Post on 28-Oct-2021
PROF. PAUL C. KING RA
New York City College of Technology
Fall 2011
LC.1200-1290 Tutorials.03 Bldg.Gym- Prof.King V.1.0.docx
Copyright © 2011 Paul C. King
Gym.Truss.2 UPDATING LINKED
Overview: Working with an existing flat roof and truss update the roof and truss from a flat
profile to a peaked profile.
Before we begin we will make several quick changes to the building. We will
replace the roof and parapet configuration for a roof that will ove
the face of the building, we will remove the stone coping from the top of the
wall and we will attach the top of the wall to underside of the roof.
Modify the Wall: Select the exterior wall and then select "
version of the wall with the coping stone then "
Attach Wall to Roof Select all four (4) gym
Walls now stop at the
Learning Community
New York City College of Technology ARCH_1290 & ARCH_120
Prof.King V.1.0.docx
Building
INKED ROOF AND ROOF TRUSS
Working with an existing flat roof and truss update the roof and truss from a flat
profile to a peaked profile. In this case the Truss has been attached to the Roof.
Before we begin we will make several quick changes to the building. We will
replace the roof and parapet configuration for a roof that will ove
the face of the building, we will remove the stone coping from the top of the
wall and we will attach the top of the wall to underside of the roof.
Select the exterior wall and then select "Edit Type". Note: If you want to keep a
version of the wall with the coping stone then "Duplicate" the wall type.
all four (4) gym walls > Modify Walls > Attach Top/Base
op at the underside of the roof
Learning Community
ARCH_1290 & ARCH_1200
Page 15 of 17
Building Development | Revit
Working with an existing flat roof and truss update the roof and truss from a flat
In this case the Truss has been attached to the Roof.
Before we begin we will make several quick changes to the building. We will
replace the roof and parapet configuration for a roof that will overhang beyond
the face of the building, we will remove the stone coping from the top of the
wall and we will attach the top of the wall to underside of the roof.
". Note: If you want to keep a
" the wall type.
Modify Walls > Attach Top/Base (attach to roof)
PROF. PAUL C. KING RA
New York City College of Technology
Fall 2011
LC.1200-1290 Tutorials.03 Bldg.Gym- Prof.King V.1.0.docx
Copyright © 2011 Paul C. King
Edit Roof Footprint: Select the roof and then select "
select the double arrows
Holding Ctrl select all 4 roof sketch lines and change the
Select the (√) green
Add Roof Peak Create a peaked roof by adding slope to both long edges of the rectangular roof
From the "Gym Roof
Accept the sketch
Modify the Truss Select the Truss
Modify Roof Slope Select the Roof
Learning Community
New York City College of Technology ARCH_1290 & ARCH_120
Prof.King V.1.0.docx
Building
Select the roof and then select "Edit Footprint". Select the roof
select the double arrows. Flip the footprint so it aligns with the exterior face.
select all 4 roof sketch lines and change the overhand to 5'
√) green check mark to accept the changes to the roof sketch.
Create a peaked roof by adding slope to both long edges of the rectangular roof
Gym Roof" Level select the edge of the Roof and then "
Accept the sketch (√) and the roof and truss will both update.
russ. Change the MaxPanelWidth from 5' to 10' to update
oof. Change the slope from 9/12 to 3/ 12. The roof
Learning Community
ARCH_1290 & ARCH_1200
Page 16 of 17
Building Development | Revit
roof outline and then
the exterior face.
overhand to 5'-0"
check mark to accept the changes to the roof sketch.
Create a peaked roof by adding slope to both long edges of the rectangular roof.
and then "Edit Footprint"
and the roof and truss will both update.
to update the Truss.
roof and truss update.