)
Glass railingImperia
Aluminum Extrusions
2”(51mm)
2” (51mm) 1.33” (34 mm)
1.33” (34 mm)
3.9” (100mm) 3.9” (100mm)
3.9” (100mm)
3.9” (100mm)Material: Aluminum
thickness 0.11”(3mm)
Material: Aluminumthickness 0.11”(3mm)
Square HandrailLED HandrailRound Handrail
KIT: K7 KIT: K8KIT: K9
45º Mitered Handrail
Aluminum L Shape Connector
Aluminio Extruido
ALUWIND SAAv. Japón 550 C.P. X5019BGZ
Córdoba, Argen�naaluwindus.com
GLASS RAILING
Aluminum Extrusions