Post on 03-Jun-2018
8/12/2019 Hydraulics power System
1/20
1
TSM 363 Fluid Power Systems
Hydrostatic Transmission
8/12/2019 Hydraulics power System
2/20
TSM 363, Lect 10
2
Hydrostatic Transmission is popularin ORE
8/12/2019 Hydraulics power System
3/20
TSM 363, Lect 10
3
Mechanical Drivetrain
A mechanical drivetrain systemconsists of an engine, a clutch,a transmission, a universal drive-line, a differential, and the wheels.
Transmission is used to increaseor decrease speed
A differential is needed in
mechanical drivetrain, becauseit allows the outside wheel torotate faster than in the insidewheel when the vehicle turns.
8/12/2019 Hydraulics power System
4/20
TSM 363, Lect 10
4
Hydrostatic Transmission DrivetrainWith a hydrostatic transmission, itconsists of an engine, a clutch,a hydrostatic transmission, auniversal driveline, a differential,and the wheels.Change the displacement of thepump (or motor) can change thevehicle speed.
HT improves maneuverability:> wide range of T/n ratio> compacted, less mass inertia> dynamic braking (inst. reverse)> able to stall & undamaged> no interruption of power
HT has lower efficiency
8/12/2019 Hydraulics power System
5/20
TSM 363, Lect 10
5
Basic Concept ofHydrostatic Transmission
A hydrostatic transmission is simply a pump and motor(s)connected in a circuit.
8/12/2019 Hydraulics power System
6/20
TSM 363, Lect 10
6
Basic Types of HST
8/12/2019 Hydraulics power System
7/20
TSM 363, Lect 10
7
(a) Fixed pump-fixed motor
(d) Variable pump-variable motor
(b) Variable pump-fixed motor
(c) Fixed pump-variable motor
Typical Closed-Circuit HST Configurations
8/12/2019 Hydraulics power System
8/20
TSM 363, Lect 10
8
Typical P erformance of VP-FM HST
8/12/2019 Hydraulics power System
9/20
TSM 363, Lect 10
9
Typical P erformance of FP-VM HST
8/12/2019 Hydraulics power System
10/20
TSM 363, Lect 10
10
Typical P erformance of VP-VM HST
8/12/2019 Hydraulics power System
11/20
TSM 363, Lect 10
11
Typical HST Releasing & Recharging
8/12/2019 Hydraulics power System
12/20
TSM 363, Lect 10
12
Typical Controls of Closed-Circuit HSP
8/12/2019 Hydraulics power System
13/20
TSM 363, Lect 10
13
Typical Open-Circuit HST Configurations
(b) Four-way valve controlledfixed pump-fixed motor
(a) Needle valve controlledfixed pump-fixed motor
8/12/2019 Hydraulics power System
14/20
TSM 363, Lect 10
14
Typical E/H Controlled Open-Circuit HSP
8/12/2019 Hydraulics power System
15/20
TSM 363, Lect 10
15
Typical HST Arrangement - 1
8/12/2019 Hydraulics power System
16/20
TSM 363, Lect 10
16
Typical HST Arrangement - 2
8/12/2019 Hydraulics power System
17/20
TSM 363, Lect 10
17
Typical HST Arrangement - 3
TSM 363 L 10
8/12/2019 Hydraulics power System
18/20
TSM 363, Lect 10
18
Example:Typical Calculations of HST
Suppose both the pump and the motor in a hydrostatictransmission have disp. D M = 1.925 in3/rev, and the volumetricefficiency are 0.90 for both the pump and motor. The pumpis driven by an engine at 2400 rpm, what is the motor speed?
Theoretical flowQ t = (DPnE)/231
= (1.925x2400)/231 = 20 gpmPump flow
QP = Qt Eff P = 20x0.90 = 18 gpmMotor speednM = (QP231)/ D M Eff M
= (18X231)/1.925x0.90 = 1944 rpm
TSM 363 L 10
8/12/2019 Hydraulics power System
19/20
TSM 363, Lect 10
19
A Special HST Application
TSM 363 L t 10
8/12/2019 Hydraulics power System
20/20
TSM 363, Lect 10
20
Lecture Summary
Discussed the basic concepts of HST: Closed-circuit HST: FP-FM; VP-FM; FP-VM; VP-VM
Open-circuit HSTApplications of HST:
In-line designSprit designV-controlled designSprit-torque design